linux-spi.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
To: Naga Sureshkumar Relli <nagasuresh.relli@microchip.com>,
	broonie@kernel.org, robh+dt@kernel.org,
	krzysztof.kozlowski+dt@linaro.org, conor.dooley@microchip.com
Cc: linux-spi@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org
Subject: Re: [PATCH 2/2] spi: microchip-core-qspi: Add support for microchip fpga qspi controllers
Date: Tue, 2 Aug 2022 10:54:03 +0200	[thread overview]
Message-ID: <17a48c8d-fa66-95ba-4666-f4496425bd03@linaro.org> (raw)
In-Reply-To: <20220801094255.664548-3-nagasuresh.relli@microchip.com>

On 01/08/2022 11:42, Naga Sureshkumar Relli wrote:
> Add a driver for Microchip FPGA QSPI controllers. This driver also
> supports "hard" QSPI controllers on Polarfire SoC.
> 
> Signed-off-by: Naga Sureshkumar Relli <nagasuresh.relli@microchip.com>

Thank you for your patch. There is something to discuss/improve.

> +	qspi = spi_controller_get_devdata(ctlr);
> +	platform_set_drvdata(pdev, qspi);
> +
> +	qspi->regs = devm_platform_ioremap_resource(pdev, 0);
> +	if (IS_ERR(qspi->regs)) {
> +		ret = PTR_ERR(qspi->regs);
> +		goto remove_master;
> +	}
> +
> +	qspi->clk = devm_clk_get(&pdev->dev, NULL);
> +	if (IS_ERR(qspi->clk)) {
> +		dev_err(&pdev->dev, "clock not found.\n");
> +		ret = PTR_ERR(qspi->clk);

dev_err_probe() for the two of above.

> +		goto remove_master;
> +	}
> +
> +	ret = clk_prepare_enable(qspi->clk);
> +	if (ret) {
> +		dev_err(&pdev->dev, "failed to enable clock\n");
> +		goto remove_master;
> +	}
> +
> +	init_completion(&qspi->data_completion);
> +	mutex_init(&qspi->op_lock);
> +
> +	qspi->irq = platform_get_irq(pdev, 0);
> +	if (qspi->irq <= 0) {
> +		ret = qspi->irq;
> +		goto clk_dis_all;
> +	}
> +
> +	ret = devm_request_irq(&pdev->dev, qspi->irq, mchp_coreqspi_isr,
> +			       0, pdev->name, qspi);
> +	if (ret != 0) {
> +		dev_err(&pdev->dev, "request_irq failed %d\n", ret);
> +		goto clk_dis_all;
> +	}
> +
> +	ctlr->bits_per_word_mask = SPI_BPW_MASK(8);
> +	ctlr->mem_ops = &mchp_coreqspi_mem_ops;
> +	ctlr->setup = mchp_coreqspi_setup_op;
> +	ctlr->mode_bits = SPI_CPOL | SPI_CPHA | SPI_RX_DUAL | SPI_RX_QUAD |
> +			  SPI_TX_DUAL | SPI_TX_QUAD;
> +	ctlr->dev.of_node = np;
> +
> +	ret = devm_spi_register_controller(&pdev->dev, ctlr);
> +	if (ret) {
> +		dev_err(&pdev->dev, "spi_register_controller failed\n");
> +		goto clk_dis_all;
> +	}
> +
> +	return 0;
> +
> +clk_dis_all:
> +	clk_disable_unprepare(qspi->clk);
> +remove_master:
> +	spi_controller_put(ctlr);
> +
> +	return ret;
> +}
> +
> +static int mchp_coreqspi_remove(struct platform_device *pdev)
> +{
> +	struct mchp_coreqspi *qspi = platform_get_drvdata(pdev);
> +	u32 control = readl_relaxed(qspi->regs + REG_CONTROL);
> +
> +	mchp_coreqspi_disable_ints(qspi);
> +	control &= ~CONTROL_ENABLE;
> +	writel_relaxed(control, qspi->regs + REG_CONTROL);
> +	clk_disable_unprepare(qspi->clk);
> +
> +	return 0;
> +}
> +
> +/*
> + * Platform driver data structure
> + */

Drop such comments.

> +static const struct of_device_id mchp_coreqspi_of_match[] = {
> +	{ .compatible = "microchip,mpfs-qspi" },
> +	{ .compatible = "microchip,coreqspi-rtl-v2" },
> +	{ /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, mchp_coreqspi_of_match);
> +
> +static struct platform_driver mchp_coreqspi_driver = {
> +	.probe = mchp_coreqspi_probe,
> +	.driver = {
> +		.name = "microchip,mpfs-qspi",
> +		.of_match_table = mchp_coreqspi_of_match,
> +	},
> +	.remove = mchp_coreqspi_remove,
> +};
> +module_platform_driver(mchp_coreqspi_driver);
> +
> +MODULE_AUTHOR("Naga Sureshkumar Relli <nagasuresh.relli@microchip.com");
> +MODULE_DESCRIPTION("Microchip coreQSPI QSPI controller driver");
> +MODULE_LICENSE("GPL");


Best regards,
Krzysztof

      parent reply	other threads:[~2022-08-02  8:54 UTC|newest]

Thread overview: 19+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-08-01  9:42 [PATCH 0/2] Add support for Microchip QSPI controller Naga Sureshkumar Relli
2022-08-01  9:42 ` [PATCH 1/2] spi: dt-binding: add Microchip CoreQSPI compatible Naga Sureshkumar Relli
2022-08-01 10:17   ` Conor.Dooley
2022-08-01 10:52     ` naga sureshkumar
2022-08-02  8:52   ` Krzysztof Kozlowski
2022-08-02 13:13     ` Mark Brown
2022-08-03  6:11       ` Krzysztof Kozlowski
2022-08-03  6:59         ` naga sureshkumar
2022-08-03  7:48           ` Krzysztof Kozlowski
2022-08-03 13:29         ` Mark Brown
2022-08-04 11:31           ` Krzysztof Kozlowski
2022-08-04 11:35             ` Krzysztof Kozlowski
2022-08-04 12:13             ` Mark Brown
2022-08-01  9:42 ` [PATCH 2/2] spi: microchip-core-qspi: Add support for microchip fpga qspi controllers Naga Sureshkumar Relli
2022-08-01 10:40   ` Conor.Dooley
2022-08-01 11:09     ` naga sureshkumar
2022-08-01 12:33     ` Mark Brown
2022-08-01 12:56       ` Conor.Dooley
2022-08-02  8:54   ` Krzysztof Kozlowski [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=17a48c8d-fa66-95ba-4666-f4496425bd03@linaro.org \
    --to=krzysztof.kozlowski@linaro.org \
    --cc=broonie@kernel.org \
    --cc=conor.dooley@microchip.com \
    --cc=devicetree@vger.kernel.org \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-spi@vger.kernel.org \
    --cc=nagasuresh.relli@microchip.com \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).