From: Erik Gilling <konkers-z5hGa2qSFaRBDgjK7y7TUQ@public.gmane.org>
To: linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: Russell King <linux-lFZ/pmaqli7XmaaqVzeoHQ@public.gmane.org>,
Erik Gilling <konkers-z5hGa2qSFaRBDgjK7y7TUQ@public.gmane.org>,
spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
Subject: [PATCH v3] spi: add spi_tegra driver
Date: Wed, 25 Aug 2010 14:23:15 -0700 [thread overview]
Message-ID: <1282771395-21684-1-git-send-email-konkers@android.com> (raw)
In-Reply-To: <1281574023-25160-1-git-send-email-konkers-z5hGa2qSFaRBDgjK7y7TUQ@public.gmane.org>
v2 changes:
from Thierry Reding:
* add "select TEGRA_SYSTEM_DMA" to Kconfig
from Grant Likely:
* add oneline description to header
* inline references to DRIVER_NAME
* inline references to BUSY_TIMEOUT
* open coded bytes_per_word()
* spi_readl/writel -> spi_tegra_readl/writel
* move transfer validation to spi_tegra_transfer
* don't request_mem_region iomem as platform bus does that for us
* __exit -> __devexit
v3 changes:
from Russell King:
* put request_mem_region back int
from Grant Likely:
* remove #undef DEBUG
* add SLINK_ to register bit defines
* remove unused bytes_per_word
* make spi_tegra_readl/writel static linine
* various refactoring for clarity
* mark err if BSY bit is not cleared after 1000 retries
* move spinlock to protect setting of RDY bit
* subsys_initcall -> module_init
Signed-off-by: Erik Gilling <konkers-z5hGa2qSFaRBDgjK7y7TUQ@public.gmane.org>
Cc: Thierry Reding <thierry.reding-RM9K5IK7kjKj5M59NBduVrNAH6kLmebB@public.gmane.org>
Cc: Grant Likely <grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org>
Cc: Russell King <linux-lFZ/pmaqli7XmaaqVzeoHQ@public.gmane.org>
---
drivers/spi/Kconfig | 7 +
drivers/spi/Makefile | 1 +
drivers/spi/spi_tegra.c | 625 +++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 633 insertions(+), 0 deletions(-)
create mode 100644 drivers/spi/spi_tegra.c
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 91c2f4f..9fdb309 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -298,6 +298,13 @@ config SPI_STMP3XXX
help
SPI driver for Freescale STMP37xx/378x SoC SSP interface
+config SPI_TEGRA
+ tristate "Nvidia Tegra SPI controller"
+ depends on ARCH_TEGRA
+ select TEGRA_SYSTEM_DMA
+ help
+ SPI driver for NVidia Tegra SoCs
+
config SPI_TXX9
tristate "Toshiba TXx9 SPI controller"
depends on GENERIC_GPIO && CPU_TX49XX
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index e9cbd18..b6573d8 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -39,6 +39,7 @@ obj-$(CONFIG_SPI_PPC4xx) += spi_ppc4xx.o
obj-$(CONFIG_SPI_S3C24XX_GPIO) += spi_s3c24xx_gpio.o
obj-$(CONFIG_SPI_S3C24XX) += spi_s3c24xx_hw.o
obj-$(CONFIG_SPI_S3C64XX) += spi_s3c64xx.o
+obj-$(CONFIG_SPI_TEGRA) += spi_tegra.o
obj-$(CONFIG_SPI_TXX9) += spi_txx9.o
obj-$(CONFIG_SPI_XILINX) += xilinx_spi.o
obj-$(CONFIG_SPI_XILINX_OF) += xilinx_spi_of.o
diff --git a/drivers/spi/spi_tegra.c b/drivers/spi/spi_tegra.c
new file mode 100644
index 0000000..cd9f19b
--- /dev/null
+++ b/drivers/spi/spi_tegra.c
@@ -0,0 +1,625 @@
+/*
+ * Driver for Nvidia TEGRA spi controller.
+ *
+ * Copyright (C) 2010 Google, Inc.
+ *
+ * Author:
+ * Erik Gilling <konkers-z5hGa2qSFaRBDgjK7y7TUQ@public.gmane.org>
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmapool.h>
+#include <linux/clk.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+
+#include <linux/spi/spi.h>
+
+#include <mach/dma.h>
+
+#define SLINK_COMMAND 0x000
+#define SLINK_BIT_LENGTH(x) (((x) & 0x1f) << 0)
+#define SLINK_WORD_SIZE(x) (((x) & 0x1f) << 5)
+#define SLINK_BOTH_EN (1 << 10)
+#define SLINK_CS_SW (1 << 11)
+#define SLINK_CS_VALUE (1 << 12)
+#define SLINK_CS_POLARITY (1 << 13)
+#define SLINK_IDLE_SDA_DRIVE_LOW (0 << 16)
+#define SLINK_IDLE_SDA_DRIVE_HIGH (1 << 16)
+#define SLINK_IDLE_SDA_PULL_LOW (2 << 16)
+#define SLINK_IDLE_SDA_PULL_HIGH (3 << 16)
+#define SLINK_IDLE_SDA_MASK (3 << 16)
+#define SLINK_CS_POLARITY1 (1 << 20)
+#define SLINK_CK_SDA (1 << 21)
+#define SLINK_CS_POLARITY2 (1 << 22)
+#define SLINK_CS_POLARITY3 (1 << 23)
+#define SLINK_IDLE_SCLK_DRIVE_LOW (0 << 24)
+#define SLINK_IDLE_SCLK_DRIVE_HIGH (1 << 24)
+#define SLINK_IDLE_SCLK_PULL_LOW (2 << 24)
+#define SLINK_IDLE_SCLK_PULL_HIGH (3 << 24)
+#define SLINK_IDLE_SCLK_MASK (3 << 24)
+#define SLINK_M_S (1 << 28)
+#define SLINK_WAIT (1 << 29)
+#define SLINK_GO (1 << 30)
+#define SLINK_ENB (1 << 31)
+
+#define SLINK_COMMAND2 0x004
+#define SLINK_LSBFE (1 << 0)
+#define SLINK_SSOE (1 << 1)
+#define SLINK_SPIE (1 << 4)
+#define SLINK_BIDIROE (1 << 6)
+#define SLINK_MODFEN (1 << 7)
+#define SLINK_INT_SIZE(x) (((x) & 0x1f) << 8)
+#define SLINK_CS_ACTIVE_BETWEEN (1 << 17)
+#define SLINK_SS_EN_CS(x) (((x) & 0x3) << 18)
+#define SLINK_SS_SETUP(x) (((x) & 0x3) << 20)
+#define SLINK_FIFO_REFILLS_0 (0 << 22)
+#define SLINK_FIFO_REFILLS_1 (1 << 22)
+#define SLINK_FIFO_REFILLS_2 (2 << 22)
+#define SLINK_FIFO_REFILLS_3 (3 << 22)
+#define SLINK_FIFO_REFILLS_MASK (3 << 22)
+#define SLINK_WAIT_PACK_INT(x) (((x) & 0x7) << 26)
+#define SLINK_SPC0 (1 << 29)
+#define SLINK_TXEN (1 << 30)
+#define SLINK_RXEN (1 << 31)
+
+#define SLINK_STATUS 0x008
+#define SLINK_COUNT(val) (((val) >> 0) & 0x1f)
+#define SLINK_WORD(val) (((val) >> 5) & 0x1f)
+#define SLINK_BLK_CNT(val) (((val) >> 0) & 0xffff)
+#define SLINK_MODF (1 << 16)
+#define SLINK_RX_UNF (1 << 18)
+#define SLINK_TX_OVF (1 << 19)
+#define SLINK_TX_FULL (1 << 20)
+#define SLINK_TX_EMPTY (1 << 21)
+#define SLINK_RX_FULL (1 << 22)
+#define SLINK_RX_EMPTY (1 << 23)
+#define SLINK_TX_UNF (1 << 24)
+#define SLINK_RX_OVF (1 << 25)
+#define SLINK_TX_FLUSH (1 << 26)
+#define SLINK_RX_FLUSH (1 << 27)
+#define SLINK_SCLK (1 << 28)
+#define SLINK_ERR (1 << 29)
+#define SLINK_RDY (1 << 30)
+#define SLINK_BSY (1 << 31)
+
+#define SLINK_MAS_DATA 0x010
+#define SLINK_SLAVE_DATA 0x014
+
+#define SLINK_DMA_CTL 0x018
+#define SLINK_DMA_BLOCK_SIZE(x) (((x) & 0xffff) << 0)
+#define SLINK_TX_TRIG_1 (0 << 16)
+#define SLINK_TX_TRIG_4 (1 << 16)
+#define SLINK_TX_TRIG_8 (2 << 16)
+#define SLINK_TX_TRIG_16 (3 << 16)
+#define SLINK_TX_TRIG_MASK (3 << 16)
+#define SLINK_RX_TRIG_1 (0 << 18)
+#define SLINK_RX_TRIG_4 (1 << 18)
+#define SLINK_RX_TRIG_8 (2 << 18)
+#define SLINK_RX_TRIG_16 (3 << 18)
+#define SLINK_RX_TRIG_MASK (3 << 18)
+#define SLINK_PACKED (1 << 20)
+#define SLINK_PACK_SIZE_4 (0 << 21)
+#define SLINK_PACK_SIZE_8 (1 << 21)
+#define SLINK_PACK_SIZE_16 (2 << 21)
+#define SLINK_PACK_SIZE_32 (3 << 21)
+#define SLINK_PACK_SIZE_MASK (3 << 21)
+#define SLINK_IE_TXC (1 << 26)
+#define SLINK_IE_RXC (1 << 27)
+#define SLINK_DMA_EN (1 << 31)
+
+#define SLINK_STATUS2 0x01c
+#define SLINK_TX_FIFO_EMPTY_COUNT(val) (((val) & 0x3f) >> 0)
+#define SLINK_RX_FIFO_FULL_COUNT(val) (((val) & 0x3f) >> 16)
+
+#define SLINK_TX_FIFO 0x100
+#define SLINK_RX_FIFO 0x180
+
+static const unsigned long spi_tegra_req_sels[] = {
+ TEGRA_DMA_REQ_SEL_SL2B1,
+ TEGRA_DMA_REQ_SEL_SL2B2,
+ TEGRA_DMA_REQ_SEL_SL2B3,
+ TEGRA_DMA_REQ_SEL_SL2B4,
+};
+
+#define BB_LEN 32
+
+struct spi_tegra_data {
+ struct spi_master *master;
+ struct platform_device *pdev;
+ spinlock_t lock;
+
+ struct clk *clk;
+ void __iomem *base;
+ unsigned long phys;
+
+ u32 cur_speed;
+
+ struct list_head queue;
+ struct spi_transfer *cur;
+ unsigned cur_pos;
+ unsigned cur_len;
+ unsigned cur_bytes_per_word;
+
+ /* The tegra spi controller has a bug which causes the first word
+ * in PIO transactions to be garbage. Since packed DMA transactions
+ * require transfers to be 4 byte aligned we need a bounce buffer
+ * for the generic case.
+ */
+ struct tegra_dma_req rx_dma_req;
+ struct tegra_dma_channel *rx_dma;
+ u32 *rx_bb;
+ dma_addr_t rx_bb_phys;
+};
+
+
+static inline unsigned long spi_tegra_readl(struct spi_tegra_data *tspi,
+ unsigned long reg)
+{
+ return readl(tspi->base + reg);
+}
+
+static inline void spi_tegra_writel(struct spi_tegra_data *tspi,
+ unsigned long val,
+ unsigned long reg)
+{
+ writel(val, tspi->base + reg);
+}
+
+static void spi_tegra_go(struct spi_tegra_data *tspi)
+{
+ unsigned long val;
+
+ wmb();
+
+ val = spi_tegra_readl(tspi, SLINK_DMA_CTL);
+ val &= ~SLINK_DMA_BLOCK_SIZE(~0) & ~SLINK_DMA_EN;
+ val |= SLINK_DMA_BLOCK_SIZE(tspi->rx_dma_req.size / 4 - 1);
+ spi_tegra_writel(tspi, val, SLINK_DMA_CTL);
+
+ tegra_dma_enqueue_req(tspi->rx_dma, &tspi->rx_dma_req);
+
+ val |= SLINK_DMA_EN;
+ spi_tegra_writel(tspi, val, SLINK_DMA_CTL);
+}
+
+static unsigned spi_tegra_fill_tx_fifo(struct spi_tegra_data *tspi,
+ struct spi_transfer *t)
+{
+ unsigned len = min(t->len - tspi->cur_pos, BB_LEN *
+ tspi->cur_bytes_per_word);
+ u8 *tx_buf = (u8 *)t->tx_buf + tspi->cur_pos;
+ int i, j;
+ unsigned long val;
+
+ val = spi_tegra_readl(tspi, SLINK_COMMAND);
+ val &= ~SLINK_WORD_SIZE(~0);
+ val |= SLINK_WORD_SIZE(len / tspi->cur_bytes_per_word - 1);
+ spi_tegra_writel(tspi, val, SLINK_COMMAND);
+
+ for (i = 0; i < len; i += tspi->cur_bytes_per_word) {
+ val = 0;
+ for (j = 0; j < tspi->cur_bytes_per_word; j++)
+ val |= tx_buf[i + j] << j * 8;
+
+ spi_tegra_writel(tspi, val, SLINK_TX_FIFO);
+ }
+
+ tspi->rx_dma_req.size = len / tspi->cur_bytes_per_word * 4;
+
+ return len;
+}
+
+static unsigned spi_tegra_drain_rx_fifo(struct spi_tegra_data *tspi,
+ struct spi_transfer *t)
+{
+ unsigned len = tspi->cur_len;
+ u8 *rx_buf = (u8 *)t->rx_buf + tspi->cur_pos;
+ int i, j;
+ unsigned long val;
+
+ for (i = 0; i < len; i += tspi->cur_bytes_per_word) {
+ val = tspi->rx_bb[i / tspi->cur_bytes_per_word];
+ for (j = 0; j < tspi->cur_bytes_per_word; j++)
+ rx_buf[i + j] = (val >> (j * 8)) & 0xff;
+ }
+
+ return len;
+}
+
+static void spi_tegra_start_transfer(struct spi_device *spi,
+ struct spi_transfer *t)
+{
+ struct spi_tegra_data *tspi = spi_master_get_devdata(spi->master);
+ u32 speed;
+ u8 bits_per_word;
+ unsigned long val;
+
+ speed = t->speed_hz ? t->speed_hz : spi->max_speed_hz;
+ bits_per_word = t->bits_per_word ? t->bits_per_word :
+ spi->bits_per_word;
+
+ tspi->cur_bytes_per_word = (bits_per_word - 1) / 8 + 1;
+
+ if (speed != tspi->cur_speed)
+ clk_set_rate(tspi->clk, speed);
+
+ if (tspi->cur_speed == 0)
+ clk_enable(tspi->clk);
+
+ tspi->cur_speed = speed;
+
+ val = spi_tegra_readl(tspi, SLINK_COMMAND2);
+ val &= ~SLINK_SS_EN_CS(~0) | SLINK_RXEN | SLINK_TXEN;
+ if (t->rx_buf)
+ val |= SLINK_RXEN;
+ if (t->tx_buf)
+ val |= SLINK_TXEN;
+ val |= SLINK_SS_EN_CS(spi->chip_select);
+ val |= SLINK_SPIE;
+ spi_tegra_writel(tspi, val, SLINK_COMMAND2);
+
+ val = spi_tegra_readl(tspi, SLINK_COMMAND);
+ val &= ~SLINK_BIT_LENGTH(~0);
+ val |= SLINK_BIT_LENGTH(bits_per_word - 1);
+
+ /* FIXME: should probably control CS manually so that we can be sure
+ * it does not go low between transfer and to support delay_usecs
+ * correctly.
+ */
+ val &= ~SLINK_IDLE_SCLK_MASK & ~SLINK_CK_SDA & ~SLINK_CS_SW;
+
+ if (spi->mode & SPI_CPHA)
+ val |= SLINK_CK_SDA;
+
+ if (spi->mode & SPI_CPOL)
+ val |= SLINK_IDLE_SCLK_DRIVE_HIGH;
+ else
+ val |= SLINK_IDLE_SCLK_DRIVE_LOW;
+
+ val |= SLINK_M_S;
+
+ spi_tegra_writel(tspi, val, SLINK_COMMAND);
+
+ spi_tegra_writel(tspi, SLINK_RX_FLUSH | SLINK_TX_FLUSH, SLINK_STATUS);
+
+ tspi->cur = t;
+ tspi->cur_pos = 0;
+ tspi->cur_len = spi_tegra_fill_tx_fifo(tspi, t);
+
+ spi_tegra_go(tspi);
+}
+
+static void spi_tegra_start_message(struct spi_device *spi,
+ struct spi_message *m)
+{
+ struct spi_transfer *t;
+
+ m->actual_length = 0;
+ m->status = 0;
+
+ t = list_first_entry(&m->transfers, struct spi_transfer, transfer_list);
+ spi_tegra_start_transfer(spi, t);
+}
+
+static void tegra_spi_rx_dma_complete(struct tegra_dma_req *req)
+{
+ struct spi_tegra_data *tspi = req->dev;
+ unsigned long flags;
+ struct spi_message *m;
+ struct spi_device *spi;
+ int timeout = 0;
+ unsigned long val;
+
+ /* the SPI controller may come back with both the BSY and RDY bits
+ * set. In this case we need to wait for the BSY bit to clear so
+ * that we are sure the DMA is finished. 1000 reads was empirically
+ * determined to be long enough.
+ */
+ while (timeout++ < 1000) {
+ if (!(spi_tegra_readl(tspi, SLINK_STATUS) & SLINK_BSY))
+ break;
+ }
+
+ spin_lock_irqsave(&tspi->lock, flags);
+
+ if (timeout >= 1000)
+ m->status = -EIO;
+
+ val = spi_tegra_readl(tspi, SLINK_STATUS);
+ val |= SLINK_RDY;
+ spi_tegra_writel(tspi, val, SLINK_STATUS);
+
+
+ m = list_first_entry(&tspi->queue, struct spi_message, queue);
+ spi = m->state;
+
+ tspi->cur_pos += spi_tegra_drain_rx_fifo(tspi, tspi->cur);
+ m->actual_length += tspi->cur_pos;
+
+ if (tspi->cur_pos < tspi->cur->len) {
+ tspi->cur_len = spi_tegra_fill_tx_fifo(tspi, tspi->cur);
+ spi_tegra_go(tspi);
+ } else if (!list_is_last(&tspi->cur->transfer_list,
+ &m->transfers)) {
+ tspi->cur = list_first_entry(&tspi->cur->transfer_list,
+ struct spi_transfer,
+ transfer_list);
+ spi_tegra_start_transfer(spi, tspi->cur);
+ } else {
+ list_del(&m->queue);
+
+ m->complete(m->context);
+
+ if (!list_empty(&tspi->queue)) {
+ m = list_first_entry(&tspi->queue, struct spi_message,
+ queue);
+ spi = m->state;
+ spi_tegra_start_message(spi, m);
+ } else {
+ clk_disable(tspi->clk);
+ tspi->cur_speed = 0;
+ }
+ }
+
+ spin_unlock_irqrestore(&tspi->lock, flags);
+}
+
+static int spi_tegra_setup(struct spi_device *spi)
+{
+ struct spi_tegra_data *tspi = spi_master_get_devdata(spi->master);
+ unsigned long cs_bit;
+ unsigned long val;
+ unsigned long flags;
+
+ dev_dbg(&spi->dev, "setup %d bpw, %scpol, %scpha, %dHz\n",
+ spi->bits_per_word,
+ spi->mode & SPI_CPOL ? "" : "~",
+ spi->mode & SPI_CPHA ? "" : "~",
+ spi->max_speed_hz);
+
+
+ switch (spi->chip_select) {
+ case 0:
+ cs_bit = SLINK_CS_POLARITY;
+ break;
+
+ case 1:
+ cs_bit = SLINK_CS_POLARITY1;
+ break;
+
+ case 2:
+ cs_bit = SLINK_CS_POLARITY2;
+ break;
+
+ case 4:
+ cs_bit = SLINK_CS_POLARITY3;
+ break;
+
+ default:
+ return -EINVAL;
+ }
+
+ spin_lock_irqsave(&tspi->lock, flags);
+
+ val = spi_tegra_readl(tspi, SLINK_COMMAND);
+ if (spi->mode & SPI_CS_HIGH)
+ val |= cs_bit;
+ else
+ val &= ~cs_bit;
+ spi_tegra_writel(tspi, val, SLINK_COMMAND);
+
+ spin_unlock_irqrestore(&tspi->lock, flags);
+
+ return 0;
+}
+
+static int spi_tegra_transfer(struct spi_device *spi, struct spi_message *m)
+{
+ struct spi_tegra_data *tspi = spi_master_get_devdata(spi->master);
+ struct spi_transfer *t;
+ unsigned long flags;
+ int was_empty;
+
+ if (list_empty(&m->transfers) || !m->complete)
+ return -EINVAL;
+
+ list_for_each_entry(t, &m->transfers, transfer_list) {
+ if (t->bits_per_word < 0 || t->bits_per_word > 32)
+ return -EINVAL;
+
+ if (t->len == 0)
+ return -EINVAL;
+
+ if (!t->rx_buf && !t->tx_buf)
+ return -EINVAL;
+ }
+
+ m->state = spi;
+
+ spin_lock_irqsave(&tspi->lock, flags);
+ was_empty = list_empty(&tspi->queue);
+ list_add_tail(&m->queue, &tspi->queue);
+
+ if (was_empty)
+ spi_tegra_start_message(spi, m);
+
+ spin_unlock_irqrestore(&tspi->lock, flags);
+
+ return 0;
+}
+
+static void spi_tegra_cleanup(struct spi_device *spi)
+{
+ dev_dbg(&spi->dev, "cleanup\n");
+}
+
+static int __init spi_tegra_probe(struct platform_device *pdev)
+{
+ struct spi_master *master;
+ struct spi_tegra_data *tspi;
+ struct resource *r;
+ int ret;
+
+ master = spi_alloc_master(&pdev->dev, sizeof *tspi);
+ if (master == NULL) {
+ dev_err(&pdev->dev, "master allocation failed\n");
+ return -ENOMEM;
+ }
+
+ /* the spi->mode bits understood by this driver: */
+ master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
+
+ if (pdev->id != -1)
+ master->bus_num = pdev->id;
+
+ master->setup = spi_tegra_setup;
+ master->transfer = spi_tegra_transfer;
+ master->cleanup = spi_tegra_cleanup;
+ master->num_chipselect = 4;
+
+ dev_set_drvdata(&pdev->dev, master);
+ tspi = spi_master_get_devdata(master);
+ tspi->master = master;
+ tspi->pdev = pdev;
+ spin_lock_init(&tspi->lock);
+
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (r == NULL) {
+ ret = -ENODEV;
+ goto err0;
+ }
+
+ if (!request_mem_region(r->start, (r->end - r->start) + 1,
+ dev_name(&pdev->dev))) {
+ ret = -EBUSY;
+ goto err0;
+ }
+
+ tspi->phys = r->start;
+ tspi->base = ioremap(r->start, r->end - r->start + 1);
+ if (!tspi->base) {
+ dev_err(&pdev->dev, "can't ioremap iomem\n");
+ ret = -ENOMEM;
+ goto err1;
+ }
+
+ tspi->clk = clk_get(&pdev->dev, NULL);
+ if (IS_ERR_OR_NULL(tspi->clk)) {
+ dev_err(&pdev->dev, "can not get clock\n");
+ ret = PTR_ERR(tspi->clk);
+ goto err2;
+ }
+
+ INIT_LIST_HEAD(&tspi->queue);
+
+ tspi->rx_dma = tegra_dma_allocate_channel(TEGRA_DMA_MODE_ONESHOT);
+ if (IS_ERR(tspi->rx_dma)) {
+ dev_err(&pdev->dev, "can not allocate rx dma channel\n");
+ ret = PTR_ERR(tspi->rx_dma);
+ goto err3;
+ }
+
+ tspi->rx_bb = dma_alloc_coherent(&pdev->dev, sizeof(u32) * BB_LEN,
+ &tspi->rx_bb_phys, GFP_KERNEL);
+ if (!tspi->rx_bb) {
+ dev_err(&pdev->dev, "can not allocate rx bounce buffer\n");
+ ret = -ENOMEM;
+ goto err4;
+ }
+
+ tspi->rx_dma_req.complete = tegra_spi_rx_dma_complete;
+ tspi->rx_dma_req.to_memory = 1;
+ tspi->rx_dma_req.dest_addr = tspi->rx_bb_phys;
+ tspi->rx_dma_req.dest_bus_width = 32;
+ tspi->rx_dma_req.source_addr = tspi->phys + SLINK_RX_FIFO;
+ tspi->rx_dma_req.source_bus_width = 32;
+ tspi->rx_dma_req.source_wrap = 4;
+ tspi->rx_dma_req.req_sel = spi_tegra_req_sels[pdev->id];
+ tspi->rx_dma_req.dev = tspi;
+
+ ret = spi_register_master(master);
+
+ if (ret < 0)
+ goto err5;
+
+ return ret;
+
+err5:
+ dma_free_coherent(&pdev->dev, sizeof(u32) * BB_LEN,
+ tspi->rx_bb, tspi->rx_bb_phys);
+err4:
+ tegra_dma_free_channel(tspi->rx_dma);
+err3:
+ clk_put(tspi->clk);
+err2:
+ iounmap(tspi->base);
+err1:
+ release_mem_region(r->start, (r->end - r->start) + 1);
+err0:
+ spi_master_put(master);
+ return ret;
+}
+
+static int __devexit spi_tegra_remove(struct platform_device *pdev)
+{
+ struct spi_master *master;
+ struct spi_tegra_data *tspi;
+ struct resource *r;
+
+ master = dev_get_drvdata(&pdev->dev);
+ tspi = spi_master_get_devdata(master);
+
+ tegra_dma_free_channel(tspi->rx_dma);
+
+ dma_free_coherent(&pdev->dev, sizeof(u32) * BB_LEN,
+ tspi->rx_bb, tspi->rx_bb_phys);
+
+ clk_put(tspi->clk);
+ iounmap(tspi->base);
+
+ spi_master_put(master);
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ release_mem_region(r->start, (r->end - r->start) + 1);
+
+ return 0;
+}
+
+MODULE_ALIAS("platform:spi_tegra");
+
+static struct platform_driver spi_tegra_driver = {
+ .driver = {
+ .name = "spi_tegra",
+ .owner = THIS_MODULE,
+ },
+ .remove = __devexit_p(spi_tegra_remove),
+};
+
+static int __init spi_tegra_init(void)
+{
+ return platform_driver_probe(&spi_tegra_driver, spi_tegra_probe);
+}
+module_init(spi_tegra_init);
+
+static void __exit spi_tegra_exit(void)
+{
+ platform_driver_unregister(&spi_tegra_driver);
+}
+module_exit(spi_tegra_exit);
+
+MODULE_LICENSE("GPL");
--
1.6.5.6
------------------------------------------------------------------------------
Sell apps to millions through the Intel(R) Atom(Tm) Developer Program
Be part of this innovative community and reach millions of netbook users
worldwide. Take advantage of special opportunities to increase revenue and
speed time-to-market. Join now, and jumpstart your future.
http://p.sf.net/sfu/intel-atom-d2d
next prev parent reply other threads:[~2010-08-25 21:23 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-07-30 0:37 [PATCH] spi: add spi_tegra driver Colin Cross
2010-07-30 7:54 ` Thierry Reding
[not found] ` <20100730075443.GA17814-RM9K5IK7kjKj5M59NBduVrNAH6kLmebB@public.gmane.org>
2010-08-02 18:48 ` Erik Gilling
2010-08-01 6:21 ` Grant Likely
[not found] ` <AANLkTimUm_wj+gyxTa=X+845kLj1sZ9GF+jsmsBwxnLN-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2010-08-12 0:31 ` Erik Gilling
2010-08-12 15:24 ` Russell King - ARM Linux
[not found] ` <20100812152424.GB31982-l+eeeJia6m9vn6HldHNs0ANdhmdF6hFW@public.gmane.org>
2010-08-12 18:44 ` Erik Gilling
[not found] ` <1280450224-25118-1-git-send-email-ccross-hpIqsD4AKlfQT0dZR+AlfA@public.gmane.org>
2010-08-12 0:47 ` [PATCH v2] " Erik Gilling
[not found] ` <1281574023-25160-1-git-send-email-konkers-z5hGa2qSFaRBDgjK7y7TUQ@public.gmane.org>
2010-08-12 19:54 ` Grant Likely
[not found] ` <AANLkTim4nL+Re=qc55CGS+ksq+ACtGe=vqOeGQ3HbQWM-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2010-08-25 21:22 ` Erik Gilling
[not found] ` <AANLkTincgapUK5ncs_t3ax=1Kt_56GdR_RVwRqdCm5ge-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2010-08-27 19:26 ` Erik Gilling
[not found] ` <AANLkTin4HxVLt=4VH-NQWhB-p_2EpX_yoTcwEOTJP3m_-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2010-08-27 20:13 ` Grant Likely
2010-08-25 21:23 ` Erik Gilling [this message]
2010-09-01 22:16 ` [PATCH v4] " Erik Gilling
2010-09-01 22:18 ` Erik Gilling
2010-09-02 14:22 ` Grant Likely
[not found] ` <AANLkTimonLa1mUVSHR=QnR48HPtAZ5BW3BsVsg7MWALy-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2010-10-10 6:31 ` Grant Likely
[not found] ` <AANLkTini_PA3J+R4gEP4DzFpcAxHhdmDbcXxOtj2h81O-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2010-10-11 21:01 ` Erik Gilling
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1282771395-21684-1-git-send-email-konkers@android.com \
--to=konkers-z5hga2qsfarbdgjk7y7tuq@public.gmane.org \
--cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=linux-lFZ/pmaqli7XmaaqVzeoHQ@public.gmane.org \
--cc=linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).