From: Bo Shen <voice.shen@atmel.com>
To: broonie@opensource.wolfsonmicro.com, plagnioj@jcrosoft.com,
nicolas.ferre@atmel.com
Cc: linux-arm-kernel@lists.infradead.org,
devicetree-discuss@lists.ozlabs.org, linux-sound@vger.kernel.org,
alsa-devel@alsa-project.org, Bo Shen <voice.shen@atmel.com>
Subject: [Resend v6 PATCH 1/2] ARM: at91: atmel-ssc: add pinctrl nodes
Date: Fri, 16 Nov 2012 06:03:56 +0000 [thread overview]
Message-ID: <1353045837-19474-1-git-send-email-voice.shen@atmel.com> (raw)
Add pinctrl nodes for atmel ssc peripheral
Signed-off-by: Bo Shen <voice.shen@atmel.com>
---
Resend:
Split one patch into two.
- one add pinctrl nodes
- one add pinctrl consumer
---
arch/arm/boot/dts/at91sam9260.dtsi | 18 ++++++++++++++++++
arch/arm/boot/dts/at91sam9263.dtsi | 36 ++++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/at91sam9g45.dtsi | 36 ++++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/at91sam9n12.dtsi | 26 ++++++++++++++++++++++++++
arch/arm/boot/dts/at91sam9x5.dtsi | 32 +++++++++++++++++++++++++-------
5 files changed, 141 insertions(+), 7 deletions(-)
diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/at91sam9260.dtsi
index 3164dcd..f9dc7db 100644
--- a/arch/arm/boot/dts/at91sam9260.dtsi
+++ b/arch/arm/boot/dts/at91sam9260.dtsi
@@ -217,6 +217,22 @@
};
};
+ ssc0 {
+ pinctrl_ssc0_tx: ssc0_tx-0 {
+ atmel,pins + <1 16 0x1 0x0 /* PB16 periph A */
+ 1 17 0x1 0x0 /* PB17 periph A */
+ 1 18 0x1 0x0>; /* PB18 periph A */
+ };
+
+ pinctrl_ssc0_rx: ssc0_rx-0 {
+ atmel,pins + <1 19 0x1 0x0 /* PB19 periph A */
+ 1 20 0x1 0x0 /* PB20 periph A */
+ 1 21 0x1 0x0>; /* PB21 periph A */
+ };
+ };
+
pioA: gpio@fffff400 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x200>;
@@ -350,6 +366,8 @@
compatible = "atmel,at91rm9200-ssc";
reg = <0xfffbc000 0x4000>;
interrupts = <14 4 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
status = "disable";
};
diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi
index 96e0bc9..6e9a4ff 100644
--- a/arch/arm/boot/dts/at91sam9263.dtsi
+++ b/arch/arm/boot/dts/at91sam9263.dtsi
@@ -165,6 +165,38 @@
};
};
+ ssc0 {
+ pinctrl_ssc0_tx: ssc0_tx-0 {
+ atmel,pins + <1 0 0x2 0x0 /* PB0 periph B */
+ 1 1 0x2 0x0 /* PB1 periph B */
+ 1 2 0x2 0x0>; /* PB2 periph B */
+ };
+
+ pinctrl_ssc0_rx: ssc0_rx-0 {
+ atmel,pins + <1 3 0x2 0x0 /* PB3 periph B */
+ 1 4 0x2 0x0 /* PB4 periph B */
+ 1 5 0x2 0x0>; /* PB5 periph B */
+ };
+ };
+
+ ssc1 {
+ pinctrl_ssc1_tx: ssc1_tx-0 {
+ atmel,pins + <1 6 0x1 0x0 /* PB6 periph A */
+ 1 7 0x1 0x0 /* PB7 periph A */
+ 1 8 0x1 0x0>; /* PB8 periph A */
+ };
+
+ pinctrl_ssc1_rx: ssc1_rx-0 {
+ atmel,pins + <1 9 0x1 0x0 /* PB9 periph A */
+ 1 10 0x1 0x0 /* PB10 periph A */
+ 1 11 0x1 0x0>; /* PB11 periph A */
+ };
+ };
+
pioA: gpio@fffff200 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff200 0x200>;
@@ -262,6 +294,8 @@
compatible = "atmel,at91rm9200-ssc";
reg = <0xfff98000 0x4000>;
interrupts = <16 4 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
status = "disable";
};
@@ -269,6 +303,8 @@
compatible = "atmel,at91rm9200-ssc";
reg = <0xfff9c000 0x4000>;
interrupts = <17 4 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>;
status = "disable";
};
diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi
index c40c3eb..63cf206 100644
--- a/arch/arm/boot/dts/at91sam9g45.dtsi
+++ b/arch/arm/boot/dts/at91sam9g45.dtsi
@@ -198,6 +198,38 @@
};
};
+ ssc0 {
+ pinctrl_ssc0_tx: ssc0_tx-0 {
+ atmel,pins + <3 0 0x1 0x0 /* PD0 periph A */
+ 3 1 0x1 0x0 /* PD1 periph A */
+ 3 2 0x1 0x0>; /* PD2 periph A */
+ };
+
+ pinctrl_ssc0_rx: ssc0_rx-0 {
+ atmel,pins + <3 3 0x1 0x0 /* PD3 periph A */
+ 3 4 0x1 0x0 /* PD4 periph A */
+ 3 5 0x1 0x0>; /* PD5 periph A */
+ };
+ };
+
+ ssc1 {
+ pinctrl_ssc1_tx: ssc1_tx-0 {
+ atmel,pins + <3 10 0x1 0x0 /* PD10 periph A */
+ 3 11 0x1 0x0 /* PD11 periph A */
+ 3 12 0x1 0x0>; /* PD12 periph A */
+ };
+
+ pinctrl_ssc1_rx: ssc1_rx-0 {
+ atmel,pins + <3 13 0x1 0x0 /* PD13 periph A */
+ 3 14 0x1 0x0 /* PD14 periph A */
+ 3 15 0x1 0x0>; /* PD15 periph A */
+ };
+ };
+
pioA: gpio@fffff200 {
compatible = "atmel,at91rm9200-gpio";
reg = <0xfffff200 0x200>;
@@ -331,6 +363,8 @@
compatible = "atmel,at91sam9g45-ssc";
reg = <0xfff9c000 0x4000>;
interrupts = <16 4 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
status = "disable";
};
@@ -338,6 +372,8 @@
compatible = "atmel,at91sam9g45-ssc";
reg = <0xfffa0000 0x4000>;
interrupts = <17 4 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ssc1_tx &pinctrl_ssc1_rx>;
status = "disable";
};
diff --git a/arch/arm/boot/dts/at91sam9n12.dtsi b/arch/arm/boot/dts/at91sam9n12.dtsi
index 7b644c5..b211da6 100644
--- a/arch/arm/boot/dts/at91sam9n12.dtsi
+++ b/arch/arm/boot/dts/at91sam9n12.dtsi
@@ -28,6 +28,7 @@
tcb1 = &tcb1;
i2c0 = &i2c0;
i2c1 = &i2c1;
+ ssc0 = &ssc0;
};
cpus {
cpu@0 {
@@ -199,6 +200,22 @@
};
};
+ ssc0 {
+ pinctrl_ssc0_tx: ssc0_tx-0 {
+ atmel,pins + <0 24 0x2 0x0 /* PA24 periph B */
+ 0 25 0x2 0x0 /* PA25 periph B */
+ 0 26 0x2 0x0>; /* PA26 periph B */
+ };
+
+ pinctrl_ssc0_rx: ssc0_rx-0 {
+ atmel,pins + <0 27 0x2 0x0 /* PA27 periph B */
+ 0 28 0x2 0x0 /* PA28 periph B */
+ 0 29 0x2 0x0>; /* PA29 periph B */
+ };
+ };
+
pioA: gpio@fffff400 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x200>;
@@ -249,6 +266,15 @@
status = "disabled";
};
+ ssc0: ssc@f0010000 {
+ compatible = "atmel,at91sam9g45-ssc";
+ reg = <0xf0010000 0x4000>;
+ interrupts = <28 4 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
+ status = "disable";
+ };
+
usart0: serial@f801c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf801c000 0x4000>;
diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi
index 1cb26c28..df84f39 100644
--- a/arch/arm/boot/dts/at91sam9x5.dtsi
+++ b/arch/arm/boot/dts/at91sam9x5.dtsi
@@ -88,13 +88,6 @@
interrupts = <1 4 7>;
};
- ssc0: ssc@f0010000 {
- compatible = "atmel,at91sam9g45-ssc";
- reg = <0xf0010000 0x4000>;
- interrupts = <28 4 5>;
- status = "disable";
- };
-
tcb0: timer@f8008000 {
compatible = "atmel,at91sam9x5-tcb";
reg = <0xf8008000 0x100>;
@@ -214,6 +207,22 @@
};
};
+ ssc0 {
+ pinctrl_ssc0_tx: ssc0_tx-0 {
+ atmel,pins + <0 24 0x2 0x0 /* PA24 periph B */
+ 0 25 0x2 0x0 /* PA25 periph B */
+ 0 26 0x2 0x0>; /* PA26 periph B */
+ };
+
+ pinctrl_ssc0_rx: ssc0_rx-0 {
+ atmel,pins + <0 27 0x2 0x0 /* PA27 periph B */
+ 0 28 0x2 0x0 /* PA28 periph B */
+ 0 29 0x2 0x0>; /* PA29 periph B */
+ };
+ };
+
pioA: gpio@fffff400 {
compatible = "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
reg = <0xfffff400 0x200>;
@@ -266,6 +275,15 @@
status = "disabled";
};
+ ssc0: ssc@f0010000 {
+ compatible = "atmel,at91sam9g45-ssc";
+ reg = <0xf0010000 0x4000>;
+ interrupts = <28 4 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
+ status = "disable";
+ };
+
usart0: serial@f801c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf801c000 0x200>;
--
1.7.9.5
next reply other threads:[~2012-11-16 6:03 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-11-16 6:03 Bo Shen [this message]
2012-11-16 6:03 ` [Resend v6 PATCH 2/2] ASoC: atmel-ssc: add pinctrl consumer Bo Shen
2012-11-16 6:12 ` Mark Brown
2012-11-16 6:33 ` Bo Shen
2012-11-16 6:41 ` Mark Brown
2012-11-16 6:59 ` Bo Shen
2012-11-20 9:31 ` Bo Shen
2012-11-20 10:27 ` Mark Brown
2012-11-21 1:43 ` Bo Shen
2012-11-21 1:46 ` Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1353045837-19474-1-git-send-email-voice.shen@atmel.com \
--to=voice.shen@atmel.com \
--cc=alsa-devel@alsa-project.org \
--cc=broonie@opensource.wolfsonmicro.com \
--cc=devicetree-discuss@lists.ozlabs.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-sound@vger.kernel.org \
--cc=nicolas.ferre@atmel.com \
--cc=plagnioj@jcrosoft.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox