From: Richard Genoud <richard.genoud@gmail.com>
To: Radu Pirea <radu.pirea@microchip.com>,
broonie@kernel.org, nicolas.ferre@microchip.com,
alexandre.belloni@bootlin.com, lee.jones@linaro.org,
richard.genoud@gmail.com, robh+dt@kernel.org,
mark.rutland@arm.com, gregkh@linuxfoundation.org
Cc: linux-spi@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, devicetree@vger.kernel.org,
linux-serial@vger.kernel.org
Subject: Re: [PATCH v6 6/6] tty/serial: atmel: change the driver to work under at91-usart mfd
Date: Thu, 7 Jun 2018 15:42:21 +0200 [thread overview]
Message-ID: <42c20ca1-6d27-71c2-83cf-2e5f113e8dc9@sorico.fr> (raw)
In-Reply-To: <20180607110020.20565-7-radu.pirea@microchip.com>
On 07/06/2018 13:00, Radu Pirea wrote:
> This patch modifies the place where resources and device tree properties
> are searched.
>
> Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
> ---
> drivers/tty/serial/Kconfig | 1 +
> drivers/tty/serial/atmel_serial.c | 42 ++++++++++++++++++++-----------
> 2 files changed, 28 insertions(+), 15 deletions(-)
>
> diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
> index 3682fd3e960c..25e55332f8b1 100644
> --- a/drivers/tty/serial/Kconfig
> +++ b/drivers/tty/serial/Kconfig
> @@ -119,6 +119,7 @@ config SERIAL_ATMEL
> depends on ARCH_AT91 || COMPILE_TEST
> select SERIAL_CORE
> select SERIAL_MCTRL_GPIO if GPIOLIB
> + select MFD_AT91_USART
> help
> This enables the driver for the on-chip UARTs of the Atmel
> AT91 processors.
> diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
> index df46a9e88c34..5ef8a6a6fe17 100644
> --- a/drivers/tty/serial/atmel_serial.c
> +++ b/drivers/tty/serial/atmel_serial.c
> @@ -193,8 +193,7 @@ static struct console atmel_console;
>
> #if defined(CONFIG_OF)
> static const struct of_device_id atmel_serial_dt_ids[] = {
> - { .compatible = "atmel,at91rm9200-usart" },
> - { .compatible = "atmel,at91sam9260-usart" },
> + { .compatible = "atmel,at91rm9200-usart-serial" },
> { /* sentinel */ }
> };
> #endif
> @@ -915,6 +914,7 @@ static void atmel_tx_dma(struct uart_port *port)
> static int atmel_prepare_tx_dma(struct uart_port *port)
> {
> struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
> + struct device *mfd_dev = port->dev->parent;
> dma_cap_mask_t mask;
> struct dma_slave_config config;
> int ret, nent;
> @@ -922,7 +922,7 @@ static int atmel_prepare_tx_dma(struct uart_port *port)
> dma_cap_zero(mask);
> dma_cap_set(DMA_SLAVE, mask);
>
> - atmel_port->chan_tx = dma_request_slave_channel(port->dev, "tx");
> + atmel_port->chan_tx = dma_request_slave_channel(mfd_dev, "tx");
> if (atmel_port->chan_tx == NULL)
> goto chan_err;
> dev_info(port->dev, "using %s for tx DMA transfers\n",
> @@ -1093,6 +1093,7 @@ static void atmel_rx_from_dma(struct uart_port *port)
> static int atmel_prepare_rx_dma(struct uart_port *port)
> {
> struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
> + struct device *mfd_dev = port->dev->parent;
> struct dma_async_tx_descriptor *desc;
> dma_cap_mask_t mask;
> struct dma_slave_config config;
> @@ -1104,7 +1105,7 @@ static int atmel_prepare_rx_dma(struct uart_port *port)
> dma_cap_zero(mask);
> dma_cap_set(DMA_CYCLIC, mask);
>
> - atmel_port->chan_rx = dma_request_slave_channel(port->dev, "rx");
> + atmel_port->chan_rx = dma_request_slave_channel(mfd_dev, "rx");
> if (atmel_port->chan_rx == NULL)
> goto chan_err;
> dev_info(port->dev, "using %s for rx DMA transfers\n",
> @@ -2222,8 +2223,8 @@ static const char *atmel_type(struct uart_port *port)
> */
> static void atmel_release_port(struct uart_port *port)
> {
> - struct platform_device *pdev = to_platform_device(port->dev);
> - int size = pdev->resource[0].end - pdev->resource[0].start + 1;
> + struct platform_device *mpdev = to_platform_device(port->dev->parent);
> + int size = resource_size(mpdev->resource);
>
> release_mem_region(port->mapbase, size);
>
> @@ -2238,8 +2239,8 @@ static void atmel_release_port(struct uart_port *port)
> */
> static int atmel_request_port(struct uart_port *port)
> {
> - struct platform_device *pdev = to_platform_device(port->dev);
> - int size = pdev->resource[0].end - pdev->resource[0].start + 1;
> + struct platform_device *mpdev = to_platform_device(port->dev->parent);
> + int size = resource_size(mpdev->resource);
>
> if (!request_mem_region(port->mapbase, size, "atmel_serial"))
> return -EBUSY;
> @@ -2341,27 +2342,28 @@ static int atmel_init_port(struct atmel_uart_port *atmel_port,
> {
> int ret;
> struct uart_port *port = &atmel_port->uart;
> + struct platform_device *mpdev = to_platform_device(pdev->dev.parent);
>
> atmel_init_property(atmel_port, pdev);
> atmel_set_ops(port);
>
> - uart_get_rs485_mode(&pdev->dev, &port->rs485);
> + uart_get_rs485_mode(&mpdev->dev, &port->rs485);
>
> port->iotype = UPIO_MEM;
> port->flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP;
> port->ops = &atmel_pops;
> port->fifosize = 1;
> port->dev = &pdev->dev;
> - port->mapbase = pdev->resource[0].start;
> - port->irq = pdev->resource[1].start;
> + port->mapbase = mpdev->resource[0].start;
> + port->irq = mpdev->resource[1].start;
> port->rs485_config = atmel_config_rs485;
> - port->membase = NULL;
> + port->membase = NULL;
>
> memset(&atmel_port->rx_ring, 0, sizeof(atmel_port->rx_ring));
>
> /* for console, the clock could already be configured */
> if (!atmel_port->clk) {
> - atmel_port->clk = clk_get(&pdev->dev, "usart");
> + atmel_port->clk = clk_get(&mpdev->dev, "usart");
> if (IS_ERR(atmel_port->clk)) {
> ret = PTR_ERR(atmel_port->clk);
> atmel_port->clk = NULL;
> @@ -2694,13 +2696,22 @@ static void atmel_serial_probe_fifos(struct atmel_uart_port *atmel_port,
> static int atmel_serial_probe(struct platform_device *pdev)
> {
> struct atmel_uart_port *atmel_port;
> - struct device_node *np = pdev->dev.of_node;
> + struct device_node *np = pdev->dev.parent->of_node;
> void *data;
> int ret = -ENODEV;
> bool rs485_enabled;
>
> BUILD_BUG_ON(ATMEL_SERIAL_RINGSIZE & (ATMEL_SERIAL_RINGSIZE - 1));
>
> + /*
> + * In device tree is no node with "atmel,at91rm9200-usart-serial"
I think you meant :
In device tree *there* is no...
With that,
Acked-by: Richard Genoud <richard.genoud@gmail.com>
> + * as compatible string. This driver is probed by at91-usart mfd driver
> + * which is just a wrapper over the atmel_serial driver and
> + * spi-at91-usart driver. All attributes needed by this driver are
> + * found in of_node of parent.
> + */
> + pdev->dev.of_node = np;
> +
> ret = of_alias_get_id(np, "serial");
> if (ret < 0)
> /* port id not found in platform data nor device-tree aliases:
> @@ -2835,6 +2846,7 @@ static int atmel_serial_remove(struct platform_device *pdev)
>
> clk_put(atmel_port->clk);
> atmel_port->clk = NULL;
> + pdev->dev.of_node = NULL;
>
> return ret;
> }
> @@ -2845,7 +2857,7 @@ static struct platform_driver atmel_serial_driver = {
> .suspend = atmel_serial_suspend,
> .resume = atmel_serial_resume,
> .driver = {
> - .name = "atmel_usart",
> + .name = "atmel_usart_serial",
> .of_match_table = of_match_ptr(atmel_serial_dt_ids),
> },
> };
>
Thanks !
Richard.
next prev parent reply other threads:[~2018-06-07 13:42 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-06-07 11:00 [PATCH v6 0/6] Driver for at91 usart in spi mode Radu Pirea
2018-06-07 11:00 ` [PATCH v6 1/6] MAINTAINERS: add at91 usart mfd driver Radu Pirea
2018-06-07 11:00 ` [PATCH v6 2/6] dt-bindings: add binding for atmel-usart in SPI mode Radu Pirea
2018-06-11 15:37 ` Alexandre Belloni
2018-06-07 11:00 ` [PATCH v6 3/6] mfd: at91-usart: added mfd driver for usart Radu Pirea
2018-06-11 15:36 ` Alexandre Belloni
2018-06-07 11:00 ` [PATCH v6 4/6] MAINTAINERS: add at91 usart spi driver Radu Pirea
2018-06-07 11:00 ` [PATCH v6 5/6] spi: at91-usart: add driver for at91-usart as spi Radu Pirea
2018-06-07 11:00 ` [PATCH v6 6/6] tty/serial: atmel: change the driver to work under at91-usart mfd Radu Pirea
2018-06-07 13:42 ` Richard Genoud [this message]
2018-06-07 13:18 ` [PATCH v6 0/6] Driver for at91 usart in spi mode Andy Shevchenko
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=42c20ca1-6d27-71c2-83cf-2e5f113e8dc9@sorico.fr \
--to=richard.genoud@gmail.com \
--cc=alexandre.belloni@bootlin.com \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=lee.jones@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-serial@vger.kernel.org \
--cc=linux-spi@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=nicolas.ferre@microchip.com \
--cc=radu.pirea@microchip.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).