* [PATCH v2 0/1] davinci: spi: replace existing driver
@ 2010-07-02 22:38 Brian Niebuhr
[not found] ` <1278110334-13943-1-git-send-email-bniebuhr-JaPwekKOx1yaMJb+Lgu22Q@public.gmane.org>
[not found] ` <002301cb1ce6$64fba3e0$2ef2eba0$@raj@ti.com>
0 siblings, 2 replies; 12+ messages in thread
From: Brian Niebuhr @ 2010-07-02 22:38 UTC (permalink / raw)
To: spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f
Cc: davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/
I have included all of the recommended changes in this version of the patch.
I also combined the patches into one patch to avoid bisecting issues. This
makes the diff on davinci_spi.c very large.
If people who are using this driver could test this version of the driver
and Ack it, I would appreciate it.
** NOTE **
This patch requires the EDMA patch at:
http://linux.davincidsp.com/pipermail/davinci-linux-open-source/2010-March/018022.html
which is queued waiting on another driver fix, for DMA mode to work correctly.
Brian Niebuhr (1):
davinci: spi: replace existing driver
arch/arm/mach-davinci/board-dm355-evm.c | 10 +
arch/arm/mach-davinci/board-dm355-leopard.c | 10 +
arch/arm/mach-davinci/board-dm365-evm.c | 10 +
arch/arm/mach-davinci/dm355.c | 12 +-
arch/arm/mach-davinci/dm365.c | 12 +-
arch/arm/mach-davinci/include/mach/spi.h | 37 +-
drivers/spi/davinci_spi.c | 1328 ++++++++++++---------------
7 files changed, 648 insertions(+), 771 deletions(-)
------------------------------------------------------------------------------
This SF.net email is sponsored by Sprint
What will you do first with EVO, the first 4G phone?
Visit sprint.com/first -- http://p.sf.net/sfu/sprint-com-first
^ permalink raw reply [flat|nested] 12+ messages in thread[parent not found: <1278110334-13943-1-git-send-email-bniebuhr-JaPwekKOx1yaMJb+Lgu22Q@public.gmane.org>]
* [PATCH v2 1/1] davinci: spi: replace existing driver [not found] ` <1278110334-13943-1-git-send-email-bniebuhr-JaPwekKOx1yaMJb+Lgu22Q@public.gmane.org> @ 2010-07-02 22:38 ` Brian Niebuhr [not found] ` <1278110334-13943-2-git-send-email-bniebuhr-JaPwekKOx1yaMJb+Lgu22Q@public.gmane.org> 2010-07-06 8:36 ` [PATCH v2 0/1] " Sudhakar Rajashekhara 2010-07-06 8:36 ` Sudhakar Rajashekhara 2 siblings, 1 reply; 12+ messages in thread From: Brian Niebuhr @ 2010-07-02 22:38 UTC (permalink / raw) To: spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f Cc: davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/ INTRODUCTION I have been working on a custom OMAP-L138 board that has multiple spi devices (seven) on one controller. These devices have a wide range of transfer parameters (speed, phase, polarity, internal and gpio chip selects). During my testing I found multiple errors in the davinci spi driver as a result of this complex setup. The primary issues were: 1. There is a race condition due to the SPIBUF read busy-waits for slow devices 2. I found some DMA transfer length errors under some conditions 3. The chip select code caused extra byte transfers (with no chip select active) due to writes to SPIDAT1 4. Several issues prevented using multiple SPI devices, especially the DMA code, as disucussed previously on the davinci list. The fixes to these problems were not simple. I ended up making fairly large changes to the driver, and those changes are contained in these patches. The full list of changes follows. CHANGE LIST 1. davinci_spi_chipelect() now performs both activation and deactivation of chip selects. This lets spi_bitbang fully control chip select activation, as intended by the SPI API. 2. Chip select activation does not cause extra writes to the SPI bus 3. Chip select activation does not use SPIDEF for control. This change will also allow for implementation of inverted (active high) chip selects in the future. 4. Added back gpio chip select capability from the old driver 5. Fixed prescale calculation for non-integer fractions of spi clock 6. Allow specification of SPI transfer parameters on a per-device (instead of per-controller) basis 7. Allow specification of polled, interrupt-based, or DMA operation on a per-device basis 8. Allow DMA with when more than one device is connected 9. Combined pio and dma txrx_bufs functions into one since they share large parts of their functionality, and to simplify item (8). 10. Use only SPIFMT0 to allow more than 4 devices TESTING I have tested the driver using a custom SPI stress test on my OMAP-L138-based board with three devices connected. I have tested configurations with all three devices polled, all three interrupt-based, all three DMA, and a mixture. I have compiled with the davinci_all_defconfig, but I don't have EVMs for the other davinci platforms to test with. Signed-off-by: Brian Niebuhr <bniebuhr-JaPwekKOx1yaMJb+Lgu22Q@public.gmane.org> --- arch/arm/mach-davinci/board-dm355-evm.c | 10 + arch/arm/mach-davinci/board-dm355-leopard.c | 10 + arch/arm/mach-davinci/board-dm365-evm.c | 10 + arch/arm/mach-davinci/dm355.c | 12 +- arch/arm/mach-davinci/dm365.c | 12 +- arch/arm/mach-davinci/include/mach/spi.h | 37 +- drivers/spi/davinci_spi.c | 1328 ++++++++++++--------------- 7 files changed, 648 insertions(+), 771 deletions(-) diff --git a/arch/arm/mach-davinci/board-dm355-evm.c b/arch/arm/mach-davinci/board-dm355-evm.c index a319101..d2e9f20 100644 --- a/arch/arm/mach-davinci/board-dm355-evm.c +++ b/arch/arm/mach-davinci/board-dm355-evm.c @@ -32,6 +32,7 @@ #include <mach/nand.h> #include <mach/mmc.h> #include <mach/usb.h> +#include <mach/spi.h> /* NOTE: this is geared for the standard config, with a socketed * 2 GByte Micron NAND (MT29F16G08FAA) using 128KB sectors. If you @@ -300,10 +301,19 @@ static struct spi_eeprom at25640a = { .flags = EE_ADDR2, }; +static struct davinci_spi_config at25640a_spi_cfg = { + .parity_enable = false, + .intr_level = 0, + .io_type = SPI_IO_TYPE_DMA, + .wdelay = 0, + .timer_disable = true, +}; + static struct spi_board_info dm355_evm_spi_info[] __initconst = { { .modalias = "at25", .platform_data = &at25640a, + .controller_data = &at25640a_spi_cfg, .max_speed_hz = 10 * 1000 * 1000, /* at 3v3 */ .bus_num = 0, .chip_select = 0, diff --git a/arch/arm/mach-davinci/board-dm355-leopard.c b/arch/arm/mach-davinci/board-dm355-leopard.c index f1d8132..63078dc 100644 --- a/arch/arm/mach-davinci/board-dm355-leopard.c +++ b/arch/arm/mach-davinci/board-dm355-leopard.c @@ -29,6 +29,7 @@ #include <mach/nand.h> #include <mach/mmc.h> #include <mach/usb.h> +#include <mach/spi.h> /* NOTE: this is geared for the standard config, with a socketed * 2 GByte Micron NAND (MT29F16G08FAA) using 128KB sectors. If you @@ -222,10 +223,19 @@ static struct spi_eeprom at25640a = { .flags = EE_ADDR2, }; +static struct davinci_spi_config at25640a_spi_cfg = { + .parity_enable = false, + .intr_level = 0, + .io_type = SPI_IO_TYPE_DMA, + .wdelay = 0, + .timer_disable = true, +}; + static struct spi_board_info dm355_leopard_spi_info[] __initconst = { { .modalias = "at25", .platform_data = &at25640a, + .controller_data = &at25640a_spi_cfg, .max_speed_hz = 10 * 1000 * 1000, /* at 3v3 */ .bus_num = 0, .chip_select = 0, diff --git a/arch/arm/mach-davinci/board-dm365-evm.c b/arch/arm/mach-davinci/board-dm365-evm.c index 5bb86b2..5bc3622 100644 --- a/arch/arm/mach-davinci/board-dm365-evm.c +++ b/arch/arm/mach-davinci/board-dm365-evm.c @@ -39,6 +39,7 @@ #include <mach/mmc.h> #include <mach/nand.h> #include <mach/keyscan.h> +#include <mach/spi.h> #include <media/tvp514x.h> @@ -579,10 +580,19 @@ static struct spi_eeprom at25640 = { .flags = EE_ADDR2, }; +static struct davinci_spi_config at25640_spi_cfg = { + .parity_enable = false, + .intr_level = 0, + .io_type = SPI_IO_TYPE_DMA, + .wdelay = 0, + .timer_disable = true, +}; + static struct spi_board_info dm365_evm_spi_info[] __initconst = { { .modalias = "at25", .platform_data = &at25640, + .controller_data = &at25640_spi_cfg, .max_speed_hz = 10 * 1000 * 1000, .bus_num = 0, .chip_select = 0, diff --git a/arch/arm/mach-davinci/dm355.c b/arch/arm/mach-davinci/dm355.c index 3834781..378d41c 100644 --- a/arch/arm/mach-davinci/dm355.c +++ b/arch/arm/mach-davinci/dm355.c @@ -397,27 +397,21 @@ static struct resource dm355_spi0_resources[] = { }, { .start = 17, - .flags = IORESOURCE_DMA, + .flags = IORESOURCE_DMA | IORESOURCE_DMA_RX_CHAN, }, { .start = 16, - .flags = IORESOURCE_DMA, + .flags = IORESOURCE_DMA | IORESOURCE_DMA_TX_CHAN, }, { .start = EVENTQ_1, - .flags = IORESOURCE_DMA, + .flags = IORESOURCE_DMA | IORESOURCE_DMA_EVENT_Q, }, }; static struct davinci_spi_platform_data dm355_spi0_pdata = { .version = SPI_VERSION_1, .num_chipselect = 2, - .clk_internal = 1, - .cs_hold = 1, - .intr_level = 0, - .poll_mode = 1, /* 0 -> interrupt mode 1-> polling mode */ - .c2tdelay = 0, - .t2cdelay = 0, }; static struct platform_device dm355_spi0_device = { .name = "spi_davinci", diff --git a/arch/arm/mach-davinci/dm365.c b/arch/arm/mach-davinci/dm365.c index 652f4b6..8e68f8c 100644 --- a/arch/arm/mach-davinci/dm365.c +++ b/arch/arm/mach-davinci/dm365.c @@ -625,12 +625,6 @@ static u64 dm365_spi0_dma_mask = DMA_BIT_MASK(32); static struct davinci_spi_platform_data dm365_spi0_pdata = { .version = SPI_VERSION_1, .num_chipselect = 2, - .clk_internal = 1, - .cs_hold = 1, - .intr_level = 0, - .poll_mode = 1, /* 0 -> interrupt mode 1-> polling mode */ - .c2tdelay = 0, - .t2cdelay = 0, }; static struct resource dm365_spi0_resources[] = { @@ -645,15 +639,15 @@ static struct resource dm365_spi0_resources[] = { }, { .start = 17, - .flags = IORESOURCE_DMA, + .flags = IORESOURCE_DMA | IORESOURCE_DMA_RX_CHAN, }, { .start = 16, - .flags = IORESOURCE_DMA, + .flags = IORESOURCE_DMA | IORESOURCE_DMA_TX_CHAN, }, { .start = EVENTQ_3, - .flags = IORESOURCE_DMA, + .flags = IORESOURCE_DMA | IORESOURCE_DMA_EVENT_Q, }, }; diff --git a/arch/arm/mach-davinci/include/mach/spi.h b/arch/arm/mach-davinci/include/mach/spi.h index 910efbf..b69a2f5 100644 --- a/arch/arm/mach-davinci/include/mach/spi.h +++ b/arch/arm/mach-davinci/include/mach/spi.h @@ -19,6 +19,13 @@ #ifndef __ARCH_ARM_DAVINCI_SPI_H #define __ARCH_ARM_DAVINCI_SPI_H +#define SPI_INTERN_CS 0xFF + +/* resource flags for IORESOURCE_DMA resources */ +#define IORESOURCE_DMA_RX_CHAN 0x01 +#define IORESOURCE_DMA_TX_CHAN 0x02 +#define IORESOURCE_DMA_EVENT_Q 0x04 + enum { SPI_VERSION_1, /* For DM355/DM365/DM6467 */ SPI_VERSION_2, /* For DA8xx */ @@ -26,19 +33,25 @@ enum { struct davinci_spi_platform_data { u8 version; - u8 num_chipselect; - u8 wdelay; - u8 odd_parity; - u8 parity_enable; - u8 wait_enable; - u8 timer_disable; - u8 clk_internal; - u8 cs_hold; + u16 num_chipselect; + u8 *chip_sel; +}; + +struct davinci_spi_config { + bool odd_parity; + bool parity_enable; u8 intr_level; - u8 poll_mode; - u8 use_dma; - u8 c2tdelay; - u8 t2cdelay; + u8 io_type; +#define SPI_IO_TYPE_INTR 0 +#define SPI_IO_TYPE_POLL 1 +#define SPI_IO_TYPE_DMA 2 + u8 bytes_per_word; + u8 wdelay; + bool timer_disable; + u8 c2t_delay; + u8 t2c_delay; + u8 t2e_delay; + u8 c2e_delay; }; #endif /* __ARCH_ARM_DAVINCI_SPI_H */ diff --git a/drivers/spi/davinci_spi.c b/drivers/spi/davinci_spi.c index b85090c..10d5c34 100644 --- a/drivers/spi/davinci_spi.c +++ b/drivers/spi/davinci_spi.c @@ -1,5 +1,6 @@ /* * Copyright (C) 2009 Texas Instruments. + * Copyright (C) 2010 EF Johnson Technologies * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -27,197 +28,218 @@ #include <linux/dma-mapping.h> #include <linux/spi/spi.h> #include <linux/spi/spi_bitbang.h> -#include <linux/slab.h> #include <mach/spi.h> #include <mach/edma.h> -#define SPI_NO_RESOURCE ((resource_size_t)-1) - -#define SPI_MAX_CHIPSELECT 2 - -#define CS_DEFAULT 0xFF - -#define SPI_BUFSIZ (SMP_CACHE_BYTES + 1) -#define DAVINCI_DMA_DATA_TYPE_S8 0x01 -#define DAVINCI_DMA_DATA_TYPE_S16 0x02 -#define DAVINCI_DMA_DATA_TYPE_S32 0x04 - -#define SPIFMT_PHASE_MASK BIT(16) -#define SPIFMT_POLARITY_MASK BIT(17) -#define SPIFMT_DISTIMER_MASK BIT(18) -#define SPIFMT_SHIFTDIR_MASK BIT(20) -#define SPIFMT_WAITENA_MASK BIT(21) -#define SPIFMT_PARITYENA_MASK BIT(22) -#define SPIFMT_ODD_PARITY_MASK BIT(23) -#define SPIFMT_WDELAY_MASK 0x3f000000u -#define SPIFMT_WDELAY_SHIFT 24 -#define SPIFMT_CHARLEN_MASK 0x0000001Fu +#define CS_DEFAULT 0xFF +#define SCS0_SELECT 0x01 +#define SCS1_SELECT 0x02 +#define SCS2_SELECT 0x04 +#define SCS3_SELECT 0x08 +#define SCS4_SELECT 0x10 +#define SCS5_SELECT 0x20 +#define SCS6_SELECT 0x40 +#define SCS7_SELECT 0x80 + +#define SPIFMT_PHASE_MASK BIT(16) +#define SPIFMT_POLARITY_MASK BIT(17) +#define SPIFMT_DISTIMER_MASK BIT(18) +#define SPIFMT_SHIFTDIR_MASK BIT(20) +#define SPIFMT_WAITENA_MASK BIT(21) +#define SPIFMT_PARITYENA_MASK BIT(22) +#define SPIFMT_ODD_PARITY_MASK BIT(23) +#define SPIFMT_WDELAY_MASK 0x3f000000u +#define SPIFMT_WDELAY_SHIFT 24 +#define SPIFMT_CHARLEN_MASK 0x0000001Fu +#define SPIFMT_PRESCALE_SHIFT 8 /* SPIGCR1 */ -#define SPIGCR1_SPIENA_MASK 0x01000000u +#define SPIGCR1_SPIENA_MASK BIT(24) +#define SPIGCR1_POWERDOWN_MASK BIT(8) /* SPIPC0 */ -#define SPIPC0_DIFUN_MASK BIT(11) /* MISO */ -#define SPIPC0_DOFUN_MASK BIT(10) /* MOSI */ -#define SPIPC0_CLKFUN_MASK BIT(9) /* CLK */ -#define SPIPC0_SPIENA_MASK BIT(8) /* nREADY */ -#define SPIPC0_EN1FUN_MASK BIT(1) -#define SPIPC0_EN0FUN_MASK BIT(0) - -#define SPIINT_MASKALL 0x0101035F -#define SPI_INTLVL_1 0x000001FFu -#define SPI_INTLVL_0 0x00000000u +#define SPIPC0_DIFUN_MASK BIT(11) /* MISO */ +#define SPIPC0_DOFUN_MASK BIT(10) /* MOSI */ +#define SPIPC0_CLKFUN_MASK BIT(9) /* CLK */ +#define SPIPC0_SPIENA_MASK BIT(8) /* nREADY */ +#define SPIPC0_EN1FUN_MASK BIT(1) +#define SPIPC0_EN0FUN_MASK BIT(0) + +#define SPIINT_MASKALL 0x0101035Fu +#define SPIINT_MASKINT 0x0000035Fu +#define SPI_INTLVL_1 0x000001FFu +#define SPI_INTLVL_0 0x00000000u /* SPIDAT1 */ +#define SPIDAT1_CSHOLD_MASK BIT(28) #define SPIDAT1_CSHOLD_SHIFT 28 +#define SPIDAT1_WDEL_MASK BIT(26) +#define SPIDAT1_CSNR_MASK 0x00FF0000u #define SPIDAT1_CSNR_SHIFT 16 +#define SPIDAT1_DFSEL_MASK (BIT(24 | BIT(25)) #define SPIGCR1_CLKMOD_MASK BIT(1) -#define SPIGCR1_MASTER_MASK BIT(0) +#define SPIGCR1_MASTER_MASK BIT(0) #define SPIGCR1_LOOPBACK_MASK BIT(16) /* SPIBUF */ -#define SPIBUF_TXFULL_MASK BIT(29) -#define SPIBUF_RXEMPTY_MASK BIT(31) +#define SPIBUF_TXFULL_MASK BIT(29) +#define SPIBUF_RXEMPTY_MASK BIT(31) + +/* SPIDELAY */ +#define SPIDELAY_C2TDELAY_MASK 0xFF000000u +#define SPIDELAY_C2TDELAY_SHIFT 24 +#define SPIDELAY_T2CDELAY_MASK 0x00FF0000u +#define SPIDELAY_T2CDELAY_SHIFT 16 +#define SPIDELAY_T2EDELAY_MASK 0x0000FF00u +#define SPIDELAY_T2EDELAY_SHIFT 8 +#define SPIDELAY_C2EDELAY_MASK 0x000000FFu +#define SPIDELAY_C2EDELAY_SHIFT 0 + +/* SPIDEF */ +#define SPIDEF_CSDEF_MASK 0x000000FFu /* Error Masks */ -#define SPIFLG_DLEN_ERR_MASK BIT(0) -#define SPIFLG_TIMEOUT_MASK BIT(1) -#define SPIFLG_PARERR_MASK BIT(2) -#define SPIFLG_DESYNC_MASK BIT(3) -#define SPIFLG_BITERR_MASK BIT(4) -#define SPIFLG_OVRRUN_MASK BIT(6) -#define SPIFLG_RX_INTR_MASK BIT(8) -#define SPIFLG_TX_INTR_MASK BIT(9) -#define SPIFLG_BUF_INIT_ACTIVE_MASK BIT(24) -#define SPIFLG_MASK (SPIFLG_DLEN_ERR_MASK \ - | SPIFLG_TIMEOUT_MASK | SPIFLG_PARERR_MASK \ - | SPIFLG_DESYNC_MASK | SPIFLG_BITERR_MASK \ - | SPIFLG_OVRRUN_MASK | SPIFLG_RX_INTR_MASK \ - | SPIFLG_TX_INTR_MASK \ - | SPIFLG_BUF_INIT_ACTIVE_MASK) - -#define SPIINT_DLEN_ERR_INTR BIT(0) -#define SPIINT_TIMEOUT_INTR BIT(1) -#define SPIINT_PARERR_INTR BIT(2) -#define SPIINT_DESYNC_INTR BIT(3) -#define SPIINT_BITERR_INTR BIT(4) -#define SPIINT_OVRRUN_INTR BIT(6) -#define SPIINT_RX_INTR BIT(8) -#define SPIINT_TX_INTR BIT(9) -#define SPIINT_DMA_REQ_EN BIT(16) -#define SPIINT_ENABLE_HIGHZ BIT(24) - -#define SPI_T2CDELAY_SHIFT 16 -#define SPI_C2TDELAY_SHIFT 24 - +#define SPIFLG_DLEN_ERR_MASK BIT(0) +#define SPIFLG_TIMEOUT_MASK BIT(1) +#define SPIFLG_PARERR_MASK BIT(2) +#define SPIFLG_DESYNC_MASK BIT(3) +#define SPIFLG_BITERR_MASK BIT(4) +#define SPIFLG_OVRRUN_MASK BIT(6) +#define SPIFLG_RX_INTR_MASK BIT(8) +#define SPIFLG_TX_INTR_MASK BIT(9) +#define SPIFLG_BUF_INIT_ACTIVE_MASK BIT(24) +#define SPIFLG_ERROR_MASK (SPIFLG_DLEN_ERR_MASK \ + | SPIFLG_TIMEOUT_MASK | SPIFLG_PARERR_MASK \ + | SPIFLG_DESYNC_MASK | SPIFLG_BITERR_MASK \ + | SPIFLG_OVRRUN_MASK) +#define SPIFLG_MASK (SPIFLG_ERROR_MASK \ + | SPIFLG_RX_INTR_MASK | SPIFLG_TX_INTR_MASK \ + | SPIFLG_BUF_INIT_ACTIVE_MASK) + +#define SPIINT_DLEN_ERR_INTR BIT(0) +#define SPIINT_TIMEOUT_INTR BIT(1) +#define SPIINT_PARERR_INTR BIT(2) +#define SPIINT_DESYNC_INTR BIT(3) +#define SPIINT_BITERR_INTR BIT(4) +#define SPIINT_OVRRUN_INTR BIT(6) +#define SPIINT_RX_INTR BIT(8) +#define SPIINT_TX_INTR BIT(9) +#define SPIINT_DMA_REQ_EN BIT(16) +#define SPIINT_ENABLE_HIGHZ BIT(24) + +#define SPI_T2CDELAY_SHIFT 16 +#define SPI_C2TDELAY_SHIFT 24 /* SPI Controller registers */ -#define SPIGCR0 0x00 -#define SPIGCR1 0x04 -#define SPIINT 0x08 -#define SPILVL 0x0c -#define SPIFLG 0x10 -#define SPIPC0 0x14 -#define SPIPC1 0x18 -#define SPIPC2 0x1c -#define SPIPC3 0x20 -#define SPIPC4 0x24 -#define SPIPC5 0x28 -#define SPIPC6 0x2c -#define SPIPC7 0x30 -#define SPIPC8 0x34 -#define SPIDAT0 0x38 -#define SPIDAT1 0x3c -#define SPIBUF 0x40 -#define SPIEMU 0x44 -#define SPIDELAY 0x48 -#define SPIDEF 0x4c -#define SPIFMT0 0x50 -#define SPIFMT1 0x54 -#define SPIFMT2 0x58 -#define SPIFMT3 0x5c -#define TGINTVEC0 0x60 -#define TGINTVEC1 0x64 - -struct davinci_spi_slave { - u32 cmd_to_write; - u32 clk_ctrl_to_write; - u32 bytes_per_word; - u8 active_cs; +#define SPIGCR0 0x00 +#define SPIGCR1 0x04 +#define SPIINT 0x08 +#define SPILVL 0x0c +#define SPIFLG 0x10 +#define SPIPC0 0x14 +#define SPIPC1 0x18 +#define SPIPC2 0x1c +#define SPIPC3 0x20 +#define SPIPC4 0x24 +#define SPIPC5 0x28 +#define SPIPC6 0x2c +#define SPIPC7 0x30 +#define SPIPC8 0x34 +#define SPIDAT0 0x38 +#define SPIDAT1 0x3c +#define SPIBUF 0x40 +#define SPIEMU 0x44 +#define SPIDELAY 0x48 +#define SPIDEF 0x4c +#define SPIFMT0 0x50 +#define SPIFMT1 0x54 +#define SPIFMT2 0x58 +#define SPIFMT3 0x5c +#define TGINTVEC0 0x60 +#define TGINTVEC1 0x64 + +#define SPI_BUFSIZ (SMP_CACHE_BYTES + 1) + +const char * const io_type_names[] = { + [SPI_IO_TYPE_INTR] = "Interrupt", + [SPI_IO_TYPE_POLL] = "Polled", + [SPI_IO_TYPE_DMA] = "DMA", }; /* We have 2 DMA channels per CS, one for RX and one for TX */ struct davinci_spi_dma { - int dma_tx_channel; - int dma_rx_channel; - int dma_tx_sync_dev; - int dma_rx_sync_dev; - enum dma_event_q eventq; - - struct completion dma_tx_completion; - struct completion dma_rx_completion; + int dma_tx_channel; + int dma_rx_channel; + int dma_tx_sync_dev; + int dma_rx_sync_dev; + int dummy_param_slot; + enum dma_event_q eventq; }; /* SPI Controller driver's private data. */ struct davinci_spi { - struct spi_bitbang bitbang; - struct clk *clk; - - u8 version; - resource_size_t pbase; - void __iomem *base; - size_t region_size; - u32 irq; - struct completion done; - - const void *tx; - void *rx; - u8 *tmp_buf; - int count; - struct davinci_spi_dma *dma_channels; - struct davinci_spi_platform_data *pdata; - - void (*get_rx)(u32 rx_data, struct davinci_spi *); - u32 (*get_tx)(struct davinci_spi *); - - struct davinci_spi_slave slave[SPI_MAX_CHIPSELECT]; + struct spi_bitbang bitbang; + struct clk *clk; + + u8 version; + resource_size_t pbase; + void __iomem *base; + size_t region_size; + u32 irq; + struct completion done; + + const void *tx; + void *rx; + u8 *tmp_buf; + int rcount; + int wcount; + u32 errors; + struct davinci_spi_dma dma_channels; + struct davinci_spi_platform_data *pdata; + + void (*get_rx)(u32 rx_data, struct davinci_spi *); + u32 (*get_tx)(struct davinci_spi *); }; -static unsigned use_dma; +#define DAVINCI_SPI_NO_RESOURCE ((resource_size_t)-1) static void davinci_spi_rx_buf_u8(u32 data, struct davinci_spi *davinci_spi) { - u8 *rx = davinci_spi->rx; - - *rx++ = (u8)data; - davinci_spi->rx = rx; + if (davinci_spi->rx) { + u8 *rx = davinci_spi->rx; + *rx++ = (u8)data; + davinci_spi->rx = rx; + } } static void davinci_spi_rx_buf_u16(u32 data, struct davinci_spi *davinci_spi) { - u16 *rx = davinci_spi->rx; - - *rx++ = (u16)data; - davinci_spi->rx = rx; + if (davinci_spi->rx) { + u16 *rx = davinci_spi->rx; + *rx++ = (u16)data; + davinci_spi->rx = rx; + } } static u32 davinci_spi_tx_buf_u8(struct davinci_spi *davinci_spi) { - u32 data; - const u8 *tx = davinci_spi->tx; - - data = *tx++; - davinci_spi->tx = tx; + u32 data = 0; + if (davinci_spi->tx) { + const u8 *tx = davinci_spi->tx; + data = *tx++; + davinci_spi->tx = tx; + } return data; } static u32 davinci_spi_tx_buf_u16(struct davinci_spi *davinci_spi) { - u32 data; - const u16 *tx = davinci_spi->tx; - - data = *tx++; - davinci_spi->tx = tx; + u32 data = 0; + if (davinci_spi->tx) { + const u16 *tx = davinci_spi->tx; + data = *tx++; + davinci_spi->tx = tx; + } return data; } @@ -237,26 +259,6 @@ static inline void clear_io_bits(void __iomem *addr, u32 bits) iowrite32(v, addr); } -static inline void set_fmt_bits(void __iomem *addr, u32 bits, int cs_num) -{ - set_io_bits(addr + SPIFMT0 + (0x4 * cs_num), bits); -} - -static inline void clear_fmt_bits(void __iomem *addr, u32 bits, int cs_num) -{ - clear_io_bits(addr + SPIFMT0 + (0x4 * cs_num), bits); -} - -static void davinci_spi_set_dma_req(const struct spi_device *spi, int enable) -{ - struct davinci_spi *davinci_spi = spi_master_get_devdata(spi->master); - - if (enable) - set_io_bits(davinci_spi->base + SPIINT, SPIINT_DMA_REQ_EN); - else - clear_io_bits(davinci_spi->base + SPIINT, SPIINT_DMA_REQ_EN); -} - /* * Interface to control the chip select signal */ @@ -264,28 +266,57 @@ static void davinci_spi_chipselect(struct spi_device *spi, int value) { struct davinci_spi *davinci_spi; struct davinci_spi_platform_data *pdata; - u32 data1_reg_val = 0; + u8 i, chip_sel = spi->chip_select; + u32 spidat1; + u16 spidat1_cfg; davinci_spi = spi_master_get_devdata(spi->master); pdata = davinci_spi->pdata; - /* - * Board specific chip select logic decides the polarity and cs - * line for the controller - */ - if (value == BITBANG_CS_INACTIVE) { - set_io_bits(davinci_spi->base + SPIDEF, CS_DEFAULT); - - data1_reg_val |= CS_DEFAULT << SPIDAT1_CSNR_SHIFT; - iowrite32(data1_reg_val, davinci_spi->base + SPIDAT1); + spidat1 = SPIDAT1_CSNR_MASK; + if (value == BITBANG_CS_ACTIVE) + spidat1 |= SPIDAT1_CSHOLD_MASK; + else + spidat1 |= SPIDAT1_WDEL_MASK; - while ((ioread32(davinci_spi->base + SPIBUF) - & SPIBUF_RXEMPTY_MASK) == 0) - cpu_relax(); + if (pdata->chip_sel == NULL) { + if (value == BITBANG_CS_ACTIVE) + spidat1 &= ~((0x1 << chip_sel) << SPIDAT1_CSNR_SHIFT); + } else { + for (i = 0; i < pdata->num_chipselect; i++) { + if (pdata->chip_sel[i] == SPI_INTERN_CS) { + if ((i == chip_sel) && + (value == BITBANG_CS_ACTIVE)) { + spidat1 &= ~((0x1 << chip_sel) + << SPIDAT1_CSNR_SHIFT); + } + } else { + if (value == BITBANG_CS_INACTIVE) + gpio_set_value(pdata->chip_sel[i], 1); + else if (i == chip_sel) + gpio_set_value(pdata->chip_sel[i], 0); + } + } } + + spidat1_cfg = spidat1 >> SPIDAT1_CSNR_SHIFT; + iowrite16(spidat1_cfg, davinci_spi->base + SPIDAT1 + 2); +} + +/* + * davinci_spi_get_prescale - Calculates the correct prescale value + * @max_speed_hz: the maximum rate the SPI clock can run at + * + * This function calculates the prescale value that generates a clock rate + * less than or equal to the specified maximum + */ +static inline u32 davinci_spi_get_prescale(struct davinci_spi *davinci_spi, + u32 max_speed_hz) +{ + return ((clk_get_rate(davinci_spi->clk) - 1) / max_speed_hz) & 0xff; } -/** +/* * davinci_spi_setup_transfer - This functions will determine transfer method * @spi: spi device on which data transfer to be done * @t: spi transfer in which transfer info is filled @@ -297,14 +328,15 @@ static void davinci_spi_chipselect(struct spi_device *spi, int value) static int davinci_spi_setup_transfer(struct spi_device *spi, struct spi_transfer *t) { - struct davinci_spi *davinci_spi; struct davinci_spi_platform_data *pdata; + struct davinci_spi_config *spi_cfg; u8 bits_per_word = 0; - u32 hz = 0, prescale = 0, clkspeed; + u32 hz = 0, spifmt = 0, prescale, delay = 0; davinci_spi = spi_master_get_devdata(spi->master); pdata = davinci_spi->pdata; + spi_cfg = spi->controller_data; if (t) { bits_per_word = t->bits_per_word; @@ -322,76 +354,112 @@ static int davinci_spi_setup_transfer(struct spi_device *spi, if (bits_per_word <= 8 && bits_per_word >= 2) { davinci_spi->get_rx = davinci_spi_rx_buf_u8; davinci_spi->get_tx = davinci_spi_tx_buf_u8; - davinci_spi->slave[spi->chip_select].bytes_per_word = 1; + spi_cfg->bytes_per_word = 1; } else if (bits_per_word <= 16 && bits_per_word >= 2) { davinci_spi->get_rx = davinci_spi_rx_buf_u16; davinci_spi->get_tx = davinci_spi_tx_buf_u16; - davinci_spi->slave[spi->chip_select].bytes_per_word = 2; + spi_cfg->bytes_per_word = 2; } else return -EINVAL; if (!hz) hz = spi->max_speed_hz; - clear_fmt_bits(davinci_spi->base, SPIFMT_CHARLEN_MASK, - spi->chip_select); - set_fmt_bits(davinci_spi->base, bits_per_word & 0x1f, - spi->chip_select); + prescale = davinci_spi_get_prescale(davinci_spi, hz); + spifmt |= (prescale << SPIFMT_PRESCALE_SHIFT); + + spifmt |= (bits_per_word & 0x1f); + + if (spi->mode & SPI_LSB_FIRST) + spifmt |= SPIFMT_SHIFTDIR_MASK; - clkspeed = clk_get_rate(davinci_spi->clk); - if (hz > clkspeed / 2) - prescale = 1 << 8; - if (hz < clkspeed / 256) - prescale = 255 << 8; - if (!prescale) - prescale = ((clkspeed / hz - 1) << 8) & 0x0000ff00; + if (spi->mode & SPI_CPOL) + spifmt |= SPIFMT_POLARITY_MASK; - clear_fmt_bits(davinci_spi->base, 0x0000ff00, spi->chip_select); - set_fmt_bits(davinci_spi->base, prescale, spi->chip_select); + if (!(spi->mode & SPI_CPHA)) + spifmt |= SPIFMT_PHASE_MASK; + + if (davinci_spi->version == SPI_VERSION_2) { + spifmt |= ((spi_cfg->wdelay << SPIFMT_WDELAY_SHIFT) + & SPIFMT_WDELAY_MASK); + + if (spi_cfg->odd_parity) + spifmt |= SPIFMT_ODD_PARITY_MASK; + + if (spi_cfg->parity_enable) + spifmt |= SPIFMT_PARITYENA_MASK; + + if (spi->mode & SPI_READY) { + spifmt |= SPIFMT_WAITENA_MASK; + delay |= (spi_cfg->t2e_delay + << SPIDELAY_T2EDELAY_SHIFT) + & SPIDELAY_T2EDELAY_MASK; + delay |= (spi_cfg->c2e_delay + << SPIDELAY_C2EDELAY_SHIFT) + & SPIDELAY_C2EDELAY_MASK; + } + + if (spi_cfg->timer_disable) { + spifmt |= SPIFMT_DISTIMER_MASK; + } else { + delay |= (spi_cfg->c2t_delay + << SPIDELAY_C2TDELAY_SHIFT) + & SPIDELAY_C2TDELAY_MASK; + delay |= (spi_cfg->t2c_delay + << SPIDELAY_T2CDELAY_SHIFT) + & SPIDELAY_T2CDELAY_MASK; + } + + iowrite32(delay, davinci_spi->base + SPIDELAY); + } + + iowrite32(spifmt, davinci_spi->base + SPIFMT0); + + if (spi_cfg->intr_level) + iowrite32(SPI_INTLVL_1, davinci_spi->base + SPILVL); + else + iowrite32(SPI_INTLVL_0, davinci_spi->base + SPILVL); + + if (spi->mode & SPI_LOOP) + set_io_bits(davinci_spi->base + SPIGCR1, + SPIGCR1_LOOPBACK_MASK); + else + clear_io_bits(davinci_spi->base + SPIGCR1, + SPIGCR1_LOOPBACK_MASK); return 0; } static void davinci_spi_dma_rx_callback(unsigned lch, u16 ch_status, void *data) { - struct spi_device *spi = (struct spi_device *)data; - struct davinci_spi *davinci_spi; + struct davinci_spi *davinci_spi = (struct davinci_spi *)data; struct davinci_spi_dma *davinci_spi_dma; struct davinci_spi_platform_data *pdata; - davinci_spi = spi_master_get_devdata(spi->master); - davinci_spi_dma = &(davinci_spi->dma_channels[spi->chip_select]); + davinci_spi_dma = &(davinci_spi->dma_channels); pdata = davinci_spi->pdata; + edma_stop(davinci_spi_dma->dma_rx_channel); + if (ch_status == DMA_COMPLETE) - edma_stop(davinci_spi_dma->dma_rx_channel); - else - edma_clean_channel(davinci_spi_dma->dma_rx_channel); + davinci_spi->rcount = 0; - complete(&davinci_spi_dma->dma_rx_completion); - /* We must disable the DMA RX request */ - davinci_spi_set_dma_req(spi, 0); + complete(&davinci_spi->done); } static void davinci_spi_dma_tx_callback(unsigned lch, u16 ch_status, void *data) { - struct spi_device *spi = (struct spi_device *)data; - struct davinci_spi *davinci_spi; + struct davinci_spi *davinci_spi = (struct davinci_spi *)data; struct davinci_spi_dma *davinci_spi_dma; struct davinci_spi_platform_data *pdata; - davinci_spi = spi_master_get_devdata(spi->master); - davinci_spi_dma = &(davinci_spi->dma_channels[spi->chip_select]); + davinci_spi_dma = &(davinci_spi->dma_channels); pdata = davinci_spi->pdata; - if (ch_status == DMA_COMPLETE) - edma_stop(davinci_spi_dma->dma_tx_channel); - else - edma_clean_channel(davinci_spi_dma->dma_tx_channel); + edma_stop(davinci_spi_dma->dma_tx_channel); - complete(&davinci_spi_dma->dma_tx_completion); - /* We must disable the DMA TX request */ - davinci_spi_set_dma_req(spi, 0); + if (ch_status == DMA_COMPLETE) + davinci_spi->wcount = 0; } static int davinci_spi_request_dma(struct spi_device *spi) @@ -403,33 +471,54 @@ static int davinci_spi_request_dma(struct spi_device *spi) int r; davinci_spi = spi_master_get_devdata(spi->master); - davinci_spi_dma = &davinci_spi->dma_channels[spi->chip_select]; + davinci_spi_dma = &davinci_spi->dma_channels; pdata = davinci_spi->pdata; sdev = davinci_spi->bitbang.master->dev.parent; r = edma_alloc_channel(davinci_spi_dma->dma_rx_sync_dev, - davinci_spi_dma_rx_callback, spi, + davinci_spi_dma_rx_callback, davinci_spi, davinci_spi_dma->eventq); if (r < 0) { - dev_dbg(sdev, "Unable to request DMA channel for SPI RX\n"); - return -EAGAIN; + dev_dbg(sdev, "Unable to request DMA channel for MibSPI RX\n"); + r = -EAGAIN; + goto rx_dma_failed; } davinci_spi_dma->dma_rx_channel = r; + r = edma_alloc_channel(davinci_spi_dma->dma_tx_sync_dev, - davinci_spi_dma_tx_callback, spi, + davinci_spi_dma_tx_callback, davinci_spi, davinci_spi_dma->eventq); if (r < 0) { - edma_free_channel(davinci_spi_dma->dma_rx_channel); - davinci_spi_dma->dma_rx_channel = -1; - dev_dbg(sdev, "Unable to request DMA channel for SPI TX\n"); - return -EAGAIN; + dev_dbg(sdev, "Unable to request DMA channel for MibSPI TX\n"); + r = -EAGAIN; + goto tx_dma_failed; } davinci_spi_dma->dma_tx_channel = r; + r = edma_alloc_slot(EDMA_CTLR(davinci_spi_dma->dma_tx_sync_dev), + EDMA_SLOT_ANY); + if (r < 0) { + dev_dbg(sdev, "Unable to request SPI DMA param slot\n"); + r = -EAGAIN; + goto param_failed; + } + davinci_spi_dma->dummy_param_slot = r; + edma_link(davinci_spi_dma->dummy_param_slot, + davinci_spi_dma->dummy_param_slot); + return 0; + +param_failed: + edma_free_channel(davinci_spi_dma->dma_tx_channel); + davinci_spi_dma->dma_tx_channel = -1; +tx_dma_failed: + edma_free_channel(davinci_spi_dma->dma_rx_channel); + davinci_spi_dma->dma_rx_channel = -1; +rx_dma_failed: + return r; } -/** +/* * davinci_spi_setup - This functions will set default transfer method * @spi: spi device on which data transfer to be done * @@ -438,129 +527,54 @@ static int davinci_spi_request_dma(struct spi_device *spi) static int davinci_spi_setup(struct spi_device *spi) { - int retval; + int retval = 0; struct davinci_spi *davinci_spi; - struct davinci_spi_dma *davinci_spi_dma; - struct device *sdev; + struct davinci_spi_dma *davinci_dma; + struct davinci_spi_platform_data *pdata; + struct davinci_spi_config *spi_cfg; + u32 prescale; davinci_spi = spi_master_get_devdata(spi->master); - sdev = davinci_spi->bitbang.master->dev.parent; + pdata = davinci_spi->pdata; + spi_cfg = (struct davinci_spi_config *)spi->controller_data; + davinci_dma = &(davinci_spi->dma_channels); /* if bits per word length is zero then set it default 8 */ if (!spi->bits_per_word) spi->bits_per_word = 8; - davinci_spi->slave[spi->chip_select].cmd_to_write = 0; - - if (use_dma && davinci_spi->dma_channels) { - davinci_spi_dma = &davinci_spi->dma_channels[spi->chip_select]; - - if ((davinci_spi_dma->dma_rx_channel == -1) - || (davinci_spi_dma->dma_tx_channel == -1)) { - retval = davinci_spi_request_dma(spi); - if (retval < 0) - return retval; - } - } + if (!(spi->mode & SPI_NO_CS)) { + if ((pdata->chip_sel == NULL) || + (pdata->chip_sel[spi->chip_select] == SPI_INTERN_CS)) + set_io_bits(davinci_spi->base + SPIPC0, + 1 << spi->chip_select); - /* - * SPI in DaVinci and DA8xx operate between - * 600 KHz and 50 MHz - */ - if (spi->max_speed_hz < 600000 || spi->max_speed_hz > 50000000) { - dev_dbg(sdev, "Operating frequency is not in acceptable " - "range\n"); - return -EINVAL; } - /* - * Set up SPIFMTn register, unique to this chipselect. - * - * NOTE: we could do all of these with one write. Also, some - * of the "version 2" features are found in chips that don't - * support all of them... - */ - if (spi->mode & SPI_LSB_FIRST) - set_fmt_bits(davinci_spi->base, SPIFMT_SHIFTDIR_MASK, - spi->chip_select); - else - clear_fmt_bits(davinci_spi->base, SPIFMT_SHIFTDIR_MASK, - spi->chip_select); + if (spi->mode & SPI_READY) + set_io_bits(davinci_spi->base + SPIPC0, SPIPC0_SPIENA_MASK); - if (spi->mode & SPI_CPOL) - set_fmt_bits(davinci_spi->base, SPIFMT_POLARITY_MASK, - spi->chip_select); - else - clear_fmt_bits(davinci_spi->base, SPIFMT_POLARITY_MASK, - spi->chip_select); + if (spi_cfg->io_type == SPI_IO_TYPE_DMA) { + davinci_dma = &(davinci_spi->dma_channels); - if (!(spi->mode & SPI_CPHA)) - set_fmt_bits(davinci_spi->base, SPIFMT_PHASE_MASK, - spi->chip_select); - else - clear_fmt_bits(davinci_spi->base, SPIFMT_PHASE_MASK, - spi->chip_select); + if ((davinci_dma->dma_tx_sync_dev == DAVINCI_SPI_NO_RESOURCE) || + (davinci_dma->dma_rx_sync_dev == DAVINCI_SPI_NO_RESOURCE) || + (davinci_dma->eventq == DAVINCI_SPI_NO_RESOURCE)) + spi_cfg->io_type = SPI_IO_TYPE_INTR; + else if ((davinci_dma->dma_rx_channel == -1) || + (davinci_dma->dma_tx_channel == -1)) + retval = davinci_spi_request_dma(spi); + } /* - * Version 1 hardware supports two basic SPI modes: - * - Standard SPI mode uses 4 pins, with chipselect - * - 3 pin SPI is a 4 pin variant without CS (SPI_NO_CS) - * (distinct from SPI_3WIRE, with just one data wire; - * or similar variants without MOSI or without MISO) - * - * Version 2 hardware supports an optional handshaking signal, - * so it can support two more modes: - * - 5 pin SPI variant is standard SPI plus SPI_READY - * - 4 pin with enable is (SPI_READY | SPI_NO_CS) + * Validate desired clock rate */ + prescale = davinci_spi_get_prescale(davinci_spi, spi->max_speed_hz); + if ((prescale < 2) || (prescale > 255)) + return -EINVAL; - if (davinci_spi->version == SPI_VERSION_2) { - clear_fmt_bits(davinci_spi->base, SPIFMT_WDELAY_MASK, - spi->chip_select); - set_fmt_bits(davinci_spi->base, - (davinci_spi->pdata->wdelay - << SPIFMT_WDELAY_SHIFT) - & SPIFMT_WDELAY_MASK, - spi->chip_select); - - if (davinci_spi->pdata->odd_parity) - set_fmt_bits(davinci_spi->base, - SPIFMT_ODD_PARITY_MASK, - spi->chip_select); - else - clear_fmt_bits(davinci_spi->base, - SPIFMT_ODD_PARITY_MASK, - spi->chip_select); - - if (davinci_spi->pdata->parity_enable) - set_fmt_bits(davinci_spi->base, - SPIFMT_PARITYENA_MASK, - spi->chip_select); - else - clear_fmt_bits(davinci_spi->base, - SPIFMT_PARITYENA_MASK, - spi->chip_select); - - if (davinci_spi->pdata->wait_enable) - set_fmt_bits(davinci_spi->base, - SPIFMT_WAITENA_MASK, - spi->chip_select); - else - clear_fmt_bits(davinci_spi->base, - SPIFMT_WAITENA_MASK, - spi->chip_select); - - if (davinci_spi->pdata->timer_disable) - set_fmt_bits(davinci_spi->base, - SPIFMT_DISTIMER_MASK, - spi->chip_select); - else - clear_fmt_bits(davinci_spi->base, - SPIFMT_DISTIMER_MASK, - spi->chip_select); - } - - retval = davinci_spi_setup_transfer(spi, NULL); + dev_info(&spi->dev, "DaVinci SPI driver in %s mode\n", + io_type_names[spi_cfg->io_type]); return retval; } @@ -569,50 +583,19 @@ static void davinci_spi_cleanup(struct spi_device *spi) { struct davinci_spi *davinci_spi = spi_master_get_devdata(spi->master); struct davinci_spi_dma *davinci_spi_dma; + struct davinci_spi_platform_data *pdata; - davinci_spi_dma = &davinci_spi->dma_channels[spi->chip_select]; - - if (use_dma && davinci_spi->dma_channels) { - davinci_spi_dma = &davinci_spi->dma_channels[spi->chip_select]; - - if ((davinci_spi_dma->dma_rx_channel != -1) - && (davinci_spi_dma->dma_tx_channel != -1)) { - edma_free_channel(davinci_spi_dma->dma_tx_channel); - edma_free_channel(davinci_spi_dma->dma_rx_channel); - } - } -} - -static int davinci_spi_bufs_prep(struct spi_device *spi, - struct davinci_spi *davinci_spi) -{ - int op_mode = 0; - - /* - * REVISIT unless devices disagree about SPI_LOOP or - * SPI_READY (SPI_NO_CS only allows one device!), this - * should not need to be done before each message... - * optimize for both flags staying cleared. - */ - - op_mode = SPIPC0_DIFUN_MASK - | SPIPC0_DOFUN_MASK - | SPIPC0_CLKFUN_MASK; - if (!(spi->mode & SPI_NO_CS)) - op_mode |= 1 << spi->chip_select; - if (spi->mode & SPI_READY) - op_mode |= SPIPC0_SPIENA_MASK; + davinci_spi_dma = &davinci_spi->dma_channels; + pdata = davinci_spi->pdata; - iowrite32(op_mode, davinci_spi->base + SPIPC0); + if (davinci_spi_dma->dma_rx_channel != -1) + edma_free_channel(davinci_spi_dma->dma_rx_channel); - if (spi->mode & SPI_LOOP) - set_io_bits(davinci_spi->base + SPIGCR1, - SPIGCR1_LOOPBACK_MASK); - else - clear_io_bits(davinci_spi->base + SPIGCR1, - SPIGCR1_LOOPBACK_MASK); + if (davinci_spi_dma->dma_tx_channel != -1) + edma_free_channel(davinci_spi_dma->dma_tx_channel); - return 0; + if (davinci_spi_dma->dummy_param_slot != -1) + edma_free_slot(davinci_spi_dma->dummy_param_slot); } static int davinci_spi_check_error(struct davinci_spi *davinci_spi, @@ -659,356 +642,248 @@ static int davinci_spi_check_error(struct davinci_spi *davinci_spi, return 0; } -/** - * davinci_spi_bufs - functions which will handle transfer data - * @spi: spi device on which data transfer to be done - * @t: spi transfer in which transfer info is filled +/* + * davinci_spi_process_events - check for and handle any SPI controller events + * @davinci_spi - the controller data * - * This function will put data to be transferred into data register - * of SPI controller and then wait until the completion will be marked - * by the IRQ Handler. + * This function will check the SPIFLG register and handle any events that are + * detected there */ -static int davinci_spi_bufs_pio(struct spi_device *spi, struct spi_transfer *t) +static int davinci_spi_process_events(struct davinci_spi *davinci_spi) { - struct davinci_spi *davinci_spi; - int int_status, count, ret; - u8 conv, tmp; - u32 tx_data, data1_reg_val; - u32 buf_val, flg_val; - struct davinci_spi_platform_data *pdata; - - davinci_spi = spi_master_get_devdata(spi->master); - pdata = davinci_spi->pdata; - - davinci_spi->tx = t->tx_buf; - davinci_spi->rx = t->rx_buf; - - /* convert len to words based on bits_per_word */ - conv = davinci_spi->slave[spi->chip_select].bytes_per_word; - davinci_spi->count = t->len / conv; - - INIT_COMPLETION(davinci_spi->done); - - ret = davinci_spi_bufs_prep(spi, davinci_spi); - if (ret) - return ret; - - /* Enable SPI */ - set_io_bits(davinci_spi->base + SPIGCR1, SPIGCR1_SPIENA_MASK); - - iowrite32(0 | (pdata->c2tdelay << SPI_C2TDELAY_SHIFT) | - (pdata->t2cdelay << SPI_T2CDELAY_SHIFT), - davinci_spi->base + SPIDELAY); - - count = davinci_spi->count; - data1_reg_val = pdata->cs_hold << SPIDAT1_CSHOLD_SHIFT; - tmp = ~(0x1 << spi->chip_select); - - clear_io_bits(davinci_spi->base + SPIDEF, ~tmp); - - data1_reg_val |= tmp << SPIDAT1_CSNR_SHIFT; - - while ((ioread32(davinci_spi->base + SPIBUF) - & SPIBUF_RXEMPTY_MASK) == 0) - cpu_relax(); - - /* Determine the command to execute READ or WRITE */ - if (t->tx_buf) { - clear_io_bits(davinci_spi->base + SPIINT, SPIINT_MASKALL); - - while (1) { - tx_data = davinci_spi->get_tx(davinci_spi); - - data1_reg_val &= ~(0xFFFF); - data1_reg_val |= (0xFFFF & tx_data); - - buf_val = ioread32(davinci_spi->base + SPIBUF); - if ((buf_val & SPIBUF_TXFULL_MASK) == 0) { - iowrite32(data1_reg_val, - davinci_spi->base + SPIDAT1); - - count--; - } - while (ioread32(davinci_spi->base + SPIBUF) - & SPIBUF_RXEMPTY_MASK) - cpu_relax(); - - /* getting the returned byte */ - if (t->rx_buf) { - buf_val = ioread32(davinci_spi->base + SPIBUF); - davinci_spi->get_rx(buf_val, davinci_spi); - } - if (count <= 0) - break; - } - } else { - if (pdata->poll_mode) { - while (1) { - /* keeps the serial clock going */ - if ((ioread32(davinci_spi->base + SPIBUF) - & SPIBUF_TXFULL_MASK) == 0) - iowrite32(data1_reg_val, - davinci_spi->base + SPIDAT1); - - while (ioread32(davinci_spi->base + SPIBUF) & - SPIBUF_RXEMPTY_MASK) - cpu_relax(); - - flg_val = ioread32(davinci_spi->base + SPIFLG); - buf_val = ioread32(davinci_spi->base + SPIBUF); - - davinci_spi->get_rx(buf_val, davinci_spi); - - count--; - if (count <= 0) - break; - } - } else { /* Receive in Interrupt mode */ - int i; - - for (i = 0; i < davinci_spi->count; i++) { - set_io_bits(davinci_spi->base + SPIINT, - SPIINT_BITERR_INTR - | SPIINT_OVRRUN_INTR - | SPIINT_RX_INTR); - - iowrite32(data1_reg_val, - davinci_spi->base + SPIDAT1); - - while (ioread32(davinci_spi->base + SPIINT) & - SPIINT_RX_INTR) - cpu_relax(); - } - iowrite32((data1_reg_val & 0x0ffcffff), - davinci_spi->base + SPIDAT1); - } + u32 status, tx_data, rx_data, spidat1; + u8 tx_word = 0; + + status = ioread32(davinci_spi->base + SPIFLG); + + if ((davinci_spi->version == SPI_VERSION_2) && + (likely(status & SPIFLG_TX_INTR_MASK)) && + (likely(davinci_spi->wcount > 0))) + tx_word = 1; + + if (likely(status & SPIFLG_RX_INTR_MASK)) { + rx_data = ioread32(davinci_spi->base + SPIBUF) & 0xFFFF; + davinci_spi->get_rx(rx_data, davinci_spi); + davinci_spi->rcount--; + if ((davinci_spi->version != SPI_VERSION_2) && + (likely(davinci_spi->wcount > 0))) + tx_word = 1; } - /* - * Check for bit error, desync error,parity error,timeout error and - * receive overflow errors - */ - int_status = ioread32(davinci_spi->base + SPIFLG); - - ret = davinci_spi_check_error(davinci_spi, int_status); - if (ret != 0) - return ret; + if (unlikely(status & SPIFLG_ERROR_MASK)) { + davinci_spi->errors = (status & SPIFLG_ERROR_MASK); + return -1; + } - /* SPI Framework maintains the count only in bytes so convert back */ - davinci_spi->count *= conv; + if (likely(tx_word)) { + spidat1 = ioread32(davinci_spi->base + SPIDAT1); + davinci_spi->wcount--; + tx_data = davinci_spi->get_tx(davinci_spi); + spidat1 &= 0xFFFF0000; + spidat1 |= (tx_data & 0xFFFF); + iowrite32(spidat1, davinci_spi->base + SPIDAT1); + } - return t->len; + return 0; } -#define DAVINCI_DMA_DATA_TYPE_S8 0x01 -#define DAVINCI_DMA_DATA_TYPE_S16 0x02 -#define DAVINCI_DMA_DATA_TYPE_S32 0x04 - -static int davinci_spi_bufs_dma(struct spi_device *spi, struct spi_transfer *t) +/* + * davinci_spi_txrx_bufs - function which will handle transfer data + * @spi: spi device on which data transfer to be done + * @t: spi transfer in which transfer info is filled + * + * This function will put data to be transferred into data register + * of SPI controller and then wait until the completion will be marked + * by the IRQ Handler. + */ +static int davinci_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t) { struct davinci_spi *davinci_spi; - int int_status = 0; - int count, temp_count; - u8 conv = 1; - u8 tmp; - u32 data1_reg_val; - struct davinci_spi_dma *davinci_spi_dma; - int word_len, data_type, ret; - unsigned long tx_reg, rx_reg; + int data_type, ret = 0; + u32 tx_data, spidat1; + u16 tx_buf_count = 0, rx_buf_count = 0; + struct davinci_spi_config *spi_cfg; struct davinci_spi_platform_data *pdata; + struct davinci_spi_dma *davinci_dma; struct device *sdev; + dma_addr_t tx_reg, rx_reg; + void *tx_buf, *rx_buf; + struct edmacc_param rx_param, tx_param; davinci_spi = spi_master_get_devdata(spi->master); pdata = davinci_spi->pdata; - sdev = davinci_spi->bitbang.master->dev.parent; - - davinci_spi_dma = &davinci_spi->dma_channels[spi->chip_select]; - - tx_reg = (unsigned long)davinci_spi->pbase + SPIDAT1; - rx_reg = (unsigned long)davinci_spi->pbase + SPIBUF; + spi_cfg = (struct davinci_spi_config *)spi->controller_data; + davinci_dma = &(davinci_spi->dma_channels); davinci_spi->tx = t->tx_buf; davinci_spi->rx = t->rx_buf; + davinci_spi->wcount = t->len / spi_cfg->bytes_per_word; + davinci_spi->rcount = davinci_spi->wcount; + davinci_spi->errors = 0; - /* convert len to words based on bits_per_word */ - conv = davinci_spi->slave[spi->chip_select].bytes_per_word; - davinci_spi->count = t->len / conv; - - INIT_COMPLETION(davinci_spi->done); + spidat1 = ioread32(davinci_spi->base + SPIDAT1); - init_completion(&davinci_spi_dma->dma_rx_completion); - init_completion(&davinci_spi_dma->dma_tx_completion); - - word_len = conv * 8; - - if (word_len <= 8) - data_type = DAVINCI_DMA_DATA_TYPE_S8; - else if (word_len <= 16) - data_type = DAVINCI_DMA_DATA_TYPE_S16; - else if (word_len <= 32) - data_type = DAVINCI_DMA_DATA_TYPE_S32; - else - return -EINVAL; - - ret = davinci_spi_bufs_prep(spi, davinci_spi); - if (ret) - return ret; - - /* Put delay val if required */ - iowrite32(0 | (pdata->c2tdelay << SPI_C2TDELAY_SHIFT) | - (pdata->t2cdelay << SPI_T2CDELAY_SHIFT), - davinci_spi->base + SPIDELAY); - - count = davinci_spi->count; /* the number of elements */ - data1_reg_val = pdata->cs_hold << SPIDAT1_CSHOLD_SHIFT; - - /* CS default = 0xFF */ - tmp = ~(0x1 << spi->chip_select); - - clear_io_bits(davinci_spi->base + SPIDEF, ~tmp); - - data1_reg_val |= tmp << SPIDAT1_CSNR_SHIFT; - - /* disable all interrupts for dma transfers */ - clear_io_bits(davinci_spi->base + SPIINT, SPIINT_MASKALL); - /* Disable SPI to write configuration bits in SPIDAT */ - clear_io_bits(davinci_spi->base + SPIGCR1, SPIGCR1_SPIENA_MASK); - iowrite32(data1_reg_val, davinci_spi->base + SPIDAT1); - /* Enable SPI */ + clear_io_bits(davinci_spi->base + SPIGCR1, SPIGCR1_POWERDOWN_MASK); set_io_bits(davinci_spi->base + SPIGCR1, SPIGCR1_SPIENA_MASK); - while ((ioread32(davinci_spi->base + SPIBUF) - & SPIBUF_RXEMPTY_MASK) == 0) - cpu_relax(); - + INIT_COMPLETION(davinci_spi->done); - if (t->tx_buf) { - t->tx_dma = dma_map_single(&spi->dev, (void *)t->tx_buf, count, - DMA_TO_DEVICE); - if (dma_mapping_error(&spi->dev, t->tx_dma)) { - dev_dbg(sdev, "Unable to DMA map a %d bytes" - " TX buffer\n", count); - return -ENOMEM; + if ((spi_cfg->io_type == SPI_IO_TYPE_INTR) || + (spi_cfg->io_type == SPI_IO_TYPE_POLL)) { + + if (spi_cfg->io_type == SPI_IO_TYPE_INTR) + set_io_bits(davinci_spi->base + SPIINT, SPIINT_MASKINT); + + /* start the transfer */ + davinci_spi->wcount--; + tx_data = davinci_spi->get_tx(davinci_spi); + spidat1 &= 0xFFFF0000; + spidat1 |= (tx_data & 0xFFFF); + iowrite32(spidat1, davinci_spi->base + SPIDAT1); + + } else if (spi_cfg->io_type == SPI_IO_TYPE_DMA) { + data_type = spi_cfg->bytes_per_word; + tx_reg = (dma_addr_t)davinci_spi->pbase + SPIDAT1; + rx_reg = (dma_addr_t)davinci_spi->pbase + SPIBUF; + + if (t->tx_buf) { + tx_buf = ((void *)t->tx_buf); + tx_buf_count = davinci_spi->wcount; + } else { + tx_buf = (void *)davinci_spi->tmp_buf; + tx_buf_count = SPI_BUFSIZ; } - temp_count = count; - } else { - /* We need TX clocking for RX transaction */ - t->tx_dma = dma_map_single(&spi->dev, - (void *)davinci_spi->tmp_buf, count + 1, - DMA_TO_DEVICE); - if (dma_mapping_error(&spi->dev, t->tx_dma)) { - dev_dbg(sdev, "Unable to DMA map a %d bytes" - " TX tmp buffer\n", count); - return -ENOMEM; + if (t->rx_buf) { + rx_buf = (void *)t->rx_buf; + rx_buf_count = davinci_spi->rcount; + } else { + rx_buf = (void *)davinci_spi->tmp_buf; + rx_buf_count = SPI_BUFSIZ; } - temp_count = count + 1; + + t->tx_dma = dma_map_single(&spi->dev, tx_buf, + tx_buf_count, DMA_TO_DEVICE); + t->rx_dma = dma_map_single(&spi->dev, rx_buf, + rx_buf_count, DMA_FROM_DEVICE); + + tx_param.opt = TCINTEN | EDMA_TCC(davinci_dma->dma_tx_channel); + tx_param.src = t->tx_buf ? t->tx_dma : tx_reg; + tx_param.a_b_cnt = davinci_spi->wcount << 16 | data_type; + tx_param.dst = tx_reg; + tx_param.src_dst_bidx = t->tx_buf ? data_type : 0; + tx_param.link_bcntrld = 0xffff; + tx_param.src_dst_cidx = 0; + tx_param.ccnt = 1; + edma_write_slot(davinci_dma->dma_tx_channel, &tx_param); + edma_link(davinci_dma->dma_tx_channel, + davinci_dma->dummy_param_slot); + + rx_param.opt = TCINTEN | EDMA_TCC(davinci_dma->dma_rx_channel); + rx_param.src = rx_reg; + rx_param.a_b_cnt = davinci_spi->rcount << 16 | data_type; + rx_param.dst = t->rx_dma; + rx_param.src_dst_bidx = (t->rx_buf ? data_type : 0) << 16; + rx_param.link_bcntrld = 0xffff; + rx_param.src_dst_cidx = 0; + rx_param.ccnt = 1; + edma_write_slot(davinci_dma->dma_rx_channel, &rx_param); + + iowrite16(spidat1 >> SPIDAT1_CSNR_SHIFT, + davinci_spi->base + SPIDAT1 + 2); + + edma_start(davinci_dma->dma_rx_channel); + edma_start(davinci_dma->dma_tx_channel); + set_io_bits(davinci_spi->base + SPIINT, SPIINT_DMA_REQ_EN); } - edma_set_transfer_params(davinci_spi_dma->dma_tx_channel, - data_type, temp_count, 1, 0, ASYNC); - edma_set_dest(davinci_spi_dma->dma_tx_channel, tx_reg, INCR, W8BIT); - edma_set_src(davinci_spi_dma->dma_tx_channel, t->tx_dma, INCR, W8BIT); - edma_set_src_index(davinci_spi_dma->dma_tx_channel, data_type, 0); - edma_set_dest_index(davinci_spi_dma->dma_tx_channel, 0, 0); - - if (t->rx_buf) { - /* initiate transaction */ - iowrite32(data1_reg_val, davinci_spi->base + SPIDAT1); - - t->rx_dma = dma_map_single(&spi->dev, (void *)t->rx_buf, count, - DMA_FROM_DEVICE); - if (dma_mapping_error(&spi->dev, t->rx_dma)) { - dev_dbg(sdev, "Couldn't DMA map a %d bytes RX buffer\n", - count); - if (t->tx_buf != NULL) - dma_unmap_single(NULL, t->tx_dma, - count, DMA_TO_DEVICE); - return -ENOMEM; + /* Wait for the transfer to complete */ + if (spi_cfg->io_type != SPI_IO_TYPE_POLL) { + wait_for_completion_interruptible(&(davinci_spi->done)); + } else { + while ((davinci_spi->rcount > 0) && (ret == 0)) { + ret = davinci_spi_process_events(davinci_spi); + cpu_relax(); } - edma_set_transfer_params(davinci_spi_dma->dma_rx_channel, - data_type, count, 1, 0, ASYNC); - edma_set_src(davinci_spi_dma->dma_rx_channel, - rx_reg, INCR, W8BIT); - edma_set_dest(davinci_spi_dma->dma_rx_channel, - t->rx_dma, INCR, W8BIT); - edma_set_src_index(davinci_spi_dma->dma_rx_channel, 0, 0); - edma_set_dest_index(davinci_spi_dma->dma_rx_channel, - data_type, 0); } - if ((t->tx_buf) || (t->rx_buf)) - edma_start(davinci_spi_dma->dma_tx_channel); - - if (t->rx_buf) - edma_start(davinci_spi_dma->dma_rx_channel); - - if ((t->rx_buf) || (t->tx_buf)) - davinci_spi_set_dma_req(spi, 1); - - if (t->tx_buf) - wait_for_completion_interruptible( - &davinci_spi_dma->dma_tx_completion); - - if (t->rx_buf) - wait_for_completion_interruptible( - &davinci_spi_dma->dma_rx_completion); - - dma_unmap_single(NULL, t->tx_dma, temp_count, DMA_TO_DEVICE); - - if (t->rx_buf) - dma_unmap_single(NULL, t->rx_dma, count, DMA_FROM_DEVICE); - - /* - * Check for bit error, desync error,parity error,timeout error and - * receive overflow errors - */ - int_status = ioread32(davinci_spi->base + SPIFLG); + clear_io_bits(davinci_spi->base + SPIINT, SPIINT_MASKALL); + if (spi_cfg->io_type == SPI_IO_TYPE_DMA) { + dma_unmap_single(NULL, t->tx_dma, tx_buf_count, + DMA_TO_DEVICE); + dma_unmap_single(NULL, t->rx_dma, rx_buf_count, + DMA_FROM_DEVICE); + } - ret = davinci_spi_check_error(davinci_spi, int_status); - if (ret != 0) - return ret; + clear_io_bits(davinci_spi->base + SPIGCR1, SPIGCR1_SPIENA_MASK); + set_io_bits(davinci_spi->base + SPIGCR1, SPIGCR1_POWERDOWN_MASK); - /* SPI Framework maintains the count only in bytes so convert back */ - davinci_spi->count *= conv; + if (davinci_spi->errors) { + ret = davinci_spi_check_error(davinci_spi, davinci_spi->errors); + if (ret != 0) + return ret; + } + if ((davinci_spi->rcount != 0) || (davinci_spi->wcount != 0)) { + sdev = davinci_spi->bitbang.master->dev.parent; + dev_info(sdev, "SPI data transfer error\n"); + return -EIO; + } return t->len; } -/** - * davinci_spi_irq - IRQ handler for DaVinci SPI +/* + * davinci_spi_irq - probe function for SPI Master Controller * @irq: IRQ number for this SPI Master * @context_data: structure for SPI Master controller davinci_spi + * + * ISR will determine that interrupt arrives either for READ or WRITE command. + * According to command it will do the appropriate action. It will check + * transfer length and if it is not zero then dispatch transfer command again. + * If transfer length is zero then it will indicate the COMPLETION so that + * davinci_spi_bufs function can go ahead. */ static irqreturn_t davinci_spi_irq(s32 irq, void *context_data) { struct davinci_spi *davinci_spi = context_data; - u32 int_status, rx_data = 0; - irqreturn_t ret = IRQ_NONE; - - int_status = ioread32(davinci_spi->base + SPIFLG); + int status; - while ((int_status & SPIFLG_RX_INTR_MASK)) { - if (likely(int_status & SPIFLG_RX_INTR_MASK)) { - ret = IRQ_HANDLED; + status = davinci_spi_process_events(davinci_spi); + if (unlikely(status != 0)) + clear_io_bits(davinci_spi->base + SPIINT, SPIINT_MASKINT); - rx_data = ioread32(davinci_spi->base + SPIBUF); - davinci_spi->get_rx(rx_data, davinci_spi); + if ((davinci_spi->rcount == 0) || (status != 0)) + complete(&(davinci_spi->done)); - /* Disable Receive Interrupt */ - iowrite32(~(SPIINT_RX_INTR | SPIINT_TX_INTR), - davinci_spi->base + SPIINT); - } else - (void)davinci_spi_check_error(davinci_spi, int_status); + return IRQ_HANDLED; +} - int_status = ioread32(davinci_spi->base + SPIFLG); +resource_size_t davinci_spi_get_dma_by_flag(struct platform_device *dev, + unsigned long flag) +{ + struct resource *r; + int i; + + for (i = 0; i < dev->num_resources; i++) { + r = platform_get_resource(dev, IORESOURCE_DMA, i); + if (r == NULL) + break; + if ((r->flags & flag) == flag) + return r->start; } - return ret; + return DAVINCI_SPI_NO_RESOURCE; } -/** +/* * davinci_spi_probe - probe function for SPI Master Controller * @pdev: platform_device structure which contains plateform specific data + * + * According to Linux Device Model this function will be invoked by Linux + * with platform_device struct which contains the device specific info. + * This function will map the SPI controller's memory, register IRQ, + * Reset SPI controller and setting its registers to default value. + * It will invoke spi_bitbang_start to create work queue so that client driver + * can register transfer method to work queue. */ static int davinci_spi_probe(struct platform_device *pdev) { @@ -1016,10 +891,11 @@ static int davinci_spi_probe(struct platform_device *pdev) struct davinci_spi *davinci_spi; struct davinci_spi_platform_data *pdata; struct resource *r, *mem; - resource_size_t dma_rx_chan = SPI_NO_RESOURCE; - resource_size_t dma_tx_chan = SPI_NO_RESOURCE; - resource_size_t dma_eventq = SPI_NO_RESOURCE; + resource_size_t dma_rx_chan = DAVINCI_SPI_NO_RESOURCE; + resource_size_t dma_tx_chan = DAVINCI_SPI_NO_RESOURCE; + resource_size_t dma_eventq = DAVINCI_SPI_NO_RESOURCE; int i = 0, ret = 0; + u32 spipc0; pdata = pdev->dev.platform_data; if (pdata == NULL) { @@ -1073,14 +949,16 @@ static int davinci_spi_probe(struct platform_device *pdev) ret = request_irq(davinci_spi->irq, davinci_spi_irq, IRQF_DISABLED, dev_name(&pdev->dev), davinci_spi); - if (ret) + if (ret != 0) { + ret = -EAGAIN; goto unmap_io; + } /* Allocate tmp_buf for tx_buf */ davinci_spi->tmp_buf = kzalloc(SPI_BUFSIZ, GFP_KERNEL); if (davinci_spi->tmp_buf == NULL) { ret = -ENOMEM; - goto irq_free; + goto err1; } davinci_spi->bitbang.master = spi_master_get(master); @@ -1104,55 +982,23 @@ static int davinci_spi_probe(struct platform_device *pdev) davinci_spi->bitbang.chipselect = davinci_spi_chipselect; davinci_spi->bitbang.setup_transfer = davinci_spi_setup_transfer; + davinci_spi->bitbang.txrx_bufs = davinci_spi_txrx_bufs; davinci_spi->version = pdata->version; - use_dma = pdata->use_dma; davinci_spi->bitbang.flags = SPI_NO_CS | SPI_LSB_FIRST | SPI_LOOP; if (davinci_spi->version == SPI_VERSION_2) davinci_spi->bitbang.flags |= SPI_READY; - if (use_dma) { - r = platform_get_resource(pdev, IORESOURCE_DMA, 0); - if (r) - dma_rx_chan = r->start; - r = platform_get_resource(pdev, IORESOURCE_DMA, 1); - if (r) - dma_tx_chan = r->start; - r = platform_get_resource(pdev, IORESOURCE_DMA, 2); - if (r) - dma_eventq = r->start; - } - - if (!use_dma || - dma_rx_chan == SPI_NO_RESOURCE || - dma_tx_chan == SPI_NO_RESOURCE || - dma_eventq == SPI_NO_RESOURCE) { - davinci_spi->bitbang.txrx_bufs = davinci_spi_bufs_pio; - use_dma = 0; - } else { - davinci_spi->bitbang.txrx_bufs = davinci_spi_bufs_dma; - davinci_spi->dma_channels = kzalloc(master->num_chipselect - * sizeof(struct davinci_spi_dma), GFP_KERNEL); - if (davinci_spi->dma_channels == NULL) { - ret = -ENOMEM; - goto free_clk; - } - - for (i = 0; i < master->num_chipselect; i++) { - davinci_spi->dma_channels[i].dma_rx_channel = -1; - davinci_spi->dma_channels[i].dma_rx_sync_dev = - dma_rx_chan; - davinci_spi->dma_channels[i].dma_tx_channel = -1; - davinci_spi->dma_channels[i].dma_tx_sync_dev = - dma_tx_chan; - davinci_spi->dma_channels[i].eventq = dma_eventq; - } - dev_info(&pdev->dev, "DaVinci SPI driver in EDMA mode\n" - "Using RX channel = %d , TX channel = %d and " - "event queue = %d", dma_rx_chan, dma_tx_chan, - dma_eventq); - } + dma_rx_chan = davinci_spi_get_dma_by_flag(pdev, IORESOURCE_DMA_RX_CHAN); + dma_tx_chan = davinci_spi_get_dma_by_flag(pdev, IORESOURCE_DMA_TX_CHAN); + dma_eventq = davinci_spi_get_dma_by_flag(pdev, IORESOURCE_DMA_EVENT_Q); + davinci_spi->dma_channels.dma_rx_channel = -1; + davinci_spi->dma_channels.dma_rx_sync_dev = dma_rx_chan; + davinci_spi->dma_channels.dma_tx_channel = -1; + davinci_spi->dma_channels.dma_tx_sync_dev = dma_tx_chan; + davinci_spi->dma_channels.dummy_param_slot = -1; + davinci_spi->dma_channels.eventq = dma_eventq; davinci_spi->get_rx = davinci_spi_rx_buf_u8; davinci_spi->get_tx = davinci_spi_tx_buf_u8; @@ -1164,32 +1010,29 @@ static int davinci_spi_probe(struct platform_device *pdev) udelay(100); iowrite32(1, davinci_spi->base + SPIGCR0); - /* Clock internal */ - if (davinci_spi->pdata->clk_internal) - set_io_bits(davinci_spi->base + SPIGCR1, - SPIGCR1_CLKMOD_MASK); - else - clear_io_bits(davinci_spi->base + SPIGCR1, - SPIGCR1_CLKMOD_MASK); + /* Set up SPIPC0. CS and ENA init is done in davinci_spi_setup */ + spipc0 = SPIPC0_DIFUN_MASK | SPIPC0_DOFUN_MASK | SPIPC0_CLKFUN_MASK; + iowrite32(spipc0, davinci_spi->base + SPIPC0); - /* master mode default */ - set_io_bits(davinci_spi->base + SPIGCR1, SPIGCR1_MASTER_MASK); + /* initialize chip selects */ + if (pdata->chip_sel != NULL) { + for (i = 0; i < pdata->num_chipselect; i++) { + if (pdata->chip_sel[i] != SPI_INTERN_CS) + gpio_direction_output(pdata->chip_sel[i], 1); + } + } + iowrite32(SPIDEF_CSDEF_MASK, davinci_spi->base + SPIDEF); - if (davinci_spi->pdata->intr_level) - iowrite32(SPI_INTLVL_1, davinci_spi->base + SPILVL); - else - iowrite32(SPI_INTLVL_0, davinci_spi->base + SPILVL); + set_io_bits(davinci_spi->base + SPIGCR1, SPIGCR1_CLKMOD_MASK); + set_io_bits(davinci_spi->base + SPIGCR1, SPIGCR1_MASTER_MASK); + set_io_bits(davinci_spi->base + SPIGCR1, SPIGCR1_POWERDOWN_MASK); ret = spi_bitbang_start(&davinci_spi->bitbang); - if (ret) + if (ret != 0) goto free_clk; dev_info(&pdev->dev, "Controller at 0x%p \n", davinci_spi->base); - if (!pdata->poll_mode) - dev_info(&pdev->dev, "Operating in interrupt mode" - " using IRQ %d\n", davinci_spi->irq); - return ret; free_clk: @@ -1199,7 +1042,7 @@ put_master: spi_master_put(master); free_tmp_buf: kfree(davinci_spi->tmp_buf); -irq_free: +err1: free_irq(davinci_spi->irq, davinci_spi); unmap_io: iounmap(davinci_spi->base); @@ -1211,7 +1054,7 @@ err: return ret; } -/** +/* * davinci_spi_remove - remove function for SPI Master Controller * @pdev: platform_device structure which contains plateform specific data * @@ -1220,7 +1063,7 @@ err: * It will also call spi_bitbang_stop to destroy the work queue which was * created by spi_bitbang_start. */ -static int __exit davinci_spi_remove(struct platform_device *pdev) +static int __devexit davinci_spi_remove(struct platform_device *pdev) { struct davinci_spi *davinci_spi; struct spi_master *master; @@ -1242,8 +1085,11 @@ static int __exit davinci_spi_remove(struct platform_device *pdev) } static struct platform_driver davinci_spi_driver = { - .driver.name = "spi_davinci", - .remove = __exit_p(davinci_spi_remove), + .driver = { + .name = "spi_davinci", + .owner = THIS_MODULE, + }, + .remove = __devexit_p(davinci_spi_remove), }; static int __init davinci_spi_init(void) -- 1.6.3.3 ------------------------------------------------------------------------------ This SF.net email is sponsored by Sprint What will you do first with EVO, the first 4G phone? Visit sprint.com/first -- http://p.sf.net/sfu/sprint-com-first ^ permalink raw reply related [flat|nested] 12+ messages in thread
[parent not found: <1278110334-13943-2-git-send-email-bniebuhr-JaPwekKOx1yaMJb+Lgu22Q@public.gmane.org>]
* Re: [PATCH v2 1/1] davinci: spi: replace existing driver [not found] ` <1278110334-13943-2-git-send-email-bniebuhr-JaPwekKOx1yaMJb+Lgu22Q@public.gmane.org> @ 2010-07-04 5:47 ` Grant Likely 0 siblings, 0 replies; 12+ messages in thread From: Grant Likely @ 2010-07-04 5:47 UTC (permalink / raw) To: Brian Niebuhr Cc: spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f, davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/ On Fri, Jul 2, 2010 at 4:38 PM, Brian Niebuhr <bniebuhr3-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> wrote: > INTRODUCTION > > I have been working on a custom OMAP-L138 board that has multiple spi > devices (seven) on one controller. These devices have a wide range of > transfer parameters (speed, phase, polarity, internal and gpio chip > selects). During my testing I found multiple errors in the davinci spi > driver as a result of this complex setup. The primary issues were: > > 1. There is a race condition due to the SPIBUF read busy-waits for slow > devices > 2. I found some DMA transfer length errors under some conditions > 3. The chip select code caused extra byte transfers (with no chip > select active) due to writes to SPIDAT1 > 4. Several issues prevented using multiple SPI devices, especially > the DMA code, as disucussed previously on the davinci list. > > The fixes to these problems were not simple. I ended up making fairly > large changes to the driver, and those changes are contained in these > patches. The full list of changes follows. [...] > Signed-off-by: Brian Niebuhr <bniebuhr-JaPwekKOx1yaMJb+Lgu22Q@public.gmane.org> Hi Brian, Thanks for the quick respin. Some more comments below... > --- > arch/arm/mach-davinci/board-dm355-evm.c | 10 + > arch/arm/mach-davinci/board-dm355-leopard.c | 10 + > arch/arm/mach-davinci/board-dm365-evm.c | 10 + > arch/arm/mach-davinci/dm355.c | 12 +- > arch/arm/mach-davinci/dm365.c | 12 +- > arch/arm/mach-davinci/include/mach/spi.h | 37 +- > drivers/spi/davinci_spi.c | 1328 ++++++++++++--------------- > 7 files changed, 648 insertions(+), 771 deletions(-) > > diff --git a/arch/arm/mach-davinci/board-dm355-evm.c b/arch/arm/mach-davinci/board-dm355-evm.c > index a319101..d2e9f20 100644 > --- a/arch/arm/mach-davinci/board-dm355-evm.c > +++ b/arch/arm/mach-davinci/board-dm355-evm.c > @@ -32,6 +32,7 @@ > #include <mach/nand.h> > #include <mach/mmc.h> > #include <mach/usb.h> > +#include <mach/spi.h> > > /* NOTE: this is geared for the standard config, with a socketed > * 2 GByte Micron NAND (MT29F16G08FAA) using 128KB sectors. If you > @@ -300,10 +301,19 @@ static struct spi_eeprom at25640a = { > .flags = EE_ADDR2, > }; > > +static struct davinci_spi_config at25640a_spi_cfg = { > + .parity_enable = false, > + .intr_level = 0, > + .io_type = SPI_IO_TYPE_DMA, > + .wdelay = 0, > + .timer_disable = true, > +}; > + > static struct spi_board_info dm355_evm_spi_info[] __initconst = { > { > .modalias = "at25", > .platform_data = &at25640a, > + .controller_data = &at25640a_spi_cfg, > .max_speed_hz = 10 * 1000 * 1000, /* at 3v3 */ > .bus_num = 0, > .chip_select = 0, > diff --git a/arch/arm/mach-davinci/board-dm355-leopard.c b/arch/arm/mach-davinci/board-dm355-leopard.c > index f1d8132..63078dc 100644 > --- a/arch/arm/mach-davinci/board-dm355-leopard.c > +++ b/arch/arm/mach-davinci/board-dm355-leopard.c > @@ -29,6 +29,7 @@ > #include <mach/nand.h> > #include <mach/mmc.h> > #include <mach/usb.h> > +#include <mach/spi.h> > > /* NOTE: this is geared for the standard config, with a socketed > * 2 GByte Micron NAND (MT29F16G08FAA) using 128KB sectors. If you > @@ -222,10 +223,19 @@ static struct spi_eeprom at25640a = { > .flags = EE_ADDR2, > }; > > +static struct davinci_spi_config at25640a_spi_cfg = { > + .parity_enable = false, > + .intr_level = 0, > + .io_type = SPI_IO_TYPE_DMA, > + .wdelay = 0, > + .timer_disable = true, > +}; > + > static struct spi_board_info dm355_leopard_spi_info[] __initconst = { > { > .modalias = "at25", > .platform_data = &at25640a, > + .controller_data = &at25640a_spi_cfg, > .max_speed_hz = 10 * 1000 * 1000, /* at 3v3 */ > .bus_num = 0, > .chip_select = 0, > diff --git a/arch/arm/mach-davinci/board-dm365-evm.c b/arch/arm/mach-davinci/board-dm365-evm.c > index 5bb86b2..5bc3622 100644 > --- a/arch/arm/mach-davinci/board-dm365-evm.c > +++ b/arch/arm/mach-davinci/board-dm365-evm.c > @@ -39,6 +39,7 @@ > #include <mach/mmc.h> > #include <mach/nand.h> > #include <mach/keyscan.h> > +#include <mach/spi.h> > > #include <media/tvp514x.h> > > @@ -579,10 +580,19 @@ static struct spi_eeprom at25640 = { > .flags = EE_ADDR2, > }; > > +static struct davinci_spi_config at25640_spi_cfg = { > + .parity_enable = false, > + .intr_level = 0, > + .io_type = SPI_IO_TYPE_DMA, > + .wdelay = 0, > + .timer_disable = true, > +}; > + > static struct spi_board_info dm365_evm_spi_info[] __initconst = { > { > .modalias = "at25", > .platform_data = &at25640, > + .controller_data = &at25640_spi_cfg, > .max_speed_hz = 10 * 1000 * 1000, > .bus_num = 0, > .chip_select = 0, > diff --git a/arch/arm/mach-davinci/dm355.c b/arch/arm/mach-davinci/dm355.c > index 3834781..378d41c 100644 > --- a/arch/arm/mach-davinci/dm355.c > +++ b/arch/arm/mach-davinci/dm355.c > @@ -397,27 +397,21 @@ static struct resource dm355_spi0_resources[] = { > }, > { > .start = 17, > - .flags = IORESOURCE_DMA, > + .flags = IORESOURCE_DMA | IORESOURCE_DMA_RX_CHAN, > }, > { > .start = 16, > - .flags = IORESOURCE_DMA, > + .flags = IORESOURCE_DMA | IORESOURCE_DMA_TX_CHAN, > }, > { > .start = EVENTQ_1, > - .flags = IORESOURCE_DMA, > + .flags = IORESOURCE_DMA | IORESOURCE_DMA_EVENT_Q, > }, > }; > > static struct davinci_spi_platform_data dm355_spi0_pdata = { > .version = SPI_VERSION_1, > .num_chipselect = 2, > - .clk_internal = 1, > - .cs_hold = 1, > - .intr_level = 0, > - .poll_mode = 1, /* 0 -> interrupt mode 1-> polling mode */ > - .c2tdelay = 0, > - .t2cdelay = 0, > }; > static struct platform_device dm355_spi0_device = { > .name = "spi_davinci", > diff --git a/arch/arm/mach-davinci/dm365.c b/arch/arm/mach-davinci/dm365.c > index 652f4b6..8e68f8c 100644 > --- a/arch/arm/mach-davinci/dm365.c > +++ b/arch/arm/mach-davinci/dm365.c > @@ -625,12 +625,6 @@ static u64 dm365_spi0_dma_mask = DMA_BIT_MASK(32); > static struct davinci_spi_platform_data dm365_spi0_pdata = { > .version = SPI_VERSION_1, > .num_chipselect = 2, > - .clk_internal = 1, > - .cs_hold = 1, > - .intr_level = 0, > - .poll_mode = 1, /* 0 -> interrupt mode 1-> polling mode */ > - .c2tdelay = 0, > - .t2cdelay = 0, > }; > > static struct resource dm365_spi0_resources[] = { > @@ -645,15 +639,15 @@ static struct resource dm365_spi0_resources[] = { > }, > { > .start = 17, > - .flags = IORESOURCE_DMA, > + .flags = IORESOURCE_DMA | IORESOURCE_DMA_RX_CHAN, > }, > { > .start = 16, > - .flags = IORESOURCE_DMA, > + .flags = IORESOURCE_DMA | IORESOURCE_DMA_TX_CHAN, > }, > { > .start = EVENTQ_3, > - .flags = IORESOURCE_DMA, > + .flags = IORESOURCE_DMA | IORESOURCE_DMA_EVENT_Q, > }, > }; > > diff --git a/arch/arm/mach-davinci/include/mach/spi.h b/arch/arm/mach-davinci/include/mach/spi.h > index 910efbf..b69a2f5 100644 > --- a/arch/arm/mach-davinci/include/mach/spi.h > +++ b/arch/arm/mach-davinci/include/mach/spi.h > @@ -19,6 +19,13 @@ > #ifndef __ARCH_ARM_DAVINCI_SPI_H > #define __ARCH_ARM_DAVINCI_SPI_H > > +#define SPI_INTERN_CS 0xFF > + > +/* resource flags for IORESOURCE_DMA resources */ > +#define IORESOURCE_DMA_RX_CHAN 0x01 > +#define IORESOURCE_DMA_TX_CHAN 0x02 > +#define IORESOURCE_DMA_EVENT_Q 0x04 > + Not a good idea. IORESOURCE_* definitions are defined in ioport.h and the lower 8 bits are tagged for bus-specific use (not device-specific). Overloading them with arch-specific meanings is just asking for breakage. If index is unreliable, you can differentiate the resources by .name. > enum { > SPI_VERSION_1, /* For DM355/DM365/DM6467 */ > SPI_VERSION_2, /* For DA8xx */ > @@ -26,19 +33,25 @@ enum { > > struct davinci_spi_platform_data { > u8 version; > - u8 num_chipselect; > - u8 wdelay; > - u8 odd_parity; > - u8 parity_enable; > - u8 wait_enable; > - u8 timer_disable; > - u8 clk_internal; > - u8 cs_hold; > + u16 num_chipselect; > + u8 *chip_sel; > +}; > + > +struct davinci_spi_config { > + bool odd_parity; > + bool parity_enable; > u8 intr_level; > - u8 poll_mode; > - u8 use_dma; > - u8 c2tdelay; > - u8 t2cdelay; > + u8 io_type; > +#define SPI_IO_TYPE_INTR 0 > +#define SPI_IO_TYPE_POLL 1 > +#define SPI_IO_TYPE_DMA 2 > + u8 bytes_per_word; > + u8 wdelay; > + bool timer_disable; > + u8 c2t_delay; > + u8 t2c_delay; > + u8 t2e_delay; > + u8 c2e_delay; > }; > > #endif /* __ARCH_ARM_DAVINCI_SPI_H */ > diff --git a/drivers/spi/davinci_spi.c b/drivers/spi/davinci_spi.c > index b85090c..10d5c34 100644 > --- a/drivers/spi/davinci_spi.c > +++ b/drivers/spi/davinci_spi.c > @@ -1,5 +1,6 @@ > /* > * Copyright (C) 2009 Texas Instruments. > + * Copyright (C) 2010 EF Johnson Technologies > * > * This program is free software; you can redistribute it and/or modify > * it under the terms of the GNU General Public License as published by > @@ -27,197 +28,218 @@ > #include <linux/dma-mapping.h> > #include <linux/spi/spi.h> > #include <linux/spi/spi_bitbang.h> > -#include <linux/slab.h> > > #include <mach/spi.h> > #include <mach/edma.h> > > -#define SPI_NO_RESOURCE ((resource_size_t)-1) > - > -#define SPI_MAX_CHIPSELECT 2 > - > -#define CS_DEFAULT 0xFF > - > -#define SPI_BUFSIZ (SMP_CACHE_BYTES + 1) > -#define DAVINCI_DMA_DATA_TYPE_S8 0x01 > -#define DAVINCI_DMA_DATA_TYPE_S16 0x02 > -#define DAVINCI_DMA_DATA_TYPE_S32 0x04 > - > -#define SPIFMT_PHASE_MASK BIT(16) > -#define SPIFMT_POLARITY_MASK BIT(17) > -#define SPIFMT_DISTIMER_MASK BIT(18) > -#define SPIFMT_SHIFTDIR_MASK BIT(20) > -#define SPIFMT_WAITENA_MASK BIT(21) > -#define SPIFMT_PARITYENA_MASK BIT(22) > -#define SPIFMT_ODD_PARITY_MASK BIT(23) > -#define SPIFMT_WDELAY_MASK 0x3f000000u > -#define SPIFMT_WDELAY_SHIFT 24 > -#define SPIFMT_CHARLEN_MASK 0x0000001Fu > +#define CS_DEFAULT 0xFF > +#define SCS0_SELECT 0x01 > +#define SCS1_SELECT 0x02 > +#define SCS2_SELECT 0x04 > +#define SCS3_SELECT 0x08 > +#define SCS4_SELECT 0x10 > +#define SCS5_SELECT 0x20 > +#define SCS6_SELECT 0x40 > +#define SCS7_SELECT 0x80 > + > +#define SPIFMT_PHASE_MASK BIT(16) > +#define SPIFMT_POLARITY_MASK BIT(17) > +#define SPIFMT_DISTIMER_MASK BIT(18) > +#define SPIFMT_SHIFTDIR_MASK BIT(20) > +#define SPIFMT_WAITENA_MASK BIT(21) > +#define SPIFMT_PARITYENA_MASK BIT(22) > +#define SPIFMT_ODD_PARITY_MASK BIT(23) > +#define SPIFMT_WDELAY_MASK 0x3f000000u > +#define SPIFMT_WDELAY_SHIFT 24 > +#define SPIFMT_CHARLEN_MASK 0x0000001Fu > +#define SPIFMT_PRESCALE_SHIFT 8 > > /* SPIGCR1 */ > -#define SPIGCR1_SPIENA_MASK 0x01000000u > +#define SPIGCR1_SPIENA_MASK BIT(24) > +#define SPIGCR1_POWERDOWN_MASK BIT(8) > > /* SPIPC0 */ > -#define SPIPC0_DIFUN_MASK BIT(11) /* MISO */ > -#define SPIPC0_DOFUN_MASK BIT(10) /* MOSI */ > -#define SPIPC0_CLKFUN_MASK BIT(9) /* CLK */ > -#define SPIPC0_SPIENA_MASK BIT(8) /* nREADY */ > -#define SPIPC0_EN1FUN_MASK BIT(1) > -#define SPIPC0_EN0FUN_MASK BIT(0) > - > -#define SPIINT_MASKALL 0x0101035F > -#define SPI_INTLVL_1 0x000001FFu > -#define SPI_INTLVL_0 0x00000000u > +#define SPIPC0_DIFUN_MASK BIT(11) /* MISO */ > +#define SPIPC0_DOFUN_MASK BIT(10) /* MOSI */ > +#define SPIPC0_CLKFUN_MASK BIT(9) /* CLK */ > +#define SPIPC0_SPIENA_MASK BIT(8) /* nREADY */ > +#define SPIPC0_EN1FUN_MASK BIT(1) > +#define SPIPC0_EN0FUN_MASK BIT(0) > + > +#define SPIINT_MASKALL 0x0101035Fu > +#define SPIINT_MASKINT 0x0000035Fu > +#define SPI_INTLVL_1 0x000001FFu > +#define SPI_INTLVL_0 0x00000000u > > /* SPIDAT1 */ > +#define SPIDAT1_CSHOLD_MASK BIT(28) > #define SPIDAT1_CSHOLD_SHIFT 28 > +#define SPIDAT1_WDEL_MASK BIT(26) > +#define SPIDAT1_CSNR_MASK 0x00FF0000u > #define SPIDAT1_CSNR_SHIFT 16 > +#define SPIDAT1_DFSEL_MASK (BIT(24 | BIT(25)) > #define SPIGCR1_CLKMOD_MASK BIT(1) > -#define SPIGCR1_MASTER_MASK BIT(0) > +#define SPIGCR1_MASTER_MASK BIT(0) > #define SPIGCR1_LOOPBACK_MASK BIT(16) > > /* SPIBUF */ > -#define SPIBUF_TXFULL_MASK BIT(29) > -#define SPIBUF_RXEMPTY_MASK BIT(31) > +#define SPIBUF_TXFULL_MASK BIT(29) > +#define SPIBUF_RXEMPTY_MASK BIT(31) > + > +/* SPIDELAY */ > +#define SPIDELAY_C2TDELAY_MASK 0xFF000000u > +#define SPIDELAY_C2TDELAY_SHIFT 24 > +#define SPIDELAY_T2CDELAY_MASK 0x00FF0000u > +#define SPIDELAY_T2CDELAY_SHIFT 16 > +#define SPIDELAY_T2EDELAY_MASK 0x0000FF00u > +#define SPIDELAY_T2EDELAY_SHIFT 8 > +#define SPIDELAY_C2EDELAY_MASK 0x000000FFu > +#define SPIDELAY_C2EDELAY_SHIFT 0 > + > +/* SPIDEF */ > +#define SPIDEF_CSDEF_MASK 0x000000FFu > > /* Error Masks */ > -#define SPIFLG_DLEN_ERR_MASK BIT(0) > -#define SPIFLG_TIMEOUT_MASK BIT(1) > -#define SPIFLG_PARERR_MASK BIT(2) > -#define SPIFLG_DESYNC_MASK BIT(3) > -#define SPIFLG_BITERR_MASK BIT(4) > -#define SPIFLG_OVRRUN_MASK BIT(6) > -#define SPIFLG_RX_INTR_MASK BIT(8) > -#define SPIFLG_TX_INTR_MASK BIT(9) > -#define SPIFLG_BUF_INIT_ACTIVE_MASK BIT(24) > -#define SPIFLG_MASK (SPIFLG_DLEN_ERR_MASK \ > - | SPIFLG_TIMEOUT_MASK | SPIFLG_PARERR_MASK \ > - | SPIFLG_DESYNC_MASK | SPIFLG_BITERR_MASK \ > - | SPIFLG_OVRRUN_MASK | SPIFLG_RX_INTR_MASK \ > - | SPIFLG_TX_INTR_MASK \ > - | SPIFLG_BUF_INIT_ACTIVE_MASK) > - > -#define SPIINT_DLEN_ERR_INTR BIT(0) > -#define SPIINT_TIMEOUT_INTR BIT(1) > -#define SPIINT_PARERR_INTR BIT(2) > -#define SPIINT_DESYNC_INTR BIT(3) > -#define SPIINT_BITERR_INTR BIT(4) > -#define SPIINT_OVRRUN_INTR BIT(6) > -#define SPIINT_RX_INTR BIT(8) > -#define SPIINT_TX_INTR BIT(9) > -#define SPIINT_DMA_REQ_EN BIT(16) > -#define SPIINT_ENABLE_HIGHZ BIT(24) > - > -#define SPI_T2CDELAY_SHIFT 16 > -#define SPI_C2TDELAY_SHIFT 24 > - > +#define SPIFLG_DLEN_ERR_MASK BIT(0) > +#define SPIFLG_TIMEOUT_MASK BIT(1) > +#define SPIFLG_PARERR_MASK BIT(2) > +#define SPIFLG_DESYNC_MASK BIT(3) > +#define SPIFLG_BITERR_MASK BIT(4) > +#define SPIFLG_OVRRUN_MASK BIT(6) > +#define SPIFLG_RX_INTR_MASK BIT(8) > +#define SPIFLG_TX_INTR_MASK BIT(9) > +#define SPIFLG_BUF_INIT_ACTIVE_MASK BIT(24) > +#define SPIFLG_ERROR_MASK (SPIFLG_DLEN_ERR_MASK \ > + | SPIFLG_TIMEOUT_MASK | SPIFLG_PARERR_MASK \ > + | SPIFLG_DESYNC_MASK | SPIFLG_BITERR_MASK \ > + | SPIFLG_OVRRUN_MASK) > +#define SPIFLG_MASK (SPIFLG_ERROR_MASK \ > + | SPIFLG_RX_INTR_MASK | SPIFLG_TX_INTR_MASK \ > + | SPIFLG_BUF_INIT_ACTIVE_MASK) > + > +#define SPIINT_DLEN_ERR_INTR BIT(0) > +#define SPIINT_TIMEOUT_INTR BIT(1) > +#define SPIINT_PARERR_INTR BIT(2) > +#define SPIINT_DESYNC_INTR BIT(3) > +#define SPIINT_BITERR_INTR BIT(4) > +#define SPIINT_OVRRUN_INTR BIT(6) > +#define SPIINT_RX_INTR BIT(8) > +#define SPIINT_TX_INTR BIT(9) > +#define SPIINT_DMA_REQ_EN BIT(16) > +#define SPIINT_ENABLE_HIGHZ BIT(24) > + > +#define SPI_T2CDELAY_SHIFT 16 > +#define SPI_C2TDELAY_SHIFT 24 > /* SPI Controller registers */ > -#define SPIGCR0 0x00 > -#define SPIGCR1 0x04 > -#define SPIINT 0x08 > -#define SPILVL 0x0c > -#define SPIFLG 0x10 > -#define SPIPC0 0x14 > -#define SPIPC1 0x18 > -#define SPIPC2 0x1c > -#define SPIPC3 0x20 > -#define SPIPC4 0x24 > -#define SPIPC5 0x28 > -#define SPIPC6 0x2c > -#define SPIPC7 0x30 > -#define SPIPC8 0x34 > -#define SPIDAT0 0x38 > -#define SPIDAT1 0x3c > -#define SPIBUF 0x40 > -#define SPIEMU 0x44 > -#define SPIDELAY 0x48 > -#define SPIDEF 0x4c > -#define SPIFMT0 0x50 > -#define SPIFMT1 0x54 > -#define SPIFMT2 0x58 > -#define SPIFMT3 0x5c > -#define TGINTVEC0 0x60 > -#define TGINTVEC1 0x64 > - > -struct davinci_spi_slave { > - u32 cmd_to_write; > - u32 clk_ctrl_to_write; > - u32 bytes_per_word; > - u8 active_cs; > +#define SPIGCR0 0x00 > +#define SPIGCR1 0x04 > +#define SPIINT 0x08 > +#define SPILVL 0x0c > +#define SPIFLG 0x10 > +#define SPIPC0 0x14 > +#define SPIPC1 0x18 > +#define SPIPC2 0x1c > +#define SPIPC3 0x20 > +#define SPIPC4 0x24 > +#define SPIPC5 0x28 > +#define SPIPC6 0x2c > +#define SPIPC7 0x30 > +#define SPIPC8 0x34 > +#define SPIDAT0 0x38 > +#define SPIDAT1 0x3c > +#define SPIBUF 0x40 > +#define SPIEMU 0x44 > +#define SPIDELAY 0x48 > +#define SPIDEF 0x4c > +#define SPIFMT0 0x50 > +#define SPIFMT1 0x54 > +#define SPIFMT2 0x58 > +#define SPIFMT3 0x5c > +#define TGINTVEC0 0x60 > +#define TGINTVEC1 0x64 > + > +#define SPI_BUFSIZ (SMP_CACHE_BYTES + 1) > + > +const char * const io_type_names[] = { > + [SPI_IO_TYPE_INTR] = "Interrupt", > + [SPI_IO_TYPE_POLL] = "Polled", > + [SPI_IO_TYPE_DMA] = "DMA", > }; > > /* We have 2 DMA channels per CS, one for RX and one for TX */ > struct davinci_spi_dma { > - int dma_tx_channel; > - int dma_rx_channel; > - int dma_tx_sync_dev; > - int dma_rx_sync_dev; > - enum dma_event_q eventq; > - > - struct completion dma_tx_completion; > - struct completion dma_rx_completion; > + int dma_tx_channel; > + int dma_rx_channel; > + int dma_tx_sync_dev; > + int dma_rx_sync_dev; > + int dummy_param_slot; > + enum dma_event_q eventq; > }; > > /* SPI Controller driver's private data. */ > struct davinci_spi { > - struct spi_bitbang bitbang; > - struct clk *clk; > - > - u8 version; > - resource_size_t pbase; > - void __iomem *base; > - size_t region_size; > - u32 irq; > - struct completion done; > - > - const void *tx; > - void *rx; > - u8 *tmp_buf; > - int count; > - struct davinci_spi_dma *dma_channels; > - struct davinci_spi_platform_data *pdata; > - > - void (*get_rx)(u32 rx_data, struct davinci_spi *); > - u32 (*get_tx)(struct davinci_spi *); > - > - struct davinci_spi_slave slave[SPI_MAX_CHIPSELECT]; > + struct spi_bitbang bitbang; > + struct clk *clk; > + > + u8 version; > + resource_size_t pbase; > + void __iomem *base; > + size_t region_size; > + u32 irq; > + struct completion done; > + > + const void *tx; > + void *rx; > + u8 *tmp_buf; > + int rcount; > + int wcount; > + u32 errors; > + struct davinci_spi_dma dma_channels; > + struct davinci_spi_platform_data *pdata; > + > + void (*get_rx)(u32 rx_data, struct davinci_spi *); > + u32 (*get_tx)(struct davinci_spi *); > }; > > -static unsigned use_dma; > +#define DAVINCI_SPI_NO_RESOURCE ((resource_size_t)-1) > > static void davinci_spi_rx_buf_u8(u32 data, struct davinci_spi *davinci_spi) > { > - u8 *rx = davinci_spi->rx; > - > - *rx++ = (u8)data; > - davinci_spi->rx = rx; > + if (davinci_spi->rx) { > + u8 *rx = davinci_spi->rx; > + *rx++ = (u8)data; > + davinci_spi->rx = rx; > + } > } > > static void davinci_spi_rx_buf_u16(u32 data, struct davinci_spi *davinci_spi) > { > - u16 *rx = davinci_spi->rx; > - > - *rx++ = (u16)data; > - davinci_spi->rx = rx; > + if (davinci_spi->rx) { > + u16 *rx = davinci_spi->rx; > + *rx++ = (u16)data; > + davinci_spi->rx = rx; > + } > } > > static u32 davinci_spi_tx_buf_u8(struct davinci_spi *davinci_spi) > { > - u32 data; > - const u8 *tx = davinci_spi->tx; > - > - data = *tx++; > - davinci_spi->tx = tx; > + u32 data = 0; > + if (davinci_spi->tx) { > + const u8 *tx = davinci_spi->tx; > + data = *tx++; > + davinci_spi->tx = tx; > + } > return data; > } > > static u32 davinci_spi_tx_buf_u16(struct davinci_spi *davinci_spi) > { > - u32 data; > - const u16 *tx = davinci_spi->tx; > - > - data = *tx++; > - davinci_spi->tx = tx; > + u32 data = 0; > + if (davinci_spi->tx) { > + const u16 *tx = davinci_spi->tx; > + data = *tx++; > + davinci_spi->tx = tx; > + } > return data; > } > > @@ -237,26 +259,6 @@ static inline void clear_io_bits(void __iomem *addr, u32 bits) > iowrite32(v, addr); > } > > -static inline void set_fmt_bits(void __iomem *addr, u32 bits, int cs_num) > -{ > - set_io_bits(addr + SPIFMT0 + (0x4 * cs_num), bits); > -} > - > -static inline void clear_fmt_bits(void __iomem *addr, u32 bits, int cs_num) > -{ > - clear_io_bits(addr + SPIFMT0 + (0x4 * cs_num), bits); > -} > - > -static void davinci_spi_set_dma_req(const struct spi_device *spi, int enable) > -{ > - struct davinci_spi *davinci_spi = spi_master_get_devdata(spi->master); > - > - if (enable) > - set_io_bits(davinci_spi->base + SPIINT, SPIINT_DMA_REQ_EN); > - else > - clear_io_bits(davinci_spi->base + SPIINT, SPIINT_DMA_REQ_EN); > -} > - > /* > * Interface to control the chip select signal > */ > @@ -264,28 +266,57 @@ static void davinci_spi_chipselect(struct spi_device *spi, int value) > { > struct davinci_spi *davinci_spi; > struct davinci_spi_platform_data *pdata; > - u32 data1_reg_val = 0; > + u8 i, chip_sel = spi->chip_select; > + u32 spidat1; > + u16 spidat1_cfg; > > davinci_spi = spi_master_get_devdata(spi->master); > pdata = davinci_spi->pdata; > > - /* > - * Board specific chip select logic decides the polarity and cs > - * line for the controller > - */ > - if (value == BITBANG_CS_INACTIVE) { > - set_io_bits(davinci_spi->base + SPIDEF, CS_DEFAULT); > - > - data1_reg_val |= CS_DEFAULT << SPIDAT1_CSNR_SHIFT; > - iowrite32(data1_reg_val, davinci_spi->base + SPIDAT1); > + spidat1 = SPIDAT1_CSNR_MASK; > + if (value == BITBANG_CS_ACTIVE) > + spidat1 |= SPIDAT1_CSHOLD_MASK; > + else > + spidat1 |= SPIDAT1_WDEL_MASK; > > - while ((ioread32(davinci_spi->base + SPIBUF) > - & SPIBUF_RXEMPTY_MASK) == 0) > - cpu_relax(); > + if (pdata->chip_sel == NULL) { > + if (value == BITBANG_CS_ACTIVE) > + spidat1 &= ~((0x1 << chip_sel) << SPIDAT1_CSNR_SHIFT); > + } else { > + for (i = 0; i < pdata->num_chipselect; i++) { > + if (pdata->chip_sel[i] == SPI_INTERN_CS) { > + if ((i == chip_sel) && > + (value == BITBANG_CS_ACTIVE)) { > + spidat1 &= ~((0x1 << chip_sel) > + << SPIDAT1_CSNR_SHIFT); > + } > + } else { > + if (value == BITBANG_CS_INACTIVE) > + gpio_set_value(pdata->chip_sel[i], 1); > + else if (i == chip_sel) > + gpio_set_value(pdata->chip_sel[i], 0); > + } > + } > } > + > + spidat1_cfg = spidat1 >> SPIDAT1_CSNR_SHIFT; > + iowrite16(spidat1_cfg, davinci_spi->base + SPIDAT1 + 2); > +} > + > +/* > + * davinci_spi_get_prescale - Calculates the correct prescale value > + * @max_speed_hz: the maximum rate the SPI clock can run at > + * > + * This function calculates the prescale value that generates a clock rate > + * less than or equal to the specified maximum > + */ > +static inline u32 davinci_spi_get_prescale(struct davinci_spi *davinci_spi, > + u32 max_speed_hz) > +{ > + return ((clk_get_rate(davinci_spi->clk) - 1) / max_speed_hz) & 0xff; > } > > -/** > +/* > * davinci_spi_setup_transfer - This functions will determine transfer method > * @spi: spi device on which data transfer to be done > * @t: spi transfer in which transfer info is filled > @@ -297,14 +328,15 @@ static void davinci_spi_chipselect(struct spi_device *spi, int value) > static int davinci_spi_setup_transfer(struct spi_device *spi, > struct spi_transfer *t) > { > - > struct davinci_spi *davinci_spi; > struct davinci_spi_platform_data *pdata; > + struct davinci_spi_config *spi_cfg; > u8 bits_per_word = 0; > - u32 hz = 0, prescale = 0, clkspeed; > + u32 hz = 0, spifmt = 0, prescale, delay = 0; > > davinci_spi = spi_master_get_devdata(spi->master); > pdata = davinci_spi->pdata; > + spi_cfg = spi->controller_data; > > if (t) { > bits_per_word = t->bits_per_word; > @@ -322,76 +354,112 @@ static int davinci_spi_setup_transfer(struct spi_device *spi, > if (bits_per_word <= 8 && bits_per_word >= 2) { > davinci_spi->get_rx = davinci_spi_rx_buf_u8; > davinci_spi->get_tx = davinci_spi_tx_buf_u8; > - davinci_spi->slave[spi->chip_select].bytes_per_word = 1; > + spi_cfg->bytes_per_word = 1; > } else if (bits_per_word <= 16 && bits_per_word >= 2) { > davinci_spi->get_rx = davinci_spi_rx_buf_u16; > davinci_spi->get_tx = davinci_spi_tx_buf_u16; > - davinci_spi->slave[spi->chip_select].bytes_per_word = 2; > + spi_cfg->bytes_per_word = 2; > } else > return -EINVAL; > > if (!hz) > hz = spi->max_speed_hz; > > - clear_fmt_bits(davinci_spi->base, SPIFMT_CHARLEN_MASK, > - spi->chip_select); > - set_fmt_bits(davinci_spi->base, bits_per_word & 0x1f, > - spi->chip_select); > + prescale = davinci_spi_get_prescale(davinci_spi, hz); > + spifmt |= (prescale << SPIFMT_PRESCALE_SHIFT); > + > + spifmt |= (bits_per_word & 0x1f); > + > + if (spi->mode & SPI_LSB_FIRST) > + spifmt |= SPIFMT_SHIFTDIR_MASK; > > - clkspeed = clk_get_rate(davinci_spi->clk); > - if (hz > clkspeed / 2) > - prescale = 1 << 8; > - if (hz < clkspeed / 256) > - prescale = 255 << 8; > - if (!prescale) > - prescale = ((clkspeed / hz - 1) << 8) & 0x0000ff00; > + if (spi->mode & SPI_CPOL) > + spifmt |= SPIFMT_POLARITY_MASK; > > - clear_fmt_bits(davinci_spi->base, 0x0000ff00, spi->chip_select); > - set_fmt_bits(davinci_spi->base, prescale, spi->chip_select); > + if (!(spi->mode & SPI_CPHA)) > + spifmt |= SPIFMT_PHASE_MASK; > + > + if (davinci_spi->version == SPI_VERSION_2) { > + spifmt |= ((spi_cfg->wdelay << SPIFMT_WDELAY_SHIFT) > + & SPIFMT_WDELAY_MASK); > + > + if (spi_cfg->odd_parity) > + spifmt |= SPIFMT_ODD_PARITY_MASK; > + > + if (spi_cfg->parity_enable) > + spifmt |= SPIFMT_PARITYENA_MASK; > + > + if (spi->mode & SPI_READY) { > + spifmt |= SPIFMT_WAITENA_MASK; > + delay |= (spi_cfg->t2e_delay > + << SPIDELAY_T2EDELAY_SHIFT) > + & SPIDELAY_T2EDELAY_MASK; > + delay |= (spi_cfg->c2e_delay > + << SPIDELAY_C2EDELAY_SHIFT) > + & SPIDELAY_C2EDELAY_MASK; > + } > + > + if (spi_cfg->timer_disable) { > + spifmt |= SPIFMT_DISTIMER_MASK; > + } else { > + delay |= (spi_cfg->c2t_delay > + << SPIDELAY_C2TDELAY_SHIFT) > + & SPIDELAY_C2TDELAY_MASK; > + delay |= (spi_cfg->t2c_delay > + << SPIDELAY_T2CDELAY_SHIFT) > + & SPIDELAY_T2CDELAY_MASK; > + } > + > + iowrite32(delay, davinci_spi->base + SPIDELAY); > + } > + > + iowrite32(spifmt, davinci_spi->base + SPIFMT0); > + > + if (spi_cfg->intr_level) > + iowrite32(SPI_INTLVL_1, davinci_spi->base + SPILVL); > + else > + iowrite32(SPI_INTLVL_0, davinci_spi->base + SPILVL); > + > + if (spi->mode & SPI_LOOP) > + set_io_bits(davinci_spi->base + SPIGCR1, > + SPIGCR1_LOOPBACK_MASK); > + else > + clear_io_bits(davinci_spi->base + SPIGCR1, > + SPIGCR1_LOOPBACK_MASK); > > return 0; > } > > static void davinci_spi_dma_rx_callback(unsigned lch, u16 ch_status, void *data) > { > - struct spi_device *spi = (struct spi_device *)data; > - struct davinci_spi *davinci_spi; > + struct davinci_spi *davinci_spi = (struct davinci_spi *)data; > struct davinci_spi_dma *davinci_spi_dma; > struct davinci_spi_platform_data *pdata; > > - davinci_spi = spi_master_get_devdata(spi->master); > - davinci_spi_dma = &(davinci_spi->dma_channels[spi->chip_select]); > + davinci_spi_dma = &(davinci_spi->dma_channels); > pdata = davinci_spi->pdata; > > + edma_stop(davinci_spi_dma->dma_rx_channel); > + > if (ch_status == DMA_COMPLETE) > - edma_stop(davinci_spi_dma->dma_rx_channel); > - else > - edma_clean_channel(davinci_spi_dma->dma_rx_channel); > + davinci_spi->rcount = 0; > > - complete(&davinci_spi_dma->dma_rx_completion); > - /* We must disable the DMA RX request */ > - davinci_spi_set_dma_req(spi, 0); > + complete(&davinci_spi->done); > } > > static void davinci_spi_dma_tx_callback(unsigned lch, u16 ch_status, void *data) > { > - struct spi_device *spi = (struct spi_device *)data; > - struct davinci_spi *davinci_spi; > + struct davinci_spi *davinci_spi = (struct davinci_spi *)data; > struct davinci_spi_dma *davinci_spi_dma; > struct davinci_spi_platform_data *pdata; > > - davinci_spi = spi_master_get_devdata(spi->master); > - davinci_spi_dma = &(davinci_spi->dma_channels[spi->chip_select]); > + davinci_spi_dma = &(davinci_spi->dma_channels); > pdata = davinci_spi->pdata; > > - if (ch_status == DMA_COMPLETE) > - edma_stop(davinci_spi_dma->dma_tx_channel); > - else > - edma_clean_channel(davinci_spi_dma->dma_tx_channel); > + edma_stop(davinci_spi_dma->dma_tx_channel); > > - complete(&davinci_spi_dma->dma_tx_completion); > - /* We must disable the DMA TX request */ > - davinci_spi_set_dma_req(spi, 0); > + if (ch_status == DMA_COMPLETE) > + davinci_spi->wcount = 0; > } > > static int davinci_spi_request_dma(struct spi_device *spi) > @@ -403,33 +471,54 @@ static int davinci_spi_request_dma(struct spi_device *spi) > int r; > > davinci_spi = spi_master_get_devdata(spi->master); > - davinci_spi_dma = &davinci_spi->dma_channels[spi->chip_select]; > + davinci_spi_dma = &davinci_spi->dma_channels; > pdata = davinci_spi->pdata; > sdev = davinci_spi->bitbang.master->dev.parent; > > r = edma_alloc_channel(davinci_spi_dma->dma_rx_sync_dev, > - davinci_spi_dma_rx_callback, spi, > + davinci_spi_dma_rx_callback, davinci_spi, > davinci_spi_dma->eventq); > if (r < 0) { > - dev_dbg(sdev, "Unable to request DMA channel for SPI RX\n"); > - return -EAGAIN; > + dev_dbg(sdev, "Unable to request DMA channel for MibSPI RX\n"); > + r = -EAGAIN; > + goto rx_dma_failed; > } > davinci_spi_dma->dma_rx_channel = r; > + > r = edma_alloc_channel(davinci_spi_dma->dma_tx_sync_dev, > - davinci_spi_dma_tx_callback, spi, > + davinci_spi_dma_tx_callback, davinci_spi, > davinci_spi_dma->eventq); > if (r < 0) { > - edma_free_channel(davinci_spi_dma->dma_rx_channel); > - davinci_spi_dma->dma_rx_channel = -1; > - dev_dbg(sdev, "Unable to request DMA channel for SPI TX\n"); > - return -EAGAIN; > + dev_dbg(sdev, "Unable to request DMA channel for MibSPI TX\n"); > + r = -EAGAIN; > + goto tx_dma_failed; > } > davinci_spi_dma->dma_tx_channel = r; > > + r = edma_alloc_slot(EDMA_CTLR(davinci_spi_dma->dma_tx_sync_dev), > + EDMA_SLOT_ANY); > + if (r < 0) { > + dev_dbg(sdev, "Unable to request SPI DMA param slot\n"); > + r = -EAGAIN; > + goto param_failed; > + } > + davinci_spi_dma->dummy_param_slot = r; > + edma_link(davinci_spi_dma->dummy_param_slot, > + davinci_spi_dma->dummy_param_slot); > + > return 0; > + > +param_failed: > + edma_free_channel(davinci_spi_dma->dma_tx_channel); > + davinci_spi_dma->dma_tx_channel = -1; > +tx_dma_failed: > + edma_free_channel(davinci_spi_dma->dma_rx_channel); > + davinci_spi_dma->dma_rx_channel = -1; > +rx_dma_failed: > + return r; > } > > -/** > +/* > * davinci_spi_setup - This functions will set default transfer method > * @spi: spi device on which data transfer to be done > * > @@ -438,129 +527,54 @@ static int davinci_spi_request_dma(struct spi_device *spi) > > static int davinci_spi_setup(struct spi_device *spi) > { > - int retval; > + int retval = 0; > struct davinci_spi *davinci_spi; > - struct davinci_spi_dma *davinci_spi_dma; > - struct device *sdev; > + struct davinci_spi_dma *davinci_dma; > + struct davinci_spi_platform_data *pdata; > + struct davinci_spi_config *spi_cfg; > + u32 prescale; > > davinci_spi = spi_master_get_devdata(spi->master); > - sdev = davinci_spi->bitbang.master->dev.parent; > + pdata = davinci_spi->pdata; > + spi_cfg = (struct davinci_spi_config *)spi->controller_data; > + davinci_dma = &(davinci_spi->dma_channels); > > /* if bits per word length is zero then set it default 8 */ > if (!spi->bits_per_word) > spi->bits_per_word = 8; > > - davinci_spi->slave[spi->chip_select].cmd_to_write = 0; > - > - if (use_dma && davinci_spi->dma_channels) { > - davinci_spi_dma = &davinci_spi->dma_channels[spi->chip_select]; > - > - if ((davinci_spi_dma->dma_rx_channel == -1) > - || (davinci_spi_dma->dma_tx_channel == -1)) { > - retval = davinci_spi_request_dma(spi); > - if (retval < 0) > - return retval; > - } > - } > + if (!(spi->mode & SPI_NO_CS)) { > + if ((pdata->chip_sel == NULL) || > + (pdata->chip_sel[spi->chip_select] == SPI_INTERN_CS)) > + set_io_bits(davinci_spi->base + SPIPC0, > + 1 << spi->chip_select); > > - /* > - * SPI in DaVinci and DA8xx operate between > - * 600 KHz and 50 MHz > - */ > - if (spi->max_speed_hz < 600000 || spi->max_speed_hz > 50000000) { > - dev_dbg(sdev, "Operating frequency is not in acceptable " > - "range\n"); > - return -EINVAL; > } > > - /* > - * Set up SPIFMTn register, unique to this chipselect. > - * > - * NOTE: we could do all of these with one write. Also, some > - * of the "version 2" features are found in chips that don't > - * support all of them... > - */ > - if (spi->mode & SPI_LSB_FIRST) > - set_fmt_bits(davinci_spi->base, SPIFMT_SHIFTDIR_MASK, > - spi->chip_select); > - else > - clear_fmt_bits(davinci_spi->base, SPIFMT_SHIFTDIR_MASK, > - spi->chip_select); > + if (spi->mode & SPI_READY) > + set_io_bits(davinci_spi->base + SPIPC0, SPIPC0_SPIENA_MASK); > > - if (spi->mode & SPI_CPOL) > - set_fmt_bits(davinci_spi->base, SPIFMT_POLARITY_MASK, > - spi->chip_select); > - else > - clear_fmt_bits(davinci_spi->base, SPIFMT_POLARITY_MASK, > - spi->chip_select); > + if (spi_cfg->io_type == SPI_IO_TYPE_DMA) { > + davinci_dma = &(davinci_spi->dma_channels); > > - if (!(spi->mode & SPI_CPHA)) > - set_fmt_bits(davinci_spi->base, SPIFMT_PHASE_MASK, > - spi->chip_select); > - else > - clear_fmt_bits(davinci_spi->base, SPIFMT_PHASE_MASK, > - spi->chip_select); > + if ((davinci_dma->dma_tx_sync_dev == DAVINCI_SPI_NO_RESOURCE) || > + (davinci_dma->dma_rx_sync_dev == DAVINCI_SPI_NO_RESOURCE) || > + (davinci_dma->eventq == DAVINCI_SPI_NO_RESOURCE)) > + spi_cfg->io_type = SPI_IO_TYPE_INTR; > + else if ((davinci_dma->dma_rx_channel == -1) || > + (davinci_dma->dma_tx_channel == -1)) > + retval = davinci_spi_request_dma(spi); > + } > > /* > - * Version 1 hardware supports two basic SPI modes: > - * - Standard SPI mode uses 4 pins, with chipselect > - * - 3 pin SPI is a 4 pin variant without CS (SPI_NO_CS) > - * (distinct from SPI_3WIRE, with just one data wire; > - * or similar variants without MOSI or without MISO) > - * > - * Version 2 hardware supports an optional handshaking signal, > - * so it can support two more modes: > - * - 5 pin SPI variant is standard SPI plus SPI_READY > - * - 4 pin with enable is (SPI_READY | SPI_NO_CS) > + * Validate desired clock rate > */ > + prescale = davinci_spi_get_prescale(davinci_spi, spi->max_speed_hz); > + if ((prescale < 2) || (prescale > 255)) > + return -EINVAL; > > - if (davinci_spi->version == SPI_VERSION_2) { > - clear_fmt_bits(davinci_spi->base, SPIFMT_WDELAY_MASK, > - spi->chip_select); > - set_fmt_bits(davinci_spi->base, > - (davinci_spi->pdata->wdelay > - << SPIFMT_WDELAY_SHIFT) > - & SPIFMT_WDELAY_MASK, > - spi->chip_select); > - > - if (davinci_spi->pdata->odd_parity) > - set_fmt_bits(davinci_spi->base, > - SPIFMT_ODD_PARITY_MASK, > - spi->chip_select); > - else > - clear_fmt_bits(davinci_spi->base, > - SPIFMT_ODD_PARITY_MASK, > - spi->chip_select); > - > - if (davinci_spi->pdata->parity_enable) > - set_fmt_bits(davinci_spi->base, > - SPIFMT_PARITYENA_MASK, > - spi->chip_select); > - else > - clear_fmt_bits(davinci_spi->base, > - SPIFMT_PARITYENA_MASK, > - spi->chip_select); > - > - if (davinci_spi->pdata->wait_enable) > - set_fmt_bits(davinci_spi->base, > - SPIFMT_WAITENA_MASK, > - spi->chip_select); > - else > - clear_fmt_bits(davinci_spi->base, > - SPIFMT_WAITENA_MASK, > - spi->chip_select); > - > - if (davinci_spi->pdata->timer_disable) > - set_fmt_bits(davinci_spi->base, > - SPIFMT_DISTIMER_MASK, > - spi->chip_select); > - else > - clear_fmt_bits(davinci_spi->base, > - SPIFMT_DISTIMER_MASK, > - spi->chip_select); > - } > - > - retval = davinci_spi_setup_transfer(spi, NULL); > + dev_info(&spi->dev, "DaVinci SPI driver in %s mode\n", > + io_type_names[spi_cfg->io_type]); > > return retval; > } > @@ -569,50 +583,19 @@ static void davinci_spi_cleanup(struct spi_device *spi) > { > struct davinci_spi *davinci_spi = spi_master_get_devdata(spi->master); > struct davinci_spi_dma *davinci_spi_dma; > + struct davinci_spi_platform_data *pdata; > > - davinci_spi_dma = &davinci_spi->dma_channels[spi->chip_select]; > - > - if (use_dma && davinci_spi->dma_channels) { > - davinci_spi_dma = &davinci_spi->dma_channels[spi->chip_select]; > - > - if ((davinci_spi_dma->dma_rx_channel != -1) > - && (davinci_spi_dma->dma_tx_channel != -1)) { > - edma_free_channel(davinci_spi_dma->dma_tx_channel); > - edma_free_channel(davinci_spi_dma->dma_rx_channel); > - } > - } > -} > - > -static int davinci_spi_bufs_prep(struct spi_device *spi, > - struct davinci_spi *davinci_spi) > -{ > - int op_mode = 0; > - > - /* > - * REVISIT unless devices disagree about SPI_LOOP or > - * SPI_READY (SPI_NO_CS only allows one device!), this > - * should not need to be done before each message... > - * optimize for both flags staying cleared. > - */ > - > - op_mode = SPIPC0_DIFUN_MASK > - | SPIPC0_DOFUN_MASK > - | SPIPC0_CLKFUN_MASK; > - if (!(spi->mode & SPI_NO_CS)) > - op_mode |= 1 << spi->chip_select; > - if (spi->mode & SPI_READY) > - op_mode |= SPIPC0_SPIENA_MASK; > + davinci_spi_dma = &davinci_spi->dma_channels; > + pdata = davinci_spi->pdata; > > - iowrite32(op_mode, davinci_spi->base + SPIPC0); > + if (davinci_spi_dma->dma_rx_channel != -1) > + edma_free_channel(davinci_spi_dma->dma_rx_channel); > > - if (spi->mode & SPI_LOOP) > - set_io_bits(davinci_spi->base + SPIGCR1, > - SPIGCR1_LOOPBACK_MASK); > - else > - clear_io_bits(davinci_spi->base + SPIGCR1, > - SPIGCR1_LOOPBACK_MASK); > + if (davinci_spi_dma->dma_tx_channel != -1) > + edma_free_channel(davinci_spi_dma->dma_tx_channel); > > - return 0; > + if (davinci_spi_dma->dummy_param_slot != -1) > + edma_free_slot(davinci_spi_dma->dummy_param_slot); > } > > static int davinci_spi_check_error(struct davinci_spi *davinci_spi, > @@ -659,356 +642,248 @@ static int davinci_spi_check_error(struct davinci_spi *davinci_spi, > return 0; > } > > -/** > - * davinci_spi_bufs - functions which will handle transfer data > - * @spi: spi device on which data transfer to be done > - * @t: spi transfer in which transfer info is filled > +/* > + * davinci_spi_process_events - check for and handle any SPI controller events > + * @davinci_spi - the controller data > * > - * This function will put data to be transferred into data register > - * of SPI controller and then wait until the completion will be marked > - * by the IRQ Handler. > + * This function will check the SPIFLG register and handle any events that are > + * detected there > */ > -static int davinci_spi_bufs_pio(struct spi_device *spi, struct spi_transfer *t) > +static int davinci_spi_process_events(struct davinci_spi *davinci_spi) > { > - struct davinci_spi *davinci_spi; > - int int_status, count, ret; > - u8 conv, tmp; > - u32 tx_data, data1_reg_val; > - u32 buf_val, flg_val; > - struct davinci_spi_platform_data *pdata; > - > - davinci_spi = spi_master_get_devdata(spi->master); > - pdata = davinci_spi->pdata; > - > - davinci_spi->tx = t->tx_buf; > - davinci_spi->rx = t->rx_buf; > - > - /* convert len to words based on bits_per_word */ > - conv = davinci_spi->slave[spi->chip_select].bytes_per_word; > - davinci_spi->count = t->len / conv; > - > - INIT_COMPLETION(davinci_spi->done); > - > - ret = davinci_spi_bufs_prep(spi, davinci_spi); > - if (ret) > - return ret; > - > - /* Enable SPI */ > - set_io_bits(davinci_spi->base + SPIGCR1, SPIGCR1_SPIENA_MASK); > - > - iowrite32(0 | (pdata->c2tdelay << SPI_C2TDELAY_SHIFT) | > - (pdata->t2cdelay << SPI_T2CDELAY_SHIFT), > - davinci_spi->base + SPIDELAY); > - > - count = davinci_spi->count; > - data1_reg_val = pdata->cs_hold << SPIDAT1_CSHOLD_SHIFT; > - tmp = ~(0x1 << spi->chip_select); > - > - clear_io_bits(davinci_spi->base + SPIDEF, ~tmp); > - > - data1_reg_val |= tmp << SPIDAT1_CSNR_SHIFT; > - > - while ((ioread32(davinci_spi->base + SPIBUF) > - & SPIBUF_RXEMPTY_MASK) == 0) > - cpu_relax(); > - > - /* Determine the command to execute READ or WRITE */ > - if (t->tx_buf) { > - clear_io_bits(davinci_spi->base + SPIINT, SPIINT_MASKALL); > - > - while (1) { > - tx_data = davinci_spi->get_tx(davinci_spi); > - > - data1_reg_val &= ~(0xFFFF); > - data1_reg_val |= (0xFFFF & tx_data); > - > - buf_val = ioread32(davinci_spi->base + SPIBUF); > - if ((buf_val & SPIBUF_TXFULL_MASK) == 0) { > - iowrite32(data1_reg_val, > - davinci_spi->base + SPIDAT1); > - > - count--; > - } > - while (ioread32(davinci_spi->base + SPIBUF) > - & SPIBUF_RXEMPTY_MASK) > - cpu_relax(); > - > - /* getting the returned byte */ > - if (t->rx_buf) { > - buf_val = ioread32(davinci_spi->base + SPIBUF); > - davinci_spi->get_rx(buf_val, davinci_spi); > - } > - if (count <= 0) > - break; > - } > - } else { > - if (pdata->poll_mode) { > - while (1) { > - /* keeps the serial clock going */ > - if ((ioread32(davinci_spi->base + SPIBUF) > - & SPIBUF_TXFULL_MASK) == 0) > - iowrite32(data1_reg_val, > - davinci_spi->base + SPIDAT1); > - > - while (ioread32(davinci_spi->base + SPIBUF) & > - SPIBUF_RXEMPTY_MASK) > - cpu_relax(); > - > - flg_val = ioread32(davinci_spi->base + SPIFLG); > - buf_val = ioread32(davinci_spi->base + SPIBUF); > - > - davinci_spi->get_rx(buf_val, davinci_spi); > - > - count--; > - if (count <= 0) > - break; > - } > - } else { /* Receive in Interrupt mode */ > - int i; > - > - for (i = 0; i < davinci_spi->count; i++) { > - set_io_bits(davinci_spi->base + SPIINT, > - SPIINT_BITERR_INTR > - | SPIINT_OVRRUN_INTR > - | SPIINT_RX_INTR); > - > - iowrite32(data1_reg_val, > - davinci_spi->base + SPIDAT1); > - > - while (ioread32(davinci_spi->base + SPIINT) & > - SPIINT_RX_INTR) > - cpu_relax(); > - } > - iowrite32((data1_reg_val & 0x0ffcffff), > - davinci_spi->base + SPIDAT1); > - } > + u32 status, tx_data, rx_data, spidat1; > + u8 tx_word = 0; > + > + status = ioread32(davinci_spi->base + SPIFLG); > + > + if ((davinci_spi->version == SPI_VERSION_2) && > + (likely(status & SPIFLG_TX_INTR_MASK)) && > + (likely(davinci_spi->wcount > 0))) > + tx_word = 1; > + > + if (likely(status & SPIFLG_RX_INTR_MASK)) { > + rx_data = ioread32(davinci_spi->base + SPIBUF) & 0xFFFF; > + davinci_spi->get_rx(rx_data, davinci_spi); > + davinci_spi->rcount--; > + if ((davinci_spi->version != SPI_VERSION_2) && > + (likely(davinci_spi->wcount > 0))) > + tx_word = 1; > } > > - /* > - * Check for bit error, desync error,parity error,timeout error and > - * receive overflow errors > - */ > - int_status = ioread32(davinci_spi->base + SPIFLG); > - > - ret = davinci_spi_check_error(davinci_spi, int_status); > - if (ret != 0) > - return ret; > + if (unlikely(status & SPIFLG_ERROR_MASK)) { > + davinci_spi->errors = (status & SPIFLG_ERROR_MASK); > + return -1; > + } > > - /* SPI Framework maintains the count only in bytes so convert back */ > - davinci_spi->count *= conv; > + if (likely(tx_word)) { > + spidat1 = ioread32(davinci_spi->base + SPIDAT1); > + davinci_spi->wcount--; > + tx_data = davinci_spi->get_tx(davinci_spi); > + spidat1 &= 0xFFFF0000; > + spidat1 |= (tx_data & 0xFFFF); > + iowrite32(spidat1, davinci_spi->base + SPIDAT1); > + } > > - return t->len; > + return 0; > } > > -#define DAVINCI_DMA_DATA_TYPE_S8 0x01 > -#define DAVINCI_DMA_DATA_TYPE_S16 0x02 > -#define DAVINCI_DMA_DATA_TYPE_S32 0x04 > - > -static int davinci_spi_bufs_dma(struct spi_device *spi, struct spi_transfer *t) > +/* > + * davinci_spi_txrx_bufs - function which will handle transfer data > + * @spi: spi device on which data transfer to be done > + * @t: spi transfer in which transfer info is filled > + * > + * This function will put data to be transferred into data register > + * of SPI controller and then wait until the completion will be marked > + * by the IRQ Handler. > + */ > +static int davinci_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t) > { > struct davinci_spi *davinci_spi; > - int int_status = 0; > - int count, temp_count; > - u8 conv = 1; > - u8 tmp; > - u32 data1_reg_val; > - struct davinci_spi_dma *davinci_spi_dma; > - int word_len, data_type, ret; > - unsigned long tx_reg, rx_reg; > + int data_type, ret = 0; > + u32 tx_data, spidat1; > + u16 tx_buf_count = 0, rx_buf_count = 0; > + struct davinci_spi_config *spi_cfg; > struct davinci_spi_platform_data *pdata; > + struct davinci_spi_dma *davinci_dma; > struct device *sdev; > + dma_addr_t tx_reg, rx_reg; > + void *tx_buf, *rx_buf; > + struct edmacc_param rx_param, tx_param; > > davinci_spi = spi_master_get_devdata(spi->master); > pdata = davinci_spi->pdata; > - sdev = davinci_spi->bitbang.master->dev.parent; > - > - davinci_spi_dma = &davinci_spi->dma_channels[spi->chip_select]; > - > - tx_reg = (unsigned long)davinci_spi->pbase + SPIDAT1; > - rx_reg = (unsigned long)davinci_spi->pbase + SPIBUF; > + spi_cfg = (struct davinci_spi_config *)spi->controller_data; > + davinci_dma = &(davinci_spi->dma_channels); > > davinci_spi->tx = t->tx_buf; > davinci_spi->rx = t->rx_buf; > + davinci_spi->wcount = t->len / spi_cfg->bytes_per_word; > + davinci_spi->rcount = davinci_spi->wcount; > + davinci_spi->errors = 0; > > - /* convert len to words based on bits_per_word */ > - conv = davinci_spi->slave[spi->chip_select].bytes_per_word; > - davinci_spi->count = t->len / conv; > - > - INIT_COMPLETION(davinci_spi->done); > + spidat1 = ioread32(davinci_spi->base + SPIDAT1); > > - init_completion(&davinci_spi_dma->dma_rx_completion); > - init_completion(&davinci_spi_dma->dma_tx_completion); > - > - word_len = conv * 8; > - > - if (word_len <= 8) > - data_type = DAVINCI_DMA_DATA_TYPE_S8; > - else if (word_len <= 16) > - data_type = DAVINCI_DMA_DATA_TYPE_S16; > - else if (word_len <= 32) > - data_type = DAVINCI_DMA_DATA_TYPE_S32; > - else > - return -EINVAL; > - > - ret = davinci_spi_bufs_prep(spi, davinci_spi); > - if (ret) > - return ret; > - > - /* Put delay val if required */ > - iowrite32(0 | (pdata->c2tdelay << SPI_C2TDELAY_SHIFT) | > - (pdata->t2cdelay << SPI_T2CDELAY_SHIFT), > - davinci_spi->base + SPIDELAY); > - > - count = davinci_spi->count; /* the number of elements */ > - data1_reg_val = pdata->cs_hold << SPIDAT1_CSHOLD_SHIFT; > - > - /* CS default = 0xFF */ > - tmp = ~(0x1 << spi->chip_select); > - > - clear_io_bits(davinci_spi->base + SPIDEF, ~tmp); > - > - data1_reg_val |= tmp << SPIDAT1_CSNR_SHIFT; > - > - /* disable all interrupts for dma transfers */ > - clear_io_bits(davinci_spi->base + SPIINT, SPIINT_MASKALL); > - /* Disable SPI to write configuration bits in SPIDAT */ > - clear_io_bits(davinci_spi->base + SPIGCR1, SPIGCR1_SPIENA_MASK); > - iowrite32(data1_reg_val, davinci_spi->base + SPIDAT1); > - /* Enable SPI */ > + clear_io_bits(davinci_spi->base + SPIGCR1, SPIGCR1_POWERDOWN_MASK); > set_io_bits(davinci_spi->base + SPIGCR1, SPIGCR1_SPIENA_MASK); > > - while ((ioread32(davinci_spi->base + SPIBUF) > - & SPIBUF_RXEMPTY_MASK) == 0) > - cpu_relax(); > - > + INIT_COMPLETION(davinci_spi->done); > > - if (t->tx_buf) { > - t->tx_dma = dma_map_single(&spi->dev, (void *)t->tx_buf, count, > - DMA_TO_DEVICE); > - if (dma_mapping_error(&spi->dev, t->tx_dma)) { > - dev_dbg(sdev, "Unable to DMA map a %d bytes" > - " TX buffer\n", count); > - return -ENOMEM; > + if ((spi_cfg->io_type == SPI_IO_TYPE_INTR) || > + (spi_cfg->io_type == SPI_IO_TYPE_POLL)) { > + > + if (spi_cfg->io_type == SPI_IO_TYPE_INTR) > + set_io_bits(davinci_spi->base + SPIINT, SPIINT_MASKINT); > + > + /* start the transfer */ > + davinci_spi->wcount--; > + tx_data = davinci_spi->get_tx(davinci_spi); > + spidat1 &= 0xFFFF0000; > + spidat1 |= (tx_data & 0xFFFF); > + iowrite32(spidat1, davinci_spi->base + SPIDAT1); > + > + } else if (spi_cfg->io_type == SPI_IO_TYPE_DMA) { > + data_type = spi_cfg->bytes_per_word; > + tx_reg = (dma_addr_t)davinci_spi->pbase + SPIDAT1; > + rx_reg = (dma_addr_t)davinci_spi->pbase + SPIBUF; > + > + if (t->tx_buf) { > + tx_buf = ((void *)t->tx_buf); > + tx_buf_count = davinci_spi->wcount; > + } else { > + tx_buf = (void *)davinci_spi->tmp_buf; > + tx_buf_count = SPI_BUFSIZ; > } > - temp_count = count; > - } else { > - /* We need TX clocking for RX transaction */ > - t->tx_dma = dma_map_single(&spi->dev, > - (void *)davinci_spi->tmp_buf, count + 1, > - DMA_TO_DEVICE); > - if (dma_mapping_error(&spi->dev, t->tx_dma)) { > - dev_dbg(sdev, "Unable to DMA map a %d bytes" > - " TX tmp buffer\n", count); > - return -ENOMEM; > + if (t->rx_buf) { > + rx_buf = (void *)t->rx_buf; > + rx_buf_count = davinci_spi->rcount; > + } else { > + rx_buf = (void *)davinci_spi->tmp_buf; > + rx_buf_count = SPI_BUFSIZ; > } > - temp_count = count + 1; > + > + t->tx_dma = dma_map_single(&spi->dev, tx_buf, > + tx_buf_count, DMA_TO_DEVICE); > + t->rx_dma = dma_map_single(&spi->dev, rx_buf, > + rx_buf_count, DMA_FROM_DEVICE); > + > + tx_param.opt = TCINTEN | EDMA_TCC(davinci_dma->dma_tx_channel); > + tx_param.src = t->tx_buf ? t->tx_dma : tx_reg; > + tx_param.a_b_cnt = davinci_spi->wcount << 16 | data_type; > + tx_param.dst = tx_reg; > + tx_param.src_dst_bidx = t->tx_buf ? data_type : 0; > + tx_param.link_bcntrld = 0xffff; > + tx_param.src_dst_cidx = 0; > + tx_param.ccnt = 1; > + edma_write_slot(davinci_dma->dma_tx_channel, &tx_param); > + edma_link(davinci_dma->dma_tx_channel, > + davinci_dma->dummy_param_slot); > + > + rx_param.opt = TCINTEN | EDMA_TCC(davinci_dma->dma_rx_channel); > + rx_param.src = rx_reg; > + rx_param.a_b_cnt = davinci_spi->rcount << 16 | data_type; > + rx_param.dst = t->rx_dma; > + rx_param.src_dst_bidx = (t->rx_buf ? data_type : 0) << 16; > + rx_param.link_bcntrld = 0xffff; > + rx_param.src_dst_cidx = 0; > + rx_param.ccnt = 1; > + edma_write_slot(davinci_dma->dma_rx_channel, &rx_param); > + > + iowrite16(spidat1 >> SPIDAT1_CSNR_SHIFT, > + davinci_spi->base + SPIDAT1 + 2); > + > + edma_start(davinci_dma->dma_rx_channel); > + edma_start(davinci_dma->dma_tx_channel); > + set_io_bits(davinci_spi->base + SPIINT, SPIINT_DMA_REQ_EN); > } > > - edma_set_transfer_params(davinci_spi_dma->dma_tx_channel, > - data_type, temp_count, 1, 0, ASYNC); > - edma_set_dest(davinci_spi_dma->dma_tx_channel, tx_reg, INCR, W8BIT); > - edma_set_src(davinci_spi_dma->dma_tx_channel, t->tx_dma, INCR, W8BIT); > - edma_set_src_index(davinci_spi_dma->dma_tx_channel, data_type, 0); > - edma_set_dest_index(davinci_spi_dma->dma_tx_channel, 0, 0); > - > - if (t->rx_buf) { > - /* initiate transaction */ > - iowrite32(data1_reg_val, davinci_spi->base + SPIDAT1); > - > - t->rx_dma = dma_map_single(&spi->dev, (void *)t->rx_buf, count, > - DMA_FROM_DEVICE); > - if (dma_mapping_error(&spi->dev, t->rx_dma)) { > - dev_dbg(sdev, "Couldn't DMA map a %d bytes RX buffer\n", > - count); > - if (t->tx_buf != NULL) > - dma_unmap_single(NULL, t->tx_dma, > - count, DMA_TO_DEVICE); > - return -ENOMEM; > + /* Wait for the transfer to complete */ > + if (spi_cfg->io_type != SPI_IO_TYPE_POLL) { > + wait_for_completion_interruptible(&(davinci_spi->done)); > + } else { > + while ((davinci_spi->rcount > 0) && (ret == 0)) { > + ret = davinci_spi_process_events(davinci_spi); > + cpu_relax(); > } > - edma_set_transfer_params(davinci_spi_dma->dma_rx_channel, > - data_type, count, 1, 0, ASYNC); > - edma_set_src(davinci_spi_dma->dma_rx_channel, > - rx_reg, INCR, W8BIT); > - edma_set_dest(davinci_spi_dma->dma_rx_channel, > - t->rx_dma, INCR, W8BIT); > - edma_set_src_index(davinci_spi_dma->dma_rx_channel, 0, 0); > - edma_set_dest_index(davinci_spi_dma->dma_rx_channel, > - data_type, 0); > } > > - if ((t->tx_buf) || (t->rx_buf)) > - edma_start(davinci_spi_dma->dma_tx_channel); > - > - if (t->rx_buf) > - edma_start(davinci_spi_dma->dma_rx_channel); > - > - if ((t->rx_buf) || (t->tx_buf)) > - davinci_spi_set_dma_req(spi, 1); > - > - if (t->tx_buf) > - wait_for_completion_interruptible( > - &davinci_spi_dma->dma_tx_completion); > - > - if (t->rx_buf) > - wait_for_completion_interruptible( > - &davinci_spi_dma->dma_rx_completion); > - > - dma_unmap_single(NULL, t->tx_dma, temp_count, DMA_TO_DEVICE); > - > - if (t->rx_buf) > - dma_unmap_single(NULL, t->rx_dma, count, DMA_FROM_DEVICE); > - > - /* > - * Check for bit error, desync error,parity error,timeout error and > - * receive overflow errors > - */ > - int_status = ioread32(davinci_spi->base + SPIFLG); > + clear_io_bits(davinci_spi->base + SPIINT, SPIINT_MASKALL); > + if (spi_cfg->io_type == SPI_IO_TYPE_DMA) { > + dma_unmap_single(NULL, t->tx_dma, tx_buf_count, > + DMA_TO_DEVICE); > + dma_unmap_single(NULL, t->rx_dma, rx_buf_count, > + DMA_FROM_DEVICE); > + } > > - ret = davinci_spi_check_error(davinci_spi, int_status); > - if (ret != 0) > - return ret; > + clear_io_bits(davinci_spi->base + SPIGCR1, SPIGCR1_SPIENA_MASK); > + set_io_bits(davinci_spi->base + SPIGCR1, SPIGCR1_POWERDOWN_MASK); > > - /* SPI Framework maintains the count only in bytes so convert back */ > - davinci_spi->count *= conv; > + if (davinci_spi->errors) { > + ret = davinci_spi_check_error(davinci_spi, davinci_spi->errors); > + if (ret != 0) > + return ret; > + } > + if ((davinci_spi->rcount != 0) || (davinci_spi->wcount != 0)) { > + sdev = davinci_spi->bitbang.master->dev.parent; > + dev_info(sdev, "SPI data transfer error\n"); > + return -EIO; > + } > > return t->len; > } > > -/** > - * davinci_spi_irq - IRQ handler for DaVinci SPI > +/* > + * davinci_spi_irq - probe function for SPI Master Controller > * @irq: IRQ number for this SPI Master > * @context_data: structure for SPI Master controller davinci_spi > + * > + * ISR will determine that interrupt arrives either for READ or WRITE command. > + * According to command it will do the appropriate action. It will check > + * transfer length and if it is not zero then dispatch transfer command again. > + * If transfer length is zero then it will indicate the COMPLETION so that > + * davinci_spi_bufs function can go ahead. > */ > static irqreturn_t davinci_spi_irq(s32 irq, void *context_data) > { > struct davinci_spi *davinci_spi = context_data; > - u32 int_status, rx_data = 0; > - irqreturn_t ret = IRQ_NONE; > - > - int_status = ioread32(davinci_spi->base + SPIFLG); > + int status; > > - while ((int_status & SPIFLG_RX_INTR_MASK)) { > - if (likely(int_status & SPIFLG_RX_INTR_MASK)) { > - ret = IRQ_HANDLED; > + status = davinci_spi_process_events(davinci_spi); > + if (unlikely(status != 0)) > + clear_io_bits(davinci_spi->base + SPIINT, SPIINT_MASKINT); > > - rx_data = ioread32(davinci_spi->base + SPIBUF); > - davinci_spi->get_rx(rx_data, davinci_spi); > + if ((davinci_spi->rcount == 0) || (status != 0)) > + complete(&(davinci_spi->done)); > > - /* Disable Receive Interrupt */ > - iowrite32(~(SPIINT_RX_INTR | SPIINT_TX_INTR), > - davinci_spi->base + SPIINT); > - } else > - (void)davinci_spi_check_error(davinci_spi, int_status); > + return IRQ_HANDLED; > +} > > - int_status = ioread32(davinci_spi->base + SPIFLG); > +resource_size_t davinci_spi_get_dma_by_flag(struct platform_device *dev, > + unsigned long flag) > +{ > + struct resource *r; > + int i; > + > + for (i = 0; i < dev->num_resources; i++) { > + r = platform_get_resource(dev, IORESOURCE_DMA, i); > + if (r == NULL) > + break; > + if ((r->flags & flag) == flag) > + return r->start; > } > > - return ret; > + return DAVINCI_SPI_NO_RESOURCE; > } > > -/** > +/* > * davinci_spi_probe - probe function for SPI Master Controller > * @pdev: platform_device structure which contains plateform specific data > + * > + * According to Linux Device Model this function will be invoked by Linux > + * with platform_device struct which contains the device specific info. > + * This function will map the SPI controller's memory, register IRQ, > + * Reset SPI controller and setting its registers to default value. > + * It will invoke spi_bitbang_start to create work queue so that client driver > + * can register transfer method to work queue. > */ > static int davinci_spi_probe(struct platform_device *pdev) > { > @@ -1016,10 +891,11 @@ static int davinci_spi_probe(struct platform_device *pdev) > struct davinci_spi *davinci_spi; > struct davinci_spi_platform_data *pdata; > struct resource *r, *mem; > - resource_size_t dma_rx_chan = SPI_NO_RESOURCE; > - resource_size_t dma_tx_chan = SPI_NO_RESOURCE; > - resource_size_t dma_eventq = SPI_NO_RESOURCE; > + resource_size_t dma_rx_chan = DAVINCI_SPI_NO_RESOURCE; > + resource_size_t dma_tx_chan = DAVINCI_SPI_NO_RESOURCE; > + resource_size_t dma_eventq = DAVINCI_SPI_NO_RESOURCE; > int i = 0, ret = 0; > + u32 spipc0; > > pdata = pdev->dev.platform_data; > if (pdata == NULL) { > @@ -1073,14 +949,16 @@ static int davinci_spi_probe(struct platform_device *pdev) > > ret = request_irq(davinci_spi->irq, davinci_spi_irq, IRQF_DISABLED, > dev_name(&pdev->dev), davinci_spi); > - if (ret) > + if (ret != 0) { > + ret = -EAGAIN; > goto unmap_io; > + } > > /* Allocate tmp_buf for tx_buf */ > davinci_spi->tmp_buf = kzalloc(SPI_BUFSIZ, GFP_KERNEL); > if (davinci_spi->tmp_buf == NULL) { > ret = -ENOMEM; > - goto irq_free; > + goto err1; > } > > davinci_spi->bitbang.master = spi_master_get(master); > @@ -1104,55 +982,23 @@ static int davinci_spi_probe(struct platform_device *pdev) > > davinci_spi->bitbang.chipselect = davinci_spi_chipselect; > davinci_spi->bitbang.setup_transfer = davinci_spi_setup_transfer; > + davinci_spi->bitbang.txrx_bufs = davinci_spi_txrx_bufs; > > davinci_spi->version = pdata->version; > - use_dma = pdata->use_dma; > > davinci_spi->bitbang.flags = SPI_NO_CS | SPI_LSB_FIRST | SPI_LOOP; > if (davinci_spi->version == SPI_VERSION_2) > davinci_spi->bitbang.flags |= SPI_READY; > > - if (use_dma) { > - r = platform_get_resource(pdev, IORESOURCE_DMA, 0); > - if (r) > - dma_rx_chan = r->start; > - r = platform_get_resource(pdev, IORESOURCE_DMA, 1); > - if (r) > - dma_tx_chan = r->start; > - r = platform_get_resource(pdev, IORESOURCE_DMA, 2); > - if (r) > - dma_eventq = r->start; > - } > - > - if (!use_dma || > - dma_rx_chan == SPI_NO_RESOURCE || > - dma_tx_chan == SPI_NO_RESOURCE || > - dma_eventq == SPI_NO_RESOURCE) { > - davinci_spi->bitbang.txrx_bufs = davinci_spi_bufs_pio; > - use_dma = 0; > - } else { > - davinci_spi->bitbang.txrx_bufs = davinci_spi_bufs_dma; > - davinci_spi->dma_channels = kzalloc(master->num_chipselect > - * sizeof(struct davinci_spi_dma), GFP_KERNEL); > - if (davinci_spi->dma_channels == NULL) { > - ret = -ENOMEM; > - goto free_clk; > - } > - > - for (i = 0; i < master->num_chipselect; i++) { > - davinci_spi->dma_channels[i].dma_rx_channel = -1; > - davinci_spi->dma_channels[i].dma_rx_sync_dev = > - dma_rx_chan; > - davinci_spi->dma_channels[i].dma_tx_channel = -1; > - davinci_spi->dma_channels[i].dma_tx_sync_dev = > - dma_tx_chan; > - davinci_spi->dma_channels[i].eventq = dma_eventq; > - } > - dev_info(&pdev->dev, "DaVinci SPI driver in EDMA mode\n" > - "Using RX channel = %d , TX channel = %d and " > - "event queue = %d", dma_rx_chan, dma_tx_chan, > - dma_eventq); > - } > + dma_rx_chan = davinci_spi_get_dma_by_flag(pdev, IORESOURCE_DMA_RX_CHAN); > + dma_tx_chan = davinci_spi_get_dma_by_flag(pdev, IORESOURCE_DMA_TX_CHAN); > + dma_eventq = davinci_spi_get_dma_by_flag(pdev, IORESOURCE_DMA_EVENT_Q); > + davinci_spi->dma_channels.dma_rx_channel = -1; > + davinci_spi->dma_channels.dma_rx_sync_dev = dma_rx_chan; > + davinci_spi->dma_channels.dma_tx_channel = -1; > + davinci_spi->dma_channels.dma_tx_sync_dev = dma_tx_chan; > + davinci_spi->dma_channels.dummy_param_slot = -1; > + davinci_spi->dma_channels.eventq = dma_eventq; > > davinci_spi->get_rx = davinci_spi_rx_buf_u8; > davinci_spi->get_tx = davinci_spi_tx_buf_u8; > @@ -1164,32 +1010,29 @@ static int davinci_spi_probe(struct platform_device *pdev) > udelay(100); > iowrite32(1, davinci_spi->base + SPIGCR0); > > - /* Clock internal */ > - if (davinci_spi->pdata->clk_internal) > - set_io_bits(davinci_spi->base + SPIGCR1, > - SPIGCR1_CLKMOD_MASK); > - else > - clear_io_bits(davinci_spi->base + SPIGCR1, > - SPIGCR1_CLKMOD_MASK); > + /* Set up SPIPC0. CS and ENA init is done in davinci_spi_setup */ > + spipc0 = SPIPC0_DIFUN_MASK | SPIPC0_DOFUN_MASK | SPIPC0_CLKFUN_MASK; > + iowrite32(spipc0, davinci_spi->base + SPIPC0); > > - /* master mode default */ > - set_io_bits(davinci_spi->base + SPIGCR1, SPIGCR1_MASTER_MASK); > + /* initialize chip selects */ > + if (pdata->chip_sel != NULL) { > + for (i = 0; i < pdata->num_chipselect; i++) { > + if (pdata->chip_sel[i] != SPI_INTERN_CS) > + gpio_direction_output(pdata->chip_sel[i], 1); > + } > + } > + iowrite32(SPIDEF_CSDEF_MASK, davinci_spi->base + SPIDEF); > > - if (davinci_spi->pdata->intr_level) > - iowrite32(SPI_INTLVL_1, davinci_spi->base + SPILVL); > - else > - iowrite32(SPI_INTLVL_0, davinci_spi->base + SPILVL); > + set_io_bits(davinci_spi->base + SPIGCR1, SPIGCR1_CLKMOD_MASK); > + set_io_bits(davinci_spi->base + SPIGCR1, SPIGCR1_MASTER_MASK); > + set_io_bits(davinci_spi->base + SPIGCR1, SPIGCR1_POWERDOWN_MASK); > > ret = spi_bitbang_start(&davinci_spi->bitbang); > - if (ret) > + if (ret != 0) > goto free_clk; > > dev_info(&pdev->dev, "Controller at 0x%p \n", davinci_spi->base); > > - if (!pdata->poll_mode) > - dev_info(&pdev->dev, "Operating in interrupt mode" > - " using IRQ %d\n", davinci_spi->irq); > - > return ret; > > free_clk: > @@ -1199,7 +1042,7 @@ put_master: > spi_master_put(master); > free_tmp_buf: > kfree(davinci_spi->tmp_buf); > -irq_free: > +err1: > free_irq(davinci_spi->irq, davinci_spi); > unmap_io: > iounmap(davinci_spi->base); > @@ -1211,7 +1054,7 @@ err: > return ret; > } > > -/** > +/* > * davinci_spi_remove - remove function for SPI Master Controller > * @pdev: platform_device structure which contains plateform specific data > * > @@ -1220,7 +1063,7 @@ err: > * It will also call spi_bitbang_stop to destroy the work queue which was > * created by spi_bitbang_start. > */ > -static int __exit davinci_spi_remove(struct platform_device *pdev) > +static int __devexit davinci_spi_remove(struct platform_device *pdev) > { > struct davinci_spi *davinci_spi; > struct spi_master *master; > @@ -1242,8 +1085,11 @@ static int __exit davinci_spi_remove(struct platform_device *pdev) > } > > static struct platform_driver davinci_spi_driver = { > - .driver.name = "spi_davinci", > - .remove = __exit_p(davinci_spi_remove), > + .driver = { > + .name = "spi_davinci", > + .owner = THIS_MODULE, > + }, > + .remove = __devexit_p(davinci_spi_remove), > }; > > static int __init davinci_spi_init(void) > -- > 1.6.3.3 > > -- Grant Likely, B.Sc., P.Eng. Secret Lab Technologies Ltd. ------------------------------------------------------------------------------ This SF.net email is sponsored by Sprint What will you do first with EVO, the first 4G phone? Visit sprint.com/first -- http://p.sf.net/sfu/sprint-com-first ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v2 0/1] davinci: spi: replace existing driver [not found] ` <1278110334-13943-1-git-send-email-bniebuhr-JaPwekKOx1yaMJb+Lgu22Q@public.gmane.org> 2010-07-02 22:38 ` [PATCH v2 1/1] " Brian Niebuhr @ 2010-07-06 8:36 ` Sudhakar Rajashekhara 2010-07-06 8:36 ` Sudhakar Rajashekhara 2 siblings, 0 replies; 12+ messages in thread From: Sudhakar Rajashekhara @ 2010-07-06 8:36 UTC (permalink / raw) To: 'Brian Niebuhr', spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f Cc: davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/ Hi, On Sat, Jul 03, 2010 at 04:08:53, Brian Niebuhr wrote: > I have included all of the recommended changes in this version of the patch. > I also combined the patches into one patch to avoid bisecting issues. This > makes the diff on davinci_spi.c very large. > > If people who are using this driver could test this version of the driver > and Ack it, I would appreciate it. > > ** NOTE ** > > This patch requires the EDMA patch at: > > http://linux.davincidsp.com/pipermail/davinci-linux-open-source/2010-March/018022.html > > which is queued waiting on another driver fix, for DMA mode to work correctly. > > > Brian Niebuhr (1): > davinci: spi: replace existing driver > > arch/arm/mach-davinci/board-dm355-evm.c | 10 + > arch/arm/mach-davinci/board-dm355-leopard.c | 10 + > arch/arm/mach-davinci/board-dm365-evm.c | 10 + > arch/arm/mach-davinci/dm355.c | 12 +- > arch/arm/mach-davinci/dm365.c | 12 +- > arch/arm/mach-davinci/include/mach/spi.h | 37 +- > drivers/spi/davinci_spi.c | 1328 ++++++++++++--------------- > 7 files changed, 648 insertions(+), 771 deletions(-) > Quick update. I tested this patch on DM355 and DM365 EVMs. On DM355 all the 3 modes (DMA, Polled and Interrupt) worked fine. But in interrupt mode, on DM355, if I set "intr_level = 1", then kernel hangs during booting after printing "spi spi0.0: DaVinci SPI driver in Interrupt mode" on the console. On DM365 only DMA and Polled mode worked fine. In interrupt mode, whether I set intr_level to ZERO or ONE, kernel booting hangs, similar to DM355. I'll update the status of testing on OMAP-L1x EVMs later. I am using the Linux kernel from [1] for testing. [1] http://git.kernel.org/?p=linux/kernel/git/khilman/linux-davinci.git;a=summary Regards, Sudhakar ------------------------------------------------------------------------------ This SF.net email is sponsored by Sprint What will you do first with EVO, the first 4G phone? Visit sprint.com/first -- http://p.sf.net/sfu/sprint-com-first ^ permalink raw reply [flat|nested] 12+ messages in thread
* RE: [PATCH v2 0/1] davinci: spi: replace existing driver [not found] ` <1278110334-13943-1-git-send-email-bniebuhr-JaPwekKOx1yaMJb+Lgu22Q@public.gmane.org> 2010-07-02 22:38 ` [PATCH v2 1/1] " Brian Niebuhr 2010-07-06 8:36 ` [PATCH v2 0/1] " Sudhakar Rajashekhara @ 2010-07-06 8:36 ` Sudhakar Rajashekhara 2 siblings, 0 replies; 12+ messages in thread From: Sudhakar Rajashekhara @ 2010-07-06 8:36 UTC (permalink / raw) To: 'Brian Niebuhr', spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f Cc: grant.likely-s3s/WqlpOiPyB63q8FvJNQ, davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/ Hi, On Sat, Jul 03, 2010 at 04:08:53, Brian Niebuhr wrote: > I have included all of the recommended changes in this version of the patch. > I also combined the patches into one patch to avoid bisecting issues. This > makes the diff on davinci_spi.c very large. > > If people who are using this driver could test this version of the driver > and Ack it, I would appreciate it. > > ** NOTE ** > > This patch requires the EDMA patch at: > > http://linux.davincidsp.com/pipermail/davinci-linux-open-source/2010-March/018022.html > > which is queued waiting on another driver fix, for DMA mode to work correctly. > > > Brian Niebuhr (1): > davinci: spi: replace existing driver > > arch/arm/mach-davinci/board-dm355-evm.c | 10 + > arch/arm/mach-davinci/board-dm355-leopard.c | 10 + > arch/arm/mach-davinci/board-dm365-evm.c | 10 + > arch/arm/mach-davinci/dm355.c | 12 +- > arch/arm/mach-davinci/dm365.c | 12 +- > arch/arm/mach-davinci/include/mach/spi.h | 37 +- > drivers/spi/davinci_spi.c | 1328 ++++++++++++--------------- > 7 files changed, 648 insertions(+), 771 deletions(-) > Quick update. I tested this patch on DM355 and DM365 EVMs. On DM355 all the 3 modes (DMA, Polled and Interrupt) worked fine. But in interrupt mode, on DM355, if I set "intr_level = 1", then kernel hangs during booting after printing "spi spi0.0: DaVinci SPI driver in Interrupt mode" on the console. On DM365 only DMA and Polled mode worked fine. In interrupt mode, whether I set intr_level to ZERO or ONE, kernel booting hangs, similar to DM355. I'll update the status of testing on OMAP-L1x EVMs later. I am using the Linux kernel from [1] for testing. [1] http://git.kernel.org/?p=linux/kernel/git/khilman/linux-davinci.git;a=summary Regards, Sudhakar ^ permalink raw reply [flat|nested] 12+ messages in thread
[parent not found: <002301cb1ce6$64fba3e0$2ef2eba0$@raj@ti.com>]
[parent not found: <002301cb1ce6$64fba3e0$2ef2eba0$@raj-l0cyMroinI0@public.gmane.org>]
* Re: [PATCH v2 0/1] davinci: spi: replaceexisting driver [not found] ` <002301cb1ce6$64fba3e0$2ef2eba0$@raj-l0cyMroinI0@public.gmane.org> @ 2010-07-06 14:15 ` Brian Niebuhr [not found] ` <BA34378D1528D04CB3C865B8BAB2472B035F78-mqUZVEcnZosHtCCSzi1I5PfQPhDVBs+grNQQ6b5fDX0@public.gmane.org> [not found] ` <013901cb1dc6$747ab500$5d701f00$@raj@ti.com> 0 siblings, 2 replies; 12+ messages in thread From: Brian Niebuhr @ 2010-07-06 14:15 UTC (permalink / raw) To: Sudhakar Rajashekhara, Brian Niebuhr, spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f Cc: davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/ > On Sat, Jul 03, 2010 at 04:08:53, Brian Niebuhr wrote: > > I have included all of the recommended changes in this > version of the patch. > > I also combined the patches into one patch to avoid > bisecting issues. This > > makes the diff on davinci_spi.c very large. > > > > If people who are using this driver could test this version > of the driver > > and Ack it, I would appreciate it. > > > > ** NOTE ** > > > > This patch requires the EDMA patch at: > > > > > http://linux.davincidsp.com/pipermail/davinci-linux-open-sourc > e/2010-March/018022.html > > > > which is queued waiting on another driver fix, for DMA mode > to work correctly. > > > > > > Brian Niebuhr (1): > > davinci: spi: replace existing driver > > > > arch/arm/mach-davinci/board-dm355-evm.c | 10 + > > arch/arm/mach-davinci/board-dm355-leopard.c | 10 + > > arch/arm/mach-davinci/board-dm365-evm.c | 10 + > > arch/arm/mach-davinci/dm355.c | 12 +- > > arch/arm/mach-davinci/dm365.c | 12 +- > > arch/arm/mach-davinci/include/mach/spi.h | 37 +- > > drivers/spi/davinci_spi.c | 1328 > ++++++++++++--------------- > > 7 files changed, 648 insertions(+), 771 deletions(-) > > > > Quick update. > > I tested this patch on DM355 and DM365 EVMs. On DM355 all the > 3 modes (DMA, > Polled and Interrupt) worked fine. But in interrupt mode, on > DM355, if I set > "intr_level = 1", then kernel hangs during booting after printing > "spi spi0.0: DaVinci SPI driver in Interrupt mode" on the console. Sudhakar - When you changed the interrupt level, did you also change the IORESOURCE_IRQ entry for SPI0? Maybe we could set the interrupt level automatically based on the IORESOURCE_IRQ provided? The problem is, I don't see any way of doing that without a bunch of machine-specific ifdefs in the driver. > On DM365 only DMA and Polled mode worked fine. In interrupt > mode, whether I > set intr_level to ZERO or ONE, kernel booting hangs, similar to DM355. Does the interrupt mode of the existing driver work on DM365? I don't have one of these boards, so I can't debug the issue. If you have any ideas where the problem might be I'd appreciate the help in getting this resolved. If the change I mentioned above fixes the issue on DM355, then I've got to imagine that it's just a configuration issue of some sort on DM365. > I'll update the status of testing on OMAP-L1x EVMs later. > > I am using the Linux kernel from [1] for testing. > > [1] > http://git.kernel.org/?p=linux/kernel/git/khilman/linux-davinc > i.git;a=summary ------------------------------------------------------------------------------ This SF.net email is sponsored by Sprint What will you do first with EVO, the first 4G phone? Visit sprint.com/first -- http://p.sf.net/sfu/sprint-com-first ^ permalink raw reply [flat|nested] 12+ messages in thread
[parent not found: <BA34378D1528D04CB3C865B8BAB2472B035F78-mqUZVEcnZosHtCCSzi1I5PfQPhDVBs+grNQQ6b5fDX0@public.gmane.org>]
* Re: [PATCH v2 0/1] davinci: spi: replaceexisting driver [not found] ` <BA34378D1528D04CB3C865B8BAB2472B035F78-mqUZVEcnZosHtCCSzi1I5PfQPhDVBs+grNQQ6b5fDX0@public.gmane.org> @ 2010-07-07 11:20 ` Sudhakar Rajashekhara 2010-07-07 11:20 ` [spi-devel-general] " Sudhakar Rajashekhara 1 sibling, 0 replies; 12+ messages in thread From: Sudhakar Rajashekhara @ 2010-07-07 11:20 UTC (permalink / raw) To: 'Brian Niebuhr', 'Brian Niebuhr', spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f Cc: davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/ Hi Brian, On Tue, Jul 06, 2010 at 19:45:56, Brian Niebuhr wrote: > > On Sat, Jul 03, 2010 at 04:08:53, Brian Niebuhr wrote: > > > I have included all of the recommended changes in this [...] > > > > Quick update. > > > > I tested this patch on DM355 and DM365 EVMs. On DM355 all the > > 3 modes (DMA, > > Polled and Interrupt) worked fine. But in interrupt mode, on > > DM355, if I set > > "intr_level = 1", then kernel hangs during booting after printing > > "spi spi0.0: DaVinci SPI driver in Interrupt mode" on the console. > > Sudhakar - > > When you changed the interrupt level, did you also change the > IORESOURCE_IRQ entry for SPI0? Maybe we could set the interrupt level > automatically based on the IORESOURCE_IRQ provided? IORESOURCE_IRQ entry for dm365 were already present in dm365.c. > > > On DM365 only DMA and Polled mode worked fine. In interrupt > > mode, whether I > > set intr_level to ZERO or ONE, kernel booting hangs, similar to DM355. > > Does the interrupt mode of the existing driver work on DM365? > AFAIK, support for interrupt mode was not present in the earlier driver by Sandeep Paulraj. > I don't have one of these boards, so I can't debug the issue. If you > have any ideas where the problem might be I'd appreciate the help in > getting this resolved. As I mentioned in my earlier e-mail, on DM365 kernel booting hangs after Printing "spi spi0.0: DaVinci SPI driver in Interrupt mode" on the console. Control is in spi_sync() function waiting for completion. > If the change I mentioned above fixes the issue on DM355, then I am not sure whether my earlier mail was clear in this regard or not but interrupt mode works fine on DM355 if intr_level = 0. Kernel booting hangs on DM355 if intr_level = 1. > I've got to imagine that it's just a configuration issue > of some sort on DM365. > I am also of the same opinion. Thanks, Sudhakar ------------------------------------------------------------------------------ This SF.net email is sponsored by Sprint What will you do first with EVO, the first 4G phone? Visit sprint.com/first -- http://p.sf.net/sfu/sprint-com-first ^ permalink raw reply [flat|nested] 12+ messages in thread
* RE: [spi-devel-general] [PATCH v2 0/1] davinci: spi: replaceexisting driver [not found] ` <BA34378D1528D04CB3C865B8BAB2472B035F78-mqUZVEcnZosHtCCSzi1I5PfQPhDVBs+grNQQ6b5fDX0@public.gmane.org> 2010-07-07 11:20 ` Sudhakar Rajashekhara @ 2010-07-07 11:20 ` Sudhakar Rajashekhara 1 sibling, 0 replies; 12+ messages in thread From: Sudhakar Rajashekhara @ 2010-07-07 11:20 UTC (permalink / raw) To: 'Brian Niebuhr', 'Brian Niebuhr', spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f Cc: davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/ Hi Brian, On Tue, Jul 06, 2010 at 19:45:56, Brian Niebuhr wrote: > > On Sat, Jul 03, 2010 at 04:08:53, Brian Niebuhr wrote: > > > I have included all of the recommended changes in this [...] > > > > Quick update. > > > > I tested this patch on DM355 and DM365 EVMs. On DM355 all the > > 3 modes (DMA, > > Polled and Interrupt) worked fine. But in interrupt mode, on > > DM355, if I set > > "intr_level = 1", then kernel hangs during booting after printing > > "spi spi0.0: DaVinci SPI driver in Interrupt mode" on the console. > > Sudhakar - > > When you changed the interrupt level, did you also change the > IORESOURCE_IRQ entry for SPI0? Maybe we could set the interrupt level > automatically based on the IORESOURCE_IRQ provided? IORESOURCE_IRQ entry for dm365 were already present in dm365.c. > > > On DM365 only DMA and Polled mode worked fine. In interrupt > > mode, whether I > > set intr_level to ZERO or ONE, kernel booting hangs, similar to DM355. > > Does the interrupt mode of the existing driver work on DM365? > AFAIK, support for interrupt mode was not present in the earlier driver by Sandeep Paulraj. > I don't have one of these boards, so I can't debug the issue. If you > have any ideas where the problem might be I'd appreciate the help in > getting this resolved. As I mentioned in my earlier e-mail, on DM365 kernel booting hangs after Printing "spi spi0.0: DaVinci SPI driver in Interrupt mode" on the console. Control is in spi_sync() function waiting for completion. > If the change I mentioned above fixes the issue on DM355, then I am not sure whether my earlier mail was clear in this regard or not but interrupt mode works fine on DM355 if intr_level = 0. Kernel booting hangs on DM355 if intr_level = 1. > I've got to imagine that it's just a configuration issue > of some sort on DM365. > I am also of the same opinion. Thanks, Sudhakar ^ permalink raw reply [flat|nested] 12+ messages in thread
[parent not found: <013901cb1dc6$747ab500$5d701f00$@raj@ti.com>]
[parent not found: <013901cb1dc6$747ab500$5d701f00$@raj-l0cyMroinI0@public.gmane.org>]
* Re: [PATCH v2 0/1] davinci: spi: replaceexisting driver [not found] ` <013901cb1dc6$747ab500$5d701f00$@raj-l0cyMroinI0@public.gmane.org> @ 2010-07-07 13:16 ` Paulraj, Sandeep 2010-07-07 17:02 ` [PATCH v2 0/1] davinci: spi:replaceexisting driver Brian Niebuhr 1 sibling, 0 replies; 12+ messages in thread From: Paulraj, Sandeep @ 2010-07-07 13:16 UTC (permalink / raw) To: Rajashekhara, Sudhakar, 'Brian Niebuhr', 'Brian Niebuhr', "spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org" <spi-dev Cc: davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/@public.gmane.org > > > > Does the interrupt mode of the existing driver work on DM365? > > > > AFAIK, support for interrupt mode was not present in the earlier driver > by Sandeep Paulraj. > All three modes had worked fine on multiple TI SOC's including DM355 and DM365 when I had submitted the driver. Sandeep ------------------------------------------------------------------------------ This SF.net email is sponsored by Sprint What will you do first with EVO, the first 4G phone? Visit sprint.com/first -- http://p.sf.net/sfu/sprint-com-first ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v2 0/1] davinci: spi:replaceexisting driver [not found] ` <013901cb1dc6$747ab500$5d701f00$@raj-l0cyMroinI0@public.gmane.org> 2010-07-07 13:16 ` Paulraj, Sandeep @ 2010-07-07 17:02 ` Brian Niebuhr [not found] ` <BA34378D1528D04CB3C865B8BAB2472B035FCD-mqUZVEcnZosHtCCSzi1I5PfQPhDVBs+grNQQ6b5fDX0@public.gmane.org> 1 sibling, 1 reply; 12+ messages in thread From: Brian Niebuhr @ 2010-07-07 17:02 UTC (permalink / raw) To: Sudhakar Rajashekhara, Brian Niebuhr, spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f Cc: davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/ > -----Original Message----- > From: Sudhakar Rajashekhara [mailto:sudhakar.raj-l0cyMroinI0@public.gmane.org] > Sent: Wednesday, July 07, 2010 6:21 AM > To: Brian Niebuhr; 'Brian Niebuhr'; > spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org > Cc: davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/@public.gmane.org > Subject: Re: [spi-devel-general] [PATCH v2 0/1] davinci: > spi:replaceexisting driver > > Hi Brian, > > On Tue, Jul 06, 2010 at 19:45:56, Brian Niebuhr wrote: > > > On Sat, Jul 03, 2010 at 04:08:53, Brian Niebuhr wrote: > > > > I have included all of the recommended changes in this > > [...] > > > > > > > Quick update. > > > > > > I tested this patch on DM355 and DM365 EVMs. On DM355 all the > > > 3 modes (DMA, > > > Polled and Interrupt) worked fine. But in interrupt mode, on > > > DM355, if I set > > > "intr_level = 1", then kernel hangs during booting after printing > > > "spi spi0.0: DaVinci SPI driver in Interrupt mode" on the console. > > > > Sudhakar - > > > > When you changed the interrupt level, did you also change the > > IORESOURCE_IRQ entry for SPI0? Maybe we could set the > interrupt level > > automatically based on the IORESOURCE_IRQ provided? > > IORESOURCE_IRQ entry for dm365 were already present in dm365.c. I should have been more clear: The intr_level setting chooses which IRQ is used to signal events. If you change intr_level to 1 then you also need to change the IRQ that is provided as a resource to the driver to match. On DM355 intr_level=0 corresponds to SPINT0_0 (42) and intr_level=1 corresponds to SPINT0_1 (43). > > > > > On DM365 only DMA and Polled mode worked fine. In interrupt > > > mode, whether I > > > set intr_level to ZERO or ONE, kernel booting hangs, > similar to DM355. > > > > Does the interrupt mode of the existing driver work on DM365? > > > > AFAIK, support for interrupt mode was not present in the > earlier driver > by Sandeep Paulraj. > > > I don't have one of these boards, so I can't debug the > issue. If you > > have any ideas where the problem might be I'd appreciate the help in > > getting this resolved. > > As I mentioned in my earlier e-mail, on DM365 kernel booting > hangs after > Printing "spi spi0.0: DaVinci SPI driver in Interrupt mode" > on the console. > Control is in spi_sync() function waiting for completion. I've got an idea what the problem is: When I was writing the driver I was looking at the DM355 for as an example of the "version 1" SPI controller. The DM355 doesn't have a TX interrupt, so I thought that was a feature of the "version 1" controller. However, DM365 does have a TX interrupt, even though it has a "version 1" controller. The interrupt handler in the driver changes its processing based on whether it is a "version 1" or "version 2" device, but obviously that's not quite correct. Could you try one experiment for me on the DM365 board? Could you change SPIINT_MASKINT to 0x0000015Fu and retest on the DM365 only? This should make it behave like the DM355. If that fixes the problem, then at least I know where the problem is. I don't have a good idea how to solve it yet, though. > > If the change I mentioned above fixes the issue on DM355, then > > I am not sure whether my earlier mail was clear in this regard or not > but interrupt mode works fine on DM355 if intr_level = 0. > Kernel booting > hangs on DM355 if intr_level = 1. > > > I've got to imagine that it's just a configuration issue > > of some sort on DM365. > > > > I am also of the same opinion. > > Thanks, > Sudhakar > > > > -------------------------------------------------------------- > ---------------- > This SF.net email is sponsored by Sprint > What will you do first with EVO, the first 4G phone? > Visit sprint.com/first -- http://p.sf.net/sfu/sprint-com-first > _______________________________________________ > spi-devel-general mailing list > spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org > https://lists.sourceforge.net/lists/listinfo/spi-devel-general > > ------------------------------------------------------------------------------ This SF.net email is sponsored by Sprint What will you do first with EVO, the first 4G phone? Visit sprint.com/first -- http://p.sf.net/sfu/sprint-com-first ^ permalink raw reply [flat|nested] 12+ messages in thread
[parent not found: <BA34378D1528D04CB3C865B8BAB2472B035FCD-mqUZVEcnZosHtCCSzi1I5PfQPhDVBs+grNQQ6b5fDX0@public.gmane.org>]
* Re: [PATCH v2 0/1] davinci: spi:replaceexisting driver [not found] ` <BA34378D1528D04CB3C865B8BAB2472B035FCD-mqUZVEcnZosHtCCSzi1I5PfQPhDVBs+grNQQ6b5fDX0@public.gmane.org> @ 2010-07-08 3:49 ` Sudhakar Rajashekhara 2010-07-08 3:49 ` [spi-devel-general] " Sudhakar Rajashekhara 1 sibling, 0 replies; 12+ messages in thread From: Sudhakar Rajashekhara @ 2010-07-08 3:49 UTC (permalink / raw) To: 'Brian Niebuhr', 'Brian Niebuhr', spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f Cc: davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/ Hi, On Wed, Jul 07, 2010 at 22:32:58, Brian Niebuhr wrote: > > -----Original Message----- > > From: Sudhakar Rajashekhara [mailto:sudhakar.raj-l0cyMroinI0@public.gmane.org] > > Sent: Wednesday, July 07, 2010 6:21 AM > > To: Brian Niebuhr; 'Brian Niebuhr'; > > spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org > > Cc: davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/@public.gmane.org > > Subject: Re: [spi-devel-general] [PATCH v2 0/1] davinci: > > spi:replaceexisting driver > > > > Hi Brian, > > > > On Tue, Jul 06, 2010 at 19:45:56, Brian Niebuhr wrote: > > > > On Sat, Jul 03, 2010 at 04:08:53, Brian Niebuhr wrote: > > > > > I have included all of the recommended changes in this > > > > [...] > > > > > > > > > > Quick update. > > > > > > > > I tested this patch on DM355 and DM365 EVMs. On DM355 all the > > > > 3 modes (DMA, > > > > Polled and Interrupt) worked fine. But in interrupt mode, on > > > > DM355, if I set > > > > "intr_level = 1", then kernel hangs during booting after printing > > > > "spi spi0.0: DaVinci SPI driver in Interrupt mode" on the console. > > > > > > Sudhakar - > > > > > > When you changed the interrupt level, did you also change the > > > IORESOURCE_IRQ entry for SPI0? Maybe we could set the > > interrupt level > > > automatically based on the IORESOURCE_IRQ provided? > > > > IORESOURCE_IRQ entry for dm365 were already present in dm365.c. > > > I should have been more clear: The intr_level setting chooses which IRQ > is used to signal events. If you change intr_level to 1 then you also > need to change the IRQ that is provided as a resource to the driver to > match. On DM355 intr_level=0 corresponds to SPINT0_0 (42) and > intr_level=1 corresponds to SPINT0_1 (43). > > > > > > > > > On DM365 only DMA and Polled mode worked fine. In interrupt > > > > mode, whether I > > > > set intr_level to ZERO or ONE, kernel booting hangs, > > similar to DM355. > > > > > > Does the interrupt mode of the existing driver work on DM365? > > > > > > > AFAIK, support for interrupt mode was not present in the > > earlier driver > > by Sandeep Paulraj. > > > > > I don't have one of these boards, so I can't debug the > > issue. If you > > > have any ideas where the problem might be I'd appreciate the help in > > > getting this resolved. > > > > As I mentioned in my earlier e-mail, on DM365 kernel booting > > hangs after > > Printing "spi spi0.0: DaVinci SPI driver in Interrupt mode" > > on the console. > > Control is in spi_sync() function waiting for completion. > > > I've got an idea what the problem is: When I was writing the driver I > was looking at the DM355 for as an example of the "version 1" SPI > controller. The DM355 doesn't have a TX interrupt, so I thought that > was a feature of the "version 1" controller. However, DM365 does have a > TX interrupt, even though it has a "version 1" controller. The > interrupt handler in the driver changes its processing based on whether > it is a "version 1" or "version 2" device, but obviously that's not > quite correct. > > Could you try one experiment for me on the DM365 board? Could you > change SPIINT_MASKINT to 0x0000015Fu and retest on the DM365 only? This > should make it behave like the DM355. If that fixes the problem, then > at least I know where the problem is. I don't have a good idea how to > solve it yet, though. > Bingo. With the modification you suggested above, interrupt mode worked fine on DM365. Thanks, Sudhakar ------------------------------------------------------------------------------ This SF.net email is sponsored by Sprint What will you do first with EVO, the first 4G phone? Visit sprint.com/first -- http://p.sf.net/sfu/sprint-com-first ^ permalink raw reply [flat|nested] 12+ messages in thread
* RE: [spi-devel-general] [PATCH v2 0/1] davinci: spi:replaceexisting driver [not found] ` <BA34378D1528D04CB3C865B8BAB2472B035FCD-mqUZVEcnZosHtCCSzi1I5PfQPhDVBs+grNQQ6b5fDX0@public.gmane.org> 2010-07-08 3:49 ` Sudhakar Rajashekhara @ 2010-07-08 3:49 ` Sudhakar Rajashekhara 1 sibling, 0 replies; 12+ messages in thread From: Sudhakar Rajashekhara @ 2010-07-08 3:49 UTC (permalink / raw) To: 'Brian Niebuhr', 'Brian Niebuhr', spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f Cc: davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/ Hi, On Wed, Jul 07, 2010 at 22:32:58, Brian Niebuhr wrote: > > -----Original Message----- > > From: Sudhakar Rajashekhara [mailto:sudhakar.raj-l0cyMroinI0@public.gmane.org] > > Sent: Wednesday, July 07, 2010 6:21 AM > > To: Brian Niebuhr; 'Brian Niebuhr'; > > spi-devel-general-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org > > Cc: davinci-linux-open-source-VycZQUHpC/PFrsHnngEfi1aTQe2KTcn/@public.gmane.org > > Subject: Re: [spi-devel-general] [PATCH v2 0/1] davinci: > > spi:replaceexisting driver > > > > Hi Brian, > > > > On Tue, Jul 06, 2010 at 19:45:56, Brian Niebuhr wrote: > > > > On Sat, Jul 03, 2010 at 04:08:53, Brian Niebuhr wrote: > > > > > I have included all of the recommended changes in this > > > > [...] > > > > > > > > > > Quick update. > > > > > > > > I tested this patch on DM355 and DM365 EVMs. On DM355 all the > > > > 3 modes (DMA, > > > > Polled and Interrupt) worked fine. But in interrupt mode, on > > > > DM355, if I set > > > > "intr_level = 1", then kernel hangs during booting after printing > > > > "spi spi0.0: DaVinci SPI driver in Interrupt mode" on the console. > > > > > > Sudhakar - > > > > > > When you changed the interrupt level, did you also change the > > > IORESOURCE_IRQ entry for SPI0? Maybe we could set the > > interrupt level > > > automatically based on the IORESOURCE_IRQ provided? > > > > IORESOURCE_IRQ entry for dm365 were already present in dm365.c. > > > I should have been more clear: The intr_level setting chooses which IRQ > is used to signal events. If you change intr_level to 1 then you also > need to change the IRQ that is provided as a resource to the driver to > match. On DM355 intr_level=0 corresponds to SPINT0_0 (42) and > intr_level=1 corresponds to SPINT0_1 (43). > > > > > > > > > On DM365 only DMA and Polled mode worked fine. In interrupt > > > > mode, whether I > > > > set intr_level to ZERO or ONE, kernel booting hangs, > > similar to DM355. > > > > > > Does the interrupt mode of the existing driver work on DM365? > > > > > > > AFAIK, support for interrupt mode was not present in the > > earlier driver > > by Sandeep Paulraj. > > > > > I don't have one of these boards, so I can't debug the > > issue. If you > > > have any ideas where the problem might be I'd appreciate the help in > > > getting this resolved. > > > > As I mentioned in my earlier e-mail, on DM365 kernel booting > > hangs after > > Printing "spi spi0.0: DaVinci SPI driver in Interrupt mode" > > on the console. > > Control is in spi_sync() function waiting for completion. > > > I've got an idea what the problem is: When I was writing the driver I > was looking at the DM355 for as an example of the "version 1" SPI > controller. The DM355 doesn't have a TX interrupt, so I thought that > was a feature of the "version 1" controller. However, DM365 does have a > TX interrupt, even though it has a "version 1" controller. The > interrupt handler in the driver changes its processing based on whether > it is a "version 1" or "version 2" device, but obviously that's not > quite correct. > > Could you try one experiment for me on the DM365 board? Could you > change SPIINT_MASKINT to 0x0000015Fu and retest on the DM365 only? This > should make it behave like the DM355. If that fixes the problem, then > at least I know where the problem is. I don't have a good idea how to > solve it yet, though. > Bingo. With the modification you suggested above, interrupt mode worked fine on DM365. Thanks, Sudhakar ^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2010-07-08 3:49 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2010-07-02 22:38 [PATCH v2 0/1] davinci: spi: replace existing driver Brian Niebuhr
[not found] ` <1278110334-13943-1-git-send-email-bniebuhr-JaPwekKOx1yaMJb+Lgu22Q@public.gmane.org>
2010-07-02 22:38 ` [PATCH v2 1/1] " Brian Niebuhr
[not found] ` <1278110334-13943-2-git-send-email-bniebuhr-JaPwekKOx1yaMJb+Lgu22Q@public.gmane.org>
2010-07-04 5:47 ` Grant Likely
2010-07-06 8:36 ` [PATCH v2 0/1] " Sudhakar Rajashekhara
2010-07-06 8:36 ` Sudhakar Rajashekhara
[not found] ` <002301cb1ce6$64fba3e0$2ef2eba0$@raj@ti.com>
[not found] ` <002301cb1ce6$64fba3e0$2ef2eba0$@raj-l0cyMroinI0@public.gmane.org>
2010-07-06 14:15 ` [PATCH v2 0/1] davinci: spi: replaceexisting driver Brian Niebuhr
[not found] ` <BA34378D1528D04CB3C865B8BAB2472B035F78-mqUZVEcnZosHtCCSzi1I5PfQPhDVBs+grNQQ6b5fDX0@public.gmane.org>
2010-07-07 11:20 ` Sudhakar Rajashekhara
2010-07-07 11:20 ` [spi-devel-general] " Sudhakar Rajashekhara
[not found] ` <013901cb1dc6$747ab500$5d701f00$@raj@ti.com>
[not found] ` <013901cb1dc6$747ab500$5d701f00$@raj-l0cyMroinI0@public.gmane.org>
2010-07-07 13:16 ` Paulraj, Sandeep
2010-07-07 17:02 ` [PATCH v2 0/1] davinci: spi:replaceexisting driver Brian Niebuhr
[not found] ` <BA34378D1528D04CB3C865B8BAB2472B035FCD-mqUZVEcnZosHtCCSzi1I5PfQPhDVBs+grNQQ6b5fDX0@public.gmane.org>
2010-07-08 3:49 ` Sudhakar Rajashekhara
2010-07-08 3:49 ` [spi-devel-general] " Sudhakar Rajashekhara
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).