From: Keiji Hayashibara <hayashibara.keiji@socionext.com>
To: broonie@kernel.org, yamada.masahiro@socionext.com,
linux-spi@vger.kernel.org, linux-arm-kernel@lists.infradead.org
Cc: masami.hiramatsu@linaro.org, jaswinder.singh@linaro.org,
linux-kernel@vger.kernel.org, hayashibara.keiji@socionext.com
Subject: [PATCH 3/3] spi: uniphier: introduce polling mode
Date: Tue, 3 Sep 2019 14:31:01 +0900 [thread overview]
Message-ID: <1567488661-11428-4-git-send-email-hayashibara.keiji@socionext.com> (raw)
In-Reply-To: <1567488661-11428-1-git-send-email-hayashibara.keiji@socionext.com>
Introduce new polling mode for short size transfer. Either the estimated
transfer time is estimated to exceed 200us, or polling loop actually exceeds
200us, it switches to irq mode.
Signed-off-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
---
drivers/spi/spi-uniphier.c | 81 +++++++++++++++++++++++++++++++++++++---------
1 file changed, 66 insertions(+), 15 deletions(-)
diff --git a/drivers/spi/spi-uniphier.c b/drivers/spi/spi-uniphier.c
index d40ad93..6b83b25 100644
--- a/drivers/spi/spi-uniphier.c
+++ b/drivers/spi/spi-uniphier.c
@@ -7,6 +7,7 @@
#include <linux/bitfield.h>
#include <linux/bitops.h>
#include <linux/clk.h>
+#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/module.h>
@@ -16,6 +17,7 @@
#include <asm/unaligned.h>
#define SSI_TIMEOUT_MS 2000
+#define SSI_POLL_TIMEOUT_US 200
#define SSI_MAX_CLK_DIVIDER 254
#define SSI_MIN_CLK_DIVIDER 4
@@ -290,21 +292,23 @@ static void uniphier_spi_recv(struct uniphier_spi_priv *priv)
static void uniphier_spi_fill_tx_fifo(struct uniphier_spi_priv *priv)
{
- unsigned int tx_count;
+ unsigned int fifo_threshold, fill_bytes;
u32 val;
- tx_count = DIV_ROUND_UP(priv->tx_bytes,
+ fifo_threshold = DIV_ROUND_UP(priv->rx_bytes,
bytes_per_word(priv->bits_per_word));
- tx_count = min(tx_count, SSI_FIFO_DEPTH);
+ fifo_threshold = min(fifo_threshold, SSI_FIFO_DEPTH);
+
+ fill_bytes = fifo_threshold - (priv->rx_bytes - priv->tx_bytes);
/* set fifo threshold */
val = readl(priv->base + SSI_FC);
val &= ~(SSI_FC_TXFTH_MASK | SSI_FC_RXFTH_MASK);
- val |= FIELD_PREP(SSI_FC_TXFTH_MASK, tx_count);
- val |= FIELD_PREP(SSI_FC_RXFTH_MASK, tx_count);
+ val |= FIELD_PREP(SSI_FC_TXFTH_MASK, fifo_threshold);
+ val |= FIELD_PREP(SSI_FC_RXFTH_MASK, fifo_threshold);
writel(val, priv->base + SSI_FC);
- while (tx_count--)
+ while (fill_bytes--)
uniphier_spi_send(priv);
}
@@ -323,20 +327,14 @@ static void uniphier_spi_set_cs(struct spi_device *spi, bool enable)
writel(val, priv->base + SSI_FPS);
}
-static int uniphier_spi_transfer_one(struct spi_master *master,
- struct spi_device *spi,
- struct spi_transfer *t)
+static int uniphier_spi_transfer_one_irq(struct spi_master *master,
+ struct spi_device *spi,
+ struct spi_transfer *t)
{
struct uniphier_spi_priv *priv = spi_master_get_devdata(master);
struct device *dev = master->dev.parent;
unsigned long time_left;
- /* Terminate and return success for 0 byte length transfer */
- if (!t->len)
- return 0;
-
- uniphier_spi_setup_transfer(spi, t);
-
reinit_completion(&priv->xfer_done);
uniphier_spi_fill_tx_fifo(priv);
@@ -356,6 +354,59 @@ static int uniphier_spi_transfer_one(struct spi_master *master,
return priv->error;
}
+static int uniphier_spi_transfer_one_poll(struct spi_master *master,
+ struct spi_device *spi,
+ struct spi_transfer *t)
+{
+ struct uniphier_spi_priv *priv = spi_master_get_devdata(master);
+ int loop = SSI_POLL_TIMEOUT_US * 10;
+
+ while (priv->tx_bytes) {
+ uniphier_spi_fill_tx_fifo(priv);
+
+ while ((priv->rx_bytes - priv->tx_bytes) > 0) {
+ while (!(readl(priv->base + SSI_SR) & SSI_SR_RNE)
+ && loop--)
+ ndelay(100);
+
+ if (loop == -1)
+ goto irq_transfer;
+
+ uniphier_spi_recv(priv);
+ }
+ }
+
+ return 0;
+
+irq_transfer:
+ return uniphier_spi_transfer_one_irq(master, spi, t);
+}
+
+static int uniphier_spi_transfer_one(struct spi_master *master,
+ struct spi_device *spi,
+ struct spi_transfer *t)
+{
+ struct uniphier_spi_priv *priv = spi_master_get_devdata(master);
+ unsigned long threshold;
+
+ /* Terminate and return success for 0 byte length transfer */
+ if (!t->len)
+ return 0;
+
+ uniphier_spi_setup_transfer(spi, t);
+
+ /*
+ * If the transfer operation will take longer than
+ * SSI_POLL_TIMEOUT_US, it should use irq.
+ */
+ threshold = DIV_ROUND_UP(SSI_POLL_TIMEOUT_US * priv->speed_hz,
+ USEC_PER_SEC * BITS_PER_BYTE);
+ if (t->len > threshold)
+ return uniphier_spi_transfer_one_irq(master, spi, t);
+ else
+ return uniphier_spi_transfer_one_poll(master, spi, t);
+}
+
static int uniphier_spi_prepare_transfer_hardware(struct spi_master *master)
{
struct uniphier_spi_priv *priv = spi_master_get_devdata(master);
--
2.7.4
next prev parent reply other threads:[~2019-09-03 5:31 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-09-03 5:30 [PATCH 0/3] spi: uniphier: introduce polling mode and fix bug Keiji Hayashibara
2019-09-03 5:30 ` [PATCH 1/3] spi: uniphier: fix wrong register overwrite Keiji Hayashibara
2019-09-03 11:57 ` Applied "spi: uniphier: fix wrong register overwrite" to the spi tree Mark Brown
2019-09-03 5:31 ` [PATCH 2/3] spi: uniphier: remove unnecessary code Keiji Hayashibara
2019-09-03 11:57 ` Applied "spi: uniphier: remove unnecessary code" to the spi tree Mark Brown
2019-09-03 5:31 ` Keiji Hayashibara [this message]
2019-09-03 11:57 ` Applied "spi: uniphier: introduce polling mode" " Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1567488661-11428-4-git-send-email-hayashibara.keiji@socionext.com \
--to=hayashibara.keiji@socionext.com \
--cc=broonie@kernel.org \
--cc=jaswinder.singh@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-spi@vger.kernel.org \
--cc=masami.hiramatsu@linaro.org \
--cc=yamada.masahiro@socionext.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).