From: "Johansen, Ole" <sinistre@xify.com>
To: linux-smp@vger.kernel.org
Subject: dmesg output ad IO APIC 2.4.21-pre5
Date: Fri, 28 Feb 2003 19:27:46 +0100 [thread overview]
Message-ID: <3E5FAA22.5010905@xify.com> (raw)
[-- Attachment #1: Type: text/plain, Size: 713 bytes --]
I have little clue to what this means, but it asked me to report it so I
figured I would... maybe I've configured something incorrectly... The
full dmesg output is attached.
I'm using a new mobo: Abit KD7, with an Athlon 1GHz - Just fyi.
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00178003
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0003
An unexpected IO-APIC was found. If this kernel release is less than
three months old please report this to linux-smp@vger.kernel.org
.... IRQ redirection table:
--
Ole Johansen <sinistre@xify.com>
GPG keyID 7353806D 1999-10-11
http://ole.xify.com/
[-- Attachment #2: dmesg --]
[-- Type: text/plain, Size: 11070 bytes --]
Linux version 2.4.21-pre5 (root@duramater) (gcc version 3.2.1) #6 Thu Feb 27 23:42:15 CET 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f5730
hm, page 000f5000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f1000 reserved twice.
hm, page 000f2000 reserved twice.
On node 0 totalpages: 262128
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 32752 pages.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #0 Pentium(tm) Pro APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
Enabling APIC mode: Flat. Using 1 I/O APICs
Processors: 1
Kernel command line: BOOT_IMAGE=Linux ro root=341 hdc=ide-scsi apm=off
ide_setup: hdc=ide-scsi
Initializing CPU#0
Detected 1000.433 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 1992.29 BogoMIPS
Memory: 1032852k/1048512k available (1906k kernel code, 15272k reserved, 447k data, 300k init, 131008k highmem)
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 0183fbff c1c7fbff 00000000 00000000
CPU: Common caps: 0183fbff c1c7fbff 00000000 00000000
CPU: AMD Athlon(tm) processor stepping 02
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-3, 2-7, 2-10, 2-11, 2-20 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 22.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00178003
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0003
An unexpected IO-APIC was found. If this kernel release is less than
three months old please report this to linux-smp@vger.kernel.org
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 000 00 1 0 0 0 0 0 0 00
04 001 01 0 0 0 0 0 1 1 41
05 001 01 0 0 0 0 0 1 1 49
06 001 01 0 0 0 0 0 1 1 51
07 000 00 1 0 0 0 0 0 0 00
08 001 01 0 0 0 0 0 1 1 59
09 001 01 0 0 0 0 0 1 1 61
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 001 01 0 0 0 0 0 1 1 69
0d 001 01 0 0 0 0 0 1 1 71
0e 001 01 0 0 0 0 0 1 1 79
0f 001 01 0 0 0 0 0 1 1 81
10 001 01 1 1 0 1 0 1 1 89
11 001 01 1 1 0 1 0 1 1 91
12 001 01 1 1 0 1 0 1 1 99
13 001 01 1 1 0 1 0 1 1 A1
14 000 00 1 0 0 0 0 0 0 00
15 001 01 1 1 0 1 0 1 1 A9
16 001 01 1 1 0 1 0 1 1 B1
17 001 01 1 1 0 1 0 1 1 B9
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ21 -> 0:21
IRQ22 -> 0:22
IRQ23 -> 0:23
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1000.4813 MHz.
..... host bus clock speed is 266.7950 MHz.
cpu: 0, clocks: 2667950, slice: 1333975
CPU0<T0:2667936,T1:1333952,D:9,S:1333975,C:2667950>
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfb4e0, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router VIA [1106/3177] at 00:11.0
PCI->APIC IRQ transform: (B0,I10,P0) -> 17
PCI->APIC IRQ transform: (B0,I12,P0) -> 18
PCI->APIC IRQ transform: (B0,I16,P0) -> 21
PCI->APIC IRQ transform: (B0,I16,P1) -> 21
PCI->APIC IRQ transform: (B0,I16,P2) -> 21
PCI->APIC IRQ transform: (B0,I16,P3) -> 19
PCI->APIC IRQ transform: (B0,I17,P0) -> 22
PCI->APIC IRQ transform: (B0,I17,P2) -> 22
PCI->APIC IRQ transform: (B0,I18,P0) -> 23
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
PCI: Via IRQ fixup for 00:10.0, from 11 to 5
PCI: Via IRQ fixup for 00:10.1, from 10 to 5
PCI: Via IRQ fixup for 00:10.2, from 7 to 5
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
allocated 32 pages and 32 bhs reserved for the highmem bounces
Journalled Block Device driver loaded
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
NTFS driver v1.1.22 [Flags: R/O]
ACPI: Core Subsystem version [20011018]
ACPI: Subsystem enabled
ACPI: System firmware supports S0 S1 S4 S5
Processor[0]: C0 C1 C2, 2 throttling states
vesafb: framebuffer at 0xd0000000, mapped to 0xf881a000, size 65536k
vesafb: mode is 1024x768x16, linelength=2048, pages=0
vesafb: protected mode interface info at c000:bff0
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled
Real Time Clock Driver v1.10e
via-rhine.c:v1.10-LK1.1.16 February-15-2003 Written by Donald Becker
http://www.scyld.com/network/via-rhine.html
eth0: VIA VT6102 Rhine-II at 0xe800, 00:50:8d:48:08:c2, IRQ 23.
eth0: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000.
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: Detected Via Apollo Pro KT400 chipset
agpgart: AGP aperture is 256M @ 0xc0000000
Uniform Multi-Platform E-IDE driver Revision: 7.00beta-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:11.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci00:11.1
ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:pio
hda: Maxtor 4D060H3, ATA DISK drive
hdb: WDC WD1200JB-00CRA1, ATA DISK drive
blk: queue c03c9840, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c03c997c, I/O limit 4095Mb (mask 0xffffffff)
hdc: PHILIPS CDRW1610A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: host protected area => 1
hda: 120069936 sectors (61476 MB) w/2048KiB Cache, CHS=7474/255/63, UDMA(133)
hdb: host protected area => 1
hdb: 234441648 sectors (120034 MB) w/8192KiB Cache, CHS=14593/255/63, UDMA(100)
ide-floppy driver 0.99.newide
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2
/dev/ide/host0/bus0/target1/lun0: p1 p2 p3 p4 < p5 p6 >
ide-floppy driver 0.99.newide
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: PHILIPS Model: CDRW1610A Rev: 02B0
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
ISDN subsystem Rev: 1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1
PPP BSD Compression module registered
HiSax: Linux Driver for passive ISDN cards
HiSax: Version 3.5 (kernel)
HiSax: Layer1 Revision 1.1.4.1
HiSax: Layer2 Revision 1.1.4.1
HiSax: TeiMgr Revision 1.1.4.1
HiSax: Layer3 Revision 1.1.4.1
HiSax: LinkLayer Revision 1.1.4.1
HiSax: Approval certification valid
HiSax: Approved with ELSA Microlink PCI cards
HiSax: Approved with Eicon Technology Diva 2.01 PCI cards
HiSax: Approved with Sedlbauer Speedfax + cards
HiSax: Approved with HFC-S PCI A based cards
HiSax: Total 1 card defined
HiSax: Card 1 Protocol EDSS1 Id=HiSax (0)
HiSax: W6692 driver Rev. 1.1.4.1
Found: Dynalink/AsusCom IS64PH, I/O base: 0xd000, irq: 17
HiSax: IS64PH config irq:17 I/O:d000
W6692: Winbond W6692 version (0): W6692 V00
W6692 ISTA=0x0
W6692 IMASK=0xFF
W6692 D_EXIR=0x0
W6692 D_EXIM=0xFF
W6692 D_RSTA=0xA0
Winbond 6692: IRQ 17 count 0
Winbond 6692: IRQ 17 count 4
HiSax: DSS1 Rev. 1.1.4.1
HiSax: 2 channels added
HiSax: MAX_WAITING_CALLS added
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
ip_conntrack version 2.1 (8191 buckets, 65528 max) - 292 bytes per conntrack
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 300k freed
Adding Swap: 262136k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,65), internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,66), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,67), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
0: nvidia: loading NVIDIA Linux x86 nvidia.o Kernel Module 1.0-4191 Mon Dec 9 11:49:01 PST 2002
PCI: Setting latency timer of device 00:11.5 to 64
reply other threads:[~2003-02-28 18:27 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3E5FAA22.5010905@xify.com \
--to=sinistre@xify.com \
--cc=linux-smp@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox