From: Cyril Chemparathy <cyril-l0cyMroinI0@public.gmane.org>
To: davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/@public.gmane.org,
spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org,
broonie-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org,
lrg-kDsPt+C1G03kYMGBc/C6ZA@public.gmane.org,
dbrownell-Rn4VEauK+AKRv+LV9MX5uipxlwaOVQ5f@public.gmane.org, gra
Cc: Cyril Chemparathy <cyril-l0cyMroinI0@public.gmane.org>
Subject: [PATCH v4 03/12] davinci: add ssp config for tnetv107x evm board
Date: Tue, 26 Oct 2010 16:18:19 -0400 [thread overview]
Message-ID: <1288124308-14999-4-git-send-email-cyril@ti.com> (raw)
In-Reply-To: <1288124308-14999-1-git-send-email-cyril-l0cyMroinI0@public.gmane.org>
This patch adds SSP configuration and pin muxing info for tnetv107x
evm boards.
Signed-off-by: Cyril Chemparathy <cyril-l0cyMroinI0@public.gmane.org>
---
arch/arm/mach-davinci/board-tnetv107x-evm.c | 15 +++++++++++++++
1 files changed, 15 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-davinci/board-tnetv107x-evm.c b/arch/arm/mach-davinci/board-tnetv107x-evm.c
index a6db854..c74ea66 100644
--- a/arch/arm/mach-davinci/board-tnetv107x-evm.c
+++ b/arch/arm/mach-davinci/board-tnetv107x-evm.c
@@ -33,6 +33,7 @@
#include <mach/edma.h>
#include <mach/mux.h>
#include <mach/cp_intc.h>
+#include <mach/ti_ssp.h>
#include <mach/tnetv107x.h>
#define EVM_MMC_WP_GPIO 21
@@ -99,6 +100,12 @@ static const short uart1_pins[] __initdata = {
-1
};
+static const short ssp_pins[] __initdata = {
+ TNETV107X_SSP0_0, TNETV107X_SSP0_1, TNETV107X_SSP0_2,
+ TNETV107X_SSP1_0, TNETV107X_SSP1_1, TNETV107X_SSP1_2,
+ TNETV107X_SSP1_3, -1
+};
+
static struct mtd_partition nand_partitions[] = {
/* bootloader (U-Boot, etc) in first 12 sectors */
{
@@ -196,17 +203,25 @@ static struct matrix_keypad_platform_data keypad_config = {
.no_autorepeat = 0,
};
+static struct ti_ssp_data ssp_config = {
+ .out_clock = 250 * 1000,
+ .dev_data = {
+ },
+};
+
static struct tnetv107x_device_info evm_device_info __initconst = {
.serial_config = &serial_config,
.mmc_config[1] = &mmc_config, /* controller 1 */
.nand_config[0] = &nand_config, /* chip select 0 */
.keypad_config = &keypad_config,
+ .ssp_config = &ssp_config,
};
static __init void tnetv107x_evm_board_init(void)
{
davinci_cfg_reg_list(sdio1_pins);
davinci_cfg_reg_list(uart1_pins);
+ davinci_cfg_reg_list(ssp_pins);
tnetv107x_devices_init(&evm_device_info);
}
--
1.7.0.4
------------------------------------------------------------------------------
Nokia and AT&T present the 2010 Calling All Innovators-North America contest
Create new apps & games for the Nokia N8 for consumers in U.S. and Canada
$10 million total in prizes - $4M cash, 500 devices, nearly $6M in marketing
Develop with Nokia Qt SDK, Web Runtime, or Java and Publish to Ovi Store
http://p.sf.net/sfu/nokia-dev2dev
next prev parent reply other threads:[~2010-10-26 20:18 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-10-26 20:18 [PATCH v4 00/12] tnetv107x ssp driver stack Cyril Chemparathy
[not found] ` <1288124308-14999-1-git-send-email-cyril-l0cyMroinI0@public.gmane.org>
2010-10-26 20:18 ` [PATCH v4 01/12] misc: add driver for sequencer serial port Cyril Chemparathy
2010-10-28 15:49 ` Linus Walleij
[not found] ` <AANLkTi=rDep3jkp2QAjVsgjZ7JQ0ysnse4TARv29fyHm-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2010-10-28 16:09 ` Cyril Chemparathy
2010-10-28 18:14 ` Linus Walleij
2010-10-26 20:18 ` [PATCH v4 02/12] davinci: add tnetv107x ssp platform device Cyril Chemparathy
2010-10-26 20:18 ` Cyril Chemparathy [this message]
2010-10-26 20:18 ` [PATCH v4 04/12] spi: add ti-ssp spi master driver Cyril Chemparathy
2010-10-26 20:18 ` [PATCH v4 05/12] davinci: add spi devices on tnetv107x evm Cyril Chemparathy
2010-10-26 20:18 ` [PATCH v4 06/12] regulator: add driver for tps6524x regulator Cyril Chemparathy
2010-10-26 20:18 ` [PATCH v4 07/12] davinci: add tnetv107x evm regulators Cyril Chemparathy
2010-10-26 20:18 ` [PATCH v4 08/12] gpio: add ti-ssp gpio driver Cyril Chemparathy
[not found] ` <1288124308-14999-9-git-send-email-cyril-l0cyMroinI0@public.gmane.org>
2010-11-03 2:15 ` David Brownell
2010-11-03 10:18 ` Linus Walleij
[not found] ` <AANLkTin=3K0H+YdNM2Nhz63c3+Upp+rwApo-Ww4p5qH6-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2010-11-03 12:35 ` David Brownell
2010-11-03 16:24 ` Linus Walleij
2010-11-10 4:45 ` Grant Likely
[not found] ` <20101110044530.GB4110-MrY2KI0G/OVr83L8+7iqerDks+cytr/Z@public.gmane.org>
2010-11-10 6:16 ` David Brownell
2010-11-10 6:23 ` Grant Likely
[not found] ` <20101110062310.GB7431-MrY2KI0G/OVr83L8+7iqerDks+cytr/Z@public.gmane.org>
2010-11-10 14:34 ` Cyril Chemparathy
2010-10-26 20:18 ` [PATCH v4 09/12] davinci: add tnetv107x evm ti-ssp gpio device Cyril Chemparathy
2010-10-26 20:18 ` [PATCH v4 10/12] backlight: add support for tps6116x controller Cyril Chemparathy
2010-10-26 20:18 ` [PATCH v4 11/12] davinci: add tnetv107x evm backlight device Cyril Chemparathy
2010-10-26 20:18 ` [PATCH v4 12/12] davinci: add tnetv107x evm i2c eeprom device Cyril Chemparathy
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1288124308-14999-4-git-send-email-cyril@ti.com \
--to=cyril-l0cymroini0@public.gmane.org \
--cc=broonie-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org \
--cc=davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/@public.gmane.org \
--cc=dbrownell-Rn4VEauK+AKRv+LV9MX5uipxlwaOVQ5f@public.gmane.org \
--cc=lrg-kDsPt+C1G03kYMGBc/C6ZA@public.gmane.org \
--cc=spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).