[PATCH 16/16] Blackfin SPI Driver: fix bug - correct usage of struct spi_transfer.cs_change

[Bryan Wu <cooloney-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>]

From: Yi Li <yi.li-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>

According to comments in linux/spi/spi.h:

 * All SPI transfers start with the relevant chipselect active.  Normally
 * it stays selected until after the last transfer in a message. Drivers
 * can affect the chipselect signal using cs_change.
 *
 * (i) If the transfer isn't the last one in the message, this flag is
 * used to make the chipselect briefly go inactive in the middle of the
 * message.  Toggling chipselect in this way may be needed to terminate
 * a chip command, letting a single spi_message perform all of group of
 * chip transactions together.
 *
 * (ii) When the transfer is the last one in the message, the chip may
 * stay selected until the next transfer.  On multi-device SPI busses
 * with nothing blocking messages going to other devices, this is just
 * a performance hint; starting a message to another device deselects
 * this one.  But in other cases, this can be used to ensure correctness.
 * Some devices need protocol transactions to be built from a series of
 * spi_message submissions, where the content of one message is determined
 * by the results of previous messages and where the whole transaction
 * ends when the chipselect goes intactive.

Signed-off-by: Yi Li <yi.li-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
Signed-off-by: Bryan Wu <cooloney-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |   15 ++++++++-------
 1 files changed, 8 insertions(+), 7 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index 8cf5d6e..0e3102a 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -540,15 +540,13 @@ static void giveback(struct driver_data *drv_data)
 
 	msg->state = NULL;
 
-	/* disable chip select signal. And not stop spi in autobuffer mode */
-	if (drv_data->tx_dma != 0xFFFF) {
-		cs_deactive(drv_data, chip);
-		bfin_spi_disable(drv_data);
-	}
-
 	if (!drv_data->cs_change)
 		cs_deactive(drv_data, chip);
 
+	/* Not stop spi in autobuffer mode */
+	if (drv_data->tx_dma != 0xFFFF)
+		bfin_spi_disable(drv_data);
+
 	if (msg->complete)
 		msg->complete(msg->context);
 }
@@ -757,7 +755,8 @@ static void pump_transfers(unsigned long data)
 
 	write_STAT(drv_data, BIT_STAT_CLR);
 	cr = (read_CTRL(drv_data) & (~BIT_CTL_TIMOD));
-	cs_active(drv_data, chip);
+	if (drv_data->cs_change)
+		cs_active(drv_data, chip);
 
 	dev_dbg(&drv_data->pdev->dev,
 		"now pumping a transfer: width is %d, len is %d\n",
@@ -920,6 +919,8 @@ static void pump_transfers(unsigned long data)
 			message->state = next_transfer(drv_data);
 		}
 
+		if (drv_data->cs_change)
+			cs_active(drv_data, chip);
 		/* Schedule next transfer tasklet */
 		tasklet_schedule(&drv_data->pump_transfers);
 
-- 
1.5.6.3

-------------------------------------------------------------------------
This SF.Net email is sponsored by the Moblin Your Move Developer's challenge
Build the coolest Linux based applications with Moblin SDK & win great prizes
Grand prize is a trip for two to an Open Source event anywhere in the world
http://moblin-contest.org/redirect.php?banner_id=100&url=/