Linux SPI subsystem development
 help / color / mirror / Atom feed
From: Jyothi Kumar Seerapu <jyothi.seerapu@oss.qualcomm.com>
To: Praveen Talari <praveen.talari@oss.qualcomm.com>,
	konrad.dybcio@oss.qualcomm.com, Mark Brown <broonie@kernel.org>
Cc: mukesh.savaliya@oss.qualcomm.com, linux-arm-msm@vger.kernel.org,
	linux-spi@vger.kernel.org, linux-kernel@vger.kernel.org,
	chandana.chiluveru@oss.qualcomm.com
Subject: Re: [PATCH v3 2/2] spi: qcom-geni: Add panic notifier to cancel and reset DMA during panic
Date: Fri, 21 Aug 2026 16:19:33 +0530	[thread overview]
Message-ID: <720c8c7f-532c-41e2-a4b4-60ab0edbb280@oss.qualcomm.com> (raw)
In-Reply-To: <20260818-add-shutdown-and-panic-notifier-for-spi-v3-2-8b62c4bc2d21@oss.qualcomm.com>



On 8/18/2026 6:58 PM, Praveen Talari wrote:
> When a VM crashes with an active SPI DMA transfer in progress, the
> SMMU raises context faults as the DMA engine continues to access
> IOVAs that are invalidated when the VM's memory context is torn down.
> These faults can affect other VMs sharing the same SMMU instance and
> obscure the root cause of the crash.
> 
> Register a panic notifier that cancels (or aborts, if cancel doesn't
> complete) the in-flight command and resets the TX/RX DMA FSMs, so the
> DMA engine stops issuing transactions against invalidated IOVAs
> before the system halts. For GPI DMA mode, the DMA channels are
> terminated directly via dmaengine_terminate_async().
> 
> The notifier bails out early if the device is not runtime-active or
> if there's no active GENI command, avoiding unnecessary register
> accesses while the SE is clock-gated or idle.
> 
> Since panic notifiers run with IRQs and preemption disabled,
> completion-based waits used by the regular error-handling path
> (handle_se_timeout()) cannot be reused here. Instead, the relevant
> status registers are polled directly with
> readl_poll_timeout_atomic(), which is safe to call in this context.
> 
> Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
> ---
>   drivers/spi/spi-geni-qcom.c | 68 +++++++++++++++++++++++++++++++++++++++++++++
>   1 file changed, 68 insertions(+)
> 
> diff --git a/drivers/spi/spi-geni-qcom.c b/drivers/spi/spi-geni-qcom.c
> index c65c1788325d..f272bd0cb640 100644
> --- a/drivers/spi/spi-geni-qcom.c
> +++ b/drivers/spi/spi-geni-qcom.c
> @@ -12,8 +12,10 @@
>   #include <linux/dma/qcom-gpi-dma.h>
>   #include <linux/interrupt.h>
>   #include <linux/io.h>
> +#include <linux/iopoll.h>
>   #include <linux/log2.h>
>   #include <linux/module.h>
> +#include <linux/panic_notifier.h>
>   #include <linux/platform_device.h>
>   #include <linux/pm_opp.h>
>   #include <linux/pm_runtime.h>
> @@ -115,6 +117,7 @@ struct spi_geni_master {
>   	struct dma_chan *rx;
>   	int cur_xfer_mode;
>   	const struct geni_spi_desc *dev_data;
> +	struct notifier_block panic_nb;
>   };
>   
>   static void spi_slv_setup(struct spi_geni_master *mas)
> @@ -1073,6 +1076,62 @@ static void spi_geni_shutdown(struct platform_device *pdev)
>   	spi_controller_suspend(spi);
>   }
>   
> +static int spi_geni_panic_notifier(struct notifier_block *nb,
> +				   unsigned long action, void *data)
> +{
> +	struct spi_geni_master *mas = container_of(nb, struct spi_geni_master, panic_nb);
> +	struct spi_controller *spi = dev_get_drvdata(mas->dev);
> +	struct geni_se *se = &mas->se;
> +	u32 val;
> +
> +	if (!pm_runtime_active(mas->dev))
> +		return NOTIFY_OK;
> +
> +	if (mas->cur_xfer_mode == GENI_GPI_DMA) {
> +		dmaengine_terminate_async(mas->tx);
> +		dmaengine_terminate_async(mas->rx);
> +		return NOTIFY_OK;
> +	}
> +
> +	if (!(readl_relaxed(se->base + SE_GENI_STATUS) & M_GENI_CMD_ACTIVE))
> +		return NOTIFY_OK;
> +
> +	if (!spi->target) {
> +		geni_se_cancel_m_cmd(se);
> +		if (!readl_poll_timeout_atomic(se->base + SE_GENI_M_IRQ_STATUS, val,
> +					       val & M_CMD_CANCEL_EN, 10, 50000)) {
> +			writel_relaxed(M_CMD_CANCEL_EN, se->base + SE_GENI_M_IRQ_CLEAR);
> +			return NOTIFY_OK;
Looks like a successful cancel here returns NOTIFY_OK directly, skipping 
the FSM reset block below it entirely. Is that the correct expectation 
?> +		}
> +	}
> +
> +	geni_se_abort_m_cmd(se);
> +	if (!readl_poll_timeout_atomic(se->base + SE_GENI_M_IRQ_STATUS, val,
> +				       val & M_CMD_ABORT_EN, 10, 50000))
> +		writel_relaxed(M_CMD_ABORT_EN, se->base + SE_GENI_M_IRQ_CLEAR);
> +
> +	if (mas->cur_xfer_mode == GENI_SE_DMA) {
> +		writel_relaxed(1, se->base + SE_DMA_TX_FSM_RST);
> +		readl_poll_timeout_atomic(se->base + SE_DMA_TX_IRQ_STAT, val,
> +					  val & TX_RESET_DONE, 10, 50000);
> +		writel_relaxed(val, se->base + SE_DMA_TX_IRQ_CLR);
> +
> +		writel_relaxed(1, se->base + SE_DMA_RX_FSM_RST);
> +		readl_poll_timeout_atomic(se->base + SE_DMA_RX_IRQ_STAT, val,
> +					  val & RX_RESET_DONE, 10, 50000);
> +		writel_relaxed(val, se->base + SE_DMA_RX_IRQ_CLR);
> +	}
> +
> +	return NOTIFY_OK;
> +}
> +
> +static void spi_geni_unregister_notifiers(void *data)
> +{
> +	struct spi_geni_master *mas = data;
> +
> +	atomic_notifier_chain_unregister(&panic_notifier_list, &mas->panic_nb);
> +}
> +
>   static int spi_geni_probe(struct platform_device *pdev)
>   {
>   	int ret, irq;
> @@ -1161,6 +1220,15 @@ static int spi_geni_probe(struct platform_device *pdev)
>   	if (ret)
>   		return ret;
>   
> +	mas->panic_nb.notifier_call = spi_geni_panic_notifier;
> +	ret = atomic_notifier_chain_register(&panic_notifier_list, &mas->panic_nb);
> +	if (ret)
> +		return ret;
> +
> +	ret = devm_add_action_or_reset(dev, spi_geni_unregister_notifiers, mas);
> +	if (ret)
> +		return ret;
> +
>   	return devm_spi_register_controller(dev, spi);
>   }
>   
> 


  parent reply	other threads:[~2026-08-21 10:49 UTC|newest]

Thread overview: 10+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-08-18 13:28 [PATCH v3 0/2] spi: qcom-geni: Add shutdown and panic notifier support Praveen Talari
2026-08-18 13:28 ` [PATCH v3 1/2] spi: qcom-geni: Add shutdown callback to quiesce hardware on reboot Praveen Talari
2026-08-19 18:46   ` Mukesh Savaliya
2026-08-21 10:29   ` Jyothi Kumar Seerapu
2026-08-21 15:56     ` Praveen Talari
2026-08-18 13:28 ` [PATCH v3 2/2] spi: qcom-geni: Add panic notifier to cancel and reset DMA during panic Praveen Talari
2026-08-19 19:32   ` Mukesh Savaliya
2026-08-21  9:55     ` Praveen Talari
2026-08-21 10:49   ` Jyothi Kumar Seerapu [this message]
2026-08-21 15:51     ` Praveen Talari

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=720c8c7f-532c-41e2-a4b4-60ab0edbb280@oss.qualcomm.com \
    --to=jyothi.seerapu@oss.qualcomm.com \
    --cc=broonie@kernel.org \
    --cc=chandana.chiluveru@oss.qualcomm.com \
    --cc=konrad.dybcio@oss.qualcomm.com \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-spi@vger.kernel.org \
    --cc=mukesh.savaliya@oss.qualcomm.com \
    --cc=praveen.talari@oss.qualcomm.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox