linux-spi.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Andrew Bresticker <abrestic-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org>
To: Mark Brown <broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Cc: Sifan Naeem <sifan.naeem-1AXoQHu6uovQT0dZR+AlfA@public.gmane.org>,
	linux-spi-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	Andrew Bresticker
	<abrestic-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org>
Subject: [PATCH V2 2/2] spi: img-spfi: Select FIFO based on transfer length
Date: Mon, 22 Dec 2014 11:35:16 -0800	[thread overview]
Message-ID: <1419276916-28433-2-git-send-email-abrestic@chromium.org> (raw)
In-Reply-To: <1419276916-28433-1-git-send-email-abrestic-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org>

Since the 32-bit FIFO is deeper (64 bytes) than the 8-bit FIFO (16 bytes),
use the 32-bit FIFO when there are at least 32 bits remaining to be
transferred in PIO mode or when the transfer length is 32-bit aligned
in DMA mode.

Signed-off-by: Andrew Bresticker <abrestic-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org>
---
 drivers/spi/spi-img-spfi.c | 49 ++++++++++++++++++----------------------------
 1 file changed, 19 insertions(+), 30 deletions(-)

diff --git a/drivers/spi/spi-img-spfi.c b/drivers/spi/spi-img-spfi.c
index aad6683..c01567d 100644
--- a/drivers/spi/spi-img-spfi.c
+++ b/drivers/spi/spi-img-spfi.c
@@ -160,16 +160,16 @@ static unsigned int spfi_pio_write32(struct img_spfi *spfi, const u32 *buf,
 	unsigned int count = 0;
 	u32 status;
 
-	while (count < max) {
+	while (count < max / 4) {
 		spfi_writel(spfi, SPFI_INTERRUPT_SDFUL, SPFI_INTERRUPT_CLEAR);
 		status = spfi_readl(spfi, SPFI_INTERRUPT_STATUS);
 		if (status & SPFI_INTERRUPT_SDFUL)
 			break;
-		spfi_writel(spfi, buf[count / 4], SPFI_TX_32BIT_VALID_DATA);
-		count += 4;
+		spfi_writel(spfi, buf[count], SPFI_TX_32BIT_VALID_DATA);
+		count++;
 	}
 
-	return count;
+	return count * 4;
 }
 
 static unsigned int spfi_pio_write8(struct img_spfi *spfi, const u8 *buf,
@@ -196,17 +196,17 @@ static unsigned int spfi_pio_read32(struct img_spfi *spfi, u32 *buf,
 	unsigned int count = 0;
 	u32 status;
 
-	while (count < max) {
+	while (count < max / 4) {
 		spfi_writel(spfi, SPFI_INTERRUPT_GDEX32BIT,
 			    SPFI_INTERRUPT_CLEAR);
 		status = spfi_readl(spfi, SPFI_INTERRUPT_STATUS);
 		if (!(status & SPFI_INTERRUPT_GDEX32BIT))
 			break;
-		buf[count / 4] = spfi_readl(spfi, SPFI_RX_32BIT_VALID_DATA);
-		count += 4;
+		buf[count] = spfi_readl(spfi, SPFI_RX_32BIT_VALID_DATA);
+		count++;
 	}
 
-	return count;
+	return count * 4;
 }
 
 static unsigned int spfi_pio_read8(struct img_spfi *spfi, u8 *buf,
@@ -251,17 +251,15 @@ static int img_spfi_start_pio(struct spi_master *master,
 	       time_before(jiffies, timeout)) {
 		unsigned int tx_count, rx_count;
 
-		switch (xfer->bits_per_word) {
-		case 32:
+		if (tx_bytes >= 4)
 			tx_count = spfi_pio_write32(spfi, tx_buf, tx_bytes);
-			rx_count = spfi_pio_read32(spfi, rx_buf, rx_bytes);
-			break;
-		case 8:
-		default:
+		else
 			tx_count = spfi_pio_write8(spfi, tx_buf, tx_bytes);
+
+		if (rx_bytes >= 4)
+			rx_count = spfi_pio_read32(spfi, rx_buf, rx_bytes);
+		else
 			rx_count = spfi_pio_read8(spfi, rx_buf, rx_bytes);
-			break;
-		}
 
 		tx_buf += tx_count;
 		rx_buf += rx_count;
@@ -331,14 +329,11 @@ static int img_spfi_start_dma(struct spi_master *master,
 
 	if (xfer->rx_buf) {
 		rxconf.direction = DMA_DEV_TO_MEM;
-		switch (xfer->bits_per_word) {
-		case 32:
+		if (xfer->len % 4 == 0) {
 			rxconf.src_addr = spfi->phys + SPFI_RX_32BIT_VALID_DATA;
 			rxconf.src_addr_width = 4;
 			rxconf.src_maxburst = 4;
-			break;
-		case 8:
-		default:
+		} else {
 			rxconf.src_addr = spfi->phys + SPFI_RX_8BIT_VALID_DATA;
 			rxconf.src_addr_width = 1;
 			rxconf.src_maxburst = 4;
@@ -358,18 +353,14 @@ static int img_spfi_start_dma(struct spi_master *master,
 
 	if (xfer->tx_buf) {
 		txconf.direction = DMA_MEM_TO_DEV;
-		switch (xfer->bits_per_word) {
-		case 32:
+		if (xfer->len % 4 == 0) {
 			txconf.dst_addr = spfi->phys + SPFI_TX_32BIT_VALID_DATA;
 			txconf.dst_addr_width = 4;
 			txconf.dst_maxburst = 4;
-			break;
-		case 8:
-		default:
+		} else {
 			txconf.dst_addr = spfi->phys + SPFI_TX_8BIT_VALID_DATA;
 			txconf.dst_addr_width = 1;
 			txconf.dst_maxburst = 4;
-			break;
 		}
 		dmaengine_slave_config(spfi->tx_ch, &txconf);
 
@@ -508,9 +499,7 @@ static void img_spfi_set_cs(struct spi_device *spi, bool enable)
 static bool img_spfi_can_dma(struct spi_master *master, struct spi_device *spi,
 			     struct spi_transfer *xfer)
 {
-	if (xfer->bits_per_word == 8 && xfer->len > SPFI_8BIT_FIFO_SIZE)
-		return true;
-	if (xfer->bits_per_word == 32 && xfer->len > SPFI_32BIT_FIFO_SIZE)
+	if (xfer->len > SPFI_32BIT_FIFO_SIZE)
 		return true;
 	return false;
 }
-- 
2.2.0.rc0.207.ga3a616c

--
To unsubscribe from this list: send the line "unsubscribe linux-spi" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

  parent reply	other threads:[~2014-12-22 19:35 UTC|newest]

Thread overview: 3+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2014-12-22 19:35 [PATCH V2 1/2] spi: img-spfi: Increase DMA burst size Andrew Bresticker
     [not found] ` <1419276916-28433-1-git-send-email-abrestic-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org>
2014-12-22 19:35   ` Andrew Bresticker [this message]
2014-12-24 12:20   ` Mark Brown

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1419276916-28433-2-git-send-email-abrestic@chromium.org \
    --to=abrestic-f7+t8e8rja9g9huczpvpmw@public.gmane.org \
    --cc=broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
    --cc=linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
    --cc=linux-spi-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
    --cc=sifan.naeem-1AXoQHu6uovQT0dZR+AlfA@public.gmane.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).