* [PATCH RESEND] SPI: McSPI: allow configuration of pin directions
@ 2012-10-11 12:18 Daniel Mack
0 siblings, 0 replies; only message in thread
From: Daniel Mack @ 2012-10-11 12:18 UTC (permalink / raw)
To: spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f
Cc: Juha Yrjola, Samuel Ortiz, linus.walleij-QSEj5FYQhm4dnm+yROfE0A,
broonie-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E,
rob.herring-bsGFqQB8/DxBDgjK7y7TUQ, Daniel Mack, Matus Ujhelyi,
Vaibhav Hiremath, Shubhrajyoti D
Allow D0 to be an input and D1 to be an output, configurable via
platform data and a new DT property.
Based on a patch from Matus Ujhelyi <matus.ujhelyi-6oiIBCxl0MMjD8S081q9vkEOCMrvLtNR@public.gmane.org>
Signed-off-by: Daniel Mack <zonque-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
Cc: Matus Ujhelyi <matus.ujhelyi-6oiIBCxl0MMjD8S081q9vkEOCMrvLtNR@public.gmane.org>
Cc: Mark Brown <broonie-yzvPICuk2AATkU/dhu1WVueM+bqZidxxQQ4Iyu8u01E@public.gmane.org>
Cc: Grant Likely <grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org>
Cc: Linus Walleij <linus.walleij-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Cc: Samuel Ortiz <sameo-VuQAYsv1563Yd54FQh9/CA@public.gmane.org>
Cc: Juha Yrjola <juha.yrjola-EmnPodGKVbzby3iVrkZq2A@public.gmane.org>
Cc: Vaibhav Hiremath <hvaibhav-l0cyMroinI0@public.gmane.org>
Cc: Shubhrajyoti D <shubhrajyoti-l0cyMroinI0@public.gmane.org>
---
Resending with more people in cc
Documentation/devicetree/bindings/spi/omap-spi.txt | 4 +++-
drivers/spi/spi-omap2-mcspi.c | 25 ++++++++++++++++------
include/linux/platform_data/spi-omap2-mcspi.h | 4 ++++
3 files changed, 25 insertions(+), 8 deletions(-)
diff --git a/Documentation/devicetree/bindings/spi/omap-spi.txt b/Documentation/devicetree/bindings/spi/omap-spi.txt
index 81df374..2ef0a6b 100644
--- a/Documentation/devicetree/bindings/spi/omap-spi.txt
+++ b/Documentation/devicetree/bindings/spi/omap-spi.txt
@@ -6,7 +6,9 @@ Required properties:
- "ti,omap4-spi" for OMAP4+.
- ti,spi-num-cs : Number of chipselect supported by the instance.
- ti,hwmods: Name of the hwmod associated to the McSPI
-
+- ti,pindir-d0-in-d1-out: Select the D0 pin as input and D1 as
+ output. The default is D0 as output and
+ D1 as input.
Example:
diff --git a/drivers/spi/spi-omap2-mcspi.c b/drivers/spi/spi-omap2-mcspi.c
index 3542fdc..5104633 100644
--- a/drivers/spi/spi-omap2-mcspi.c
+++ b/drivers/spi/spi-omap2-mcspi.c
@@ -130,6 +130,7 @@ struct omap2_mcspi {
struct omap2_mcspi_dma *dma_channels;
struct device *dev;
struct omap2_mcspi_regs ctx;
+ unsigned int pin_dir:1;
};
struct omap2_mcspi_cs {
@@ -765,8 +766,15 @@ static int omap2_mcspi_setup_transfer(struct spi_device *spi,
/* standard 4-wire master mode: SCK, MOSI/out, MISO/in, nCS
* REVISIT: this controller could support SPI_3WIRE mode.
*/
- l &= ~(OMAP2_MCSPI_CHCONF_IS|OMAP2_MCSPI_CHCONF_DPE1);
- l |= OMAP2_MCSPI_CHCONF_DPE0;
+ if (mcspi->pin_dir == MCSPI_PINDIR_D0_OUT_D1_IN) {
+ l &= ~OMAP2_MCSPI_CHCONF_IS;
+ l &= ~OMAP2_MCSPI_CHCONF_DPE1;
+ l |= OMAP2_MCSPI_CHCONF_DPE0;
+ } else {
+ l |= OMAP2_MCSPI_CHCONF_IS;
+ l |= OMAP2_MCSPI_CHCONF_DPE1;
+ l &= ~OMAP2_MCSPI_CHCONF_DPE0;
+ }
/* wordlength */
l &= ~OMAP2_MCSPI_CHCONF_WL_MASK;
@@ -1167,6 +1175,11 @@ static int __devinit omap2_mcspi_probe(struct platform_device *pdev)
master->cleanup = omap2_mcspi_cleanup;
master->dev.of_node = node;
+ dev_set_drvdata(&pdev->dev, master);
+
+ mcspi = spi_master_get_devdata(master);
+ mcspi->master = master;
+
match = of_match_device(omap_mcspi_of_match, &pdev->dev);
if (match) {
u32 num_cs = 1; /* default number of chipselect */
@@ -1175,19 +1188,17 @@ static int __devinit omap2_mcspi_probe(struct platform_device *pdev)
of_property_read_u32(node, "ti,spi-num-cs", &num_cs);
master->num_chipselect = num_cs;
master->bus_num = bus_num++;
+ if (of_get_property(node, "ti,pindir-d0-in-d1-out", NULL))
+ mcspi->pin_dir = MCSPI_PINDIR_D0_IN_D1_OUT;
} else {
pdata = pdev->dev.platform_data;
master->num_chipselect = pdata->num_cs;
if (pdev->id != -1)
master->bus_num = pdev->id;
+ mcspi->pin_dir = pdata->pin_dir;
}
regs_offset = pdata->regs_offset;
- dev_set_drvdata(&pdev->dev, master);
-
- mcspi = spi_master_get_devdata(master);
- mcspi->master = master;
-
r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (r == NULL) {
status = -ENODEV;
diff --git a/include/linux/platform_data/spi-omap2-mcspi.h b/include/linux/platform_data/spi-omap2-mcspi.h
index a357eb2..ce70f7b 100644
--- a/include/linux/platform_data/spi-omap2-mcspi.h
+++ b/include/linux/platform_data/spi-omap2-mcspi.h
@@ -7,9 +7,13 @@
#define OMAP4_MCSPI_REG_OFFSET 0x100
+#define MCSPI_PINDIR_D0_OUT_D1_IN 0
+#define MCSPI_PINDIR_D0_IN_D1_OUT 1
+
struct omap2_mcspi_platform_config {
unsigned short num_cs;
unsigned int regs_offset;
+ unsigned int pin_dir:1;
};
struct omap2_mcspi_dev_attr {
--
1.7.11.4
------------------------------------------------------------------------------
Don't let slow site performance ruin your business. Deploy New Relic APM
Deploy New Relic app performance management and know exactly
what is happening inside your Ruby, Python, PHP, Java, and .NET app
Try New Relic at no cost today and get our sweet Data Nerd shirt too!
http://p.sf.net/sfu/newrelic-dev2dev
^ permalink raw reply related [flat|nested] only message in thread
only message in thread, other threads:[~2012-10-11 12:18 UTC | newest]
Thread overview: (only message) (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2012-10-11 12:18 [PATCH RESEND] SPI: McSPI: allow configuration of pin directions Daniel Mack
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).