[PATCH 00/15] ARM: shmobile: RSPI RZ and QSPI SoC and board integration

[PATCH 00/15] ARM: shmobile: RSPI RZ and QSPI SoC and board integration

[Geert Uytterhoeven]

	Hi Simon, Magnus,

This patch series contains SoC and board integration for
  1. RSPI in the r7s72100 aka RZ/A1H SoC on the Genmai reference board,
  2. QSPI in the r8a7791 aka R-Car M2 SoC on the Koelsch reference board.

It was tested on the r7s72100-based Genmai reference board using loopback
mode, and on the r8a7791-based Koelsch reference board using the Spansion
s25fl512s SPI FLASH.

Actual functioning for some parts may depend on the series "[PATCH 0/14]
spi: rspi: Add support for RZ/A1H, DT, and Quad/Dual on QSPI" I posted
earlier today.

Overview:
    [v4 01/15] ARM: shmobile: r7s72100 clock: Add RSPI clocks
    [v4 02/15] ARM: shmobile: genmai legacy: Add RSPI support
    [v4 03/15] [WIP] ARM: shmobile: genmai legacy: Add preliminary RSPI
	       pinmux setup
    [v2 04/15] ARM: shmobile: genmai defconfig: Enable RSPI
    [v2 05/15] ARM: shmobile: r7s72100 clock: Add RSPI clocks for DT
    [v4 06/15] ARM: shmobile: r7s72100 dtsi: Add RSPI nodes
    [v4 07/15] ARM: shmobile: genmai reference dts: Add RSPI nodes
    [v3 08/15] ARM: shmobile: r8a7791 clock: add QSPI clocks
    [v3 09/15] ARM: shmobile: koelsch legacy: Add QSPI support
    [v3 10/15] ARM: shmobile: koelsch defconfig: Enable RSPI and MTD_M25P80
    [v2 11/15] ARM: shmobile: r8a7791 dtsi: Add QSPI node
    [v2 12/15] ARM: shmobile: koelsch dts: Add QSPI nodes
    [   13/15] ARM: shmobile: lager legacy: Switch QSPI to named IRQs
    [   14/15] ARM: shmobile: koelsch legacy: Enable Quad SPI transfers for
	       the SPI FLASH
    [   15/15] ARM: shmobile: koelsch dts: Enable Quad SPI transfers

Earlier versions of these have been posted before in:
    "[PATCH V3 0/5] SoC and board integration for RSPI on r7s72100/genmai"
    "[PATCH V2 0/4] SoC and board integration for QSPI on r8a7791/koelsch"
    "[PATCH 0/9] Renesas RSPI/QSPI DT support"

The series is based on renesas-devel-v3.13-20140124, with pinctrl work 
accepted by Linus, Magnus' pinctrl, Wolfram's riic, Simon's sh_eth,
Valentine's i2c, and Laurent's SCIF DT work applied on top.
[Simon: I don't know in which order you will merge these. If you want me
 to rebase my patches, just ask! Thanks!]

All of these should be safe to apply, without runtime dependencies on other
parts, except for [14/15] and [15/15]: those must not go in before
"[14/14] spi: rspi: Add support for Quad and Dual SPI Transfers on QSPI",
as this would disable SPI FLASH access (the SPI core rejects Quad SPI slaves
without Quad SPI master support).

Thanks!

Gr{oetje,eeting}s,

						Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert-Td1EMuHUCqxL1ZNQvxDV9g@public.gmane.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
							    -- Linus Torvalds
--
To unsubscribe from this list: send the line "unsubscribe linux-spi" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v4 01/15] ARM: shmobile: r7s72100 clock: Add RSPI clocks

[Geert Uytterhoeven]

From: Geert Uytterhoeven <geert+renesas@linux-m68k.org>

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
---
v4:
  - The platform device basename was changed from "rspi" to "rspi-rz"
v3:
  - No changes
v2:
  - Correct platform device names ("rspi%u" -> "rspi.%u")

 arch/arm/mach-shmobile/clock-r7s72100.c |   21 ++++++++++++++++++---
 1 file changed, 18 insertions(+), 3 deletions(-)

diff --git a/arch/arm/mach-shmobile/clock-r7s72100.c b/arch/arm/mach-shmobile/clock-r7s72100.c
index 0242ca5f499a..bf15b63c3d5a 100644
--- a/arch/arm/mach-shmobile/clock-r7s72100.c
+++ b/arch/arm/mach-shmobile/clock-r7s72100.c
@@ -22,13 +22,15 @@
 #include <mach/common.h>
 #include <mach/r7s72100.h>
 
-/* registers */
+/* Frequency Control Registers */
 #define FRQCR		0xfcfe0010
 #define FRQCR2		0xfcfe0014
+/* Standby Control Registers */
 #define STBCR3		0xfcfe0420
 #define STBCR4		0xfcfe0424
 #define STBCR7		0xfcfe0430
 #define STBCR9		0xfcfe0438
+#define STBCR10		0xfcfe043c
 
 #define PLL_RATE 30
 
@@ -146,12 +148,20 @@ struct clk div4_clks[DIV4_NR] = {
 					| CLK_ENABLE_ON_INIT),
 };
 
-enum {	MSTP97, MSTP96, MSTP95, MSTP94,
+enum {
+	MSTP107, MSTP106, MSTP105, MSTP104, MSTP103,
+	MSTP97, MSTP96, MSTP95, MSTP94,
 	MSTP74,
 	MSTP47, MSTP46, MSTP45, MSTP44, MSTP43, MSTP42, MSTP41, MSTP40,
-	MSTP33,	MSTP_NR };
+	MSTP33,	MSTP_NR
+};
 
 static struct clk mstp_clks[MSTP_NR] = {
+	[MSTP107] = SH_CLK_MSTP8(&peripheral1_clk, STBCR10, 7, 0), /* RSPI0 */
+	[MSTP106] = SH_CLK_MSTP8(&peripheral1_clk, STBCR10, 6, 0), /* RSPI1 */
+	[MSTP105] = SH_CLK_MSTP8(&peripheral1_clk, STBCR10, 5, 0), /* RSPI2 */
+	[MSTP104] = SH_CLK_MSTP8(&peripheral1_clk, STBCR10, 4, 0), /* RSPI3 */
+	[MSTP103] = SH_CLK_MSTP8(&peripheral1_clk, STBCR10, 3, 0), /* RSPI4 */
 	[MSTP97] = SH_CLK_MSTP8(&peripheral0_clk, STBCR9, 7, 0), /* RIIC0 */
 	[MSTP96] = SH_CLK_MSTP8(&peripheral0_clk, STBCR9, 6, 0), /* RIIC1 */
 	[MSTP95] = SH_CLK_MSTP8(&peripheral0_clk, STBCR9, 5, 0), /* RIIC2 */
@@ -179,6 +189,11 @@ static struct clk_lookup lookups[] = {
 	CLKDEV_CON_ID("cpu_clk", &div4_clks[DIV4_I]),
 
 	/* MSTP clocks */
+	CLKDEV_DEV_ID("rspi-rz.0", &mstp_clks[MSTP107]),
+	CLKDEV_DEV_ID("rspi-rz.1", &mstp_clks[MSTP106]),
+	CLKDEV_DEV_ID("rspi-rz.2", &mstp_clks[MSTP105]),
+	CLKDEV_DEV_ID("rspi-rz.3", &mstp_clks[MSTP104]),
+	CLKDEV_DEV_ID("rspi-rz.4", &mstp_clks[MSTP103]),
 	CLKDEV_DEV_ID("fcfee000.i2c", &mstp_clks[MSTP97]),
 	CLKDEV_DEV_ID("fcfee400.i2c", &mstp_clks[MSTP96]),
 	CLKDEV_DEV_ID("fcfee800.i2c", &mstp_clks[MSTP95]),
-- 
1.7.9.5

[PATCH v4 02/15] ARM: shmobile: genmai legacy: Add RSPI support

[Geert Uytterhoeven]

From: Geert Uytterhoeven <geert+renesas@linux-m68k.org>

Add RSPI platform device, resources, platform data, and SPI child.

On this board, only rspi4 is in use. Its bus contains a single device
(a wm8978 audio codec).

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
---
v4:
  - The platform device basename was changed from "rspi" to "rspi-rz",
    dropping the platform data flags in the process
  - Switch to named IRQs
v3:
  - Move platform devices from setup-r7s72100.c to board-genmai.c, as
    genmai-reference will use devices instantiated from DT
  - Merge with "ARM: shmobile: genmai: Add RSPI children", as this now
    touches the same file
  - Instantiate SPI children in C on genmai only, as genmai-reference will
    instantiate them from DT
v2:
  - Correct platform device names ("rspi%u.0" -> "rspi.%u")
  - Add missing platform data
  - Correct summary (resources -> platform devices)

 arch/arm/mach-shmobile/board-genmai.c |   42 +++++++++++++++++++++++++++++++++
 1 file changed, 42 insertions(+)

diff --git a/arch/arm/mach-shmobile/board-genmai.c b/arch/arm/mach-shmobile/board-genmai.c
index a1f6fe1fb06f..0b01b7f7e240 100644
--- a/arch/arm/mach-shmobile/board-genmai.c
+++ b/arch/arm/mach-shmobile/board-genmai.c
@@ -21,6 +21,8 @@
 #include <linux/kernel.h>
 #include <linux/platform_device.h>
 #include <linux/sh_eth.h>
+#include <linux/spi/rspi.h>
+#include <linux/spi/spi.h>
 #include <mach/common.h>
 #include <mach/irqs.h>
 #include <mach/r7s72100.h>
@@ -41,11 +43,51 @@ static const struct resource ether_resources[] __initconst = {
 	DEFINE_RES_IRQ(gic_iid(359)),
 };
 
+/* RSPI */
+#define RSPI_RESOURCE(idx, baseaddr, irq)				\
+static const struct resource rspi##idx##_resources[] __initconst = {	\
+	DEFINE_RES_MEM(baseaddr, 0x24),					\
+	DEFINE_RES_IRQ_NAMED(irq, "error"),				\
+	DEFINE_RES_IRQ_NAMED(irq + 1, "rx"),				\
+	DEFINE_RES_IRQ_NAMED(irq + 2, "tx"),				\
+}
+
+RSPI_RESOURCE(0, 0xe800c800, gic_iid(270));
+RSPI_RESOURCE(1, 0xe800d000, gic_iid(273));
+RSPI_RESOURCE(2, 0xe800d800, gic_iid(276));
+RSPI_RESOURCE(3, 0xe800e000, gic_iid(279));
+RSPI_RESOURCE(4, 0xe800e800, gic_iid(282));
+
+static const struct rspi_plat_data rspi_pdata __initconst = {
+	.num_chipselect	= 1,
+};
+
+#define r7s72100_register_rspi(idx)					   \
+	platform_device_register_resndata(&platform_bus, "rspi-rz", idx,   \
+					rspi##idx##_resources,		   \
+					ARRAY_SIZE(rspi##idx##_resources), \
+					&rspi_pdata, sizeof(rspi_pdata))
+
+static const struct spi_board_info spi_info[] __initconst = {
+	{
+		.modalias               = "wm8978",
+		.max_speed_hz           = 5000000,
+		.bus_num                = 4,
+		.chip_select            = 0,
+	},
+};
+
 static void __init genmai_add_standard_devices(void)
 {
 	r7s72100_clock_init();
 	r7s72100_add_dt_devices();
 
+	r7s72100_register_rspi(0);
+	r7s72100_register_rspi(1);
+	r7s72100_register_rspi(2);
+	r7s72100_register_rspi(3);
+	r7s72100_register_rspi(4);
+	spi_register_board_info(spi_info, ARRAY_SIZE(spi_info));
 	platform_device_register_resndata(&platform_bus, "r7s72100-ether", -1,
 					  ether_resources,
 					  ARRAY_SIZE(ether_resources),
-- 
1.7.9.5

[PATCH v4 03/15] [WIP] ARM: shmobile: genmai legacy: Add preliminary RSPI pinmux setup

[Geert Uytterhoeven]

From: Geert Uytterhoeven <geert+renesas@linux-m68k.org>

This does not work yet, as there's no pinmux configuration in
setup-r7s72100.c

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
---
v4:
  - The platform device basename was changed from "rspi" to "rspi-rz"
v3:
  - No changes
v2:
  - New

 arch/arm/mach-shmobile/board-genmai.c |   17 +++++++++++++++++
 1 file changed, 17 insertions(+)

diff --git a/arch/arm/mach-shmobile/board-genmai.c b/arch/arm/mach-shmobile/board-genmai.c
index 0b01b7f7e240..3d02167967ec 100644
--- a/arch/arm/mach-shmobile/board-genmai.c
+++ b/arch/arm/mach-shmobile/board-genmai.c
@@ -19,6 +19,7 @@
  */
 
 #include <linux/kernel.h>
+#include <linux/pinctrl/machine.h>
 #include <linux/platform_device.h>
 #include <linux/sh_eth.h>
 #include <linux/spi/rspi.h>
@@ -77,9 +78,25 @@ static const struct spi_board_info spi_info[] __initconst = {
 	},
 };
 
+static const struct pinctrl_map genmai_pinctrl_map[] = {
+	/* RSPI4 */
+	PIN_MAP_MUX_GROUP_DEFAULT("rspi-rz.4", "pfc-r7s72100",
+				  "rspi4_rspck_p4_0", "rspi4"),
+	PIN_MAP_MUX_GROUP_DEFAULT("rspi-rz.4", "pfc-r7s72100",
+				  "rspi4_ssl0_p4_1", "rspi4"),
+	PIN_MAP_MUX_GROUP_DEFAULT("rspi-rz.4", "pfc-r7s72100",
+				  "rspi4_mosi_p4_2", "rspi4"),
+	PIN_MAP_MUX_GROUP_DEFAULT("rspi-rz.4", "pfc-r7s72100",
+				  "rspi4_miso_p4_3", "rspi4"),
+};
+
 static void __init genmai_add_standard_devices(void)
 {
 	r7s72100_clock_init();
+	pinctrl_register_mappings(genmai_pinctrl_map,
+				  ARRAY_SIZE(genmai_pinctrl_map));
+	/* FIXME there's no pinmux configuration in setup-r7s72100.c yet */
+	/* r7s72100_pinmux_init(); */
 	r7s72100_add_dt_devices();
 
 	r7s72100_register_rspi(0);
-- 
1.7.9.5

[PATCH v2 04/15] ARM: shmobile: genmai defconfig: Enable RSPI

[Geert Uytterhoeven]

From: Geert Uytterhoeven <geert+renesas-Td1EMuHUCqxL1ZNQvxDV9g@public.gmane.org>

Signed-off-by: Geert Uytterhoeven <geert+renesas-Td1EMuHUCqxL1ZNQvxDV9g@public.gmane.org>
---
v2:
  - No changes

 arch/arm/configs/genmai_defconfig |    2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm/configs/genmai_defconfig b/arch/arm/configs/genmai_defconfig
index ede35f400df2..401285305251 100644
--- a/arch/arm/configs/genmai_defconfig
+++ b/arch/arm/configs/genmai_defconfig
@@ -79,6 +79,8 @@ CONFIG_SERIAL_SH_SCI_NR_UARTS=10
 CONFIG_SERIAL_SH_SCI_CONSOLE=y
 # CONFIG_HW_RANDOM is not set
 CONFIG_I2C_SH_MOBILE=y
+CONFIG_SPI=y
+CONFIG_SPI_RSPI=y
 # CONFIG_HWMON is not set
 CONFIG_THERMAL=y
 CONFIG_RCAR_THERMAL=y
-- 
1.7.9.5

--
To unsubscribe from this list: send the line "unsubscribe linux-spi" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v2 05/15] ARM: shmobile: r7s72100 clock: Add RSPI clocks for DT

[Geert Uytterhoeven]

From: Geert Uytterhoeven <geert+renesas@linux-m68k.org>

Add DT-style ("%08x.spi") clocks, as Genmai doesn't use the common
clock framework yet.

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
---
v2:
  - No changes

 arch/arm/mach-shmobile/clock-r7s72100.c |    5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/mach-shmobile/clock-r7s72100.c b/arch/arm/mach-shmobile/clock-r7s72100.c
index bf15b63c3d5a..f17a5db00221 100644
--- a/arch/arm/mach-shmobile/clock-r7s72100.c
+++ b/arch/arm/mach-shmobile/clock-r7s72100.c
@@ -194,6 +194,11 @@ static struct clk_lookup lookups[] = {
 	CLKDEV_DEV_ID("rspi-rz.2", &mstp_clks[MSTP105]),
 	CLKDEV_DEV_ID("rspi-rz.3", &mstp_clks[MSTP104]),
 	CLKDEV_DEV_ID("rspi-rz.4", &mstp_clks[MSTP103]),
+	CLKDEV_DEV_ID("e800c800.spi", &mstp_clks[MSTP107]),
+	CLKDEV_DEV_ID("e800d000.spi", &mstp_clks[MSTP106]),
+	CLKDEV_DEV_ID("e800d800.spi", &mstp_clks[MSTP105]),
+	CLKDEV_DEV_ID("e800e000.spi", &mstp_clks[MSTP104]),
+	CLKDEV_DEV_ID("e800e800.spi", &mstp_clks[MSTP103]),
 	CLKDEV_DEV_ID("fcfee000.i2c", &mstp_clks[MSTP97]),
 	CLKDEV_DEV_ID("fcfee400.i2c", &mstp_clks[MSTP96]),
 	CLKDEV_DEV_ID("fcfee800.i2c", &mstp_clks[MSTP95]),
-- 
1.7.9.5

[PATCH v4 06/15] ARM: shmobile: r7s72100 dtsi: Add RSPI nodes

[Geert Uytterhoeven]

From: Geert Uytterhoeven <geert+renesas@linux-m68k.org>

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Cc: devicetree@vger.kernel.org
---
v4:
  - Switch to named IRQs
v3:
  - No changes
v2:
  - No changes

 arch/arm/boot/dts/r7s72100.dtsi |   70 +++++++++++++++++++++++++++++++++++++++
 1 file changed, 70 insertions(+)

diff --git a/arch/arm/boot/dts/r7s72100.dtsi b/arch/arm/boot/dts/r7s72100.dtsi
index ff0bd6be454f..d7013df6bb10 100644
--- a/arch/arm/boot/dts/r7s72100.dtsi
+++ b/arch/arm/boot/dts/r7s72100.dtsi
@@ -34,6 +34,11 @@
 		gpio10 = &port10;
 		gpio11 = &port11;
 		gpio12 = &jtagport0;
+		spi0 = &spi0;
+		spi1 = &spi1;
+		spi2 = &spi2;
+		spi3 = &spi3;
+		spi4 = &spi4;
 	};
 
 	cpus {
@@ -289,4 +294,69 @@
 		clock-frequency = <100000>;
 		status = "disabled";
 	};
+
+	spi0: spi@e800c800 {
+		compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz";
+		reg = <0xe800c800 0x24>;
+		interrupts = <0 238 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 239 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 240 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "error", "rx", "tx";
+		num-cs = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
+	spi1: spi@e800d000 {
+		compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz";
+		reg = <0xe800d000 0x24>;
+		interrupts = <0 241 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 242 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 243 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "error", "rx", "tx";
+		num-cs = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
+	spi2: spi@e800d800 {
+		compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz";
+		reg = <0xe800d800 0x24>;
+		interrupts = <0 244 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 245 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 246 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "error", "rx", "tx";
+		num-cs = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
+	spi3: spi@e800e000 {
+		compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz";
+		reg = <0xe800e000 0x24>;
+		interrupts = <0 247 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 248 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 249 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "error", "rx", "tx";
+		num-cs = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
+	spi4: spi@e800e800 {
+		compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz";
+		reg = <0xe800e800 0x24>;
+		interrupts = <0 250 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 251 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 252 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "error", "rx", "tx";
+		num-cs = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
 };
-- 
1.7.9.5

[PATCH v4 07/15] ARM: shmobile: genmai reference dts: Add RSPI nodes

[Geert Uytterhoeven]

From: Geert Uytterhoeven <geert+renesas@linux-m68k.org>

Add pinctrl and SPI devices for RSPI on Genmai.

On this board, only rspi4 is in use. Its bus contains a single device
(a wm8978 audio codec), for which no bindings are defined yet.

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Cc: devicetree@vger.kernel.org
---
v4:
  - No changes
v3:
  - No changes
v2:
  - Use generic "codec" instead of specific "wm8978" node name.

 arch/arm/boot/dts/r7s72100-genmai-reference.dts |   18 +++++++++++++++++-
 1 file changed, 17 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/r7s72100-genmai-reference.dts b/arch/arm/boot/dts/r7s72100-genmai-reference.dts
index 367af5c133e0..c2cc4bd5a470 100644
--- a/arch/arm/boot/dts/r7s72100-genmai-reference.dts
+++ b/arch/arm/boot/dts/r7s72100-genmai-reference.dts
@@ -43,7 +43,7 @@
 };
 
 &pfc {
-	pinctrl-0 = <&scif2_pins &ethernet_pins>;
+	pinctrl-0 = <&scif2_pins &ethernet_pins &rspi4_pins>;
 	pinctrl-names = "default";
 
 	scif2_pins: serial2 {
@@ -73,6 +73,12 @@
 				 "ethernet_int_p1_15";
 		renesas,function = "ethernet";
 	};
+
+	rspi4_pins: spi4 {
+		renesas,groups = "rspi4_rspck_p4_0", "rspi4_ssl0_p4_1",
+				 "rspi4_mosi_p4_2", "rspi4_miso_p4_3";
+		renesas,function = "rspi4";
+	};
 };
 
 &i2c2 {
@@ -85,3 +91,13 @@
 		pagesize = <64>;
 	};
 };
+
+&spi4 {
+	status = "okay";
+
+	codec: codec@0 {
+		compatible = "wlf,wm8978";
+		reg = <0>;
+		spi-max-frequency = <5000000>;
+	};
+};
-- 
1.7.9.5

[PATCH v3 08/15] ARM: shmobile: r8a7791 clock: add QSPI clocks

[Geert Uytterhoeven]

From: Geert Uytterhoeven <geert+renesas@linux-m68k.org>

The QSPI clock divider value depends on the MD1, MD2, and MD3 mode
switches.

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
v3:
  - No changes
v2:
  - No changes

 arch/arm/mach-shmobile/clock-r8a7791.c |   11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/arch/arm/mach-shmobile/clock-r8a7791.c b/arch/arm/mach-shmobile/clock-r8a7791.c
index 0f4f500e6e1c..fc9248d0b9d0 100644
--- a/arch/arm/mach-shmobile/clock-r8a7791.c
+++ b/arch/arm/mach-shmobile/clock-r8a7791.c
@@ -101,6 +101,7 @@ static struct clk main_clk = {
  */
 SH_FIXED_RATIO_CLK_SET(pll1_clk,		main_clk,	1, 1);
 SH_FIXED_RATIO_CLK_SET(pll3_clk,		main_clk,	1, 1);
+SH_FIXED_RATIO_CLK_SET(qspi_clk,		pll1_clk,	1, 1);
 
 /* fixed ratio clock */
 SH_FIXED_RATIO_CLK_SET(extal_div2_clk,		extal_clk,	1, 2);
@@ -124,6 +125,7 @@ static struct clk *main_clks[] = {
 	&pll3_clk,
 	&hp_clk,
 	&p_clk,
+	&qspi_clk,
 	&rclk_clk,
 	&mp_clk,
 	&cp_clk,
@@ -135,6 +137,7 @@ static struct clk *main_clks[] = {
 /* MSTP */
 enum {
 	MSTP931, MSTP930, MSTP929, MSTP928, MSTP927, MSTP925,
+	MSTP917,
 	MSTP815, MSTP814,
 	MSTP813,
 	MSTP811, MSTP810, MSTP809,
@@ -154,6 +157,7 @@ static struct clk mstp_clks[MSTP_NR] = {
 	[MSTP928] = SH_CLK_MSTP32_STS(&p_clk, SMSTPCR9, 28, MSTPSR9, 0), /* I2C3 */
 	[MSTP927] = SH_CLK_MSTP32_STS(&p_clk, SMSTPCR9, 27, MSTPSR9, 0), /* I2C4 */
 	[MSTP925] = SH_CLK_MSTP32_STS(&p_clk, SMSTPCR9, 25, MSTPSR9, 0), /* I2C5 */
+	[MSTP917] = SH_CLK_MSTP32_STS(&qspi_clk, SMSTPCR9, 17, MSTPSR9, 0), /* QSPI */
 	[MSTP815] = SH_CLK_MSTP32_STS(&zs_clk, SMSTPCR8, 15, MSTPSR8, 0), /* SATA0 */
 	[MSTP814] = SH_CLK_MSTP32_STS(&zs_clk, SMSTPCR8, 14, MSTPSR8, 0), /* SATA1 */
 	[MSTP813] = SH_CLK_MSTP32_STS(&p_clk, SMSTPCR8, 13, MSTPSR8, 0), /* Ether */
@@ -195,6 +199,7 @@ static struct clk_lookup lookups[] = {
 	CLKDEV_CON_ID("zs",		&zs_clk),
 	CLKDEV_CON_ID("hp",		&hp_clk),
 	CLKDEV_CON_ID("p",		&p_clk),
+	CLKDEV_CON_ID("qspi",		&qspi_clk),
 	CLKDEV_CON_ID("rclk",		&rclk_clk),
 	CLKDEV_CON_ID("mp",		&mp_clk),
 	CLKDEV_CON_ID("cp",		&cp_clk),
@@ -220,6 +225,7 @@ static struct clk_lookup lookups[] = {
 	CLKDEV_DEV_ID("sh-sci.13", &mstp_clks[MSTP1106]), /* SCIFA4 */
 	CLKDEV_DEV_ID("sh-sci.14", &mstp_clks[MSTP1107]), /* SCIFA5 */
 	CLKDEV_DEV_ID("sh_cmt.0", &mstp_clks[MSTP124]),
+	CLKDEV_DEV_ID("qspi.0", &mstp_clks[MSTP917]),
 	CLKDEV_DEV_ID("e61f0000.thermal", &mstp_clks[MSTP522]),
 	CLKDEV_DEV_ID("rcar_thermal", &mstp_clks[MSTP522]),
 	CLKDEV_DEV_ID("i2c-rcar_gen2.0", &mstp_clks[MSTP931]),
@@ -271,6 +277,11 @@ void __init r8a7791_clock_init(void)
 		break;
 	}
 
+	if ((mode & (MD(3) | MD(2) | MD(1))) == MD(2))
+		SH_CLK_SET_RATIO(&qspi_clk_ratio, 1, 16);
+	else
+		SH_CLK_SET_RATIO(&qspi_clk_ratio, 1, 20);
+
 	for (k = 0; !ret && (k < ARRAY_SIZE(main_clks)); k++)
 		ret = clk_register(main_clks[k]);
 
-- 
1.7.9.5

[PATCH v3 09/15] ARM: shmobile: koelsch legacy: Add QSPI support

[Geert Uytterhoeven]

From: Geert Uytterhoeven <geert+renesas@linux-m68k.org>

Enable support for the Spansion s25fl512s SPI FLASH on the Koelsch board:
  - Add QSPI platform device, resources, platform data, and pinmux,
  - Add FLASH data and MTD partitions.

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
---
v3:
  - Switch to named IRQs
v2:
  - Split in 2 groups (qspi_ctrl/qspi_data4)

 arch/arm/mach-shmobile/board-koelsch.c |   64 ++++++++++++++++++++++++++++++++
 1 file changed, 64 insertions(+)

diff --git a/arch/arm/mach-shmobile/board-koelsch.c b/arch/arm/mach-shmobile/board-koelsch.c
index 2ab5c75ba2c2..56020d9fa841 100644
--- a/arch/arm/mach-shmobile/board-koelsch.c
+++ b/arch/arm/mach-shmobile/board-koelsch.c
@@ -25,12 +25,17 @@
 #include <linux/input.h>
 #include <linux/kernel.h>
 #include <linux/leds.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
 #include <linux/phy.h>
 #include <linux/pinctrl/machine.h>
 #include <linux/platform_data/gpio-rcar.h>
 #include <linux/platform_data/rcar-du.h>
 #include <linux/platform_device.h>
 #include <linux/sh_eth.h>
+#include <linux/spi/flash.h>
+#include <linux/spi/rspi.h>
+#include <linux/spi/spi.h>
 #include <mach/common.h>
 #include <mach/irqs.h>
 #include <mach/r8a7791.h>
@@ -148,6 +153,55 @@ static const struct gpio_keys_platform_data koelsch_keys_pdata __initconst = {
 	.nbuttons	= ARRAY_SIZE(gpio_buttons),
 };
 
+/* QSPI */
+static const struct resource qspi_resources[] __initconst = {
+	DEFINE_RES_MEM(0xe6b10000, 0x1000),
+	DEFINE_RES_IRQ_NAMED(gic_spi(184), "mux"),
+};
+
+static const struct rspi_plat_data qspi_pdata __initconst = {
+	.num_chipselect = 1,
+};
+
+/* SPI Flash memory (Spansion S25FL512SAGMFIG11 64 MiB) */
+static struct mtd_partition spi_flash_part[] = {
+	{
+		.name		= "loader",
+		.offset		= 0x00000000,
+		.size		= 512 * 1024,
+		.mask_flags	= MTD_WRITEABLE,
+	},
+	{
+		.name		= "bootenv",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= 512 * 1024,
+		.mask_flags	= MTD_WRITEABLE,
+	},
+	{
+		.name		= "data",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= MTDPART_SIZ_FULL,
+	},
+};
+
+static const struct flash_platform_data spi_flash_data = {
+	.name		= "m25p80",
+	.parts		= spi_flash_part,
+	.nr_parts	= ARRAY_SIZE(spi_flash_part),
+	.type		= "s25fl512s",
+};
+
+static const struct spi_board_info spi_info[] __initconst = {
+	{
+		.modalias	= "m25p80",
+		.platform_data	= &spi_flash_data,
+		.mode		= SPI_MODE_0,
+		.max_speed_hz	= 30000000,
+		.bus_num	= 0,
+		.chip_select	= 0,
+	},
+};
+
 /* SATA0 */
 static const struct resource sata0_resources[] __initconst = {
 	DEFINE_RES_MEM(0xee300000, 0x2000),
@@ -180,6 +234,11 @@ static const struct pinctrl_map koelsch_pinctrl_map[] = {
 				  "eth_rmii", "eth"),
 	PIN_MAP_MUX_GROUP_DEFAULT("r8a7791-ether", "pfc-r8a7791",
 				  "intc_irq0", "intc"),
+	/* QSPI */
+	PIN_MAP_MUX_GROUP_DEFAULT("qspi.0", "pfc-r8a7791",
+				  "qspi_ctrl", "qspi"),
+	PIN_MAP_MUX_GROUP_DEFAULT("qspi.0", "pfc-r8a7791",
+				  "qspi_data4", "qspi"),
 	/* SCIF0 (CN19: DEBUG SERIAL0) */
 	PIN_MAP_MUX_GROUP_DEFAULT("sh-sci.6", "pfc-r8a7791",
 				  "scif0_data_d", "scif0"),
@@ -205,6 +264,11 @@ static void __init koelsch_add_standard_devices(void)
 	platform_device_register_data(&platform_bus, "gpio-keys", -1,
 				      &koelsch_keys_pdata,
 				      sizeof(koelsch_keys_pdata));
+	platform_device_register_resndata(&platform_bus, "qspi", 0,
+					  qspi_resources,
+					  ARRAY_SIZE(qspi_resources),
+					  &qspi_pdata, sizeof(qspi_pdata));
+	spi_register_board_info(spi_info, ARRAY_SIZE(spi_info));
 
 	koelsch_add_du_device();
 
-- 
1.7.9.5

[PATCH v3 10/15] ARM: shmobile: koelsch defconfig: Enable RSPI and MTD_M25P80

[Geert Uytterhoeven]

From: Geert Uytterhoeven <geert+renesas@linux-m68k.org>

This enables support for the Spansion s25fl512s SPI FLASH on QSPI.

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
---
v3:
  - No changes
v2:
  - No changes

 arch/arm/configs/koelsch_defconfig |    4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/configs/koelsch_defconfig b/arch/arm/configs/koelsch_defconfig
index e14e0a6836b8..105da42ccd51 100644
--- a/arch/arm/configs/koelsch_defconfig
+++ b/arch/arm/configs/koelsch_defconfig
@@ -40,6 +40,8 @@ CONFIG_DEVTMPFS_MOUNT=y
 CONFIG_BLK_DEV_SD=y
 CONFIG_ATA=y
 CONFIG_SATA_RCAR=y
+CONFIG_MTD=y
+CONFIG_MTD_M25P80=y
 CONFIG_NETDEVICES=y
 # CONFIG_NET_VENDOR_ARC is not set
 # CONFIG_NET_CADENCE is not set
@@ -62,6 +64,8 @@ CONFIG_SH_ETH=y
 CONFIG_SERIAL_SH_SCI=y
 CONFIG_SERIAL_SH_SCI_NR_UARTS=20
 CONFIG_SERIAL_SH_SCI_CONSOLE=y
+CONFIG_SPI=y
+CONFIG_SPI_RSPI=y
 # CONFIG_HWMON is not set
 CONFIG_THERMAL=y
 CONFIG_RCAR_THERMAL=y
-- 
1.7.9.5

[PATCH v2 11/15] ARM: shmobile: r8a7791 dtsi: Add QSPI node

[Geert Uytterhoeven]

From: Geert Uytterhoeven <geert+renesas@linux-m68k.org>

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Cc: devicetree@vger.kernel.org
---
v2:
  - No changes

 arch/arm/boot/dts/r8a7791.dtsi |   12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index d5cc3626dd60..240c4ece1f0c 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -710,4 +710,16 @@
 			clock-output-names = "scifa3", "scifa4", "scifa5";
 		};
 	};
+
+	spi: spi@e6b10000 {
+		compatible = "renesas,qspi-r8a7791", "renesas,qspi";
+		reg = <0 0xe6b10000 0 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 184 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&mstp9_clks R8A7791_CLK_QSPI_MOD>;
+		num-cs = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
 };
-- 
1.7.9.5

[PATCH v2 12/15] ARM: shmobile: koelsch dts: Add QSPI nodes

[Geert Uytterhoeven]

From: Geert Uytterhoeven <geert+renesas@linux-m68k.org>

Add pinctrl and SPI devices for QSPI on Koelsch.
Add Spansion s25fl512s SPI FLASH and MTD partitions.

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Cc: devicetree@vger.kernel.org
---
v2:
  - No changes

 arch/arm/boot/dts/r8a7791-koelsch.dts |   36 +++++++++++++++++++++++++++++++++
 1 file changed, 36 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts
index 55ec36e2a1f1..42fd5ebe9119 100644
--- a/arch/arm/boot/dts/r8a7791-koelsch.dts
+++ b/arch/arm/boot/dts/r8a7791-koelsch.dts
@@ -123,6 +123,11 @@
 		renesas,groups = "scif1_data_d";
 		renesas,function = "scif1";
 	};
+
+	qspi_pins: spi {
+		renesas,groups = "qspi_ctrl", "qspi_data4";
+		renesas,function = "qspi";
+	};
 };
 
 &sata0 {
@@ -142,3 +147,34 @@
 
 	status = "okay";
 };
+
+&spi {
+	pinctrl-0 = <&qspi_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+
+	flash: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spansion,s25fl512s";
+		reg = <0>;
+		spi-max-frequency = <30000000>;
+		m25p,fast-read;
+
+		partition@0 {
+			label = "loader";
+			reg = <0x00000000 0x00080000>;
+			read-only;
+		};
+		partition@80000 {
+			label = "bootenv";
+			reg = <0x00080000 0x00080000>;
+			read-only;
+		};
+		partition@100000 {
+			label = "data";
+			reg = <0x00100000 0x03f00000>;
+		};
+	};
+};
-- 
1.7.9.5

[PATCH 13/15] ARM: shmobile: lager legacy: Switch QSPI to named IRQs

[Geert Uytterhoeven]

From: Geert Uytterhoeven <geert+renesas@linux-m68k.org>

Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
---
 arch/arm/mach-shmobile/board-lager.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/mach-shmobile/board-lager.c b/arch/arm/mach-shmobile/board-lager.c
index 8dde4462f600..4977a4b9fa2c 100644
--- a/arch/arm/mach-shmobile/board-lager.c
+++ b/arch/arm/mach-shmobile/board-lager.c
@@ -290,7 +290,7 @@ static const struct spi_board_info spi_info[] __initconst = {
 /* QSPI resource */
 static const struct resource qspi_resources[] __initconst = {
 	DEFINE_RES_MEM(0xe6b10000, 0x1000),
-	DEFINE_RES_IRQ(gic_spi(184)),
+	DEFINE_RES_IRQ(gic_spi(184), "mux"),
 };
 
 /* VIN */
-- 
1.7.9.5

[PATCH 14/15] ARM: shmobile: koelsch legacy: Enable Quad SPI transfers for the SPI FLASH

[Geert Uytterhoeven]

From: Geert Uytterhoeven <geert+renesas-Td1EMuHUCqxL1ZNQvxDV9g@public.gmane.org>

Signed-off-by: Geert Uytterhoeven <geert+renesas-Td1EMuHUCqxL1ZNQvxDV9g@public.gmane.org>
---
This depends on spi-rspi and m25p80 updates

 arch/arm/mach-shmobile/board-koelsch.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/mach-shmobile/board-koelsch.c b/arch/arm/mach-shmobile/board-koelsch.c
index 56020d9fa841..4cb8674bc4a8 100644
--- a/arch/arm/mach-shmobile/board-koelsch.c
+++ b/arch/arm/mach-shmobile/board-koelsch.c
@@ -195,7 +195,7 @@ static const struct spi_board_info spi_info[] __initconst = {
 	{
 		.modalias	= "m25p80",
 		.platform_data	= &spi_flash_data,
-		.mode		= SPI_MODE_0,
+		.mode		= SPI_MODE_0 | SPI_TX_QUAD | SPI_RX_QUAD,
 		.max_speed_hz	= 30000000,
 		.bus_num	= 0,
 		.chip_select	= 0,
-- 
1.7.9.5

--
To unsubscribe from this list: send the line "unsubscribe linux-spi" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 15/15] ARM: shmobile: koelsch dts: Enable Quad SPI transfers for the SPI FLASH

[Geert Uytterhoeven]

From: Geert Uytterhoeven <geert+renesas-Td1EMuHUCqxL1ZNQvxDV9g@public.gmane.org>

Signed-off-by: Geert Uytterhoeven <geert+renesas-Td1EMuHUCqxL1ZNQvxDV9g@public.gmane.org>
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
---
This depends on spi-rspi and m25p80 updates

 arch/arm/boot/dts/r8a7791-koelsch.dts |    2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts
index 42fd5ebe9119..d4ca21cd2c34 100644
--- a/arch/arm/boot/dts/r8a7791-koelsch.dts
+++ b/arch/arm/boot/dts/r8a7791-koelsch.dts
@@ -160,6 +160,8 @@
 		compatible = "spansion,s25fl512s";
 		reg = <0>;
 		spi-max-frequency = <30000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
 		m25p,fast-read;
 
 		partition@0 {
-- 
1.7.9.5

--
To unsubscribe from this list: send the line "unsubscribe linux-spi" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html