[PATCH 00/28] Blackfin SPI updates for 2.6.36

[PATCH 00/28] Blackfin SPI updates for 2.6.36

[Mike Frysinger]

Quite a bit here, but these patches have been around for a while.  The
reason they haven't been pushed up before was that some of the first
changes introduced known bugs themselves and needed some manual fixing.

Also, while some files touch Blackfin headers in arch/blackfin/, I'd
like to keep them in this series and merge through the SPI tree to keep
conflict issues down, as well as possible breakage due to desync.

These are also available in my 'for-spi' branch of my git tree:
	git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin.git

Barry Song (6):
  Blackfin SPI: fix CS handling
  Blackfin SPI: redo GPIO CS handling
  Blackfin SPI: save/restore state when suspending/resuming
  Blackfin SPI: sync hardware state before reprogramming everything
  Blackfin SPI: use dma_disable_irq_nosync() in irq handler
  Blackfin SPI: warn when CS is driven by hardware (CPHA=0)

Bob Liu (1):
  Blackfin SPI: check per-transfer bits_per_word

Daniel Mack (1):
  Blackfin SPI: fix resources leakage

Michael Hennerich (1):
  Blackfin SPI: init early

Mike Frysinger (13):
  Blackfin SPI: drop custom cs_change_per_word support
  Blackfin SPI: punt useless null read/write funcs
  Blackfin SPI: fix up some unused/misleading comments
  Blackfin SPI: convert queue run state to true/false
  Blackfin SPI: convert read/write/duplex funcs to a dedicated ops
    structure
  Blackfin SPI: convert struct names to something more logical
  Blackfin SPI: drop extra memory we don't need
  Blackfin SPI: use the SPI namespaced bit names
  Blackfin: SPI: expand SPI bitmasks
  Blackfin SPI: push all size checks into the transfer function
  Blackfin SPI: reset ctl_reg bits when setup is run again on a device
  Blackfin SPI: combine duplicate SPI_CTL read/write logic
  Blackfin SPI: reject unsupported SPI modes

Rob Maris (2):
  Blackfin SPI: fix typo in comment
  Blackfin SPI: cs should be always low when a new transfer begins

Sonic Zhang (1):
  Blackfin SPI: work around anomaly 05000119

Wolfgang Muees (1):
  Blackfin SPI: force sane master-mode state at boot

Yi Li (2):
  Blackfin SPI: utilize the SPI interrupt in PIO mode
  Blackfin SPI: use nosync when disabling the IRQ from the IRQ handler

 arch/blackfin/include/asm/bfin5xx_spi.h |   81 +---
 drivers/spi/spi_bfin5xx.c               |  839 ++++++++++++++++---------------
 2 files changed, 441 insertions(+), 479 deletions(-)

-- 
1.7.3.1

[PATCH 01/28] Blackfin SPI: fix resources leakage

[Mike Frysinger]

From: Daniel Mack <daniel-rDUAYElUppE@public.gmane.org>

Re-order setup() a bit so we don't leak memory/dma/gpio resources upon
errors.  Also make sure we don't call kfree() twice on the same object.

Signed-off-by: Daniel Mack <daniel-rDUAYElUppE@public.gmane.org>
Signed-off-by: Bryan Wu <cooloney-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Signed-off-by: Yi Li <yi.li-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |  120 ++++++++++++++++++++++++++++-----------------
 1 files changed, 75 insertions(+), 45 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index 10a6dc3..4f20b92 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -1006,20 +1006,24 @@ static u16 ssel[][MAX_SPI_SSEL] = {
 /* first setup for new devices */
 static int bfin_spi_setup(struct spi_device *spi)
 {
-	struct bfin5xx_spi_chip *chip_info = NULL;
-	struct chip_data *chip;
+	struct bfin5xx_spi_chip *chip_info;
+	struct chip_data *chip = NULL;
 	struct driver_data *drv_data = spi_master_get_devdata(spi->master);
-	int ret;
+	int ret = -EINVAL;
 
 	if (spi->bits_per_word != 8 && spi->bits_per_word != 16)
-		return -EINVAL;
+		goto error;
 
 	/* Only alloc (or use chip_info) on first setup */
+	chip_info = NULL;
 	chip = spi_get_ctldata(spi);
 	if (chip == NULL) {
-		chip = kzalloc(sizeof(struct chip_data), GFP_KERNEL);
-		if (!chip)
-			return -ENOMEM;
+		chip = kzalloc(sizeof(*chip), GFP_KERNEL);
+		if (!chip) {
+			dev_err(&spi->dev, "cannot allocate chip data\n");
+			ret = -ENOMEM;
+			goto error;
+		}
 
 		chip->enable_dma = 0;
 		chip_info = spi->controller_data;
@@ -1036,7 +1040,7 @@ static int bfin_spi_setup(struct spi_device *spi)
 		if (chip_info->ctl_reg & (SPE|MSTR|CPOL|CPHA|LSBF|SIZE)) {
 			dev_err(&spi->dev, "do not set bits in ctl_reg "
 				"that the SPI framework manages\n");
-			return -EINVAL;
+			goto error;
 		}
 
 		chip->enable_dma = chip_info->enable_dma != 0
@@ -1060,26 +1064,6 @@ static int bfin_spi_setup(struct spi_device *spi)
 	chip->ctl_reg |= MSTR;
 
 	/*
-	 * if any one SPI chip is registered and wants DMA, request the
-	 * DMA channel for it
-	 */
-	if (chip->enable_dma && !drv_data->dma_requested) {
-		/* register dma irq handler */
-		if (request_dma(drv_data->dma_channel, "BFIN_SPI_DMA") < 0) {
-			dev_dbg(&spi->dev,
-				"Unable to request BlackFin SPI DMA channel\n");
-			return -ENODEV;
-		}
-		if (set_dma_callback(drv_data->dma_channel,
-		    bfin_spi_dma_irq_handler, drv_data) < 0) {
-			dev_dbg(&spi->dev, "Unable to set dma callback\n");
-			return -EPERM;
-		}
-		dma_disable_irq(drv_data->dma_channel);
-		drv_data->dma_requested = 1;
-	}
-
-	/*
 	 * Notice: for blackfin, the speed_hz is the value of register
 	 * SPI_BAUD, not the real baudrate
 	 */
@@ -1087,16 +1071,6 @@ static int bfin_spi_setup(struct spi_device *spi)
 	chip->flag = 1 << (spi->chip_select);
 	chip->chip_select_num = spi->chip_select;
 
-	if (chip->chip_select_num == 0) {
-		ret = gpio_request(chip->cs_gpio, spi->modalias);
-		if (ret) {
-			if (drv_data->dma_requested)
-				free_dma(drv_data->dma_channel);
-			return ret;
-		}
-		gpio_direction_output(chip->cs_gpio, 1);
-	}
-
 	switch (chip->bits_per_word) {
 	case 8:
 		chip->n_bytes = 1;
@@ -1123,9 +1097,39 @@ static int bfin_spi_setup(struct spi_device *spi)
 	default:
 		dev_err(&spi->dev, "%d bits_per_word is not supported\n",
 				chip->bits_per_word);
-		if (chip_info)
-			kfree(chip);
-		return -ENODEV;
+		goto error;
+	}
+
+	/*
+	 * if any one SPI chip is registered and wants DMA, request the
+	 * DMA channel for it
+	 */
+	if (chip->enable_dma && !drv_data->dma_requested) {
+		/* register dma irq handler */
+		ret = request_dma(drv_data->dma_channel, "BFIN_SPI_DMA");
+		if (ret) {
+			dev_err(&spi->dev,
+				"Unable to request BlackFin SPI DMA channel\n");
+			goto error;
+		}
+		drv_data->dma_requested = 1;
+
+		ret = set_dma_callback(drv_data->dma_channel,
+			bfin_spi_dma_irq_handler, drv_data);
+		if (ret) {
+			dev_err(&spi->dev, "Unable to set dma callback\n");
+			goto error;
+		}
+		dma_disable_irq(drv_data->dma_channel);
+	}
+
+	if (chip->chip_select_num == 0) {
+		ret = gpio_request(chip->cs_gpio, spi->modalias);
+		if (ret) {
+			dev_err(&spi->dev, "gpio_request() error\n");
+			goto pin_error;
+		}
+		gpio_direction_output(chip->cs_gpio, 1);
 	}
 
 	dev_dbg(&spi->dev, "setup spi chip %s, width is %d, dma is %d\n",
@@ -1136,14 +1140,38 @@ static int bfin_spi_setup(struct spi_device *spi)
 	spi_set_ctldata(spi, chip);
 
 	dev_dbg(&spi->dev, "chip select number is %d\n", chip->chip_select_num);
-	if ((chip->chip_select_num > 0)
-		&& (chip->chip_select_num <= spi->master->num_chipselect))
-		peripheral_request(ssel[spi->master->bus_num]
-			[chip->chip_select_num-1], spi->modalias);
+	if (chip->chip_select_num > 0 &&
+	    chip->chip_select_num <= spi->master->num_chipselect) {
+		ret = peripheral_request(ssel[spi->master->bus_num]
+		                         [chip->chip_select_num-1], spi->modalias);
+		if (ret) {
+			dev_err(&spi->dev, "peripheral_request() error\n");
+			goto pin_error;
+		}
+	}
 
 	bfin_spi_cs_deactive(drv_data, chip);
 
 	return 0;
+
+ pin_error:
+	if (chip->chip_select_num == 0)
+		gpio_free(chip->cs_gpio);
+	else
+		peripheral_free(ssel[spi->master->bus_num]
+			[chip->chip_select_num - 1]);
+ error:
+	if (chip) {
+		if (drv_data->dma_requested)
+			free_dma(drv_data->dma_channel);
+		drv_data->dma_requested = 0;
+
+		kfree(chip);
+		/* prevent free 'chip' twice */
+		spi_set_ctldata(spi, NULL);
+	}
+
+	return ret;
 }
 
 /*
@@ -1166,6 +1194,8 @@ static void bfin_spi_cleanup(struct spi_device *spi)
 		gpio_free(chip->cs_gpio);
 
 	kfree(chip);
+	/* prevent free 'chip' twice */
+	spi_set_ctldata(spi, NULL);
 }
 
 static inline int bfin_spi_init_queue(struct driver_data *drv_data)
-- 
1.7.3.1

[PATCH 02/28] Blackfin SPI: work around anomaly 05000119

[Mike Frysinger]

From: Sonic Zhang <sonic.zhang-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>

Anomaly 05000119 states that the DMA_RUN bit with peripherals isn't
reliable.  However, the way the driver is currently written (DMA IRQ
callback), we don't need the polling in the first place, so drop it.

Signed-off-by: Sonic Zhang <sonic.zhang-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |    4 ----
 1 files changed, 0 insertions(+), 4 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index 4f20b92..61c2ebf 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -540,10 +540,6 @@ static irqreturn_t bfin_spi_dma_irq_handler(int irq, void *dev_id)
 
 	clear_dma_irqstat(drv_data->dma_channel);
 
-	/* Wait for DMA to complete */
-	while (get_dma_curr_irqstat(drv_data->dma_channel) & DMA_RUN)
-		cpu_relax();
-
 	/*
 	 * wait for the last transaction shifted out.  HRM states:
 	 * at this point there may still be data in the SPI DMA FIFO waiting
-- 
1.7.3.1

[PATCH 03/28] Blackfin SPI: force sane master-mode state at boot

[Mike Frysinger]

From: Wolfgang Muees <wolfgang.mues-3FOdemwfcUYPyMaTEpOvjQ@public.gmane.org>

We should make sure the SPI controller is in a sane state in case the
boot loader left it in a crappy state.  Such as DMA pending which causes
interrupts to fire on us.

When setting a sane initial state, do not default to slave mode.  If we
do, then the SPI peripheral may implicitly take over the SPISS pin which
other things might be using.

For example, the BF533-STAMP uses this pin as a GPIO to control switching
between ethernet and flash.  If the SPI peripheral controls the output
state instead, the ethernet is no longer accessible.

URL: http://blackfin.uclinux.org/gf/tracker/5630
Signed-off-by: Wolfgang Muees <wolfgang.mues-3FOdemwfcUYPyMaTEpOvjQ@public.gmane.org>
Signed-off-by: Michael Hennerich <michael.hennerich-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |    6 ++++++
 1 files changed, 6 insertions(+), 0 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index 61c2ebf..b835254 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -1354,6 +1354,12 @@ static int __init bfin_spi_probe(struct platform_device *pdev)
 		goto out_error_queue_alloc;
 	}
 
+	/* Reset SPI registers. If these registers were used by the boot loader,
+	 * the sky may fall on your head if you enable the dma controller.
+	 */
+	write_CTRL(drv_data, BIT_CTL_CPHA | BIT_CTL_MASTER);
+	write_FLAG(drv_data, 0xFF00);
+
 	/* Register with the SPI framework */
 	platform_set_drvdata(pdev, drv_data);
 	status = spi_register_master(master);
-- 
1.7.3.1

[PATCH 04/28] Blackfin SPI: utilize the SPI interrupt in PIO mode

[Mike Frysinger]

From: Yi Li <yi.li-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>

The current behavior in PIO mode is to poll the SPI status registers which
can obviously lead to higher latencies when doing a lot of SPI traffic.
There is a SPI interrupt which can be used instead to signal individual
completion of transactions.

Signed-off-by: Yi Li <yi.li-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |  235 +++++++++++++++++++++++++++++++++++----------
 1 files changed, 185 insertions(+), 50 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index b835254..3736c35 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -92,6 +92,9 @@ struct driver_data {
 	dma_addr_t rx_dma;
 	dma_addr_t tx_dma;
 
+	int irq_requested;
+	int spi_irq;
+
 	size_t rx_map_len;
 	size_t tx_map_len;
 	u8 n_bytes;
@@ -115,6 +118,7 @@ struct chip_data {
 	u16 cs_chg_udelay;	/* Some devices require > 255usec delay */
 	u32 cs_gpio;
 	u16 idle_tx_val;
+	u8 pio_interrupt;	/* use spi data irq */
 	void (*write) (struct driver_data *);
 	void (*read) (struct driver_data *);
 	void (*duplex) (struct driver_data *);
@@ -525,6 +529,79 @@ static void bfin_spi_giveback(struct driver_data *drv_data)
 		msg->complete(msg->context);
 }
 
+/* spi data irq handler */
+static irqreturn_t bfin_spi_pio_irq_handler(int irq, void *dev_id)
+{
+	struct driver_data *drv_data = dev_id;
+	struct chip_data *chip = drv_data->cur_chip;
+	struct spi_message *msg = drv_data->cur_msg;
+	int n_bytes = drv_data->n_bytes;
+
+	/* wait until transfer finished. */
+	while (!(read_STAT(drv_data) & BIT_STAT_RXS))
+		cpu_relax();
+
+	if ((drv_data->tx && drv_data->tx >= drv_data->tx_end) ||
+		(drv_data->rx && drv_data->rx >= (drv_data->rx_end - n_bytes))) {
+		/* last read */
+		if (drv_data->rx) {
+			dev_dbg(&drv_data->pdev->dev, "last read\n");
+			if (n_bytes == 2)
+				*(u16 *) (drv_data->rx) = read_RDBR(drv_data);
+			else if (n_bytes == 1)
+				*(u8 *) (drv_data->rx) = read_RDBR(drv_data);
+			drv_data->rx += n_bytes;
+		}
+
+		msg->actual_length += drv_data->len_in_bytes;
+		if (drv_data->cs_change)
+			bfin_spi_cs_deactive(drv_data, chip);
+		/* Move to next transfer */
+		msg->state = bfin_spi_next_transfer(drv_data);
+
+		disable_irq(drv_data->spi_irq);
+
+		/* Schedule transfer tasklet */
+		tasklet_schedule(&drv_data->pump_transfers);
+		return IRQ_HANDLED;
+	}
+
+	if (drv_data->rx && drv_data->tx) {
+		/* duplex */
+		dev_dbg(&drv_data->pdev->dev, "duplex: write_TDBR\n");
+		if (drv_data->n_bytes == 2) {
+			*(u16 *) (drv_data->rx) = read_RDBR(drv_data);
+			write_TDBR(drv_data, (*(u16 *) (drv_data->tx)));
+		} else if (drv_data->n_bytes == 1) {
+			*(u8 *) (drv_data->rx) = read_RDBR(drv_data);
+			write_TDBR(drv_data, (*(u8 *) (drv_data->tx)));
+		}
+	} else if (drv_data->rx) {
+		/* read */
+		dev_dbg(&drv_data->pdev->dev, "read: write_TDBR\n");
+		if (drv_data->n_bytes == 2)
+			*(u16 *) (drv_data->rx) = read_RDBR(drv_data);
+		else if (drv_data->n_bytes == 1)
+			*(u8 *) (drv_data->rx) = read_RDBR(drv_data);
+		write_TDBR(drv_data, chip->idle_tx_val);
+	} else if (drv_data->tx) {
+		/* write */
+		dev_dbg(&drv_data->pdev->dev, "write: write_TDBR\n");
+		bfin_spi_dummy_read(drv_data);
+		if (drv_data->n_bytes == 2)
+			write_TDBR(drv_data, (*(u16 *) (drv_data->tx)));
+		else if (drv_data->n_bytes == 1)
+			write_TDBR(drv_data, (*(u8 *) (drv_data->tx)));
+	}
+
+	if (drv_data->tx)
+		drv_data->tx += n_bytes;
+	if (drv_data->rx)
+		drv_data->rx += n_bytes;
+
+	return IRQ_HANDLED;
+}
+
 static irqreturn_t bfin_spi_dma_irq_handler(int irq, void *dev_id)
 {
 	struct driver_data *drv_data = dev_id;
@@ -700,6 +777,7 @@ static void bfin_spi_pump_transfers(unsigned long data)
 
 	default:
 		/* No change, the same as default setting */
+		transfer->bits_per_word = chip->bits_per_word;
 		drv_data->n_bytes = chip->n_bytes;
 		width = chip->width;
 		drv_data->write = drv_data->tx ? chip->write : bfin_spi_null_writer;
@@ -842,60 +920,86 @@ static void bfin_spi_pump_transfers(unsigned long data)
 		dma_enable_irq(drv_data->dma_channel);
 		local_irq_restore(flags);
 
-	} else {
-		/* IO mode write then read */
-		dev_dbg(&drv_data->pdev->dev, "doing IO transfer\n");
+		return;
+	}
 
-		/* we always use SPI_WRITE mode. SPI_READ mode
-		   seems to have problems with setting up the
-		   output value in TDBR prior to the transfer. */
+	if (chip->pio_interrupt) {
+		/* use write mode. spi irq should have been disabled */
+		cr = (read_CTRL(drv_data) & (~BIT_CTL_TIMOD));
 		write_CTRL(drv_data, (cr | CFG_SPI_WRITE));
 
-		if (full_duplex) {
-			/* full duplex mode */
-			BUG_ON((drv_data->tx_end - drv_data->tx) !=
-			       (drv_data->rx_end - drv_data->rx));
-			dev_dbg(&drv_data->pdev->dev,
-				"IO duplex: cr is 0x%x\n", cr);
-
-			drv_data->duplex(drv_data);
-
-			if (drv_data->tx != drv_data->tx_end)
-				tranf_success = 0;
-		} else if (drv_data->tx != NULL) {
-			/* write only half duplex */
-			dev_dbg(&drv_data->pdev->dev,
-				"IO write: cr is 0x%x\n", cr);
+		/* discard old RX data and clear RXS */
+		bfin_spi_dummy_read(drv_data);
 
-			drv_data->write(drv_data);
+		/* start transfer */
+		if (drv_data->tx == NULL)
+			write_TDBR(drv_data, chip->idle_tx_val);
+		else {
+			if (transfer->bits_per_word == 8)
+				write_TDBR(drv_data, (*(u8 *) (drv_data->tx)));
+			else if (transfer->bits_per_word == 16)
+				write_TDBR(drv_data, (*(u16 *) (drv_data->tx)));
+			drv_data->tx += drv_data->n_bytes;
+		}
 
-			if (drv_data->tx != drv_data->tx_end)
-				tranf_success = 0;
-		} else if (drv_data->rx != NULL) {
-			/* read only half duplex */
-			dev_dbg(&drv_data->pdev->dev,
-				"IO read: cr is 0x%x\n", cr);
+		/* once TDBR is empty, interrupt is triggered */
+		enable_irq(drv_data->spi_irq);
+		return;
+	}
 
-			drv_data->read(drv_data);
-			if (drv_data->rx != drv_data->rx_end)
-				tranf_success = 0;
-		}
+	/* IO mode */
+	dev_dbg(&drv_data->pdev->dev, "doing IO transfer\n");
+
+	/* we always use SPI_WRITE mode. SPI_READ mode
+	   seems to have problems with setting up the
+	   output value in TDBR prior to the transfer. */
+	write_CTRL(drv_data, (cr | CFG_SPI_WRITE));
+
+	if (full_duplex) {
+		/* full duplex mode */
+		BUG_ON((drv_data->tx_end - drv_data->tx) !=
+		       (drv_data->rx_end - drv_data->rx));
+		dev_dbg(&drv_data->pdev->dev,
+			"IO duplex: cr is 0x%x\n", cr);
+
+		drv_data->duplex(drv_data);
+
+		if (drv_data->tx != drv_data->tx_end)
+			tranf_success = 0;
+	} else if (drv_data->tx != NULL) {
+		/* write only half duplex */
+		dev_dbg(&drv_data->pdev->dev,
+			"IO write: cr is 0x%x\n", cr);
+
+		drv_data->write(drv_data);
+
+		if (drv_data->tx != drv_data->tx_end)
+			tranf_success = 0;
+	} else if (drv_data->rx != NULL) {
+		/* read only half duplex */
+		dev_dbg(&drv_data->pdev->dev,
+			"IO read: cr is 0x%x\n", cr);
+
+		drv_data->read(drv_data);
+		if (drv_data->rx != drv_data->rx_end)
+			tranf_success = 0;
+	}
 
-		if (!tranf_success) {
-			dev_dbg(&drv_data->pdev->dev,
-				"IO write error!\n");
-			message->state = ERROR_STATE;
-		} else {
-			/* Update total byte transfered */
-			message->actual_length += drv_data->len_in_bytes;
-			/* Move to next transfer of this msg */
-			message->state = bfin_spi_next_transfer(drv_data);
-			if (drv_data->cs_change)
-				bfin_spi_cs_deactive(drv_data, chip);
-		}
-		/* Schedule next transfer tasklet */
-		tasklet_schedule(&drv_data->pump_transfers);
+	if (!tranf_success) {
+		dev_dbg(&drv_data->pdev->dev,
+			"IO write error!\n");
+		message->state = ERROR_STATE;
+	} else {
+		/* Update total byte transfered */
+		message->actual_length += drv_data->len_in_bytes;
+		/* Move to next transfer of this msg */
+		message->state = bfin_spi_next_transfer(drv_data);
+		if (drv_data->cs_change)
+			bfin_spi_cs_deactive(drv_data, chip);
 	}
+
+	/* Schedule next transfer tasklet */
+	tasklet_schedule(&drv_data->pump_transfers);
 }
 
 /* pop a msg from queue and kick off real transfer */
@@ -1047,6 +1151,7 @@ static int bfin_spi_setup(struct spi_device *spi)
 		chip->cs_chg_udelay = chip_info->cs_chg_udelay;
 		chip->cs_gpio = chip_info->cs_gpio;
 		chip->idle_tx_val = chip_info->idle_tx_val;
+		chip->pio_interrupt = chip_info->pio_interrupt;
 	}
 
 	/* translate common spi framework into our register */
@@ -1096,6 +1201,11 @@ static int bfin_spi_setup(struct spi_device *spi)
 		goto error;
 	}
 
+	if (chip->enable_dma && chip->pio_interrupt) {
+		dev_err(&spi->dev, "enable_dma is set, "
+				"do not set pio_interrupt\n");
+		goto error;
+	}
 	/*
 	 * if any one SPI chip is registered and wants DMA, request the
 	 * DMA channel for it
@@ -1119,6 +1229,18 @@ static int bfin_spi_setup(struct spi_device *spi)
 		dma_disable_irq(drv_data->dma_channel);
 	}
 
+	if (chip->pio_interrupt && !drv_data->irq_requested) {
+		ret = request_irq(drv_data->spi_irq, bfin_spi_pio_irq_handler,
+			IRQF_DISABLED, "BFIN_SPI", drv_data);
+		if (ret) {
+			dev_err(&spi->dev, "Unable to register spi IRQ\n");
+			goto error;
+		}
+		drv_data->irq_requested = 1;
+		/* we use write mode, spi irq has to be disabled here */
+		disable_irq(drv_data->spi_irq);
+	}
+
 	if (chip->chip_select_num == 0) {
 		ret = gpio_request(chip->cs_gpio, spi->modalias);
 		if (ret) {
@@ -1328,11 +1450,19 @@ static int __init bfin_spi_probe(struct platform_device *pdev)
 		goto out_error_ioremap;
 	}
 
-	drv_data->dma_channel = platform_get_irq(pdev, 0);
-	if (drv_data->dma_channel < 0) {
+	res = platform_get_resource(pdev, IORESOURCE_DMA, 0);
+	if (res == NULL) {
 		dev_err(dev, "No DMA channel specified\n");
 		status = -ENOENT;
-		goto out_error_no_dma_ch;
+		goto out_error_free_io;
+	}
+	drv_data->dma_channel = res->start;
+
+	drv_data->spi_irq = platform_get_irq(pdev, 0);
+	if (drv_data->spi_irq < 0) {
+		dev_err(dev, "No spi pio irq specified\n");
+		status = -ENOENT;
+		goto out_error_free_io;
 	}
 
 	/* Initial and start queue */
@@ -1375,7 +1505,7 @@ static int __init bfin_spi_probe(struct platform_device *pdev)
 
 out_error_queue_alloc:
 	bfin_spi_destroy_queue(drv_data);
-out_error_no_dma_ch:
+out_error_free_io:
 	iounmap((void *) drv_data->regs_base);
 out_error_ioremap:
 out_error_get_res:
@@ -1407,6 +1537,11 @@ static int __devexit bfin_spi_remove(struct platform_device *pdev)
 			free_dma(drv_data->dma_channel);
 	}
 
+	if (drv_data->irq_requested) {
+		free_irq(drv_data->spi_irq, drv_data);
+		drv_data->irq_requested = 0;
+	}
+
 	/* Disconnect from the SPI framework */
 	spi_unregister_master(drv_data->master);
 
-- 
1.7.3.1

[PATCH 05/28] Blackfin SPI: fix CS handling

[Mike Frysinger]

From: Barry Song <barry.song-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>

The CS helper functions were toggling both the Flag Enable and the Flag
Value bits, but the Flag Value bit is ignored if the corresponding Flag
Enable bit is cleared.  So under high speed transactions, the CS sometimes
would not toggle properly.

Since it makes no sense to toggle the Flag Enable bit dynamically when we
actually want to control the Flag Value, do this when setting up the device
and then only handle toggling of the CS value during runtime.

Signed-off-by: Barry Song <barry.song-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |   33 +++++++++++++++++++++++++++------
 1 files changed, 27 insertions(+), 6 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index 3736c35..6150a8c 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -188,8 +188,7 @@ static void bfin_spi_cs_active(struct driver_data *drv_data, struct chip_data *c
 	if (likely(chip->chip_select_num)) {
 		u16 flag = read_FLAG(drv_data);
 
-		flag |= chip->flag;
-		flag &= ~(chip->flag << 8);
+		flag &= ~chip->flag;
 
 		write_FLAG(drv_data, flag);
 	} else {
@@ -202,8 +201,7 @@ static void bfin_spi_cs_deactive(struct driver_data *drv_data, struct chip_data
 	if (likely(chip->chip_select_num)) {
 		u16 flag = read_FLAG(drv_data);
 
-		flag &= ~chip->flag;
-		flag |= (chip->flag << 8);
+		flag |= chip->flag;
 
 		write_FLAG(drv_data, flag);
 	} else {
@@ -215,6 +213,25 @@ static void bfin_spi_cs_deactive(struct driver_data *drv_data, struct chip_data
 		udelay(chip->cs_chg_udelay);
 }
 
+/* enable or disable the pin muxed by GPIO and SPI CS to work as SPI CS */
+static inline void bfin_spi_cs_enable(struct driver_data *drv_data, struct chip_data *chip)
+{
+	u16 flag = read_FLAG(drv_data);
+
+	flag |= (chip->flag >> 8);
+
+	write_FLAG(drv_data, flag);
+}
+
+static inline void bfin_spi_cs_disable(struct driver_data *drv_data, struct chip_data *chip)
+{
+	u16 flag = read_FLAG(drv_data);
+
+	flag &= ~(chip->flag >> 8);
+
+	write_FLAG(drv_data, flag);
+}
+
 /* stop controller and re-config current chip*/
 static void bfin_spi_restore_state(struct driver_data *drv_data)
 {
@@ -1169,7 +1186,7 @@ static int bfin_spi_setup(struct spi_device *spi)
 	 * SPI_BAUD, not the real baudrate
 	 */
 	chip->baud = hz_to_spi_baud(spi->max_speed_hz);
-	chip->flag = 1 << (spi->chip_select);
+	chip->flag = (1 << (spi->chip_select)) << 8;
 	chip->chip_select_num = spi->chip_select;
 
 	switch (chip->bits_per_word) {
@@ -1268,6 +1285,7 @@ static int bfin_spi_setup(struct spi_device *spi)
 		}
 	}
 
+	bfin_spi_cs_enable(drv_data, chip);
 	bfin_spi_cs_deactive(drv_data, chip);
 
 	return 0;
@@ -1299,14 +1317,17 @@ static int bfin_spi_setup(struct spi_device *spi)
 static void bfin_spi_cleanup(struct spi_device *spi)
 {
 	struct chip_data *chip = spi_get_ctldata(spi);
+	struct driver_data *drv_data = spi_master_get_devdata(spi->master);
 
 	if (!chip)
 		return;
 
 	if ((chip->chip_select_num > 0)
-		&& (chip->chip_select_num <= spi->master->num_chipselect))
+		&& (chip->chip_select_num <= spi->master->num_chipselect)) {
 		peripheral_free(ssel[spi->master->bus_num]
 					[chip->chip_select_num-1]);
+		bfin_spi_cs_disable(drv_data, chip);
+	}
 
 	if (chip->chip_select_num == 0)
 		gpio_free(chip->cs_gpio);
-- 
1.7.3.1

[PATCH 06/28] Blackfin SPI: drop custom cs_change_per_word support

[Mike Frysinger]

As David points out, the cs_change_per_word option isn't standard, nor is
anyone actually using it.  So punt all of the dead code considering it
makes up ~10% of the code size.

Reported-by: David Brownell <dbrownell-Rn4VEauK+AKRv+LV9MX5uipxlwaOVQ5f@public.gmane.org>
Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 arch/blackfin/include/asm/bfin5xx_spi.h |    1 -
 drivers/spi/spi_bfin5xx.c               |  148 +++----------------------------
 2 files changed, 12 insertions(+), 137 deletions(-)

diff --git a/arch/blackfin/include/asm/bfin5xx_spi.h b/arch/blackfin/include/asm/bfin5xx_spi.h
index ed4f8c6..ee3ecb9 100644
--- a/arch/blackfin/include/asm/bfin5xx_spi.h
+++ b/arch/blackfin/include/asm/bfin5xx_spi.h
@@ -120,7 +120,6 @@ struct bfin5xx_spi_chip {
 	u16 ctl_reg;
 	u8 enable_dma;
 	u8 bits_per_word;
-	u8 cs_change_per_word;
 	u16 cs_chg_udelay; /* Some devices require 16-bit delays */
 	u32 cs_gpio;
 	/* Value to send if no TX value is supplied, usually 0x0 or 0xFFFF */
diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index 6150a8c..f4023a7 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -114,7 +114,6 @@ struct chip_data {
 	u8 width;		/* 0 or 1 */
 	u8 enable_dma;
 	u8 bits_per_word;	/* 8 or 16 */
-	u8 cs_change_per_word;
 	u16 cs_chg_udelay;	/* Some devices require > 255usec delay */
 	u32 cs_gpio;
 	u16 idle_tx_val;
@@ -309,24 +308,6 @@ static void bfin_spi_u8_writer(struct driver_data *drv_data)
 	}
 }
 
-static void bfin_spi_u8_cs_chg_writer(struct driver_data *drv_data)
-{
-	struct chip_data *chip = drv_data->cur_chip;
-
-	/* clear RXS (we check for RXS inside the loop) */
-	bfin_spi_dummy_read(drv_data);
-
-	while (drv_data->tx < drv_data->tx_end) {
-		bfin_spi_cs_active(drv_data, chip);
-		write_TDBR(drv_data, (*(u8 *) (drv_data->tx++)));
-		/* make sure transfer finished before deactiving CS */
-		while (!(read_STAT(drv_data) & BIT_STAT_RXS))
-			cpu_relax();
-		bfin_spi_dummy_read(drv_data);
-		bfin_spi_cs_deactive(drv_data, chip);
-	}
-}
-
 static void bfin_spi_u8_reader(struct driver_data *drv_data)
 {
 	u16 tx_val = drv_data->cur_chip->idle_tx_val;
@@ -342,24 +323,6 @@ static void bfin_spi_u8_reader(struct driver_data *drv_data)
 	}
 }
 
-static void bfin_spi_u8_cs_chg_reader(struct driver_data *drv_data)
-{
-	struct chip_data *chip = drv_data->cur_chip;
-	u16 tx_val = chip->idle_tx_val;
-
-	/* discard old RX data and clear RXS */
-	bfin_spi_dummy_read(drv_data);
-
-	while (drv_data->rx < drv_data->rx_end) {
-		bfin_spi_cs_active(drv_data, chip);
-		write_TDBR(drv_data, tx_val);
-		while (!(read_STAT(drv_data) & BIT_STAT_RXS))
-			cpu_relax();
-		*(u8 *) (drv_data->rx++) = read_RDBR(drv_data);
-		bfin_spi_cs_deactive(drv_data, chip);
-	}
-}
-
 static void bfin_spi_u8_duplex(struct driver_data *drv_data)
 {
 	/* discard old RX data and clear RXS */
@@ -373,23 +336,6 @@ static void bfin_spi_u8_duplex(struct driver_data *drv_data)
 	}
 }
 
-static void bfin_spi_u8_cs_chg_duplex(struct driver_data *drv_data)
-{
-	struct chip_data *chip = drv_data->cur_chip;
-
-	/* discard old RX data and clear RXS */
-	bfin_spi_dummy_read(drv_data);
-
-	while (drv_data->rx < drv_data->rx_end) {
-		bfin_spi_cs_active(drv_data, chip);
-		write_TDBR(drv_data, (*(u8 *) (drv_data->tx++)));
-		while (!(read_STAT(drv_data) & BIT_STAT_RXS))
-			cpu_relax();
-		*(u8 *) (drv_data->rx++) = read_RDBR(drv_data);
-		bfin_spi_cs_deactive(drv_data, chip);
-	}
-}
-
 static void bfin_spi_u16_writer(struct driver_data *drv_data)
 {
 	/* clear RXS (we check for RXS inside the loop) */
@@ -407,25 +353,6 @@ static void bfin_spi_u16_writer(struct driver_data *drv_data)
 	}
 }
 
-static void bfin_spi_u16_cs_chg_writer(struct driver_data *drv_data)
-{
-	struct chip_data *chip = drv_data->cur_chip;
-
-	/* clear RXS (we check for RXS inside the loop) */
-	bfin_spi_dummy_read(drv_data);
-
-	while (drv_data->tx < drv_data->tx_end) {
-		bfin_spi_cs_active(drv_data, chip);
-		write_TDBR(drv_data, (*(u16 *) (drv_data->tx)));
-		drv_data->tx += 2;
-		/* make sure transfer finished before deactiving CS */
-		while (!(read_STAT(drv_data) & BIT_STAT_RXS))
-			cpu_relax();
-		bfin_spi_dummy_read(drv_data);
-		bfin_spi_cs_deactive(drv_data, chip);
-	}
-}
-
 static void bfin_spi_u16_reader(struct driver_data *drv_data)
 {
 	u16 tx_val = drv_data->cur_chip->idle_tx_val;
@@ -442,25 +369,6 @@ static void bfin_spi_u16_reader(struct driver_data *drv_data)
 	}
 }
 
-static void bfin_spi_u16_cs_chg_reader(struct driver_data *drv_data)
-{
-	struct chip_data *chip = drv_data->cur_chip;
-	u16 tx_val = chip->idle_tx_val;
-
-	/* discard old RX data and clear RXS */
-	bfin_spi_dummy_read(drv_data);
-
-	while (drv_data->rx < drv_data->rx_end) {
-		bfin_spi_cs_active(drv_data, chip);
-		write_TDBR(drv_data, tx_val);
-		while (!(read_STAT(drv_data) & BIT_STAT_RXS))
-			cpu_relax();
-		*(u16 *) (drv_data->rx) = read_RDBR(drv_data);
-		drv_data->rx += 2;
-		bfin_spi_cs_deactive(drv_data, chip);
-	}
-}
-
 static void bfin_spi_u16_duplex(struct driver_data *drv_data)
 {
 	/* discard old RX data and clear RXS */
@@ -476,25 +384,6 @@ static void bfin_spi_u16_duplex(struct driver_data *drv_data)
 	}
 }
 
-static void bfin_spi_u16_cs_chg_duplex(struct driver_data *drv_data)
-{
-	struct chip_data *chip = drv_data->cur_chip;
-
-	/* discard old RX data and clear RXS */
-	bfin_spi_dummy_read(drv_data);
-
-	while (drv_data->rx < drv_data->rx_end) {
-		bfin_spi_cs_active(drv_data, chip);
-		write_TDBR(drv_data, (*(u16 *) (drv_data->tx)));
-		drv_data->tx += 2;
-		while (!(read_STAT(drv_data) & BIT_STAT_RXS))
-			cpu_relax();
-		*(u16 *) (drv_data->rx) = read_RDBR(drv_data);
-		drv_data->rx += 2;
-		bfin_spi_cs_deactive(drv_data, chip);
-	}
-}
-
 /* test if ther is more transfer to be done */
 static void *bfin_spi_next_transfer(struct driver_data *drv_data)
 {
@@ -773,23 +662,17 @@ static void bfin_spi_pump_transfers(unsigned long data)
 	case 8:
 		drv_data->n_bytes = 1;
 		width = CFG_SPI_WORDSIZE8;
-		drv_data->read = chip->cs_change_per_word ?
-			bfin_spi_u8_cs_chg_reader : bfin_spi_u8_reader;
-		drv_data->write = chip->cs_change_per_word ?
-			bfin_spi_u8_cs_chg_writer : bfin_spi_u8_writer;
-		drv_data->duplex = chip->cs_change_per_word ?
-			bfin_spi_u8_cs_chg_duplex : bfin_spi_u8_duplex;
+		drv_data->read = bfin_spi_u8_reader;
+		drv_data->write = bfin_spi_u8_writer;
+		drv_data->duplex = bfin_spi_u8_duplex;
 		break;
 
 	case 16:
 		drv_data->n_bytes = 2;
 		width = CFG_SPI_WORDSIZE16;
-		drv_data->read = chip->cs_change_per_word ?
-			bfin_spi_u16_cs_chg_reader : bfin_spi_u16_reader;
-		drv_data->write = chip->cs_change_per_word ?
-			bfin_spi_u16_cs_chg_writer : bfin_spi_u16_writer;
-		drv_data->duplex = chip->cs_change_per_word ?
-			bfin_spi_u16_cs_chg_duplex : bfin_spi_u16_duplex;
+		drv_data->read = bfin_spi_u16_reader;
+		drv_data->write = bfin_spi_u16_writer;
+		drv_data->duplex = bfin_spi_u16_duplex;
 		break;
 
 	default:
@@ -1164,7 +1047,6 @@ static int bfin_spi_setup(struct spi_device *spi)
 		    && drv_data->master_info->enable_dma;
 		chip->ctl_reg = chip_info->ctl_reg;
 		chip->bits_per_word = chip_info->bits_per_word;
-		chip->cs_change_per_word = chip_info->cs_change_per_word;
 		chip->cs_chg_udelay = chip_info->cs_chg_udelay;
 		chip->cs_gpio = chip_info->cs_gpio;
 		chip->idle_tx_val = chip_info->idle_tx_val;
@@ -1193,23 +1075,17 @@ static int bfin_spi_setup(struct spi_device *spi)
 	case 8:
 		chip->n_bytes = 1;
 		chip->width = CFG_SPI_WORDSIZE8;
-		chip->read = chip->cs_change_per_word ?
-			bfin_spi_u8_cs_chg_reader : bfin_spi_u8_reader;
-		chip->write = chip->cs_change_per_word ?
-			bfin_spi_u8_cs_chg_writer : bfin_spi_u8_writer;
-		chip->duplex = chip->cs_change_per_word ?
-			bfin_spi_u8_cs_chg_duplex : bfin_spi_u8_duplex;
+		chip->read = bfin_spi_u8_reader;
+		chip->write = bfin_spi_u8_writer;
+		chip->duplex = bfin_spi_u8_duplex;
 		break;
 
 	case 16:
 		chip->n_bytes = 2;
 		chip->width = CFG_SPI_WORDSIZE16;
-		chip->read = chip->cs_change_per_word ?
-			bfin_spi_u16_cs_chg_reader : bfin_spi_u16_reader;
-		chip->write = chip->cs_change_per_word ?
-			bfin_spi_u16_cs_chg_writer : bfin_spi_u16_writer;
-		chip->duplex = chip->cs_change_per_word ?
-			bfin_spi_u16_cs_chg_duplex : bfin_spi_u16_duplex;
+		chip->read = bfin_spi_u16_reader;
+		chip->write = bfin_spi_u16_writer;
+		chip->duplex = bfin_spi_u16_duplex;
 		break;
 
 	default:
-- 
1.7.3.1

[PATCH 07/28] Blackfin SPI: punt useless null read/write funcs

[Mike Frysinger]

The chip ops should always be initialized, so having null fallback
functions are useless.

Reported-by: David Brownell <dbrownell-Rn4VEauK+AKRv+LV9MX5uipxlwaOVQ5f@public.gmane.org>
Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |   47 ++++----------------------------------------
 1 files changed, 5 insertions(+), 42 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index f4023a7..5e07f49 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -255,43 +255,6 @@ static inline void bfin_spi_dummy_read(struct driver_data *drv_data)
 	(void) read_RDBR(drv_data);
 }
 
-static void bfin_spi_null_writer(struct driver_data *drv_data)
-{
-	u8 n_bytes = drv_data->n_bytes;
-	u16 tx_val = drv_data->cur_chip->idle_tx_val;
-
-	/* clear RXS (we check for RXS inside the loop) */
-	bfin_spi_dummy_read(drv_data);
-
-	while (drv_data->tx < drv_data->tx_end) {
-		write_TDBR(drv_data, tx_val);
-		drv_data->tx += n_bytes;
-		/* wait until transfer finished.
-		   checking SPIF or TXS may not guarantee transfer completion */
-		while (!(read_STAT(drv_data) & BIT_STAT_RXS))
-			cpu_relax();
-		/* discard RX data and clear RXS */
-		bfin_spi_dummy_read(drv_data);
-	}
-}
-
-static void bfin_spi_null_reader(struct driver_data *drv_data)
-{
-	u8 n_bytes = drv_data->n_bytes;
-	u16 tx_val = drv_data->cur_chip->idle_tx_val;
-
-	/* discard old RX data and clear RXS */
-	bfin_spi_dummy_read(drv_data);
-
-	while (drv_data->rx < drv_data->rx_end) {
-		write_TDBR(drv_data, tx_val);
-		drv_data->rx += n_bytes;
-		while (!(read_STAT(drv_data) & BIT_STAT_RXS))
-			cpu_relax();
-		bfin_spi_dummy_read(drv_data);
-	}
-}
-
 static void bfin_spi_u8_writer(struct driver_data *drv_data)
 {
 	/* clear RXS (we check for RXS inside the loop) */
@@ -680,9 +643,9 @@ static void bfin_spi_pump_transfers(unsigned long data)
 		transfer->bits_per_word = chip->bits_per_word;
 		drv_data->n_bytes = chip->n_bytes;
 		width = chip->width;
-		drv_data->write = drv_data->tx ? chip->write : bfin_spi_null_writer;
-		drv_data->read = drv_data->rx ? chip->read : bfin_spi_null_reader;
-		drv_data->duplex = chip->duplex ? chip->duplex : bfin_spi_null_writer;
+		drv_data->write = chip->write;
+		drv_data->read = chip->read;
+		drv_data->duplex = chip->duplex;
 		break;
 	}
 	cr = (read_CTRL(drv_data) & (~BIT_CTL_TIMOD));
@@ -695,8 +658,8 @@ static void bfin_spi_pump_transfers(unsigned long data)
 		drv_data->len = transfer->len;
 	}
 	dev_dbg(&drv_data->pdev->dev,
-		"transfer: drv_data->write is %p, chip->write is %p, null_wr is %p\n",
-		drv_data->write, chip->write, bfin_spi_null_writer);
+		"transfer: drv_data->write is %p, chip->write is %p\n",
+		drv_data->write, chip->write);
 
 	/* speed and width has been set on per message */
 	message->state = RUNNING_STATE;
-- 
1.7.3.1

[PATCH 08/28] Blackfin SPI: fix up some unused/misleading comments

[Mike Frysinger]

Reported-by: David Brownell <dbrownell-Rn4VEauK+AKRv+LV9MX5uipxlwaOVQ5f@public.gmane.org>
Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |    8 ++------
 1 files changed, 2 insertions(+), 6 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index 5e07f49..045c82a 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -44,9 +44,6 @@ MODULE_LICENSE("GPL");
 #define QUEUE_RUNNING	0
 #define QUEUE_STOPPED	1
 
-/* Value to send if no TX value is supplied */
-#define SPI_IDLE_TXVAL 0x0000
-
 struct driver_data {
 	/* Driver model hookup */
 	struct platform_device *pdev;
@@ -581,7 +578,7 @@ static void bfin_spi_pump_transfers(unsigned long data)
 			udelay(previous->delay_usecs);
 	}
 
-	/* Setup the transfer state based on the type of transfer */
+	/* Flush any existing transfers that may be sitting in the hardware */
 	if (bfin_spi_flush(drv_data) == 0) {
 		dev_err(&drv_data->pdev->dev, "pump_transfers: flush failed\n");
 		message->status = -EIO;
@@ -661,7 +658,6 @@ static void bfin_spi_pump_transfers(unsigned long data)
 		"transfer: drv_data->write is %p, chip->write is %p\n",
 		drv_data->write, chip->write);
 
-	/* speed and width has been set on per message */
 	message->state = RUNNING_STATE;
 	dma_config = 0;
 
@@ -966,7 +962,7 @@ static u16 ssel[][MAX_SPI_SSEL] = {
 	P_SPI2_SSEL6, P_SPI2_SSEL7},
 };
 
-/* first setup for new devices */
+/* setup for devices (may be called multiple times -- not just first setup) */
 static int bfin_spi_setup(struct spi_device *spi)
 {
 	struct bfin5xx_spi_chip *chip_info;
-- 
1.7.3.1

[PATCH 09/28] Blackfin SPI: convert queue run state to true/false

[Mike Frysinger]

No point in creating our own version of true/false defines when there is
already a standard stdbool available to us.

Reported-by: David Brownell <dbrownell-Rn4VEauK+AKRv+LV9MX5uipxlwaOVQ5f@public.gmane.org>
Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |   18 ++++++++----------
 1 files changed, 8 insertions(+), 10 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index 045c82a..40d9f64 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -41,8 +41,6 @@ MODULE_LICENSE("GPL");
 #define RUNNING_STATE	((void *)1)
 #define DONE_STATE	((void *)2)
 #define ERROR_STATE	((void *)-1)
-#define QUEUE_RUNNING	0
-#define QUEUE_STOPPED	1
 
 struct driver_data {
 	/* Driver model hookup */
@@ -66,7 +64,7 @@ struct driver_data {
 	spinlock_t lock;
 	struct list_head queue;
 	int busy;
-	int run;
+	bool running;
 
 	/* Message Transfer pump */
 	struct tasklet_struct pump_transfers;
@@ -871,7 +869,7 @@ static void bfin_spi_pump_messages(struct work_struct *work)
 
 	/* Lock queue and check for queue work */
 	spin_lock_irqsave(&drv_data->lock, flags);
-	if (list_empty(&drv_data->queue) || drv_data->run == QUEUE_STOPPED) {
+	if (list_empty(&drv_data->queue) || !drv_data->running) {
 		/* pumper kicked off but no work to do */
 		drv_data->busy = 0;
 		spin_unlock_irqrestore(&drv_data->lock, flags);
@@ -926,7 +924,7 @@ static int bfin_spi_transfer(struct spi_device *spi, struct spi_message *msg)
 
 	spin_lock_irqsave(&drv_data->lock, flags);
 
-	if (drv_data->run == QUEUE_STOPPED) {
+	if (!drv_data->running) {
 		spin_unlock_irqrestore(&drv_data->lock, flags);
 		return -ESHUTDOWN;
 	}
@@ -938,7 +936,7 @@ static int bfin_spi_transfer(struct spi_device *spi, struct spi_message *msg)
 	dev_dbg(&spi->dev, "adding an msg in transfer() \n");
 	list_add_tail(&msg->queue, &drv_data->queue);
 
-	if (drv_data->run == QUEUE_RUNNING && !drv_data->busy)
+	if (drv_data->running && !drv_data->busy)
 		queue_work(drv_data->workqueue, &drv_data->pump_messages);
 
 	spin_unlock_irqrestore(&drv_data->lock, flags);
@@ -1177,7 +1175,7 @@ static inline int bfin_spi_init_queue(struct driver_data *drv_data)
 	INIT_LIST_HEAD(&drv_data->queue);
 	spin_lock_init(&drv_data->lock);
 
-	drv_data->run = QUEUE_STOPPED;
+	drv_data->running = false;
 	drv_data->busy = 0;
 
 	/* init transfer tasklet */
@@ -1200,12 +1198,12 @@ static inline int bfin_spi_start_queue(struct driver_data *drv_data)
 
 	spin_lock_irqsave(&drv_data->lock, flags);
 
-	if (drv_data->run == QUEUE_RUNNING || drv_data->busy) {
+	if (drv_data->running || drv_data->busy) {
 		spin_unlock_irqrestore(&drv_data->lock, flags);
 		return -EBUSY;
 	}
 
-	drv_data->run = QUEUE_RUNNING;
+	drv_data->running = true;
 	drv_data->cur_msg = NULL;
 	drv_data->cur_transfer = NULL;
 	drv_data->cur_chip = NULL;
@@ -1230,7 +1228,7 @@ static inline int bfin_spi_stop_queue(struct driver_data *drv_data)
 	 * execution path (pump_messages) would be required to call wake_up or
 	 * friends on every SPI message. Do this instead
 	 */
-	drv_data->run = QUEUE_STOPPED;
+	drv_data->running = false;
 	while (!list_empty(&drv_data->queue) && drv_data->busy && limit--) {
 		spin_unlock_irqrestore(&drv_data->lock, flags);
 		msleep(10);
-- 
1.7.3.1

[PATCH 10/28] Blackfin SPI: convert read/write/duplex funcs to a dedicated ops structure

[Mike Frysinger]

Rather than having to look up the same 3 sets of functions at the same
time, just use an ops structure so we only need to set one pointer.

Reported-by: David Brownell <dbrownell-Rn4VEauK+AKRv+LV9MX5uipxlwaOVQ5f@public.gmane.org>
Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |   58 ++++++++++++++++++++++++--------------------
 1 files changed, 32 insertions(+), 26 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index 40d9f64..b0de61a 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -42,6 +42,14 @@ MODULE_LICENSE("GPL");
 #define DONE_STATE	((void *)2)
 #define ERROR_STATE	((void *)-1)
 
+struct driver_data;
+
+struct transfer_ops {
+	void (*write) (struct driver_data *);
+	void (*read) (struct driver_data *);
+	void (*duplex) (struct driver_data *);
+};
+
 struct driver_data {
 	/* Driver model hookup */
 	struct platform_device *pdev;
@@ -94,9 +102,7 @@ struct driver_data {
 	size_t tx_map_len;
 	u8 n_bytes;
 	int cs_change;
-	void (*write) (struct driver_data *);
-	void (*read) (struct driver_data *);
-	void (*duplex) (struct driver_data *);
+	const struct transfer_ops *ops;
 };
 
 struct chip_data {
@@ -113,9 +119,7 @@ struct chip_data {
 	u32 cs_gpio;
 	u16 idle_tx_val;
 	u8 pio_interrupt;	/* use spi data irq */
-	void (*write) (struct driver_data *);
-	void (*read) (struct driver_data *);
-	void (*duplex) (struct driver_data *);
+	const struct transfer_ops *ops;
 };
 
 #define DEFINE_SPI_REG(reg, off) \
@@ -294,6 +298,12 @@ static void bfin_spi_u8_duplex(struct driver_data *drv_data)
 	}
 }
 
+static const struct transfer_ops bfin_transfer_ops_u8 = {
+	.write  = bfin_spi_u8_writer,
+	.read   = bfin_spi_u8_reader,
+	.duplex = bfin_spi_u8_duplex,
+};
+
 static void bfin_spi_u16_writer(struct driver_data *drv_data)
 {
 	/* clear RXS (we check for RXS inside the loop) */
@@ -342,6 +352,12 @@ static void bfin_spi_u16_duplex(struct driver_data *drv_data)
 	}
 }
 
+static const struct transfer_ops bfin_transfer_ops_u16 = {
+	.write  = bfin_spi_u16_writer,
+	.read   = bfin_spi_u16_reader,
+	.duplex = bfin_spi_u16_duplex,
+};
+
 /* test if ther is more transfer to be done */
 static void *bfin_spi_next_transfer(struct driver_data *drv_data)
 {
@@ -620,17 +636,13 @@ static void bfin_spi_pump_transfers(unsigned long data)
 	case 8:
 		drv_data->n_bytes = 1;
 		width = CFG_SPI_WORDSIZE8;
-		drv_data->read = bfin_spi_u8_reader;
-		drv_data->write = bfin_spi_u8_writer;
-		drv_data->duplex = bfin_spi_u8_duplex;
+		drv_data->ops = &bfin_transfer_ops_u8;
 		break;
 
 	case 16:
 		drv_data->n_bytes = 2;
 		width = CFG_SPI_WORDSIZE16;
-		drv_data->read = bfin_spi_u16_reader;
-		drv_data->write = bfin_spi_u16_writer;
-		drv_data->duplex = bfin_spi_u16_duplex;
+		drv_data->ops = &bfin_transfer_ops_u16;
 		break;
 
 	default:
@@ -638,9 +650,7 @@ static void bfin_spi_pump_transfers(unsigned long data)
 		transfer->bits_per_word = chip->bits_per_word;
 		drv_data->n_bytes = chip->n_bytes;
 		width = chip->width;
-		drv_data->write = chip->write;
-		drv_data->read = chip->read;
-		drv_data->duplex = chip->duplex;
+		drv_data->ops = chip->ops;
 		break;
 	}
 	cr = (read_CTRL(drv_data) & (~BIT_CTL_TIMOD));
@@ -653,8 +663,8 @@ static void bfin_spi_pump_transfers(unsigned long data)
 		drv_data->len = transfer->len;
 	}
 	dev_dbg(&drv_data->pdev->dev,
-		"transfer: drv_data->write is %p, chip->write is %p\n",
-		drv_data->write, chip->write);
+		"transfer: drv_data->ops is %p, chip->ops is %p, u8_ops is %p\n",
+		drv_data->ops, chip->ops, &bfin_transfer_ops_u8);
 
 	message->state = RUNNING_STATE;
 	dma_config = 0;
@@ -819,7 +829,7 @@ static void bfin_spi_pump_transfers(unsigned long data)
 		dev_dbg(&drv_data->pdev->dev,
 			"IO duplex: cr is 0x%x\n", cr);
 
-		drv_data->duplex(drv_data);
+		drv_data->ops->duplex(drv_data);
 
 		if (drv_data->tx != drv_data->tx_end)
 			tranf_success = 0;
@@ -828,7 +838,7 @@ static void bfin_spi_pump_transfers(unsigned long data)
 		dev_dbg(&drv_data->pdev->dev,
 			"IO write: cr is 0x%x\n", cr);
 
-		drv_data->write(drv_data);
+		drv_data->ops->write(drv_data);
 
 		if (drv_data->tx != drv_data->tx_end)
 			tranf_success = 0;
@@ -837,7 +847,7 @@ static void bfin_spi_pump_transfers(unsigned long data)
 		dev_dbg(&drv_data->pdev->dev,
 			"IO read: cr is 0x%x\n", cr);
 
-		drv_data->read(drv_data);
+		drv_data->ops->read(drv_data);
 		if (drv_data->rx != drv_data->rx_end)
 			tranf_success = 0;
 	}
@@ -1032,17 +1042,13 @@ static int bfin_spi_setup(struct spi_device *spi)
 	case 8:
 		chip->n_bytes = 1;
 		chip->width = CFG_SPI_WORDSIZE8;
-		chip->read = bfin_spi_u8_reader;
-		chip->write = bfin_spi_u8_writer;
-		chip->duplex = bfin_spi_u8_duplex;
+		chip->ops = &bfin_transfer_ops_u8;
 		break;
 
 	case 16:
 		chip->n_bytes = 2;
 		chip->width = CFG_SPI_WORDSIZE16;
-		chip->read = bfin_spi_u16_reader;
-		chip->write = bfin_spi_u16_writer;
-		chip->duplex = bfin_spi_u16_duplex;
+		chip->ops = &bfin_transfer_ops_u16;
 		break;
 
 	default:
-- 
1.7.3.1


------------------------------------------------------------------------------
Download new Adobe(R) Flash(R) Builder(TM) 4
The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly 
Flex(R) Builder(TM)) enable the development of rich applications that run
across multiple browsers and platforms. Download your free trials today!
http://p.sf.net/sfu/adobe-dev2dev

[PATCH 11/28] Blackfin SPI: convert struct names to something more logical

[Mike Frysinger]

The current structure names are a bit confusing as to what they represent,
so use better names.

Reported-by: David Brownell <dbrownell-Rn4VEauK+AKRv+LV9MX5uipxlwaOVQ5f@public.gmane.org>
Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |  100 ++++++++++++++++++++++----------------------
 1 files changed, 50 insertions(+), 50 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index b0de61a..9a1801b 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -42,15 +42,15 @@ MODULE_LICENSE("GPL");
 #define DONE_STATE	((void *)2)
 #define ERROR_STATE	((void *)-1)
 
-struct driver_data;
+struct master_data;
 
 struct transfer_ops {
-	void (*write) (struct driver_data *);
-	void (*read) (struct driver_data *);
-	void (*duplex) (struct driver_data *);
+	void (*write) (struct master_data *);
+	void (*read) (struct master_data *);
+	void (*duplex) (struct master_data *);
 };
 
-struct driver_data {
+struct master_data {
 	/* Driver model hookup */
 	struct platform_device *pdev;
 
@@ -80,7 +80,7 @@ struct driver_data {
 	/* Current message transfer state info */
 	struct spi_message *cur_msg;
 	struct spi_transfer *cur_transfer;
-	struct chip_data *cur_chip;
+	struct slave_data *cur_chip;
 	size_t len_in_bytes;
 	size_t len;
 	void *tx;
@@ -105,7 +105,7 @@ struct driver_data {
 	const struct transfer_ops *ops;
 };
 
-struct chip_data {
+struct slave_data {
 	u16 ctl_reg;
 	u16 baud;
 	u16 flag;
@@ -123,9 +123,9 @@ struct chip_data {
 };
 
 #define DEFINE_SPI_REG(reg, off) \
-static inline u16 read_##reg(struct driver_data *drv_data) \
+static inline u16 read_##reg(struct master_data *drv_data) \
 	{ return bfin_read16(drv_data->regs_base + off); } \
-static inline void write_##reg(struct driver_data *drv_data, u16 v) \
+static inline void write_##reg(struct master_data *drv_data, u16 v) \
 	{ bfin_write16(drv_data->regs_base + off, v); }
 
 DEFINE_SPI_REG(CTRL, 0x00)
@@ -136,7 +136,7 @@ DEFINE_SPI_REG(RDBR, 0x10)
 DEFINE_SPI_REG(BAUD, 0x14)
 DEFINE_SPI_REG(SHAW, 0x18)
 
-static void bfin_spi_enable(struct driver_data *drv_data)
+static void bfin_spi_enable(struct master_data *drv_data)
 {
 	u16 cr;
 
@@ -144,7 +144,7 @@ static void bfin_spi_enable(struct driver_data *drv_data)
 	write_CTRL(drv_data, (cr | BIT_CTL_ENABLE));
 }
 
-static void bfin_spi_disable(struct driver_data *drv_data)
+static void bfin_spi_disable(struct master_data *drv_data)
 {
 	u16 cr;
 
@@ -167,7 +167,7 @@ static u16 hz_to_spi_baud(u32 speed_hz)
 	return spi_baud;
 }
 
-static int bfin_spi_flush(struct driver_data *drv_data)
+static int bfin_spi_flush(struct master_data *drv_data)
 {
 	unsigned long limit = loops_per_jiffy << 1;
 
@@ -181,7 +181,7 @@ static int bfin_spi_flush(struct driver_data *drv_data)
 }
 
 /* Chip select operation functions for cs_change flag */
-static void bfin_spi_cs_active(struct driver_data *drv_data, struct chip_data *chip)
+static void bfin_spi_cs_active(struct master_data *drv_data, struct slave_data *chip)
 {
 	if (likely(chip->chip_select_num)) {
 		u16 flag = read_FLAG(drv_data);
@@ -194,7 +194,7 @@ static void bfin_spi_cs_active(struct driver_data *drv_data, struct chip_data *c
 	}
 }
 
-static void bfin_spi_cs_deactive(struct driver_data *drv_data, struct chip_data *chip)
+static void bfin_spi_cs_deactive(struct master_data *drv_data, struct slave_data *chip)
 {
 	if (likely(chip->chip_select_num)) {
 		u16 flag = read_FLAG(drv_data);
@@ -212,7 +212,7 @@ static void bfin_spi_cs_deactive(struct driver_data *drv_data, struct chip_data
 }
 
 /* enable or disable the pin muxed by GPIO and SPI CS to work as SPI CS */
-static inline void bfin_spi_cs_enable(struct driver_data *drv_data, struct chip_data *chip)
+static inline void bfin_spi_cs_enable(struct master_data *drv_data, struct slave_data *chip)
 {
 	u16 flag = read_FLAG(drv_data);
 
@@ -221,7 +221,7 @@ static inline void bfin_spi_cs_enable(struct driver_data *drv_data, struct chip_
 	write_FLAG(drv_data, flag);
 }
 
-static inline void bfin_spi_cs_disable(struct driver_data *drv_data, struct chip_data *chip)
+static inline void bfin_spi_cs_disable(struct master_data *drv_data, struct slave_data *chip)
 {
 	u16 flag = read_FLAG(drv_data);
 
@@ -231,9 +231,9 @@ static inline void bfin_spi_cs_disable(struct driver_data *drv_data, struct chip
 }
 
 /* stop controller and re-config current chip*/
-static void bfin_spi_restore_state(struct driver_data *drv_data)
+static void bfin_spi_restore_state(struct master_data *drv_data)
 {
-	struct chip_data *chip = drv_data->cur_chip;
+	struct slave_data *chip = drv_data->cur_chip;
 
 	/* Clear status and disable clock */
 	write_STAT(drv_data, BIT_STAT_CLR);
@@ -249,12 +249,12 @@ static void bfin_spi_restore_state(struct driver_data *drv_data)
 }
 
 /* used to kick off transfer in rx mode and read unwanted RX data */
-static inline void bfin_spi_dummy_read(struct driver_data *drv_data)
+static inline void bfin_spi_dummy_read(struct master_data *drv_data)
 {
 	(void) read_RDBR(drv_data);
 }
 
-static void bfin_spi_u8_writer(struct driver_data *drv_data)
+static void bfin_spi_u8_writer(struct master_data *drv_data)
 {
 	/* clear RXS (we check for RXS inside the loop) */
 	bfin_spi_dummy_read(drv_data);
@@ -270,7 +270,7 @@ static void bfin_spi_u8_writer(struct driver_data *drv_data)
 	}
 }
 
-static void bfin_spi_u8_reader(struct driver_data *drv_data)
+static void bfin_spi_u8_reader(struct master_data *drv_data)
 {
 	u16 tx_val = drv_data->cur_chip->idle_tx_val;
 
@@ -285,7 +285,7 @@ static void bfin_spi_u8_reader(struct driver_data *drv_data)
 	}
 }
 
-static void bfin_spi_u8_duplex(struct driver_data *drv_data)
+static void bfin_spi_u8_duplex(struct master_data *drv_data)
 {
 	/* discard old RX data and clear RXS */
 	bfin_spi_dummy_read(drv_data);
@@ -304,7 +304,7 @@ static const struct transfer_ops bfin_transfer_ops_u8 = {
 	.duplex = bfin_spi_u8_duplex,
 };
 
-static void bfin_spi_u16_writer(struct driver_data *drv_data)
+static void bfin_spi_u16_writer(struct master_data *drv_data)
 {
 	/* clear RXS (we check for RXS inside the loop) */
 	bfin_spi_dummy_read(drv_data);
@@ -321,7 +321,7 @@ static void bfin_spi_u16_writer(struct driver_data *drv_data)
 	}
 }
 
-static void bfin_spi_u16_reader(struct driver_data *drv_data)
+static void bfin_spi_u16_reader(struct master_data *drv_data)
 {
 	u16 tx_val = drv_data->cur_chip->idle_tx_val;
 
@@ -337,7 +337,7 @@ static void bfin_spi_u16_reader(struct driver_data *drv_data)
 	}
 }
 
-static void bfin_spi_u16_duplex(struct driver_data *drv_data)
+static void bfin_spi_u16_duplex(struct master_data *drv_data)
 {
 	/* discard old RX data and clear RXS */
 	bfin_spi_dummy_read(drv_data);
@@ -359,7 +359,7 @@ static const struct transfer_ops bfin_transfer_ops_u16 = {
 };
 
 /* test if ther is more transfer to be done */
-static void *bfin_spi_next_transfer(struct driver_data *drv_data)
+static void *bfin_spi_next_transfer(struct master_data *drv_data)
 {
 	struct spi_message *msg = drv_data->cur_msg;
 	struct spi_transfer *trans = drv_data->cur_transfer;
@@ -378,9 +378,9 @@ static void *bfin_spi_next_transfer(struct driver_data *drv_data)
  * caller already set message->status;
  * dma and pio irqs are blocked give finished message back
  */
-static void bfin_spi_giveback(struct driver_data *drv_data)
+static void bfin_spi_giveback(struct master_data *drv_data)
 {
-	struct chip_data *chip = drv_data->cur_chip;
+	struct slave_data *chip = drv_data->cur_chip;
 	struct spi_transfer *last_transfer;
 	unsigned long flags;
 	struct spi_message *msg;
@@ -412,8 +412,8 @@ static void bfin_spi_giveback(struct driver_data *drv_data)
 /* spi data irq handler */
 static irqreturn_t bfin_spi_pio_irq_handler(int irq, void *dev_id)
 {
-	struct driver_data *drv_data = dev_id;
-	struct chip_data *chip = drv_data->cur_chip;
+	struct master_data *drv_data = dev_id;
+	struct slave_data *chip = drv_data->cur_chip;
 	struct spi_message *msg = drv_data->cur_msg;
 	int n_bytes = drv_data->n_bytes;
 
@@ -484,8 +484,8 @@ static irqreturn_t bfin_spi_pio_irq_handler(int irq, void *dev_id)
 
 static irqreturn_t bfin_spi_dma_irq_handler(int irq, void *dev_id)
 {
-	struct driver_data *drv_data = dev_id;
-	struct chip_data *chip = drv_data->cur_chip;
+	struct master_data *drv_data = dev_id;
+	struct slave_data *chip = drv_data->cur_chip;
 	struct spi_message *msg = drv_data->cur_msg;
 	unsigned long timeout;
 	unsigned short dmastat = get_dma_curr_irqstat(drv_data->dma_channel);
@@ -548,11 +548,11 @@ static irqreturn_t bfin_spi_dma_irq_handler(int irq, void *dev_id)
 
 static void bfin_spi_pump_transfers(unsigned long data)
 {
-	struct driver_data *drv_data = (struct driver_data *)data;
+	struct master_data *drv_data = (struct master_data *)data;
 	struct spi_message *message = NULL;
 	struct spi_transfer *transfer = NULL;
 	struct spi_transfer *previous = NULL;
-	struct chip_data *chip = NULL;
+	struct slave_data *chip = NULL;
 	u8 width;
 	u16 cr, dma_width, dma_config;
 	u32 tranf_success = 1;
@@ -872,10 +872,10 @@ static void bfin_spi_pump_transfers(unsigned long data)
 /* pop a msg from queue and kick off real transfer */
 static void bfin_spi_pump_messages(struct work_struct *work)
 {
-	struct driver_data *drv_data;
+	struct master_data *drv_data;
 	unsigned long flags;
 
-	drv_data = container_of(work, struct driver_data, pump_messages);
+	drv_data = container_of(work, struct master_data, pump_messages);
 
 	/* Lock queue and check for queue work */
 	spin_lock_irqsave(&drv_data->lock, flags);
@@ -929,7 +929,7 @@ static void bfin_spi_pump_messages(struct work_struct *work)
  */
 static int bfin_spi_transfer(struct spi_device *spi, struct spi_message *msg)
 {
-	struct driver_data *drv_data = spi_master_get_devdata(spi->master);
+	struct master_data *drv_data = spi_master_get_devdata(spi->master);
 	unsigned long flags;
 
 	spin_lock_irqsave(&drv_data->lock, flags);
@@ -974,8 +974,8 @@ static u16 ssel[][MAX_SPI_SSEL] = {
 static int bfin_spi_setup(struct spi_device *spi)
 {
 	struct bfin5xx_spi_chip *chip_info;
-	struct chip_data *chip = NULL;
-	struct driver_data *drv_data = spi_master_get_devdata(spi->master);
+	struct slave_data *chip = NULL;
+	struct master_data *drv_data = spi_master_get_devdata(spi->master);
 	int ret = -EINVAL;
 
 	if (spi->bits_per_word != 8 && spi->bits_per_word != 16)
@@ -1155,8 +1155,8 @@ static int bfin_spi_setup(struct spi_device *spi)
  */
 static void bfin_spi_cleanup(struct spi_device *spi)
 {
-	struct chip_data *chip = spi_get_ctldata(spi);
-	struct driver_data *drv_data = spi_master_get_devdata(spi->master);
+	struct slave_data *chip = spi_get_ctldata(spi);
+	struct master_data *drv_data = spi_master_get_devdata(spi->master);
 
 	if (!chip)
 		return;
@@ -1176,7 +1176,7 @@ static void bfin_spi_cleanup(struct spi_device *spi)
 	spi_set_ctldata(spi, NULL);
 }
 
-static inline int bfin_spi_init_queue(struct driver_data *drv_data)
+static inline int bfin_spi_init_queue(struct master_data *drv_data)
 {
 	INIT_LIST_HEAD(&drv_data->queue);
 	spin_lock_init(&drv_data->lock);
@@ -1198,7 +1198,7 @@ static inline int bfin_spi_init_queue(struct driver_data *drv_data)
 	return 0;
 }
 
-static inline int bfin_spi_start_queue(struct driver_data *drv_data)
+static inline int bfin_spi_start_queue(struct master_data *drv_data)
 {
 	unsigned long flags;
 
@@ -1220,7 +1220,7 @@ static inline int bfin_spi_start_queue(struct driver_data *drv_data)
 	return 0;
 }
 
-static inline int bfin_spi_stop_queue(struct driver_data *drv_data)
+static inline int bfin_spi_stop_queue(struct master_data *drv_data)
 {
 	unsigned long flags;
 	unsigned limit = 500;
@@ -1249,7 +1249,7 @@ static inline int bfin_spi_stop_queue(struct driver_data *drv_data)
 	return status;
 }
 
-static inline int bfin_spi_destroy_queue(struct driver_data *drv_data)
+static inline int bfin_spi_destroy_queue(struct master_data *drv_data)
 {
 	int status;
 
@@ -1267,14 +1267,14 @@ static int __init bfin_spi_probe(struct platform_device *pdev)
 	struct device *dev = &pdev->dev;
 	struct bfin5xx_spi_master *platform_info;
 	struct spi_master *master;
-	struct driver_data *drv_data = 0;
+	struct master_data *drv_data = 0;
 	struct resource *res;
 	int status = 0;
 
 	platform_info = dev->platform_data;
 
 	/* Allocate master with space for drv_data */
-	master = spi_alloc_master(dev, sizeof(struct driver_data) + 16);
+	master = spi_alloc_master(dev, sizeof(struct master_data) + 16);
 	if (!master) {
 		dev_err(&pdev->dev, "can not alloc spi_master\n");
 		return -ENOMEM;
@@ -1377,7 +1377,7 @@ out_error_get_res:
 /* stop hardware and remove the driver */
 static int __devexit bfin_spi_remove(struct platform_device *pdev)
 {
-	struct driver_data *drv_data = platform_get_drvdata(pdev);
+	struct master_data *drv_data = platform_get_drvdata(pdev);
 	int status = 0;
 
 	if (!drv_data)
@@ -1416,7 +1416,7 @@ static int __devexit bfin_spi_remove(struct platform_device *pdev)
 #ifdef CONFIG_PM
 static int bfin_spi_suspend(struct platform_device *pdev, pm_message_t state)
 {
-	struct driver_data *drv_data = platform_get_drvdata(pdev);
+	struct master_data *drv_data = platform_get_drvdata(pdev);
 	int status = 0;
 
 	status = bfin_spi_stop_queue(drv_data);
@@ -1431,7 +1431,7 @@ static int bfin_spi_suspend(struct platform_device *pdev, pm_message_t state)
 
 static int bfin_spi_resume(struct platform_device *pdev)
 {
-	struct driver_data *drv_data = platform_get_drvdata(pdev);
+	struct master_data *drv_data = platform_get_drvdata(pdev);
 	int status = 0;
 
 	/* Enable the SPI interface */
-- 
1.7.3.1

[PATCH 12/28] Blackfin SPI: drop extra memory we don't need

[Mike Frysinger]

The driver that we based ours on uses a little extra memory behind the
normal driver state, but we don't.  So drop this useless bit of memory.

Reported-by: David Brownell <dbrownell-Rn4VEauK+AKRv+LV9MX5uipxlwaOVQ5f@public.gmane.org>
Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |    4 ++--
 1 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index 9a1801b..ffff099 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -1267,14 +1267,14 @@ static int __init bfin_spi_probe(struct platform_device *pdev)
 	struct device *dev = &pdev->dev;
 	struct bfin5xx_spi_master *platform_info;
 	struct spi_master *master;
-	struct master_data *drv_data = 0;
+	struct master_data *drv_data;
 	struct resource *res;
 	int status = 0;
 
 	platform_info = dev->platform_data;
 
 	/* Allocate master with space for drv_data */
-	master = spi_alloc_master(dev, sizeof(struct master_data) + 16);
+	master = spi_alloc_master(dev, sizeof(*drv_data));
 	if (!master) {
 		dev_err(&pdev->dev, "can not alloc spi_master\n");
 		return -ENOMEM;
-- 
1.7.3.1

[PATCH 13/28] Blackfin SPI: use the SPI namespaced bit names

[Mike Frysinger]

This lets us push the short SPI MMR bit names out of the global namespace.

Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |   21 +++++++++++----------
 1 files changed, 11 insertions(+), 10 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index ffff099..07044d7 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -504,8 +504,8 @@ static irqreturn_t bfin_spi_dma_irq_handler(int irq, void *dev_id)
 	 * register until it goes low for 2 successive reads
 	 */
 	if (drv_data->tx != NULL) {
-		while ((read_STAT(drv_data) & TXS) ||
-		       (read_STAT(drv_data) & TXS))
+		while ((read_STAT(drv_data) & BIT_STAT_TXS) ||
+		       (read_STAT(drv_data) & BIT_STAT_TXS))
 			cpu_relax();
 	}
 
@@ -514,14 +514,14 @@ static irqreturn_t bfin_spi_dma_irq_handler(int irq, void *dev_id)
 		dmastat, read_STAT(drv_data));
 
 	timeout = jiffies + HZ;
-	while (!(read_STAT(drv_data) & SPIF))
+	while (!(read_STAT(drv_data) & BIT_STAT_SPIF))
 		if (!time_before(jiffies, timeout)) {
 			dev_warn(&drv_data->pdev->dev, "timeout waiting for SPIF");
 			break;
 		} else
 			cpu_relax();
 
-	if ((dmastat & DMA_ERR) && (spistat & RBSY)) {
+	if ((dmastat & DMA_ERR) && (spistat & BIT_STAT_RBSY)) {
 		msg->state = ERROR_STATE;
 		dev_err(&drv_data->pdev->dev, "dma receive: fifo/buffer overflow\n");
 	} else {
@@ -1000,11 +1000,12 @@ static int bfin_spi_setup(struct spi_device *spi)
 	if (chip_info) {
 		/* Make sure people stop trying to set fields via ctl_reg
 		 * when they should actually be using common SPI framework.
-		 * Currently we let through: WOM EMISO PSSE GM SZ TIMOD.
+		 * Currently we let through: WOM EMISO PSSE GM SZ.
 		 * Not sure if a user actually needs/uses any of these,
 		 * but let's assume (for now) they do.
 		 */
-		if (chip_info->ctl_reg & (SPE|MSTR|CPOL|CPHA|LSBF|SIZE)) {
+		if (chip_info->ctl_reg & ~(BIT_CTL_OPENDRAIN | BIT_CTL_EMISO | \
+		                           BIT_CTL_PSSE | BIT_CTL_GM | BIT_CTL_SZ)) {
 			dev_err(&spi->dev, "do not set bits in ctl_reg "
 				"that the SPI framework manages\n");
 			goto error;
@@ -1022,13 +1023,13 @@ static int bfin_spi_setup(struct spi_device *spi)
 
 	/* translate common spi framework into our register */
 	if (spi->mode & SPI_CPOL)
-		chip->ctl_reg |= CPOL;
+		chip->ctl_reg |= BIT_CTL_CPOL;
 	if (spi->mode & SPI_CPHA)
-		chip->ctl_reg |= CPHA;
+		chip->ctl_reg |= BIT_CTL_CPHA;
 	if (spi->mode & SPI_LSB_FIRST)
-		chip->ctl_reg |= LSBF;
+		chip->ctl_reg |= BIT_CTL_LSBF;
 	/* we dont support running in slave mode (yet?) */
-	chip->ctl_reg |= MSTR;
+	chip->ctl_reg |= BIT_CTL_MASTER;
 
 	/*
 	 * Notice: for blackfin, the speed_hz is the value of register
-- 
1.7.3.1

[PATCH 14/28] Blackfin: SPI: expand SPI bitmasks

[Mike Frysinger]

Expand the BIT_CTL defines to use the naming convention of the hardware,
and expand the masks to cover all documented bits.

Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 arch/blackfin/include/asm/bfin5xx_spi.h |   11 +++++++----
 1 files changed, 7 insertions(+), 4 deletions(-)

diff --git a/arch/blackfin/include/asm/bfin5xx_spi.h b/arch/blackfin/include/asm/bfin5xx_spi.h
index ee3ecb9..126d25e 100644
--- a/arch/blackfin/include/asm/bfin5xx_spi.h
+++ b/arch/blackfin/include/asm/bfin5xx_spi.h
@@ -26,11 +26,14 @@
 #define BIT_CTL_ENABLE      0x4000
 #define BIT_CTL_OPENDRAIN   0x2000
 #define BIT_CTL_MASTER      0x1000
-#define BIT_CTL_POLAR       0x0800
-#define BIT_CTL_PHASE       0x0400
-#define BIT_CTL_BITORDER    0x0200
+#define BIT_CTL_CPOL        0x0800
+#define BIT_CTL_CPHA        0x0400
+#define BIT_CTL_LSBF        0x0200
 #define BIT_CTL_WORDSIZE    0x0100
-#define BIT_CTL_MISOENABLE  0x0020
+#define BIT_CTL_EMISO       0x0020
+#define BIT_CTL_PSSE        0x0010
+#define BIT_CTL_GM          0x0008
+#define BIT_CTL_SZ          0x0004
 #define BIT_CTL_RXMOD       0x0000
 #define BIT_CTL_TXMOD       0x0001
 #define BIT_CTL_TIMOD_DMA_TX 0x0003
-- 
1.7.3.1

[PATCH 15/28] Blackfin SPI: redo GPIO CS handling

[Mike Frysinger]

From: Barry Song <barry.song-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>

The common SPI layers take care of detecting CS conflicts and preventing
two devices from claiming the same CS.  This causes problems for the GPIO
CS support we currently have as we are using CS0 to mean "GPIO CS".  But
if we have multiple devices using a GPIO CS, the common SPI layers see
multiple devices using the virtual "CS0" and reject any such attempts.

To make both work, we introduce an offset define.  This represents the
max number of hardware CS values that the SPI peripheral supports.  If
the CS is below this limit, we know we can use the hardware CS.  If it's
above, we treat it as a GPIO CS.  This keeps the CS unique as seen by
the common code and prevents conflicts.

Signed-off-by: Barry Song <barry.song-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 arch/blackfin/include/asm/bfin5xx_spi.h |    3 +-
 drivers/spi/spi_bfin5xx.c               |   40 ++++++++++++++++--------------
 2 files changed, 23 insertions(+), 20 deletions(-)

diff --git a/arch/blackfin/include/asm/bfin5xx_spi.h b/arch/blackfin/include/asm/bfin5xx_spi.h
index 126d25e..6f011da 100644
--- a/arch/blackfin/include/asm/bfin5xx_spi.h
+++ b/arch/blackfin/include/asm/bfin5xx_spi.h
@@ -109,6 +109,8 @@
 #define CMD_SPI_GET_SYSTEMCLOCK   25
 #define CMD_SPI_SET_WRITECONTINUOUS     26
 
+#define MAX_CTRL_CS          8  /* cs in spi controller */
+
 /* device.platform_data for SSP controller devices */
 struct bfin5xx_spi_master {
 	u16 num_chipselect;
@@ -124,7 +126,6 @@ struct bfin5xx_spi_chip {
 	u8 enable_dma;
 	u8 bits_per_word;
 	u16 cs_chg_udelay; /* Some devices require 16-bit delays */
-	u32 cs_gpio;
 	/* Value to send if no TX value is supplied, usually 0x0 or 0xFFFF */
 	u16 idle_tx_val;
 	u8 pio_interrupt; /* Enable spi data irq */
diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index 07044d7..278fe0a 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -183,7 +183,7 @@ static int bfin_spi_flush(struct master_data *drv_data)
 /* Chip select operation functions for cs_change flag */
 static void bfin_spi_cs_active(struct master_data *drv_data, struct slave_data *chip)
 {
-	if (likely(chip->chip_select_num)) {
+	if (likely(chip->chip_select_num < MAX_CTRL_CS)) {
 		u16 flag = read_FLAG(drv_data);
 
 		flag &= ~chip->flag;
@@ -196,7 +196,7 @@ static void bfin_spi_cs_active(struct master_data *drv_data, struct slave_data *
 
 static void bfin_spi_cs_deactive(struct master_data *drv_data, struct slave_data *chip)
 {
-	if (likely(chip->chip_select_num)) {
+	if (likely(chip->chip_select_num < MAX_CTRL_CS)) {
 		u16 flag = read_FLAG(drv_data);
 
 		flag |= chip->flag;
@@ -214,20 +214,24 @@ static void bfin_spi_cs_deactive(struct master_data *drv_data, struct slave_data
 /* enable or disable the pin muxed by GPIO and SPI CS to work as SPI CS */
 static inline void bfin_spi_cs_enable(struct master_data *drv_data, struct slave_data *chip)
 {
-	u16 flag = read_FLAG(drv_data);
+	if (chip->chip_select_num < MAX_CTRL_CS) {
+		u16 flag = read_FLAG(drv_data);
 
-	flag |= (chip->flag >> 8);
+		flag |= (chip->flag >> 8);
 
-	write_FLAG(drv_data, flag);
+		write_FLAG(drv_data, flag);
+	}
 }
 
 static inline void bfin_spi_cs_disable(struct master_data *drv_data, struct slave_data *chip)
 {
-	u16 flag = read_FLAG(drv_data);
+	if (chip->chip_select_num < MAX_CTRL_CS) {
+		u16 flag = read_FLAG(drv_data);
 
-	flag &= ~(chip->flag >> 8);
+		flag &= ~(chip->flag >> 8);
 
-	write_FLAG(drv_data, flag);
+		write_FLAG(drv_data, flag);
+	}
 }
 
 /* stop controller and re-config current chip*/
@@ -1016,7 +1020,6 @@ static int bfin_spi_setup(struct spi_device *spi)
 		chip->ctl_reg = chip_info->ctl_reg;
 		chip->bits_per_word = chip_info->bits_per_word;
 		chip->cs_chg_udelay = chip_info->cs_chg_udelay;
-		chip->cs_gpio = chip_info->cs_gpio;
 		chip->idle_tx_val = chip_info->idle_tx_val;
 		chip->pio_interrupt = chip_info->pio_interrupt;
 	}
@@ -1036,8 +1039,11 @@ static int bfin_spi_setup(struct spi_device *spi)
 	 * SPI_BAUD, not the real baudrate
 	 */
 	chip->baud = hz_to_spi_baud(spi->max_speed_hz);
-	chip->flag = (1 << (spi->chip_select)) << 8;
 	chip->chip_select_num = spi->chip_select;
+	if (chip->chip_select_num < MAX_CTRL_CS)
+		chip->flag = (1 << spi->chip_select) << 8;
+	else
+		chip->cs_gpio = chip->chip_select_num - MAX_CTRL_CS;
 
 	switch (chip->bits_per_word) {
 	case 8:
@@ -1098,7 +1104,7 @@ static int bfin_spi_setup(struct spi_device *spi)
 		disable_irq(drv_data->spi_irq);
 	}
 
-	if (chip->chip_select_num == 0) {
+	if (chip->chip_select_num >= MAX_CTRL_CS) {
 		ret = gpio_request(chip->cs_gpio, spi->modalias);
 		if (ret) {
 			dev_err(&spi->dev, "gpio_request() error\n");
@@ -1115,8 +1121,7 @@ static int bfin_spi_setup(struct spi_device *spi)
 	spi_set_ctldata(spi, chip);
 
 	dev_dbg(&spi->dev, "chip select number is %d\n", chip->chip_select_num);
-	if (chip->chip_select_num > 0 &&
-	    chip->chip_select_num <= spi->master->num_chipselect) {
+	if (chip->chip_select_num < MAX_CTRL_CS) {
 		ret = peripheral_request(ssel[spi->master->bus_num]
 		                         [chip->chip_select_num-1], spi->modalias);
 		if (ret) {
@@ -1131,7 +1136,7 @@ static int bfin_spi_setup(struct spi_device *spi)
 	return 0;
 
  pin_error:
-	if (chip->chip_select_num == 0)
+	if (chip->chip_select_num >= MAX_CTRL_CS)
 		gpio_free(chip->cs_gpio);
 	else
 		peripheral_free(ssel[spi->master->bus_num]
@@ -1162,14 +1167,11 @@ static void bfin_spi_cleanup(struct spi_device *spi)
 	if (!chip)
 		return;
 
-	if ((chip->chip_select_num > 0)
-		&& (chip->chip_select_num <= spi->master->num_chipselect)) {
+	if (chip->chip_select_num < MAX_CTRL_CS) {
 		peripheral_free(ssel[spi->master->bus_num]
 					[chip->chip_select_num-1]);
 		bfin_spi_cs_disable(drv_data, chip);
-	}
-
-	if (chip->chip_select_num == 0)
+	} else
 		gpio_free(chip->cs_gpio);
 
 	kfree(chip);
-- 
1.7.3.1


------------------------------------------------------------------------------
Download new Adobe(R) Flash(R) Builder(TM) 4
The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly 
Flex(R) Builder(TM)) enable the development of rich applications that run
across multiple browsers and platforms. Download your free trials today!
http://p.sf.net/sfu/adobe-dev2dev

[PATCH 16/28] Blackfin SPI: save/restore state when suspending/resuming

[Mike Frysinger]

From: Barry Song <barry.song-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>

We can't rely on the SPI_CTL/SPI_FLG registers retaining their state when
suspending, so save/restore their entire values.

Signed-off-by: Barry Song <barry.song-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |   17 +++++++++++++----
 1 files changed, 13 insertions(+), 4 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index 278fe0a..c23ac3b 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -101,6 +101,9 @@ struct master_data {
 	size_t rx_map_len;
 	size_t tx_map_len;
 	u8 n_bytes;
+	u16 ctrl_reg;
+	u16 flag_reg;
+
 	int cs_change;
 	const struct transfer_ops *ops;
 };
@@ -1426,8 +1429,14 @@ static int bfin_spi_suspend(struct platform_device *pdev, pm_message_t state)
 	if (status != 0)
 		return status;
 
-	/* stop hardware */
-	bfin_spi_disable(drv_data);
+	drv_data->ctrl_reg = read_CTRL(drv_data);
+	drv_data->flag_reg = read_FLAG(drv_data);
+
+	/*
+	 * reset SPI_CTL and SPI_FLG registers
+	 */
+	write_CTRL(drv_data, BIT_CTL_CPHA | BIT_CTL_MASTER);
+	write_FLAG(drv_data, 0xFF00);
 
 	return 0;
 }
@@ -1437,8 +1446,8 @@ static int bfin_spi_resume(struct platform_device *pdev)
 	struct master_data *drv_data = platform_get_drvdata(pdev);
 	int status = 0;
 
-	/* Enable the SPI interface */
-	bfin_spi_enable(drv_data);
+	write_CTRL(drv_data, drv_data->ctrl_reg);
+	write_FLAG(drv_data, drv_data->flag_reg);
 
 	/* Start the queue running */
 	status = bfin_spi_start_queue(drv_data);
-- 
1.7.3.1


------------------------------------------------------------------------------
Download new Adobe(R) Flash(R) Builder(TM) 4
The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly 
Flex(R) Builder(TM)) enable the development of rich applications that run
across multiple browsers and platforms. Download your free trials today!
http://p.sf.net/sfu/adobe-dev2dev

[PATCH 17/28] Blackfin SPI: sync hardware state before reprogramming everything

[Mike Frysinger]

From: Barry Song <barry.song-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>

Sometimes under load, the Blackfin core is able to send SPI register
updates out before the controller is actually disabled.  So when we
go to reprogram the entire state (to switch to a different slave),
make sure we sync after disabling the controller.

Signed-off-by: Barry Song <barry.song-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |    2 ++
 1 files changed, 2 insertions(+), 0 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index c23ac3b..54f9dbb 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -247,6 +247,8 @@ static void bfin_spi_restore_state(struct master_data *drv_data)
 	bfin_spi_disable(drv_data);
 	dev_dbg(&drv_data->pdev->dev, "restoring spi ctl state\n");
 
+	SSYNC();
+
 	/* Load the registers */
 	write_CTRL(drv_data, chip->ctl_reg);
 	write_BAUD(drv_data, chip->baud);
-- 
1.7.3.1


------------------------------------------------------------------------------
Download new Adobe(R) Flash(R) Builder(TM) 4
The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly 
Flex(R) Builder(TM)) enable the development of rich applications that run
across multiple browsers and platforms. Download your free trials today!
http://p.sf.net/sfu/adobe-dev2dev

[PATCH 18/28] Blackfin SPI: use nosync when disabling the IRQ from the IRQ handler

[Mike Frysinger]

From: Yi Li <yi.li-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>

Using disable_irq() on the IRQ whose handler we are currently executing in
can easily lead to a hang.  So use the nosync variant here.

Signed-off-by: Yi Li <yi.li-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index 54f9dbb..d446524 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -448,7 +448,7 @@ static irqreturn_t bfin_spi_pio_irq_handler(int irq, void *dev_id)
 		/* Move to next transfer */
 		msg->state = bfin_spi_next_transfer(drv_data);
 
-		disable_irq(drv_data->spi_irq);
+		disable_irq_nosync(drv_data->spi_irq);
 
 		/* Schedule transfer tasklet */
 		tasklet_schedule(&drv_data->pump_transfers);
-- 
1.7.3.1


------------------------------------------------------------------------------
Download new Adobe(R) Flash(R) Builder(TM) 4
The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly 
Flex(R) Builder(TM)) enable the development of rich applications that run
across multiple browsers and platforms. Download your free trials today!
http://p.sf.net/sfu/adobe-dev2dev

[PATCH 19/28] Blackfin SPI: push all size checks into the transfer function

[Mike Frysinger]

This reduces duplication between the setup/transfer functions and keeps
values cached during setup from overriding values changed on a transfer
basis (like bits_per_word).

Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |   57 +++++++++++----------------------------------
 1 files changed, 14 insertions(+), 43 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index d446524..830c705 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -114,10 +114,7 @@ struct slave_data {
 	u16 flag;
 
 	u8 chip_select_num;
-	u8 n_bytes;
-	u8 width;		/* 0 or 1 */
 	u8 enable_dma;
-	u8 bits_per_word;	/* 8 or 16 */
 	u16 cs_chg_udelay;	/* Some devices require > 255usec delay */
 	u32 cs_gpio;
 	u16 idle_tx_val;
@@ -562,6 +559,7 @@ static void bfin_spi_pump_transfers(unsigned long data)
 	struct spi_transfer *transfer = NULL;
 	struct spi_transfer *previous = NULL;
 	struct slave_data *chip = NULL;
+	unsigned int bits_per_word;
 	u8 width;
 	u16 cr, dma_width, dma_config;
 	u32 tranf_success = 1;
@@ -641,26 +639,15 @@ static void bfin_spi_pump_transfers(unsigned long data)
 	drv_data->cs_change = transfer->cs_change;
 
 	/* Bits per word setup */
-	switch (transfer->bits_per_word) {
-	case 8:
+	bits_per_word = transfer->bits_per_word ? : message->spi->bits_per_word;
+	if (bits_per_word == 8) {
 		drv_data->n_bytes = 1;
 		width = CFG_SPI_WORDSIZE8;
 		drv_data->ops = &bfin_transfer_ops_u8;
-		break;
-
-	case 16:
+	} else {
 		drv_data->n_bytes = 2;
 		width = CFG_SPI_WORDSIZE16;
 		drv_data->ops = &bfin_transfer_ops_u16;
-		break;
-
-	default:
-		/* No change, the same as default setting */
-		transfer->bits_per_word = chip->bits_per_word;
-		drv_data->n_bytes = chip->n_bytes;
-		width = chip->width;
-		drv_data->ops = chip->ops;
-		break;
 	}
 	cr = (read_CTRL(drv_data) & (~BIT_CTL_TIMOD));
 	cr |= (width << 8);
@@ -811,9 +798,9 @@ static void bfin_spi_pump_transfers(unsigned long data)
 		if (drv_data->tx == NULL)
 			write_TDBR(drv_data, chip->idle_tx_val);
 		else {
-			if (transfer->bits_per_word == 8)
+			if (bits_per_word == 8)
 				write_TDBR(drv_data, (*(u8 *) (drv_data->tx)));
-			else if (transfer->bits_per_word == 16)
+			else
 				write_TDBR(drv_data, (*(u16 *) (drv_data->tx)));
 			drv_data->tx += drv_data->n_bytes;
 		}
@@ -987,9 +974,6 @@ static int bfin_spi_setup(struct spi_device *spi)
 	struct master_data *drv_data = spi_master_get_devdata(spi->master);
 	int ret = -EINVAL;
 
-	if (spi->bits_per_word != 8 && spi->bits_per_word != 16)
-		goto error;
-
 	/* Only alloc (or use chip_info) on first setup */
 	chip_info = NULL;
 	chip = spi_get_ctldata(spi);
@@ -1023,10 +1007,16 @@ static int bfin_spi_setup(struct spi_device *spi)
 		chip->enable_dma = chip_info->enable_dma != 0
 		    && drv_data->master_info->enable_dma;
 		chip->ctl_reg = chip_info->ctl_reg;
-		chip->bits_per_word = chip_info->bits_per_word;
 		chip->cs_chg_udelay = chip_info->cs_chg_udelay;
 		chip->idle_tx_val = chip_info->idle_tx_val;
 		chip->pio_interrupt = chip_info->pio_interrupt;
+		spi->bits_per_word = chip_info->bits_per_word;
+	}
+
+	if (spi->bits_per_word != 8 && spi->bits_per_word != 16) {
+		dev_err(&spi->dev, "%d bits_per_word is not supported\n",
+				spi->bits_per_word);
+		goto error;
 	}
 
 	/* translate common spi framework into our register */
@@ -1050,25 +1040,6 @@ static int bfin_spi_setup(struct spi_device *spi)
 	else
 		chip->cs_gpio = chip->chip_select_num - MAX_CTRL_CS;
 
-	switch (chip->bits_per_word) {
-	case 8:
-		chip->n_bytes = 1;
-		chip->width = CFG_SPI_WORDSIZE8;
-		chip->ops = &bfin_transfer_ops_u8;
-		break;
-
-	case 16:
-		chip->n_bytes = 2;
-		chip->width = CFG_SPI_WORDSIZE16;
-		chip->ops = &bfin_transfer_ops_u16;
-		break;
-
-	default:
-		dev_err(&spi->dev, "%d bits_per_word is not supported\n",
-				chip->bits_per_word);
-		goto error;
-	}
-
 	if (chip->enable_dma && chip->pio_interrupt) {
 		dev_err(&spi->dev, "enable_dma is set, "
 				"do not set pio_interrupt\n");
@@ -1119,7 +1090,7 @@ static int bfin_spi_setup(struct spi_device *spi)
 	}
 
 	dev_dbg(&spi->dev, "setup spi chip %s, width is %d, dma is %d\n",
-			spi->modalias, chip->width, chip->enable_dma);
+			spi->modalias, spi->bits_per_word, chip->enable_dma);
 	dev_dbg(&spi->dev, "ctl_reg is 0x%x, flag_reg is 0x%x\n",
 			chip->ctl_reg, chip->flag);
 
-- 
1.7.3.1


------------------------------------------------------------------------------
Download new Adobe(R) Flash(R) Builder(TM) 4
The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly 
Flex(R) Builder(TM)) enable the development of rich applications that run
across multiple browsers and platforms. Download your free trials today!
http://p.sf.net/sfu/adobe-dev2dev

[PATCH 20/28] Blackfin SPI: reset ctl_reg bits when setup is run again on a device

[Mike Frysinger]

During runtime, the spi setup function may be called multiple times on the
same device in order to reconfigure some settings on the fly.  When this
happens, we need to reset the ctl_reg bits so that changing the mode works
as expected.

Reported-by: Andy Getzendanner <james.getzendanner-9geRo0GdX4k6efY3Smnssodd74u8MsAO@public.gmane.org>
Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |   12 +++++++++---
 1 files changed, 9 insertions(+), 3 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index 830c705..376f2f0 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -972,6 +972,7 @@ static int bfin_spi_setup(struct spi_device *spi)
 	struct bfin5xx_spi_chip *chip_info;
 	struct slave_data *chip = NULL;
 	struct master_data *drv_data = spi_master_get_devdata(spi->master);
+	u16 bfin_ctl_reg;
 	int ret = -EINVAL;
 
 	/* Only alloc (or use chip_info) on first setup */
@@ -989,6 +990,10 @@ static int bfin_spi_setup(struct spi_device *spi)
 		chip_info = spi->controller_data;
 	}
 
+	/* Let people set non-standard bits directly */
+	bfin_ctl_reg = BIT_CTL_OPENDRAIN | BIT_CTL_EMISO |
+		BIT_CTL_PSSE | BIT_CTL_GM | BIT_CTL_SZ;
+
 	/* chip_info isn't always needed */
 	if (chip_info) {
 		/* Make sure people stop trying to set fields via ctl_reg
@@ -997,13 +1002,11 @@ static int bfin_spi_setup(struct spi_device *spi)
 		 * Not sure if a user actually needs/uses any of these,
 		 * but let's assume (for now) they do.
 		 */
-		if (chip_info->ctl_reg & ~(BIT_CTL_OPENDRAIN | BIT_CTL_EMISO | \
-		                           BIT_CTL_PSSE | BIT_CTL_GM | BIT_CTL_SZ)) {
+		if (chip_info->ctl_reg & ~bfin_ctl_reg) {
 			dev_err(&spi->dev, "do not set bits in ctl_reg "
 				"that the SPI framework manages\n");
 			goto error;
 		}
-
 		chip->enable_dma = chip_info->enable_dma != 0
 		    && drv_data->master_info->enable_dma;
 		chip->ctl_reg = chip_info->ctl_reg;
@@ -1011,6 +1014,9 @@ static int bfin_spi_setup(struct spi_device *spi)
 		chip->idle_tx_val = chip_info->idle_tx_val;
 		chip->pio_interrupt = chip_info->pio_interrupt;
 		spi->bits_per_word = chip_info->bits_per_word;
+	} else {
+		/* force a default base state */
+		chip->ctl_reg &= bfin_ctl_reg;
 	}
 
 	if (spi->bits_per_word != 8 && spi->bits_per_word != 16) {
-- 
1.7.3.1


------------------------------------------------------------------------------
Download new Adobe(R) Flash(R) Builder(TM) 4
The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly 
Flex(R) Builder(TM)) enable the development of rich applications that run
across multiple browsers and platforms. Download your free trials today!
http://p.sf.net/sfu/adobe-dev2dev

[PATCH 21/28] Blackfin SPI: combine duplicate SPI_CTL read/write logic

[Mike Frysinger]

While combining things, also switch to the proper SPI bit define names.
This lets us punt the rarely used SPI defines.

Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 arch/blackfin/include/asm/bfin5xx_spi.h |   68 -------------------------------
 drivers/spi/spi_bfin5xx.c               |   40 ++++++++----------
 2 files changed, 18 insertions(+), 90 deletions(-)

diff --git a/arch/blackfin/include/asm/bfin5xx_spi.h b/arch/blackfin/include/asm/bfin5xx_spi.h
index 6f011da..4223cf0 100644
--- a/arch/blackfin/include/asm/bfin5xx_spi.h
+++ b/arch/blackfin/include/asm/bfin5xx_spi.h
@@ -11,18 +11,6 @@
 
 #define MIN_SPI_BAUD_VAL	2
 
-#define SPI_READ              0
-#define SPI_WRITE             1
-
-#define SPI_CTRL_OFF            0x0
-#define SPI_FLAG_OFF            0x4
-#define SPI_STAT_OFF            0x8
-#define SPI_TXBUFF_OFF          0xc
-#define SPI_RXBUFF_OFF          0x10
-#define SPI_BAUD_OFF            0x14
-#define SPI_SHAW_OFF            0x18
-
-
 #define BIT_CTL_ENABLE      0x4000
 #define BIT_CTL_OPENDRAIN   0x2000
 #define BIT_CTL_MASTER      0x1000
@@ -53,62 +41,6 @@
 #define BIT_STU_SENDOVER    0x0001
 #define BIT_STU_RECVFULL    0x0020
 
-#define CFG_SPI_ENABLE      1
-#define CFG_SPI_DISABLE     0
-
-#define CFG_SPI_OUTENABLE   1
-#define CFG_SPI_OUTDISABLE  0
-
-#define CFG_SPI_ACTLOW      1
-#define CFG_SPI_ACTHIGH     0
-
-#define CFG_SPI_PHASESTART  1
-#define CFG_SPI_PHASEMID    0
-
-#define CFG_SPI_MASTER      1
-#define CFG_SPI_SLAVE       0
-
-#define CFG_SPI_SENELAST    0
-#define CFG_SPI_SENDZERO    1
-
-#define CFG_SPI_RCVFLUSH    1
-#define CFG_SPI_RCVDISCARD  0
-
-#define CFG_SPI_LSBFIRST    1
-#define CFG_SPI_MSBFIRST    0
-
-#define CFG_SPI_WORDSIZE16  1
-#define CFG_SPI_WORDSIZE8   0
-
-#define CFG_SPI_MISOENABLE   1
-#define CFG_SPI_MISODISABLE  0
-
-#define CFG_SPI_READ      0x00
-#define CFG_SPI_WRITE     0x01
-#define CFG_SPI_DMAREAD   0x02
-#define CFG_SPI_DMAWRITE  0x03
-
-#define CFG_SPI_CSCLEARALL  0
-#define CFG_SPI_CHIPSEL1    1
-#define CFG_SPI_CHIPSEL2    2
-#define CFG_SPI_CHIPSEL3    3
-#define CFG_SPI_CHIPSEL4    4
-#define CFG_SPI_CHIPSEL5    5
-#define CFG_SPI_CHIPSEL6    6
-#define CFG_SPI_CHIPSEL7    7
-
-#define CFG_SPI_CS1VALUE    1
-#define CFG_SPI_CS2VALUE    2
-#define CFG_SPI_CS3VALUE    3
-#define CFG_SPI_CS4VALUE    4
-#define CFG_SPI_CS5VALUE    5
-#define CFG_SPI_CS6VALUE    6
-#define CFG_SPI_CS7VALUE    7
-
-#define CMD_SPI_SET_BAUDRATE  2
-#define CMD_SPI_GET_SYSTEMCLOCK   25
-#define CMD_SPI_SET_WRITECONTINUOUS     26
-
 #define MAX_CTRL_CS          8  /* cs in spi controller */
 
 /* device.platform_data for SSP controller devices */
diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index 376f2f0..b3450b7 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -560,8 +560,7 @@ static void bfin_spi_pump_transfers(unsigned long data)
 	struct spi_transfer *previous = NULL;
 	struct slave_data *chip = NULL;
 	unsigned int bits_per_word;
-	u8 width;
-	u16 cr, dma_width, dma_config;
+	u16 cr, cr_width, dma_width, dma_config;
 	u32 tranf_success = 1;
 	u8 full_duplex = 0;
 
@@ -642,22 +641,19 @@ static void bfin_spi_pump_transfers(unsigned long data)
 	bits_per_word = transfer->bits_per_word ? : message->spi->bits_per_word;
 	if (bits_per_word == 8) {
 		drv_data->n_bytes = 1;
-		width = CFG_SPI_WORDSIZE8;
+		drv_data->len = transfer->len;
+		cr_width = 0;
 		drv_data->ops = &bfin_transfer_ops_u8;
 	} else {
 		drv_data->n_bytes = 2;
-		width = CFG_SPI_WORDSIZE16;
+		drv_data->len = (transfer->len) >> 1;
+		cr_width = BIT_CTL_WORDSIZE;
 		drv_data->ops = &bfin_transfer_ops_u16;
 	}
-	cr = (read_CTRL(drv_data) & (~BIT_CTL_TIMOD));
-	cr |= (width << 8);
+	cr = read_CTRL(drv_data) & ~(BIT_CTL_TIMOD | BIT_CTL_WORDSIZE);
+	cr |= cr_width;
 	write_CTRL(drv_data, cr);
 
-	if (width == CFG_SPI_WORDSIZE16) {
-		drv_data->len = (transfer->len) >> 1;
-	} else {
-		drv_data->len = transfer->len;
-	}
 	dev_dbg(&drv_data->pdev->dev,
 		"transfer: drv_data->ops is %p, chip->ops is %p, u8_ops is %p\n",
 		drv_data->ops, chip->ops, &bfin_transfer_ops_u8);
@@ -672,13 +668,12 @@ static void bfin_spi_pump_transfers(unsigned long data)
 		write_BAUD(drv_data, chip->baud);
 
 	write_STAT(drv_data, BIT_STAT_CLR);
-	cr = (read_CTRL(drv_data) & (~BIT_CTL_TIMOD));
 	if (drv_data->cs_change)
 		bfin_spi_cs_active(drv_data, chip);
 
 	dev_dbg(&drv_data->pdev->dev,
 		"now pumping a transfer: width is %d, len is %d\n",
-		width, transfer->len);
+		cr_width, transfer->len);
 
 	/*
 	 * Try to map dma buffer and do a dma transfer.  If successful use,
@@ -697,7 +692,7 @@ static void bfin_spi_pump_transfers(unsigned long data)
 		/* config dma channel */
 		dev_dbg(&drv_data->pdev->dev, "doing dma transfer\n");
 		set_dma_x_count(drv_data->dma_channel, drv_data->len);
-		if (width == CFG_SPI_WORDSIZE16) {
+		if (cr_width == BIT_CTL_WORDSIZE) {
 			set_dma_x_modify(drv_data->dma_channel, 2);
 			dma_width = WDSIZE_16;
 		} else {
@@ -786,10 +781,16 @@ static void bfin_spi_pump_transfers(unsigned long data)
 		return;
 	}
 
+	/*
+	 * We always use SPI_WRITE mode (transfer starts with TDBR write).
+	 * SPI_READ mode (transfer starts with RDBR read) seems to have
+	 * problems with setting up the output value in TDBR prior to the
+	 * start of the transfer.
+	 */
+	write_CTRL(drv_data, cr | BIT_CTL_TXMOD);
+
 	if (chip->pio_interrupt) {
-		/* use write mode. spi irq should have been disabled */
-		cr = (read_CTRL(drv_data) & (~BIT_CTL_TIMOD));
-		write_CTRL(drv_data, (cr | CFG_SPI_WRITE));
+		/* SPI irq should have been disabled by now */
 
 		/* discard old RX data and clear RXS */
 		bfin_spi_dummy_read(drv_data);
@@ -813,11 +814,6 @@ static void bfin_spi_pump_transfers(unsigned long data)
 	/* IO mode */
 	dev_dbg(&drv_data->pdev->dev, "doing IO transfer\n");
 
-	/* we always use SPI_WRITE mode. SPI_READ mode
-	   seems to have problems with setting up the
-	   output value in TDBR prior to the transfer. */
-	write_CTRL(drv_data, (cr | CFG_SPI_WRITE));
-
 	if (full_duplex) {
 		/* full duplex mode */
 		BUG_ON((drv_data->tx_end - drv_data->tx) !=
-- 
1.7.3.1


------------------------------------------------------------------------------
Download new Adobe(R) Flash(R) Builder(TM) 4
The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly 
Flex(R) Builder(TM)) enable the development of rich applications that run
across multiple browsers and platforms. Download your free trials today!
http://p.sf.net/sfu/adobe-dev2dev

[PATCH 22/28] Blackfin SPI: use dma_disable_irq_nosync() in irq handler

[Mike Frysinger]

From: Barry Song <barry.song-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>

Using disable_irq() on the IRQ whose handler we are currently executing in
can easily lead to a hang.  So use the nosync variant here.

Signed-off-by: Barry Song <barry.song-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index b3450b7..18b313a 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -547,7 +547,7 @@ static irqreturn_t bfin_spi_dma_irq_handler(int irq, void *dev_id)
 	dev_dbg(&drv_data->pdev->dev,
 		"disable dma channel irq%d\n",
 		drv_data->dma_channel);
-	dma_disable_irq(drv_data->dma_channel);
+	dma_disable_irq_nosync(drv_data->dma_channel);
 
 	return IRQ_HANDLED;
 }
-- 
1.7.3.1


------------------------------------------------------------------------------
Download new Adobe(R) Flash(R) Builder(TM) 4
The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly 
Flex(R) Builder(TM)) enable the development of rich applications that run
across multiple browsers and platforms. Download your free trials today!
http://p.sf.net/sfu/adobe-dev2dev

[PATCH 23/28] Blackfin SPI: reject unsupported SPI modes

[Mike Frysinger]

Who knows what people will try!

Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |    4 ++++
 1 files changed, 4 insertions(+), 0 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index 18b313a..a91e556 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -1022,6 +1022,10 @@ static int bfin_spi_setup(struct spi_device *spi)
 	}
 
 	/* translate common spi framework into our register */
+	if (spi->mode & ~(SPI_CPOL | SPI_CPHA | SPI_LSB_FIRST)) {
+		dev_err(&spi->dev, "unsupported spi modes detected\n");
+		goto error;
+	}
 	if (spi->mode & SPI_CPOL)
 		chip->ctl_reg |= BIT_CTL_CPOL;
 	if (spi->mode & SPI_CPHA)
-- 
1.7.3.1


------------------------------------------------------------------------------
Download new Adobe(R) Flash(R) Builder(TM) 4
The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly 
Flex(R) Builder(TM)) enable the development of rich applications that run
across multiple browsers and platforms. Download your free trials today!
http://p.sf.net/sfu/adobe-dev2dev

[PATCH 24/28] Blackfin SPI: fix typo in comment

[Mike Frysinger]

From: Rob Maris <maris.rob-rHNaxI9ti4Y@public.gmane.org>

Signed-off-by: Rob Maris <maris.rob-rHNaxI9ti4Y@public.gmane.org>
Signed-off-by: Barry Song <barry.song-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index a91e556..550aaf7 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -364,7 +364,7 @@ static const struct transfer_ops bfin_transfer_ops_u16 = {
 	.duplex = bfin_spi_u16_duplex,
 };
 
-/* test if ther is more transfer to be done */
+/* test if there is more transfer to be done */
 static void *bfin_spi_next_transfer(struct master_data *drv_data)
 {
 	struct spi_message *msg = drv_data->cur_msg;
-- 
1.7.3.1


------------------------------------------------------------------------------
Download new Adobe(R) Flash(R) Builder(TM) 4
The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly 
Flex(R) Builder(TM)) enable the development of rich applications that run
across multiple browsers and platforms. Download your free trials today!
http://p.sf.net/sfu/adobe-dev2dev

[PATCH 25/28] Blackfin SPI: cs should be always low when a new transfer begins

[Mike Frysinger]

From: Rob Maris <maris.rob-rHNaxI9ti4Y@public.gmane.org>

Signed-off-by: Rob Maris <maris.rob-rHNaxI9ti4Y@public.gmane.org>
Signed-off-by: Barry Song <barry.song-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |    3 +--
 1 files changed, 1 insertions(+), 2 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index 550aaf7..7882afc 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -668,8 +668,7 @@ static void bfin_spi_pump_transfers(unsigned long data)
 		write_BAUD(drv_data, chip->baud);
 
 	write_STAT(drv_data, BIT_STAT_CLR);
-	if (drv_data->cs_change)
-		bfin_spi_cs_active(drv_data, chip);
+	bfin_spi_cs_active(drv_data, chip);
 
 	dev_dbg(&drv_data->pdev->dev,
 		"now pumping a transfer: width is %d, len is %d\n",
-- 
1.7.3.1


------------------------------------------------------------------------------
Download new Adobe(R) Flash(R) Builder(TM) 4
The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly 
Flex(R) Builder(TM)) enable the development of rich applications that run
across multiple browsers and platforms. Download your free trials today!
http://p.sf.net/sfu/adobe-dev2dev

[PATCH 26/28] Blackfin SPI: warn when CS is driven by hardware (CPHA=0)

[Mike Frysinger]

From: Barry Song <barry.song-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>

When the hardware is controlling the CS, there are some SPI options
we are unable to support.  So issue a warning in the hopes that the
user will change to a SPI mode where we can support things sanely.

Signed-off-by: Barry Song <barry.song-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |    9 +++++++--
 1 files changed, 7 insertions(+), 2 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index 7882afc..21de860 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -1040,9 +1040,14 @@ static int bfin_spi_setup(struct spi_device *spi)
 	 */
 	chip->baud = hz_to_spi_baud(spi->max_speed_hz);
 	chip->chip_select_num = spi->chip_select;
-	if (chip->chip_select_num < MAX_CTRL_CS)
+	if (chip->chip_select_num < MAX_CTRL_CS) {
+		if (!(spi->mode & SPI_CPHA))
+			dev_warn(&spi->dev, "Warning: SPI CPHA not set:"
+				" Slave Select not under software control!\n"
+				" See Documentation/blackfin/bfin-spi-notes.txt");
+
 		chip->flag = (1 << spi->chip_select) << 8;
-	else
+	} else
 		chip->cs_gpio = chip->chip_select_num - MAX_CTRL_CS;
 
 	if (chip->enable_dma && chip->pio_interrupt) {
-- 
1.7.3.1


------------------------------------------------------------------------------
Download new Adobe(R) Flash(R) Builder(TM) 4
The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly 
Flex(R) Builder(TM)) enable the development of rich applications that run
across multiple browsers and platforms. Download your free trials today!
http://p.sf.net/sfu/adobe-dev2dev

[PATCH 27/28] Blackfin SPI: check per-transfer bits_per_word

[Mike Frysinger]

From: Bob Liu <lliubbo-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>

Currently, if the bits_per_word when doing a transfer is not 8bits, we
always treat it as 16bits when we should actually be returning an error.

Signed-off-by: Bob Liu <lliubbo-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |    7 ++++++-
 1 files changed, 6 insertions(+), 1 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index 21de860..bd18214 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -644,11 +644,16 @@ static void bfin_spi_pump_transfers(unsigned long data)
 		drv_data->len = transfer->len;
 		cr_width = 0;
 		drv_data->ops = &bfin_transfer_ops_u8;
-	} else {
+	} else if (bits_per_word == 16) {
 		drv_data->n_bytes = 2;
 		drv_data->len = (transfer->len) >> 1;
 		cr_width = BIT_CTL_WORDSIZE;
 		drv_data->ops = &bfin_transfer_ops_u16;
+	} else {
+		dev_err(&drv_data->pdev->dev, "transfer: unsupported bits_per_word\n");
+		message->status = -EINVAL;
+		bfin_spi_giveback(drv_data);
+		return;
 	}
 	cr = read_CTRL(drv_data) & ~(BIT_CTL_TIMOD | BIT_CTL_WORDSIZE);
 	cr |= cr_width;
-- 
1.7.3.1


------------------------------------------------------------------------------
Download new Adobe(R) Flash(R) Builder(TM) 4
The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly 
Flex(R) Builder(TM)) enable the development of rich applications that run
across multiple browsers and platforms. Download your free trials today!
http://p.sf.net/sfu/adobe-dev2dev

[PATCH 28/28] Blackfin SPI: init early

[Mike Frysinger]

From: Michael Hennerich <michael.hennerich-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>

Some systems using this bus sometimes have very basic devices on them
such as regulators.  So we need to be loaded even earlier in case the
devices are used before userspace is loaded.  Therefore register in
subsys_initcall().

Signed-off-by: Michael Hennerich <michael.hennerich-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index bd18214..d17ab37 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -1466,7 +1466,7 @@ static int __init bfin_spi_init(void)
 {
 	return platform_driver_probe(&bfin_spi_driver, bfin_spi_probe);
 }
-module_init(bfin_spi_init);
+subsys_initcall(bfin_spi_init);
 
 static void __exit bfin_spi_exit(void)
 {
-- 
1.7.3.1


------------------------------------------------------------------------------
Download new Adobe(R) Flash(R) Builder(TM) 4
The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly 
Flex(R) Builder(TM)) enable the development of rich applications that run
across multiple browsers and platforms. Download your free trials today!
http://p.sf.net/sfu/adobe-dev2dev

Re: [PATCH 11/28] Blackfin SPI: convert struct names to something more logical

[Grant Likely]

On Sun, Oct 17, 2010 at 06:59:24PM -0400, Mike Frysinger wrote:
> The current structure names are a bit confusing as to what they represent,
> so use better names.
> 
> Reported-by: David Brownell <dbrownell-Rn4VEauK+AKRv+LV9MX5uipxlwaOVQ5f@public.gmane.org>
> Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
> ---
>  drivers/spi/spi_bfin5xx.c |  100 ++++++++++++++++++++++----------------------
>  1 files changed, 50 insertions(+), 50 deletions(-)
> 
> diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
> index b0de61a..9a1801b 100644
> --- a/drivers/spi/spi_bfin5xx.c
> +++ b/drivers/spi/spi_bfin5xx.c
> @@ -42,15 +42,15 @@ MODULE_LICENSE("GPL");
>  #define DONE_STATE	((void *)2)
>  #define ERROR_STATE	((void *)-1)
>  
> -struct driver_data;
> +struct master_data;
>  
>  struct transfer_ops {
> -	void (*write) (struct driver_data *);
> -	void (*read) (struct driver_data *);
> -	void (*duplex) (struct driver_data *);
> +	void (*write) (struct master_data *);
> +	void (*read) (struct master_data *);
> +	void (*duplex) (struct master_data *);
>  };
>  
> -struct driver_data {
> +struct master_data {

Or better yet, to protect against global collisions, bfin5xx_master perhaps?

>  	/* Driver model hookup */
>  	struct platform_device *pdev;
>  
> @@ -80,7 +80,7 @@ struct driver_data {
>  	/* Current message transfer state info */
>  	struct spi_message *cur_msg;
>  	struct spi_transfer *cur_transfer;
> -	struct chip_data *cur_chip;
> +	struct slave_data *cur_chip;
>  	size_t len_in_bytes;
>  	size_t len;
>  	void *tx;
> @@ -105,7 +105,7 @@ struct driver_data {
>  	const struct transfer_ops *ops;
>  };
>  
> -struct chip_data {
> +struct slave_data {

Ditto here.  bfin5xx_slave?

>  	u16 ctl_reg;
>  	u16 baud;
>  	u16 flag;
> @@ -123,9 +123,9 @@ struct chip_data {
>  };
>  
>  #define DEFINE_SPI_REG(reg, off) \
> -static inline u16 read_##reg(struct driver_data *drv_data) \
> +static inline u16 read_##reg(struct master_data *drv_data) \
>  	{ return bfin_read16(drv_data->regs_base + off); } \
> -static inline void write_##reg(struct driver_data *drv_data, u16 v) \
> +static inline void write_##reg(struct master_data *drv_data, u16 v) \
>  	{ bfin_write16(drv_data->regs_base + off, v); }
>  
>  DEFINE_SPI_REG(CTRL, 0x00)
> @@ -136,7 +136,7 @@ DEFINE_SPI_REG(RDBR, 0x10)
>  DEFINE_SPI_REG(BAUD, 0x14)
>  DEFINE_SPI_REG(SHAW, 0x18)
>  
> -static void bfin_spi_enable(struct driver_data *drv_data)
> +static void bfin_spi_enable(struct master_data *drv_data)
>  {
>  	u16 cr;
>  
> @@ -144,7 +144,7 @@ static void bfin_spi_enable(struct driver_data *drv_data)
>  	write_CTRL(drv_data, (cr | BIT_CTL_ENABLE));
>  }
>  
> -static void bfin_spi_disable(struct driver_data *drv_data)
> +static void bfin_spi_disable(struct master_data *drv_data)
>  {
>  	u16 cr;
>  
> @@ -167,7 +167,7 @@ static u16 hz_to_spi_baud(u32 speed_hz)
>  	return spi_baud;
>  }
>  
> -static int bfin_spi_flush(struct driver_data *drv_data)
> +static int bfin_spi_flush(struct master_data *drv_data)
>  {
>  	unsigned long limit = loops_per_jiffy << 1;
>  
> @@ -181,7 +181,7 @@ static int bfin_spi_flush(struct driver_data *drv_data)
>  }
>  
>  /* Chip select operation functions for cs_change flag */
> -static void bfin_spi_cs_active(struct driver_data *drv_data, struct chip_data *chip)
> +static void bfin_spi_cs_active(struct master_data *drv_data, struct slave_data *chip)
>  {
>  	if (likely(chip->chip_select_num)) {
>  		u16 flag = read_FLAG(drv_data);
> @@ -194,7 +194,7 @@ static void bfin_spi_cs_active(struct driver_data *drv_data, struct chip_data *c
>  	}
>  }
>  
> -static void bfin_spi_cs_deactive(struct driver_data *drv_data, struct chip_data *chip)
> +static void bfin_spi_cs_deactive(struct master_data *drv_data, struct slave_data *chip)
>  {
>  	if (likely(chip->chip_select_num)) {
>  		u16 flag = read_FLAG(drv_data);
> @@ -212,7 +212,7 @@ static void bfin_spi_cs_deactive(struct driver_data *drv_data, struct chip_data
>  }
>  
>  /* enable or disable the pin muxed by GPIO and SPI CS to work as SPI CS */
> -static inline void bfin_spi_cs_enable(struct driver_data *drv_data, struct chip_data *chip)
> +static inline void bfin_spi_cs_enable(struct master_data *drv_data, struct slave_data *chip)
>  {
>  	u16 flag = read_FLAG(drv_data);
>  
> @@ -221,7 +221,7 @@ static inline void bfin_spi_cs_enable(struct driver_data *drv_data, struct chip_
>  	write_FLAG(drv_data, flag);
>  }
>  
> -static inline void bfin_spi_cs_disable(struct driver_data *drv_data, struct chip_data *chip)
> +static inline void bfin_spi_cs_disable(struct master_data *drv_data, struct slave_data *chip)
>  {
>  	u16 flag = read_FLAG(drv_data);
>  
> @@ -231,9 +231,9 @@ static inline void bfin_spi_cs_disable(struct driver_data *drv_data, struct chip
>  }
>  
>  /* stop controller and re-config current chip*/
> -static void bfin_spi_restore_state(struct driver_data *drv_data)
> +static void bfin_spi_restore_state(struct master_data *drv_data)
>  {
> -	struct chip_data *chip = drv_data->cur_chip;
> +	struct slave_data *chip = drv_data->cur_chip;
>  
>  	/* Clear status and disable clock */
>  	write_STAT(drv_data, BIT_STAT_CLR);
> @@ -249,12 +249,12 @@ static void bfin_spi_restore_state(struct driver_data *drv_data)
>  }
>  
>  /* used to kick off transfer in rx mode and read unwanted RX data */
> -static inline void bfin_spi_dummy_read(struct driver_data *drv_data)
> +static inline void bfin_spi_dummy_read(struct master_data *drv_data)
>  {
>  	(void) read_RDBR(drv_data);
>  }
>  
> -static void bfin_spi_u8_writer(struct driver_data *drv_data)
> +static void bfin_spi_u8_writer(struct master_data *drv_data)
>  {
>  	/* clear RXS (we check for RXS inside the loop) */
>  	bfin_spi_dummy_read(drv_data);
> @@ -270,7 +270,7 @@ static void bfin_spi_u8_writer(struct driver_data *drv_data)
>  	}
>  }
>  
> -static void bfin_spi_u8_reader(struct driver_data *drv_data)
> +static void bfin_spi_u8_reader(struct master_data *drv_data)
>  {
>  	u16 tx_val = drv_data->cur_chip->idle_tx_val;
>  
> @@ -285,7 +285,7 @@ static void bfin_spi_u8_reader(struct driver_data *drv_data)
>  	}
>  }
>  
> -static void bfin_spi_u8_duplex(struct driver_data *drv_data)
> +static void bfin_spi_u8_duplex(struct master_data *drv_data)
>  {
>  	/* discard old RX data and clear RXS */
>  	bfin_spi_dummy_read(drv_data);
> @@ -304,7 +304,7 @@ static const struct transfer_ops bfin_transfer_ops_u8 = {
>  	.duplex = bfin_spi_u8_duplex,
>  };
>  
> -static void bfin_spi_u16_writer(struct driver_data *drv_data)
> +static void bfin_spi_u16_writer(struct master_data *drv_data)
>  {
>  	/* clear RXS (we check for RXS inside the loop) */
>  	bfin_spi_dummy_read(drv_data);
> @@ -321,7 +321,7 @@ static void bfin_spi_u16_writer(struct driver_data *drv_data)
>  	}
>  }
>  
> -static void bfin_spi_u16_reader(struct driver_data *drv_data)
> +static void bfin_spi_u16_reader(struct master_data *drv_data)
>  {
>  	u16 tx_val = drv_data->cur_chip->idle_tx_val;
>  
> @@ -337,7 +337,7 @@ static void bfin_spi_u16_reader(struct driver_data *drv_data)
>  	}
>  }
>  
> -static void bfin_spi_u16_duplex(struct driver_data *drv_data)
> +static void bfin_spi_u16_duplex(struct master_data *drv_data)
>  {
>  	/* discard old RX data and clear RXS */
>  	bfin_spi_dummy_read(drv_data);
> @@ -359,7 +359,7 @@ static const struct transfer_ops bfin_transfer_ops_u16 = {
>  };
>  
>  /* test if ther is more transfer to be done */
> -static void *bfin_spi_next_transfer(struct driver_data *drv_data)
> +static void *bfin_spi_next_transfer(struct master_data *drv_data)
>  {
>  	struct spi_message *msg = drv_data->cur_msg;
>  	struct spi_transfer *trans = drv_data->cur_transfer;
> @@ -378,9 +378,9 @@ static void *bfin_spi_next_transfer(struct driver_data *drv_data)
>   * caller already set message->status;
>   * dma and pio irqs are blocked give finished message back
>   */
> -static void bfin_spi_giveback(struct driver_data *drv_data)
> +static void bfin_spi_giveback(struct master_data *drv_data)
>  {
> -	struct chip_data *chip = drv_data->cur_chip;
> +	struct slave_data *chip = drv_data->cur_chip;
>  	struct spi_transfer *last_transfer;
>  	unsigned long flags;
>  	struct spi_message *msg;
> @@ -412,8 +412,8 @@ static void bfin_spi_giveback(struct driver_data *drv_data)
>  /* spi data irq handler */
>  static irqreturn_t bfin_spi_pio_irq_handler(int irq, void *dev_id)
>  {
> -	struct driver_data *drv_data = dev_id;
> -	struct chip_data *chip = drv_data->cur_chip;
> +	struct master_data *drv_data = dev_id;
> +	struct slave_data *chip = drv_data->cur_chip;
>  	struct spi_message *msg = drv_data->cur_msg;
>  	int n_bytes = drv_data->n_bytes;
>  
> @@ -484,8 +484,8 @@ static irqreturn_t bfin_spi_pio_irq_handler(int irq, void *dev_id)
>  
>  static irqreturn_t bfin_spi_dma_irq_handler(int irq, void *dev_id)
>  {
> -	struct driver_data *drv_data = dev_id;
> -	struct chip_data *chip = drv_data->cur_chip;
> +	struct master_data *drv_data = dev_id;
> +	struct slave_data *chip = drv_data->cur_chip;
>  	struct spi_message *msg = drv_data->cur_msg;
>  	unsigned long timeout;
>  	unsigned short dmastat = get_dma_curr_irqstat(drv_data->dma_channel);
> @@ -548,11 +548,11 @@ static irqreturn_t bfin_spi_dma_irq_handler(int irq, void *dev_id)
>  
>  static void bfin_spi_pump_transfers(unsigned long data)
>  {
> -	struct driver_data *drv_data = (struct driver_data *)data;
> +	struct master_data *drv_data = (struct master_data *)data;
>  	struct spi_message *message = NULL;
>  	struct spi_transfer *transfer = NULL;
>  	struct spi_transfer *previous = NULL;
> -	struct chip_data *chip = NULL;
> +	struct slave_data *chip = NULL;
>  	u8 width;
>  	u16 cr, dma_width, dma_config;
>  	u32 tranf_success = 1;
> @@ -872,10 +872,10 @@ static void bfin_spi_pump_transfers(unsigned long data)
>  /* pop a msg from queue and kick off real transfer */
>  static void bfin_spi_pump_messages(struct work_struct *work)
>  {
> -	struct driver_data *drv_data;
> +	struct master_data *drv_data;
>  	unsigned long flags;
>  
> -	drv_data = container_of(work, struct driver_data, pump_messages);
> +	drv_data = container_of(work, struct master_data, pump_messages);
>  
>  	/* Lock queue and check for queue work */
>  	spin_lock_irqsave(&drv_data->lock, flags);
> @@ -929,7 +929,7 @@ static void bfin_spi_pump_messages(struct work_struct *work)
>   */
>  static int bfin_spi_transfer(struct spi_device *spi, struct spi_message *msg)
>  {
> -	struct driver_data *drv_data = spi_master_get_devdata(spi->master);
> +	struct master_data *drv_data = spi_master_get_devdata(spi->master);
>  	unsigned long flags;
>  
>  	spin_lock_irqsave(&drv_data->lock, flags);
> @@ -974,8 +974,8 @@ static u16 ssel[][MAX_SPI_SSEL] = {
>  static int bfin_spi_setup(struct spi_device *spi)
>  {
>  	struct bfin5xx_spi_chip *chip_info;
> -	struct chip_data *chip = NULL;
> -	struct driver_data *drv_data = spi_master_get_devdata(spi->master);
> +	struct slave_data *chip = NULL;
> +	struct master_data *drv_data = spi_master_get_devdata(spi->master);
>  	int ret = -EINVAL;
>  
>  	if (spi->bits_per_word != 8 && spi->bits_per_word != 16)
> @@ -1155,8 +1155,8 @@ static int bfin_spi_setup(struct spi_device *spi)
>   */
>  static void bfin_spi_cleanup(struct spi_device *spi)
>  {
> -	struct chip_data *chip = spi_get_ctldata(spi);
> -	struct driver_data *drv_data = spi_master_get_devdata(spi->master);
> +	struct slave_data *chip = spi_get_ctldata(spi);
> +	struct master_data *drv_data = spi_master_get_devdata(spi->master);
>  
>  	if (!chip)
>  		return;
> @@ -1176,7 +1176,7 @@ static void bfin_spi_cleanup(struct spi_device *spi)
>  	spi_set_ctldata(spi, NULL);
>  }
>  
> -static inline int bfin_spi_init_queue(struct driver_data *drv_data)
> +static inline int bfin_spi_init_queue(struct master_data *drv_data)
>  {
>  	INIT_LIST_HEAD(&drv_data->queue);
>  	spin_lock_init(&drv_data->lock);
> @@ -1198,7 +1198,7 @@ static inline int bfin_spi_init_queue(struct driver_data *drv_data)
>  	return 0;
>  }
>  
> -static inline int bfin_spi_start_queue(struct driver_data *drv_data)
> +static inline int bfin_spi_start_queue(struct master_data *drv_data)
>  {
>  	unsigned long flags;
>  
> @@ -1220,7 +1220,7 @@ static inline int bfin_spi_start_queue(struct driver_data *drv_data)
>  	return 0;
>  }
>  
> -static inline int bfin_spi_stop_queue(struct driver_data *drv_data)
> +static inline int bfin_spi_stop_queue(struct master_data *drv_data)
>  {
>  	unsigned long flags;
>  	unsigned limit = 500;
> @@ -1249,7 +1249,7 @@ static inline int bfin_spi_stop_queue(struct driver_data *drv_data)
>  	return status;
>  }
>  
> -static inline int bfin_spi_destroy_queue(struct driver_data *drv_data)
> +static inline int bfin_spi_destroy_queue(struct master_data *drv_data)
>  {
>  	int status;
>  
> @@ -1267,14 +1267,14 @@ static int __init bfin_spi_probe(struct platform_device *pdev)
>  	struct device *dev = &pdev->dev;
>  	struct bfin5xx_spi_master *platform_info;
>  	struct spi_master *master;
> -	struct driver_data *drv_data = 0;
> +	struct master_data *drv_data = 0;
>  	struct resource *res;
>  	int status = 0;
>  
>  	platform_info = dev->platform_data;
>  
>  	/* Allocate master with space for drv_data */
> -	master = spi_alloc_master(dev, sizeof(struct driver_data) + 16);
> +	master = spi_alloc_master(dev, sizeof(struct master_data) + 16);
>  	if (!master) {
>  		dev_err(&pdev->dev, "can not alloc spi_master\n");
>  		return -ENOMEM;
> @@ -1377,7 +1377,7 @@ out_error_get_res:
>  /* stop hardware and remove the driver */
>  static int __devexit bfin_spi_remove(struct platform_device *pdev)
>  {
> -	struct driver_data *drv_data = platform_get_drvdata(pdev);
> +	struct master_data *drv_data = platform_get_drvdata(pdev);
>  	int status = 0;
>  
>  	if (!drv_data)
> @@ -1416,7 +1416,7 @@ static int __devexit bfin_spi_remove(struct platform_device *pdev)
>  #ifdef CONFIG_PM
>  static int bfin_spi_suspend(struct platform_device *pdev, pm_message_t state)
>  {
> -	struct driver_data *drv_data = platform_get_drvdata(pdev);
> +	struct master_data *drv_data = platform_get_drvdata(pdev);
>  	int status = 0;
>  
>  	status = bfin_spi_stop_queue(drv_data);
> @@ -1431,7 +1431,7 @@ static int bfin_spi_suspend(struct platform_device *pdev, pm_message_t state)
>  
>  static int bfin_spi_resume(struct platform_device *pdev)
>  {
> -	struct driver_data *drv_data = platform_get_drvdata(pdev);
> +	struct master_data *drv_data = platform_get_drvdata(pdev);
>  	int status = 0;
>  
>  	/* Enable the SPI interface */
> -- 
> 1.7.3.1
> 

------------------------------------------------------------------------------
Download new Adobe(R) Flash(R) Builder(TM) 4
The new Adobe(R) Flex(R) 4 and Flash(R) Builder(TM) 4 (formerly 
Flex(R) Builder(TM)) enable the development of rich applications that run
across multiple browsers and platforms. Download your free trials today!
http://p.sf.net/sfu/adobe-dev2dev

Re: [PATCH 14/28] Blackfin: SPI: expand SPI bitmasks

[Grant Likely]

On Sun, Oct 17, 2010 at 06:59:27PM -0400, Mike Frysinger wrote:
> Expand the BIT_CTL defines to use the naming convention of the hardware,
> and expand the masks to cover all documented bits.
> 
> Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
> ---
>  arch/blackfin/include/asm/bfin5xx_spi.h |   11 +++++++----
>  1 files changed, 7 insertions(+), 4 deletions(-)
> 
> diff --git a/arch/blackfin/include/asm/bfin5xx_spi.h b/arch/blackfin/include/asm/bfin5xx_spi.h
> index ee3ecb9..126d25e 100644
> --- a/arch/blackfin/include/asm/bfin5xx_spi.h
> +++ b/arch/blackfin/include/asm/bfin5xx_spi.h
> @@ -26,11 +26,14 @@
>  #define BIT_CTL_ENABLE      0x4000
>  #define BIT_CTL_OPENDRAIN   0x2000
>  #define BIT_CTL_MASTER      0x1000
> -#define BIT_CTL_POLAR       0x0800
> -#define BIT_CTL_PHASE       0x0400
> -#define BIT_CTL_BITORDER    0x0200
> +#define BIT_CTL_CPOL        0x0800
> +#define BIT_CTL_CPHA        0x0400
> +#define BIT_CTL_LSBF        0x0200
>  #define BIT_CTL_WORDSIZE    0x0100
> -#define BIT_CTL_MISOENABLE  0x0020
> +#define BIT_CTL_EMISO       0x0020
> +#define BIT_CTL_PSSE        0x0010
> +#define BIT_CTL_GM          0x0008
> +#define BIT_CTL_SZ          0x0004
>  #define BIT_CTL_RXMOD       0x0000
>  #define BIT_CTL_TXMOD       0x0001
>  #define BIT_CTL_TIMOD_DMA_TX 0x0003

Can I assume that these changed values are as-of-this-point unused?
Otherwise this patch has bisect issues.

g.

> -- 
> 1.7.3.1
> 

Re: [PATCH 11/28] Blackfin SPI: convert struct names to something more logical

[Mike Frysinger]

On Mon, Oct 18, 2010 at 02:02, Grant Likely wrote:
> On Sun, Oct 17, 2010 at 06:59:24PM -0400, Mike Frysinger wrote:
>> -struct driver_data {
>> +struct master_data {
>
> Or better yet, to protect against global collisions, bfin5xx_master perhaps?

i'd rather not.  there is too much "bfin5xx" stuff already which
shouldnt exist.  what collision could there possibly be ?
-mike

Re: [PATCH 14/28] Blackfin: SPI: expand SPI bitmasks

[Mike Frysinger]

On Mon, Oct 18, 2010 at 02:04, Grant Likely wrote:
> On Sun, Oct 17, 2010 at 06:59:27PM -0400, Mike Frysinger wrote:
>> Expand the BIT_CTL defines to use the naming convention of the hardware,
>> and expand the masks to cover all documented bits.
>>
>> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
>> ---
>>  arch/blackfin/include/asm/bfin5xx_spi.h |   11 +++++++----
>>  1 files changed, 7 insertions(+), 4 deletions(-)
>>
>> diff --git a/arch/blackfin/include/asm/bfin5xx_spi.h b/arch/blackfin/include/asm/bfin5xx_spi.h
>> index ee3ecb9..126d25e 100644
>> --- a/arch/blackfin/include/asm/bfin5xx_spi.h
>> +++ b/arch/blackfin/include/asm/bfin5xx_spi.h
>> @@ -26,11 +26,14 @@
>>  #define BIT_CTL_ENABLE      0x4000
>>  #define BIT_CTL_OPENDRAIN   0x2000
>>  #define BIT_CTL_MASTER      0x1000
>> -#define BIT_CTL_POLAR       0x0800
>> -#define BIT_CTL_PHASE       0x0400
>> -#define BIT_CTL_BITORDER    0x0200
>> +#define BIT_CTL_CPOL        0x0800
>> +#define BIT_CTL_CPHA        0x0400
>> +#define BIT_CTL_LSBF        0x0200
>>  #define BIT_CTL_WORDSIZE    0x0100
>> -#define BIT_CTL_MISOENABLE  0x0020
>> +#define BIT_CTL_EMISO       0x0020
>> +#define BIT_CTL_PSSE        0x0010
>> +#define BIT_CTL_GM          0x0008
>> +#define BIT_CTL_SZ          0x0004
>>  #define BIT_CTL_RXMOD       0x0000
>>  #define BIT_CTL_TXMOD       0x0001
>>  #define BIT_CTL_TIMOD_DMA_TX 0x0003
>
> Can I assume that these changed values are as-of-this-point unused?

if you mean the ones i'm deleting -> yes
-mike
_______________________________________________
Uclinux-dist-devel mailing list
Uclinux-dist-devel@blackfin.uclinux.org
https://blackfin.uclinux.org/mailman/listinfo/uclinux-dist-devel

Re: [PATCH 28/28] Blackfin SPI: init early

[Grant Likely]

On Sun, Oct 17, 2010 at 06:59:41PM -0400, Mike Frysinger wrote:
> From: Michael Hennerich <michael.hennerich-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
> 
> Some systems using this bus sometimes have very basic devices on them
> such as regulators.  So we need to be loaded even earlier in case the
> devices are used before userspace is loaded.  Therefore register in
> subsys_initcall().

This shouldn't have anything to do with userspace since regardless of
the initcall, all of this setup should be complete before userspace
starts.  Rather I expect it has to do with an earlier initcall wanting
to have the spi bus up earlier than module_initcall.  The description
of this patch seems wrong.

On that note, this is something that needs to be revisited.  Needing
to play these kind of games highlights a failure of the device model,
or the way that it is being used.  (The patch is okay; but it does
highlight some ugliness in the current kernel)

g.

> 
> Signed-off-by: Michael Hennerich <michael.hennerich-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
> Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
> ---
>  drivers/spi/spi_bfin5xx.c |    2 +-
>  1 files changed, 1 insertions(+), 1 deletions(-)
> 
> diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
> index bd18214..d17ab37 100644
> --- a/drivers/spi/spi_bfin5xx.c
> +++ b/drivers/spi/spi_bfin5xx.c
> @@ -1466,7 +1466,7 @@ static int __init bfin_spi_init(void)
>  {
>  	return platform_driver_probe(&bfin_spi_driver, bfin_spi_probe);
>  }
> -module_init(bfin_spi_init);
> +subsys_initcall(bfin_spi_init);
>  
>  static void __exit bfin_spi_exit(void)
>  {
> -- 
> 1.7.3.1
> 

Re: [PATCH 28/28] Blackfin SPI: init early

[Mike Frysinger]

On Mon, Oct 18, 2010 at 02:12, Grant Likely wrote:
> On Sun, Oct 17, 2010 at 06:59:41PM -0400, Mike Frysinger wrote:
>> From: Michael Hennerich <michael.hennerich@analog.com>
>>
>> Some systems using this bus sometimes have very basic devices on them
>> such as regulators.  So we need to be loaded even earlier in case the
>> devices are used before userspace is loaded.  Therefore register in
>> subsys_initcall().
>
> This shouldn't have anything to do with userspace since regardless of
> the initcall, all of this setup should be complete before userspace
> starts.  Rather I expect it has to do with an earlier initcall wanting
> to have the spi bus up earlier than module_initcall.  The description
> of this patch seems wrong.

probably.  it doesnt make the change wrong though.  many spi/i2c
busses do the same thing.

> On that note, this is something that needs to be revisited.  Needing
> to play these kind of games highlights a failure of the device model,
> or the way that it is being used.  (The patch is okay; but it does
> highlight some ugliness in the current kernel)

i agree, but i'm not about to embark on fixing these fundamental issues.
-mike
_______________________________________________
Uclinux-dist-devel mailing list
Uclinux-dist-devel@blackfin.uclinux.org
https://blackfin.uclinux.org/mailman/listinfo/uclinux-dist-devel

Re: [PATCH 11/28] Blackfin SPI: convert struct names to something more logical

[Grant Likely]

On Mon, Oct 18, 2010 at 02:10:17AM -0400, Mike Frysinger wrote:
> On Mon, Oct 18, 2010 at 02:02, Grant Likely wrote:
> > On Sun, Oct 17, 2010 at 06:59:24PM -0400, Mike Frysinger wrote:
> >> -struct driver_data {
> >> +struct master_data {
> >
> > Or better yet, to protect against global collisions, bfin5xx_master perhaps?
> 
> i'd rather not.  there is too much "bfin5xx" stuff already which
> shouldnt exist.  what collision could there possibly be ?
> -mike

For driver code, anything at the file scope has a potential conflict
with the global scope.  If any header in include/linux were to define
a "master_data" or a "slave_data" structure, (those are pretty generic
names, it is well within the realm of possibilities) then it would
conflict.

A second reason for doing this is it helps reviewers/readers identify
the driver specific symbols.

For any driver code that I pick up, I pretty much require that
symbols in the file scope have a driver-specific prefix.

Also, now that I've looking at the existing code, it looks like
bfin_spi_ is the prefix that should actually be used, instead of
bfin5xx_

g.

Re: [PATCH 28/28] Blackfin SPI: init early

[Grant Likely]

On Mon, Oct 18, 2010 at 02:14:28AM -0400, Mike Frysinger wrote:
> On Mon, Oct 18, 2010 at 02:12, Grant Likely wrote:
> > On Sun, Oct 17, 2010 at 06:59:41PM -0400, Mike Frysinger wrote:
> >> From: Michael Hennerich <michael.hennerich-OyLXuOCK7orQT0dZR+AlfA@public.gmane.org>
> >>
> >> Some systems using this bus sometimes have very basic devices on them
> >> such as regulators.  So we need to be loaded even earlier in case the
> >> devices are used before userspace is loaded.  Therefore register in
> >> subsys_initcall().
> >
> > This shouldn't have anything to do with userspace since regardless of
> > the initcall, all of this setup should be complete before userspace
> > starts.  Rather I expect it has to do with an earlier initcall wanting
> > to have the spi bus up earlier than module_initcall.  The description
> > of this patch seems wrong.
> 
> probably.  it doesnt make the change wrong though.  many spi/i2c
> busses do the same thing.

Not saying it does.  Just asking for the commit log to be changed.

> 
> > On that note, this is something that needs to be revisited.  Needing
> > to play these kind of games highlights a failure of the device model,
> > or the way that it is being used.  (The patch is okay; but it does
> > highlight some ugliness in the current kernel)
> 
> i agree, but i'm not about to embark on fixing these fundamental issues.

Indeed.  I'm certainly not asking you to.  Just thinking out loud.  :-)

g.

Re: [PATCH 11/28] Blackfin SPI: convert struct names to something more logical

[Mike Frysinger]

On Mon, Oct 18, 2010 at 02:20, Grant Likely wrote:
> On Mon, Oct 18, 2010 at 02:10:17AM -0400, Mike Frysinger wrote:
>> On Mon, Oct 18, 2010 at 02:02, Grant Likely wrote:
>> > On Sun, Oct 17, 2010 at 06:59:24PM -0400, Mike Frysinger wrote:
>> >> -struct driver_data {
>> >> +struct master_data {
>> >
>> > Or better yet, to protect against global collisions, bfin5xx_master perhaps?
>>
>> i'd rather not.  there is too much "bfin5xx" stuff already which
>> shouldnt exist.  what collision could there possibly be ?
>
> For driver code, anything at the file scope has a potential conflict
> with the global scope.  If any header in include/linux were to define
> a "master_data" or a "slave_data" structure, (those are pretty generic
> names, it is well within the realm of possibilities) then it would
> conflict.

i dont think generic names like that would be allowed in global space
for this exact reason.  ive already made sure all the data/function
symbols that are visible from a linkage stand point are properly
namespaced because unlike structures, those are externally visible by
tools such as kallsyms.

i'd really prefer to not have to redo all these patches considering
this one change will cascade into like 20 others.  i'd be a lot more
amendable to a patch on top of all of these that namespaces the
structs.
-mike
_______________________________________________
Uclinux-dist-devel mailing list
Uclinux-dist-devel@blackfin.uclinux.org
https://blackfin.uclinux.org/mailman/listinfo/uclinux-dist-devel

Re: [PATCH 00/28] Blackfin SPI updates for 2.6.36

[Grant Likely]

On Sun, Oct 17, 2010 at 06:59:13PM -0400, Mike Frysinger wrote:
> Quite a bit here, but these patches have been around for a while.  The
> reason they haven't been pushed up before was that some of the first
> changes introduced known bugs themselves and needed some manual fixing.
> 
> Also, while some files touch Blackfin headers in arch/blackfin/, I'd
> like to keep them in this series and merge through the SPI tree to keep
> conflict issues down, as well as possible breakage due to desync.
> 
> These are also available in my 'for-spi' branch of my git tree:
> 	git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin.git

On brief review, the series looks good with a couple of minor comments
(already sent).

For the spi branch that I push to Linus, I always use the prefix
spi/<driver-name>.  If the patches in your branch also use that
prefix, then I'd be happy to pull your tree directly instead of
committing the patches myself.  Otherwise, I need to commit them
manually.

I *might* pick these up for .36, but it is very late for picking up
stuff that hasn't had any linux-next exposure yet.

Thanks,
g.

> 
> Barry Song (6):
>   Blackfin SPI: fix CS handling
>   Blackfin SPI: redo GPIO CS handling
>   Blackfin SPI: save/restore state when suspending/resuming
>   Blackfin SPI: sync hardware state before reprogramming everything
>   Blackfin SPI: use dma_disable_irq_nosync() in irq handler
>   Blackfin SPI: warn when CS is driven by hardware (CPHA=0)
> 
> Bob Liu (1):
>   Blackfin SPI: check per-transfer bits_per_word
> 
> Daniel Mack (1):
>   Blackfin SPI: fix resources leakage
> 
> Michael Hennerich (1):
>   Blackfin SPI: init early
> 
> Mike Frysinger (13):
>   Blackfin SPI: drop custom cs_change_per_word support
>   Blackfin SPI: punt useless null read/write funcs
>   Blackfin SPI: fix up some unused/misleading comments
>   Blackfin SPI: convert queue run state to true/false
>   Blackfin SPI: convert read/write/duplex funcs to a dedicated ops
>     structure
>   Blackfin SPI: convert struct names to something more logical
>   Blackfin SPI: drop extra memory we don't need
>   Blackfin SPI: use the SPI namespaced bit names
>   Blackfin: SPI: expand SPI bitmasks
>   Blackfin SPI: push all size checks into the transfer function
>   Blackfin SPI: reset ctl_reg bits when setup is run again on a device
>   Blackfin SPI: combine duplicate SPI_CTL read/write logic
>   Blackfin SPI: reject unsupported SPI modes
> 
> Rob Maris (2):
>   Blackfin SPI: fix typo in comment
>   Blackfin SPI: cs should be always low when a new transfer begins
> 
> Sonic Zhang (1):
>   Blackfin SPI: work around anomaly 05000119
> 
> Wolfgang Muees (1):
>   Blackfin SPI: force sane master-mode state at boot
> 
> Yi Li (2):
>   Blackfin SPI: utilize the SPI interrupt in PIO mode
>   Blackfin SPI: use nosync when disabling the IRQ from the IRQ handler
> 
>  arch/blackfin/include/asm/bfin5xx_spi.h |   81 +---
>  drivers/spi/spi_bfin5xx.c               |  839 ++++++++++++++++---------------
>  2 files changed, 441 insertions(+), 479 deletions(-)
> 
> -- 
> 1.7.3.1
> 

Re: [PATCH 11/28] Blackfin SPI: convert struct names to something more logical

[Grant Likely]

On Mon, Oct 18, 2010 at 02:28:23AM -0400, Mike Frysinger wrote:
> On Mon, Oct 18, 2010 at 02:20, Grant Likely wrote:
> > On Mon, Oct 18, 2010 at 02:10:17AM -0400, Mike Frysinger wrote:
> >> On Mon, Oct 18, 2010 at 02:02, Grant Likely wrote:
> >> > On Sun, Oct 17, 2010 at 06:59:24PM -0400, Mike Frysinger wrote:
> >> >> -struct driver_data {
> >> >> +struct master_data {
> >> >
> >> > Or better yet, to protect against global collisions, bfin5xx_master perhaps?
> >>
> >> i'd rather not.  there is too much "bfin5xx" stuff already which
> >> shouldnt exist.  what collision could there possibly be ?
> >
> > For driver code, anything at the file scope has a potential conflict
> > with the global scope.  If any header in include/linux were to define
> > a "master_data" or a "slave_data" structure, (those are pretty generic
> > names, it is well within the realm of possibilities) then it would
> > conflict.
> 
> i dont think generic names like that would be allowed in global space
> for this exact reason.  ive already made sure all the data/function
> symbols that are visible from a linkage stand point are properly
> namespaced because unlike structures, those are externally visible by
> tools such as kallsyms.
> 
> i'd really prefer to not have to redo all these patches considering
> this one change will cascade into like 20 others.  i'd be a lot more
> amendable to a patch on top of all of these that namespaces the
> structs.
> -mike

I'm okay with a patch on top.

g.

Re: [PATCH 00/28] Blackfin SPI updates for 2.6.36

[Mike Frysinger]

On Mon, Oct 18, 2010 at 02:28, Grant Likely wrote:
> On Sun, Oct 17, 2010 at 06:59:13PM -0400, Mike Frysinger wrote:
>> Quite a bit here, but these patches have been around for a while.  The
>> reason they haven't been pushed up before was that some of the first
>> changes introduced known bugs themselves and needed some manual fixing.
>>
>> Also, while some files touch Blackfin headers in arch/blackfin/, I'd
>> like to keep them in this series and merge through the SPI tree to keep
>> conflict issues down, as well as possible breakage due to desync.
>>
>> These are also available in my 'for-spi' branch of my git tree:
>>       git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin.git
>
> On brief review, the series looks good with a couple of minor comments
> (already sent).
>
> For the spi branch that I push to Linus, I always use the prefix
> spi/<driver-name>.  If the patches in your branch also use that
> prefix, then I'd be happy to pull your tree directly instead of
> committing the patches myself.  Otherwise, I need to commit them
> manually.

merged patches thus far have used the convention i picked here, but i
dont have a problem with changing them.

> I *might* pick these up for .36, but it is very late for picking up
> stuff that hasn't had any linux-next exposure yet.

these issues have been around for so long that missing another 2.6.x
is fine.  as long as they're in 2.6.37 ;).
-mike
_______________________________________________
Uclinux-dist-devel mailing list
Uclinux-dist-devel@blackfin.uclinux.org
https://blackfin.uclinux.org/mailman/listinfo/uclinux-dist-devel

Re: [PATCH 00/28] Blackfin SPI updates for 2.6.36

[Mike Frysinger]

On Mon, Oct 18, 2010 at 02:34, Mike Frysinger wrote:
> On Mon, Oct 18, 2010 at 02:28, Grant Likely wrote:
>> I *might* pick these up for .36, but it is very late for picking up
>> stuff that hasn't had any linux-next exposure yet.
>
> these issues have been around for so long that missing another 2.6.x
> is fine.  as long as they're in 2.6.37 ;).

sorry, i noticed my cover letter summary.  i meant for it to say "2.6.37".
-mike
_______________________________________________
Uclinux-dist-devel mailing list
Uclinux-dist-devel@blackfin.uclinux.org
https://blackfin.uclinux.org/mailman/listinfo/uclinux-dist-devel

[PATCH 29/28] spi/bfin_spi: namespace local structs

[Mike Frysinger]

Signed-off-by: Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org>
---
 drivers/spi/spi_bfin5xx.c |  119 +++++++++++++++++++++++----------------------
 1 files changed, 61 insertions(+), 58 deletions(-)

diff --git a/drivers/spi/spi_bfin5xx.c b/drivers/spi/spi_bfin5xx.c
index d17ab37..ab483a0 100644
--- a/drivers/spi/spi_bfin5xx.c
+++ b/drivers/spi/spi_bfin5xx.c
@@ -1,7 +1,7 @@
 /*
  * Blackfin On-Chip SPI Driver
  *
- * Copyright 2004-2007 Analog Devices Inc.
+ * Copyright 2004-2010 Analog Devices Inc.
  *
  * Enter bugs at http://blackfin.uclinux.org/
  *
@@ -42,15 +42,15 @@ MODULE_LICENSE("GPL");
 #define DONE_STATE	((void *)2)
 #define ERROR_STATE	((void *)-1)
 
-struct master_data;
+struct bfin_spi_master_data;
 
-struct transfer_ops {
-	void (*write) (struct master_data *);
-	void (*read) (struct master_data *);
-	void (*duplex) (struct master_data *);
+struct bfin_spi_transfer_ops {
+	void (*write) (struct bfin_spi_master_data *);
+	void (*read) (struct bfin_spi_master_data *);
+	void (*duplex) (struct bfin_spi_master_data *);
 };
 
-struct master_data {
+struct bfin_spi_master_data {
 	/* Driver model hookup */
 	struct platform_device *pdev;
 
@@ -80,7 +80,7 @@ struct master_data {
 	/* Current message transfer state info */
 	struct spi_message *cur_msg;
 	struct spi_transfer *cur_transfer;
-	struct slave_data *cur_chip;
+	struct bfin_spi_slave_data *cur_chip;
 	size_t len_in_bytes;
 	size_t len;
 	void *tx;
@@ -105,10 +105,10 @@ struct master_data {
 	u16 flag_reg;
 
 	int cs_change;
-	const struct transfer_ops *ops;
+	const struct bfin_spi_transfer_ops *ops;
 };
 
-struct slave_data {
+struct bfin_spi_slave_data {
 	u16 ctl_reg;
 	u16 baud;
 	u16 flag;
@@ -119,13 +119,13 @@ struct slave_data {
 	u32 cs_gpio;
 	u16 idle_tx_val;
 	u8 pio_interrupt;	/* use spi data irq */
-	const struct transfer_ops *ops;
+	const struct bfin_spi_transfer_ops *ops;
 };
 
 #define DEFINE_SPI_REG(reg, off) \
-static inline u16 read_##reg(struct master_data *drv_data) \
+static inline u16 read_##reg(struct bfin_spi_master_data *drv_data) \
 	{ return bfin_read16(drv_data->regs_base + off); } \
-static inline void write_##reg(struct master_data *drv_data, u16 v) \
+static inline void write_##reg(struct bfin_spi_master_data *drv_data, u16 v) \
 	{ bfin_write16(drv_data->regs_base + off, v); }
 
 DEFINE_SPI_REG(CTRL, 0x00)
@@ -136,7 +136,7 @@ DEFINE_SPI_REG(RDBR, 0x10)
 DEFINE_SPI_REG(BAUD, 0x14)
 DEFINE_SPI_REG(SHAW, 0x18)
 
-static void bfin_spi_enable(struct master_data *drv_data)
+static void bfin_spi_enable(struct bfin_spi_master_data *drv_data)
 {
 	u16 cr;
 
@@ -144,7 +144,7 @@ static void bfin_spi_enable(struct master_data *drv_data)
 	write_CTRL(drv_data, (cr | BIT_CTL_ENABLE));
 }
 
-static void bfin_spi_disable(struct master_data *drv_data)
+static void bfin_spi_disable(struct bfin_spi_master_data *drv_data)
 {
 	u16 cr;
 
@@ -167,7 +167,7 @@ static u16 hz_to_spi_baud(u32 speed_hz)
 	return spi_baud;
 }
 
-static int bfin_spi_flush(struct master_data *drv_data)
+static int bfin_spi_flush(struct bfin_spi_master_data *drv_data)
 {
 	unsigned long limit = loops_per_jiffy << 1;
 
@@ -181,7 +181,7 @@ static int bfin_spi_flush(struct master_data *drv_data)
 }
 
 /* Chip select operation functions for cs_change flag */
-static void bfin_spi_cs_active(struct master_data *drv_data, struct slave_data *chip)
+static void bfin_spi_cs_active(struct bfin_spi_master_data *drv_data, struct bfin_spi_slave_data *chip)
 {
 	if (likely(chip->chip_select_num < MAX_CTRL_CS)) {
 		u16 flag = read_FLAG(drv_data);
@@ -194,7 +194,8 @@ static void bfin_spi_cs_active(struct master_data *drv_data, struct slave_data *
 	}
 }
 
-static void bfin_spi_cs_deactive(struct master_data *drv_data, struct slave_data *chip)
+static void bfin_spi_cs_deactive(struct bfin_spi_master_data *drv_data,
+                                 struct bfin_spi_slave_data *chip)
 {
 	if (likely(chip->chip_select_num < MAX_CTRL_CS)) {
 		u16 flag = read_FLAG(drv_data);
@@ -212,7 +213,8 @@ static void bfin_spi_cs_deactive(struct master_data *drv_data, struct slave_data
 }
 
 /* enable or disable the pin muxed by GPIO and SPI CS to work as SPI CS */
-static inline void bfin_spi_cs_enable(struct master_data *drv_data, struct slave_data *chip)
+static inline void bfin_spi_cs_enable(struct bfin_spi_master_data *drv_data,
+                                      struct bfin_spi_slave_data *chip)
 {
 	if (chip->chip_select_num < MAX_CTRL_CS) {
 		u16 flag = read_FLAG(drv_data);
@@ -223,7 +225,8 @@ static inline void bfin_spi_cs_enable(struct master_data *drv_data, struct slave
 	}
 }
 
-static inline void bfin_spi_cs_disable(struct master_data *drv_data, struct slave_data *chip)
+static inline void bfin_spi_cs_disable(struct bfin_spi_master_data *drv_data,
+                                       struct bfin_spi_slave_data *chip)
 {
 	if (chip->chip_select_num < MAX_CTRL_CS) {
 		u16 flag = read_FLAG(drv_data);
@@ -235,9 +238,9 @@ static inline void bfin_spi_cs_disable(struct master_data *drv_data, struct slav
 }
 
 /* stop controller and re-config current chip*/
-static void bfin_spi_restore_state(struct master_data *drv_data)
+static void bfin_spi_restore_state(struct bfin_spi_master_data *drv_data)
 {
-	struct slave_data *chip = drv_data->cur_chip;
+	struct bfin_spi_slave_data *chip = drv_data->cur_chip;
 
 	/* Clear status and disable clock */
 	write_STAT(drv_data, BIT_STAT_CLR);
@@ -255,12 +258,12 @@ static void bfin_spi_restore_state(struct master_data *drv_data)
 }
 
 /* used to kick off transfer in rx mode and read unwanted RX data */
-static inline void bfin_spi_dummy_read(struct master_data *drv_data)
+static inline void bfin_spi_dummy_read(struct bfin_spi_master_data *drv_data)
 {
 	(void) read_RDBR(drv_data);
 }
 
-static void bfin_spi_u8_writer(struct master_data *drv_data)
+static void bfin_spi_u8_writer(struct bfin_spi_master_data *drv_data)
 {
 	/* clear RXS (we check for RXS inside the loop) */
 	bfin_spi_dummy_read(drv_data);
@@ -276,7 +279,7 @@ static void bfin_spi_u8_writer(struct master_data *drv_data)
 	}
 }
 
-static void bfin_spi_u8_reader(struct master_data *drv_data)
+static void bfin_spi_u8_reader(struct bfin_spi_master_data *drv_data)
 {
 	u16 tx_val = drv_data->cur_chip->idle_tx_val;
 
@@ -291,7 +294,7 @@ static void bfin_spi_u8_reader(struct master_data *drv_data)
 	}
 }
 
-static void bfin_spi_u8_duplex(struct master_data *drv_data)
+static void bfin_spi_u8_duplex(struct bfin_spi_master_data *drv_data)
 {
 	/* discard old RX data and clear RXS */
 	bfin_spi_dummy_read(drv_data);
@@ -304,13 +307,13 @@ static void bfin_spi_u8_duplex(struct master_data *drv_data)
 	}
 }
 
-static const struct transfer_ops bfin_transfer_ops_u8 = {
+static const struct bfin_spi_transfer_ops bfin_bfin_spi_transfer_ops_u8 = {
 	.write  = bfin_spi_u8_writer,
 	.read   = bfin_spi_u8_reader,
 	.duplex = bfin_spi_u8_duplex,
 };
 
-static void bfin_spi_u16_writer(struct master_data *drv_data)
+static void bfin_spi_u16_writer(struct bfin_spi_master_data *drv_data)
 {
 	/* clear RXS (we check for RXS inside the loop) */
 	bfin_spi_dummy_read(drv_data);
@@ -327,7 +330,7 @@ static void bfin_spi_u16_writer(struct master_data *drv_data)
 	}
 }
 
-static void bfin_spi_u16_reader(struct master_data *drv_data)
+static void bfin_spi_u16_reader(struct bfin_spi_master_data *drv_data)
 {
 	u16 tx_val = drv_data->cur_chip->idle_tx_val;
 
@@ -343,7 +346,7 @@ static void bfin_spi_u16_reader(struct master_data *drv_data)
 	}
 }
 
-static void bfin_spi_u16_duplex(struct master_data *drv_data)
+static void bfin_spi_u16_duplex(struct bfin_spi_master_data *drv_data)
 {
 	/* discard old RX data and clear RXS */
 	bfin_spi_dummy_read(drv_data);
@@ -358,14 +361,14 @@ static void bfin_spi_u16_duplex(struct master_data *drv_data)
 	}
 }
 
-static const struct transfer_ops bfin_transfer_ops_u16 = {
+static const struct bfin_spi_transfer_ops bfin_bfin_spi_transfer_ops_u16 = {
 	.write  = bfin_spi_u16_writer,
 	.read   = bfin_spi_u16_reader,
 	.duplex = bfin_spi_u16_duplex,
 };
 
 /* test if there is more transfer to be done */
-static void *bfin_spi_next_transfer(struct master_data *drv_data)
+static void *bfin_spi_next_transfer(struct bfin_spi_master_data *drv_data)
 {
 	struct spi_message *msg = drv_data->cur_msg;
 	struct spi_transfer *trans = drv_data->cur_transfer;
@@ -384,9 +387,9 @@ static void *bfin_spi_next_transfer(struct master_data *drv_data)
  * caller already set message->status;
  * dma and pio irqs are blocked give finished message back
  */
-static void bfin_spi_giveback(struct master_data *drv_data)
+static void bfin_spi_giveback(struct bfin_spi_master_data *drv_data)
 {
-	struct slave_data *chip = drv_data->cur_chip;
+	struct bfin_spi_slave_data *chip = drv_data->cur_chip;
 	struct spi_transfer *last_transfer;
 	unsigned long flags;
 	struct spi_message *msg;
@@ -418,8 +421,8 @@ static void bfin_spi_giveback(struct master_data *drv_data)
 /* spi data irq handler */
 static irqreturn_t bfin_spi_pio_irq_handler(int irq, void *dev_id)
 {
-	struct master_data *drv_data = dev_id;
-	struct slave_data *chip = drv_data->cur_chip;
+	struct bfin_spi_master_data *drv_data = dev_id;
+	struct bfin_spi_slave_data *chip = drv_data->cur_chip;
 	struct spi_message *msg = drv_data->cur_msg;
 	int n_bytes = drv_data->n_bytes;
 
@@ -490,8 +493,8 @@ static irqreturn_t bfin_spi_pio_irq_handler(int irq, void *dev_id)
 
 static irqreturn_t bfin_spi_dma_irq_handler(int irq, void *dev_id)
 {
-	struct master_data *drv_data = dev_id;
-	struct slave_data *chip = drv_data->cur_chip;
+	struct bfin_spi_master_data *drv_data = dev_id;
+	struct bfin_spi_slave_data *chip = drv_data->cur_chip;
 	struct spi_message *msg = drv_data->cur_msg;
 	unsigned long timeout;
 	unsigned short dmastat = get_dma_curr_irqstat(drv_data->dma_channel);
@@ -554,11 +557,11 @@ static irqreturn_t bfin_spi_dma_irq_handler(int irq, void *dev_id)
 
 static void bfin_spi_pump_transfers(unsigned long data)
 {
-	struct master_data *drv_data = (struct master_data *)data;
+	struct bfin_spi_master_data *drv_data = (struct bfin_spi_master_data *)data;
 	struct spi_message *message = NULL;
 	struct spi_transfer *transfer = NULL;
 	struct spi_transfer *previous = NULL;
-	struct slave_data *chip = NULL;
+	struct bfin_spi_slave_data *chip = NULL;
 	unsigned int bits_per_word;
 	u16 cr, cr_width, dma_width, dma_config;
 	u32 tranf_success = 1;
@@ -643,12 +646,12 @@ static void bfin_spi_pump_transfers(unsigned long data)
 		drv_data->n_bytes = 1;
 		drv_data->len = transfer->len;
 		cr_width = 0;
-		drv_data->ops = &bfin_transfer_ops_u8;
+		drv_data->ops = &bfin_bfin_spi_transfer_ops_u8;
 	} else if (bits_per_word == 16) {
 		drv_data->n_bytes = 2;
 		drv_data->len = (transfer->len) >> 1;
 		cr_width = BIT_CTL_WORDSIZE;
-		drv_data->ops = &bfin_transfer_ops_u16;
+		drv_data->ops = &bfin_bfin_spi_transfer_ops_u16;
 	} else {
 		dev_err(&drv_data->pdev->dev, "transfer: unsupported bits_per_word\n");
 		message->status = -EINVAL;
@@ -661,7 +664,7 @@ static void bfin_spi_pump_transfers(unsigned long data)
 
 	dev_dbg(&drv_data->pdev->dev,
 		"transfer: drv_data->ops is %p, chip->ops is %p, u8_ops is %p\n",
-		drv_data->ops, chip->ops, &bfin_transfer_ops_u8);
+		drv_data->ops, chip->ops, &bfin_bfin_spi_transfer_ops_u8);
 
 	message->state = RUNNING_STATE;
 	dma_config = 0;
@@ -868,10 +871,10 @@ static void bfin_spi_pump_transfers(unsigned long data)
 /* pop a msg from queue and kick off real transfer */
 static void bfin_spi_pump_messages(struct work_struct *work)
 {
-	struct master_data *drv_data;
+	struct bfin_spi_master_data *drv_data;
 	unsigned long flags;
 
-	drv_data = container_of(work, struct master_data, pump_messages);
+	drv_data = container_of(work, struct bfin_spi_master_data, pump_messages);
 
 	/* Lock queue and check for queue work */
 	spin_lock_irqsave(&drv_data->lock, flags);
@@ -925,7 +928,7 @@ static void bfin_spi_pump_messages(struct work_struct *work)
  */
 static int bfin_spi_transfer(struct spi_device *spi, struct spi_message *msg)
 {
-	struct master_data *drv_data = spi_master_get_devdata(spi->master);
+	struct bfin_spi_master_data *drv_data = spi_master_get_devdata(spi->master);
 	unsigned long flags;
 
 	spin_lock_irqsave(&drv_data->lock, flags);
@@ -970,8 +973,8 @@ static u16 ssel[][MAX_SPI_SSEL] = {
 static int bfin_spi_setup(struct spi_device *spi)
 {
 	struct bfin5xx_spi_chip *chip_info;
-	struct slave_data *chip = NULL;
-	struct master_data *drv_data = spi_master_get_devdata(spi->master);
+	struct bfin_spi_slave_data *chip = NULL;
+	struct bfin_spi_master_data *drv_data = spi_master_get_devdata(spi->master);
 	u16 bfin_ctl_reg;
 	int ret = -EINVAL;
 
@@ -1152,8 +1155,8 @@ static int bfin_spi_setup(struct spi_device *spi)
  */
 static void bfin_spi_cleanup(struct spi_device *spi)
 {
-	struct slave_data *chip = spi_get_ctldata(spi);
-	struct master_data *drv_data = spi_master_get_devdata(spi->master);
+	struct bfin_spi_slave_data *chip = spi_get_ctldata(spi);
+	struct bfin_spi_master_data *drv_data = spi_master_get_devdata(spi->master);
 
 	if (!chip)
 		return;
@@ -1170,7 +1173,7 @@ static void bfin_spi_cleanup(struct spi_device *spi)
 	spi_set_ctldata(spi, NULL);
 }
 
-static inline int bfin_spi_init_queue(struct master_data *drv_data)
+static inline int bfin_spi_init_queue(struct bfin_spi_master_data *drv_data)
 {
 	INIT_LIST_HEAD(&drv_data->queue);
 	spin_lock_init(&drv_data->lock);
@@ -1192,7 +1195,7 @@ static inline int bfin_spi_init_queue(struct master_data *drv_data)
 	return 0;
 }
 
-static inline int bfin_spi_start_queue(struct master_data *drv_data)
+static inline int bfin_spi_start_queue(struct bfin_spi_master_data *drv_data)
 {
 	unsigned long flags;
 
@@ -1214,7 +1217,7 @@ static inline int bfin_spi_start_queue(struct master_data *drv_data)
 	return 0;
 }
 
-static inline int bfin_spi_stop_queue(struct master_data *drv_data)
+static inline int bfin_spi_stop_queue(struct bfin_spi_master_data *drv_data)
 {
 	unsigned long flags;
 	unsigned limit = 500;
@@ -1243,7 +1246,7 @@ static inline int bfin_spi_stop_queue(struct master_data *drv_data)
 	return status;
 }
 
-static inline int bfin_spi_destroy_queue(struct master_data *drv_data)
+static inline int bfin_spi_destroy_queue(struct bfin_spi_master_data *drv_data)
 {
 	int status;
 
@@ -1261,7 +1264,7 @@ static int __init bfin_spi_probe(struct platform_device *pdev)
 	struct device *dev = &pdev->dev;
 	struct bfin5xx_spi_master *platform_info;
 	struct spi_master *master;
-	struct master_data *drv_data;
+	struct bfin_spi_master_data *drv_data;
 	struct resource *res;
 	int status = 0;
 
@@ -1371,7 +1374,7 @@ out_error_get_res:
 /* stop hardware and remove the driver */
 static int __devexit bfin_spi_remove(struct platform_device *pdev)
 {
-	struct master_data *drv_data = platform_get_drvdata(pdev);
+	struct bfin_spi_master_data *drv_data = platform_get_drvdata(pdev);
 	int status = 0;
 
 	if (!drv_data)
@@ -1410,7 +1413,7 @@ static int __devexit bfin_spi_remove(struct platform_device *pdev)
 #ifdef CONFIG_PM
 static int bfin_spi_suspend(struct platform_device *pdev, pm_message_t state)
 {
-	struct master_data *drv_data = platform_get_drvdata(pdev);
+	struct bfin_spi_master_data *drv_data = platform_get_drvdata(pdev);
 	int status = 0;
 
 	status = bfin_spi_stop_queue(drv_data);
@@ -1431,7 +1434,7 @@ static int bfin_spi_suspend(struct platform_device *pdev, pm_message_t state)
 
 static int bfin_spi_resume(struct platform_device *pdev)
 {
-	struct master_data *drv_data = platform_get_drvdata(pdev);
+	struct bfin_spi_master_data *drv_data = platform_get_drvdata(pdev);
 	int status = 0;
 
 	write_CTRL(drv_data, drv_data->ctrl_reg);
-- 
1.7.3.1

Re: [PATCH 00/28] Blackfin SPI updates for 2.6.36

[Mike Frysinger]

On Mon, Oct 18, 2010 at 02:34, Mike Frysinger wrote:
> On Mon, Oct 18, 2010 at 02:28, Grant Likely wrote:
>> On Sun, Oct 17, 2010 at 06:59:13PM -0400, Mike Frysinger wrote:
>>> Quite a bit here, but these patches have been around for a while.  The
>>> reason they haven't been pushed up before was that some of the first
>>> changes introduced known bugs themselves and needed some manual fixing.
>>>
>>> Also, while some files touch Blackfin headers in arch/blackfin/, I'd
>>> like to keep them in this series and merge through the SPI tree to keep
>>> conflict issues down, as well as possible breakage due to desync.
>>>
>>> These are also available in my 'for-spi' branch of my git tree:
>>>       git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin.git
>>
>> On brief review, the series looks good with a couple of minor comments
>> (already sent).
>>
>> For the spi branch that I push to Linus, I always use the prefix
>> spi/<driver-name>.  If the patches in your branch also use that
>> prefix, then I'd be happy to pull your tree directly instead of
>> committing the patches myself.  Otherwise, I need to commit them
>> manually.
>
> merged patches thus far have used the convention i picked here, but i
> dont have a problem with changing them.

ive rewriitten the logs, addressed your feedback on all the other
patches, and pushed up the new for-spi branch if you want to double
check & pull.  i dont want to spam people with 30 patches where only
the summary changed ...
-mike
_______________________________________________
Uclinux-dist-devel mailing list
Uclinux-dist-devel@blackfin.uclinux.org
https://blackfin.uclinux.org/mailman/listinfo/uclinux-dist-devel

Re: [PATCH 00/28] Blackfin SPI updates for 2.6.36

[Grant Likely]

On Mon, Oct 18, 2010 at 12:37 AM, Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org> wrote:
> On Mon, Oct 18, 2010 at 02:34, Mike Frysinger wrote:
>> On Mon, Oct 18, 2010 at 02:28, Grant Likely wrote:
>>> I *might* pick these up for .36, but it is very late for picking up
>>> stuff that hasn't had any linux-next exposure yet.
>>
>> these issues have been around for so long that missing another 2.6.x
>> is fine.  as long as they're in 2.6.37 ;).
>
> sorry, i noticed my cover letter summary.  i meant for it to say "2.6.37".

Ugh.  yes, but *I* said .36 when I meant .37.  Gah.

g,

> -mike
>



-- 
Grant Likely, B.Sc., P.Eng.
Secret Lab Technologies Ltd.

Re: [PATCH 00/28] Blackfin SPI updates for 2.6.36

[Grant Likely]

On Mon, Oct 18, 2010 at 12:49 AM, Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org> wrote:
> On Mon, Oct 18, 2010 at 02:34, Mike Frysinger wrote:
>> On Mon, Oct 18, 2010 at 02:28, Grant Likely wrote:
>>> On Sun, Oct 17, 2010 at 06:59:13PM -0400, Mike Frysinger wrote:
>>>> Quite a bit here, but these patches have been around for a while.  The
>>>> reason they haven't been pushed up before was that some of the first
>>>> changes introduced known bugs themselves and needed some manual fixing.
>>>>
>>>> Also, while some files touch Blackfin headers in arch/blackfin/, I'd
>>>> like to keep them in this series and merge through the SPI tree to keep
>>>> conflict issues down, as well as possible breakage due to desync.
>>>>
>>>> These are also available in my 'for-spi' branch of my git tree:
>>>>       git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin.git
>>>
>>> On brief review, the series looks good with a couple of minor comments
>>> (already sent).
>>>
>>> For the spi branch that I push to Linus, I always use the prefix
>>> spi/<driver-name>.  If the patches in your branch also use that
>>> prefix, then I'd be happy to pull your tree directly instead of
>>> committing the patches myself.  Otherwise, I need to commit them
>>> manually.
>>
>> merged patches thus far have used the convention i picked here, but i
>> dont have a problem with changing them.

Not since I've been maintainer... all 11 months of it.  :-P

> ive rewriitten the logs, addressed your feedback on all the other
> patches, and pushed up the new for-spi branch if you want to double
> check & pull.  i dont want to spam people with 30 patches where only
> the summary changed ...

Wise man.  Let me look....  git.kernel.org is being slow...

Hmmm.  Still looks like the old branch (old prefix and no patch 29).
Probably just mirroring being slow.  I'll check again tomorrow
morning.

g.

Re: [PATCH 00/28] Blackfin SPI updates for 2.6.36

[Grant Likely]

On Mon, Oct 18, 2010 at 1:04 AM, Grant Likely <grant.likely-s3s/WqlpOiPyB63q8FvJNQ@public.gmane.org> wrote:
> On Mon, Oct 18, 2010 at 12:49 AM, Mike Frysinger <vapier-aBrp7R+bbdUdnm+yROfE0A@public.gmane.org> wrote:
>> ive rewriitten the logs, addressed your feedback on all the other
>> patches, and pushed up the new for-spi branch if you want to double
>> check & pull.  i dont want to spam people with 30 patches where only
>> the summary changed ...
>
> Wise man.  Let me look....  git.kernel.org is being slow...
>
> Hmmm.  Still looks like the old branch (old prefix and no patch 29).
> Probably just mirroring being slow.  I'll check again tomorrow
> morning.

Merged, thanks.

g.