From: Varadarajan Narayanan <varada@codeaurora.org>
To: broonie@kernel.org, robh+dt@kernel.org, mark.rutland@arm.com,
andy.gross@linaro.org, david.brown@linaro.org,
linux-spi@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, linux-arm-msm@vger.kernel.org,
linux-soc@vger.kernel.org
Cc: Varadarajan Narayanan <varada@codeaurora.org>
Subject: [PATCH v3 00/15] spi: qup: Fixes and add support for >64k transfers
Date: Tue, 20 Jun 2017 14:40:42 +0530 [thread overview]
Message-ID: <1497949857-1852-1-git-send-email-varada@codeaurora.org> (raw)
v3:
Fix git bisect-ability issues in
spi: qup: Add completion structures for DMA
spi: qup: Add completion timeout
spi: qup: Place the QUP in run mode before DMA
spi: qup: Fix transaction done signaling
v2:
Incorporate feedback from Andy Gross, Sricharan, Stanimir Varbanov
Modified the QUP-v1 dma completion sequence to QUP-v2 as per feedback.
Removed code that used controller->xfer to identify extra interrupts,
since with the fixes done to handle i/o completion we don't see
extra interrupts.
v1:
This series fixes some existing issues in the code for both
interrupt and dma mode. Patches 1 - 11 are the fixes.
Random failures/timeout are observed without these fixes.
Also, the current driver does not support block transfers > 64K
and the driver quietly fails. Patches 12 - 18 add support for this
in both interrupt and dma mode.
The entire series has been tested on ipq4019 with
SPI-NOR flash for block sizes > 64k.
Varadarajan Narayanan (15):
spi: qup: Enable chip select support
spi: qup: Setup DMA mode correctly
spi: qup: Add completion structures for DMA
spi: qup: Add completion timeout
spi: qup: Place the QUP in run mode before DMA
spi: qup: Fix error handling in spi_qup_prep_sg
spi: qup: Fix transaction done signaling
spi: qup: Do block sized read/write in block mode
spi: qup: refactor spi_qup_io_config into two functions
spi: qup: call io_config in mode specific function
spi: qup: allow block mode to generate multiple transactions
spi: qup: refactor spi_qup_prep_sg
spi: qup: allow multiple DMA transactions per spi xfer
spi: qup: Ensure done detection
spi: qup: support for qup v1 dma
.../devicetree/bindings/spi/qcom,spi-qup.txt | 6 +
drivers/spi/spi-qup.c | 630 ++++++++++++++-------
2 files changed, 441 insertions(+), 195 deletions(-)
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
next reply other threads:[~2017-06-20 9:10 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-06-20 9:10 Varadarajan Narayanan [this message]
2017-06-20 9:10 ` [PATCH v3 01/15] spi: qup: Enable chip select support Varadarajan Narayanan
2017-06-20 9:10 ` [PATCH v3 02/15] spi: qup: Setup DMA mode correctly Varadarajan Narayanan
2017-06-20 9:10 ` [PATCH v3 03/15] spi: qup: Add completion structures for DMA Varadarajan Narayanan
[not found] ` <1497949857-1852-1-git-send-email-varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2017-06-20 9:10 ` [PATCH v3 04/15] spi: qup: Add completion timeout Varadarajan Narayanan
2017-06-20 9:10 ` [PATCH v3 13/15] spi: qup: allow multiple DMA transactions per spi xfer Varadarajan Narayanan
2017-06-20 9:10 ` [PATCH v3 14/15] spi: qup: Ensure done detection Varadarajan Narayanan
2017-06-20 9:10 ` [PATCH v3 05/15] spi: qup: Place the QUP in run mode before DMA Varadarajan Narayanan
2017-06-20 9:10 ` [PATCH v3 06/15] spi: qup: Fix error handling in spi_qup_prep_sg Varadarajan Narayanan
2017-06-20 9:10 ` [PATCH v3 07/15] spi: qup: Fix transaction done signaling Varadarajan Narayanan
2017-08-08 11:18 ` Applied "spi: qup: Fix transaction done signaling" to the spi tree Mark Brown
2017-06-20 9:10 ` [PATCH v3 08/15] spi: qup: Do block sized read/write in block mode Varadarajan Narayanan
2017-06-20 9:10 ` [PATCH v3 09/15] spi: qup: refactor spi_qup_io_config into two functions Varadarajan Narayanan
2017-06-20 9:10 ` [PATCH v3 10/15] spi: qup: call io_config in mode specific function Varadarajan Narayanan
2017-06-20 9:10 ` [PATCH v3 11/15] spi: qup: allow block mode to generate multiple transactions Varadarajan Narayanan
2017-06-20 9:10 ` [PATCH v3 12/15] spi: qup: refactor spi_qup_prep_sg Varadarajan Narayanan
2017-06-20 9:10 ` [PATCH v3 15/15] spi: qup: support for qup v1 dma Varadarajan Narayanan
2017-06-23 21:49 ` Rob Herring
2017-06-27 9:36 ` Varadarajan Narayanan
2017-06-28 6:47 ` Andy Gross
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1497949857-1852-1-git-send-email-varada@codeaurora.org \
--to=varada@codeaurora.org \
--cc=andy.gross@linaro.org \
--cc=broonie@kernel.org \
--cc=david.brown@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-soc@vger.kernel.org \
--cc=linux-spi@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).