From: Alexander Stein <alexander.stein@ew.tq-group.com>
To: Shenghao Ding <shenghao-ding@ti.com>, Kevin Lu <kevin-lu@ti.com>,
Baojun Xu <baojun.xu@ti.com>, Jaroslav Kysela <perex@perex.cz>,
Takashi Iwai <tiwai@suse.com>,
Liam Girdwood <lgirdwood@gmail.com>,
Mark Brown <broonie@kernel.org>,
Linus Walleij <linus.walleij@linaro.org>,
Bartosz Golaszewski <brgl@bgdev.pl>, Peng Fan <peng.fan@nxp.com>
Cc: linux-sound@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-gpio@vger.kernel.org, Peng Fan <peng.fan@nxp.com>,
Markus Niebel <Markus.Niebel@ew.tq-group.com>
Subject: Re: [PATCH 2/2] ASoC: codec: tlv320aic32x4: Convert to GPIO descriptors
Date: Mon, 07 Jul 2025 07:22:57 +0200 [thread overview]
Message-ID: <3372384.44csPzL39Z@steina-w> (raw)
In-Reply-To: <20250706-asoc-gpio-1-v1-2-f0912095e923@nxp.com>
Hi,
Am Sonntag, 6. Juli 2025, 03:04:24 CEST schrieb Peng Fan:
> of_gpio.h is deprecated, update the driver to use GPIO descriptors.
> - Use devm_gpiod_get_optional to get GPIO descriptor, and set consumer
> name.
> - Use gpiod_set_value to configure output value.
>
> While at here, reorder the included headers.
>
> Checking the DTS that use the device, all are using GPIOD_ACTIVE_LOW
> polarity for reset-gpios, so all should work as expected with this patch.
>
> Cc: Markus Niebel <Markus.Niebel@ew.tq-group.com>
> Cc: Alexander Stein <alexander.stein@ew.tq-group.com>
> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
> Signed-off-by: Peng Fan <peng.fan@nxp.com>
> ---
> sound/soc/codecs/tlv320aic32x4.c | 44 ++++++++++++++++++++--------------------
> 1 file changed, 22 insertions(+), 22 deletions(-)
>
> diff --git a/sound/soc/codecs/tlv320aic32x4.c b/sound/soc/codecs/tlv320aic32x4.c
> index 7dbcf7f7130b04a27f58f20beb83eb3676c79c3d..1423186f5a6c181a20dd2dd552679d33174edaee 100644
> --- a/sound/soc/codecs/tlv320aic32x4.c
> +++ b/sound/soc/codecs/tlv320aic32x4.c
> @@ -9,27 +9,26 @@
> * Based on sound/soc/codecs/wm8974 and TI driver for kernel 2.6.27.
> */
>
> -#include <linux/module.h>
> -#include <linux/moduleparam.h>
> -#include <linux/init.h>
> -#include <linux/delay.h>
> -#include <linux/pm.h>
> -#include <linux/gpio.h>
> -#include <linux/of_gpio.h>
> #include <linux/cdev.h>
> -#include <linux/slab.h>
> #include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/init.h>
> +#include <linux/module.h>
> +#include <linux/moduleparam.h>
> #include <linux/of_clk.h>
> +#include <linux/pm.h>
> #include <linux/regulator/consumer.h>
> +#include <linux/slab.h>
>
> -#include <sound/tlv320aic32x4.h>
> #include <sound/core.h>
> +#include <sound/initval.h>
> #include <sound/pcm.h>
> #include <sound/pcm_params.h>
> #include <sound/soc.h>
> #include <sound/soc-dapm.h>
> -#include <sound/initval.h>
> #include <sound/tlv.h>
> +#include <sound/tlv320aic32x4.h>
Mh, maybe create a single commit sorting these headers.
>
> #include "tlv320aic32x4.h"
>
> @@ -38,7 +37,7 @@ struct aic32x4_priv {
> u32 power_cfg;
> u32 micpga_routing;
> bool swapdacs;
> - int rstn_gpio;
> + struct gpio_desc *rstn_gpio;
> const char *mclk_name;
>
> struct regulator *supply_ldo;
> @@ -1236,7 +1235,14 @@ static int aic32x4_parse_dt(struct aic32x4_priv *aic32x4,
>
> aic32x4->swapdacs = false;
> aic32x4->micpga_routing = 0;
> - aic32x4->rstn_gpio = of_get_named_gpio(np, "reset-gpios", 0);
> + /* Assert reset using GPIOD_OUT_HIGH, because reset is GPIO_ACTIVE_LOW */
> + aic32x4->rstn_gpio = devm_gpiod_get_optional(aic32x4->dev, "reset", GPIOD_OUT_HIGH);
> + if (IS_ERR(aic32x4->rstn_gpio)) {
> + return dev_err_probe(aic32x4->dev, PTR_ERR(aic32x4->rstn_gpio),
> + "Failed to get reset gpio\n");
> + } else {
> + gpiod_set_consumer_name(aic32x4->rstn_gpio, "tlv320aic32x4_rstn");
> + }
>
> if (of_property_read_u32_array(np, "aic32x4-gpio-func",
> aic32x4_setup->gpio_func, 5) >= 0)
> @@ -1372,26 +1378,20 @@ int aic32x4_probe(struct device *dev, struct regmap *regmap,
> aic32x4->power_cfg = 0;
> aic32x4->swapdacs = false;
> aic32x4->micpga_routing = 0;
> - aic32x4->rstn_gpio = -1;
> + aic32x4->rstn_gpio = ERR_PTR(-ENOENT);
Shouldn't this be NULL similar to when devm_gpiod_get_optional() doesn't
find any reset GPIO?
Despite that, looks good and works as intended:
Tested-By: Alexander Stein <alexander.stein@ew.tq-group.com>
> aic32x4->mclk_name = "mclk";
> }
>
> - if (gpio_is_valid(aic32x4->rstn_gpio)) {
> - ret = devm_gpio_request_one(dev, aic32x4->rstn_gpio,
> - GPIOF_OUT_INIT_LOW, "tlv320aic32x4 rstn");
> - if (ret != 0)
> - return ret;
> - }
> -
> ret = aic32x4_setup_regulators(dev, aic32x4);
> if (ret) {
> dev_err(dev, "Failed to setup regulators\n");
> return ret;
> }
>
> - if (gpio_is_valid(aic32x4->rstn_gpio)) {
> + if (!IS_ERR(aic32x4->rstn_gpio)) {
> ndelay(10);
> - gpio_set_value_cansleep(aic32x4->rstn_gpio, 1);
> + /* deassert reset */
> + gpiod_set_value_cansleep(aic32x4->rstn_gpio, 0);
> mdelay(1);
> }
>
>
>
--
TQ-Systems GmbH | Mühlstraße 2, Gut Delling | 82229 Seefeld, Germany
Amtsgericht München, HRB 105018
Geschäftsführer: Detlef Schneider, Rüdiger Stahl, Stefan Schneider
http://www.tq-group.com/
next prev parent reply other threads:[~2025-07-07 5:23 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-07-06 1:04 [PATCH 0/2] ASoC: codec: Convert to GPIO descriptors for tlv320aic32x4 Peng Fan
2025-07-06 1:04 ` [PATCH 1/2] ASoC: codec: tlv320aic32x4: Drop aic32x4_pdata usage Peng Fan
2025-07-07 5:12 ` Alexander Stein
2025-07-06 1:04 ` [PATCH 2/2] ASoC: codec: tlv320aic32x4: Convert to GPIO descriptors Peng Fan
2025-07-07 5:22 ` Alexander Stein [this message]
2025-07-07 5:40 ` Peng Fan
2025-07-07 5:44 ` Alexander Stein
2025-07-07 6:46 ` Peng Fan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3372384.44csPzL39Z@steina-w \
--to=alexander.stein@ew.tq-group.com \
--cc=Markus.Niebel@ew.tq-group.com \
--cc=baojun.xu@ti.com \
--cc=brgl@bgdev.pl \
--cc=broonie@kernel.org \
--cc=kevin-lu@ti.com \
--cc=lgirdwood@gmail.com \
--cc=linus.walleij@linaro.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-sound@vger.kernel.org \
--cc=peng.fan@nxp.com \
--cc=perex@perex.cz \
--cc=shenghao-ding@ti.com \
--cc=tiwai@suse.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox