[PATCH v3 1/2] spi: dt-bindings: qcom,spi-geni-qcom: convert to dtschema

[PATCH v3 1/2] spi: dt-bindings: qcom,spi-geni-qcom: convert to dtschema

[Krzysztof Kozlowski]

Convert the GENI based Qualcomm Universal Peripheral (QUP) Serial
Peripheral Interface (SPI) bindings to DT Schema.

The original bindings in TXT were not complete, so add during conversion
properties already used in DTS and/or in the driver: dmas,
interconnects, operating points and power-domains.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

---

Changes since v2:
1. Drop reg-names.

Changes since v1:
1. Correct $ref path and remove interconnect minItems (Kuldeep).
2. Remove child tpm device from example.
3. Pad reg hex addresses with 00.
---
 .../bindings/spi/qcom,spi-geni-qcom.txt       |  39 ------
 .../bindings/spi/qcom,spi-geni-qcom.yaml      | 116 ++++++++++++++++++
 2 files changed, 116 insertions(+), 39 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt
 create mode 100644 Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.yaml

diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt b/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt
deleted file mode 100644
index c8c1e913f4e7..000000000000
--- a/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt
+++ /dev/null
@@ -1,39 +0,0 @@
-GENI based Qualcomm Universal Peripheral (QUP) Serial Peripheral Interface (SPI)
-
-The QUP v3 core is a GENI based AHB slave that provides a common data path
-(an output FIFO and an input FIFO) for serial peripheral interface (SPI)
-mini-core.
-
-SPI in master mode supports up to 50MHz, up to four chip selects, programmable
-data path from 4 bits to 32 bits and numerous protocol variants.
-
-Required properties:
-- compatible:		Must contain "qcom,geni-spi".
-- reg:			Must contain SPI register location and length.
-- interrupts:		Must contain SPI controller interrupts.
-- clock-names:		Must contain "se".
-- clocks:		Serial engine core clock needed by the device.
-- #address-cells:	Must be <1> to define a chip select address on
-			the SPI bus.
-- #size-cells:		Must be <0>.
-
-SPI Controller nodes must be child of GENI based Qualcomm Universal
-Peripharal. Please refer GENI based QUP wrapper controller node bindings
-described in Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.yaml.
-
-SPI slave nodes must be children of the SPI master node and conform to SPI bus
-binding as described in Documentation/devicetree/bindings/spi/spi-bus.txt.
-
-Example:
-	spi0: spi@a84000 {
-		compatible = "qcom,geni-spi";
-		reg = <0xa84000 0x4000>;
-		interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
-		clock-names = "se";
-		clocks = <&clock_gcc GCC_QUPV3_WRAP0_S0_CLK>;
-		pinctrl-names = "default", "sleep";
-		pinctrl-0 = <&qup_1_spi_2_active>;
-		pinctrl-1 = <&qup_1_spi_2_sleep>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-	};
diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.yaml b/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.yaml
new file mode 100644
index 000000000000..e2c7b934c50d
--- /dev/null
+++ b/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.yaml
@@ -0,0 +1,116 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/qcom,spi-geni-qcom.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: GENI based Qualcomm Universal Peripheral (QUP) Serial Peripheral Interface (SPI)
+
+maintainers:
+  - Andy Gross <agross@kernel.org>
+  - Bjorn Andersson <bjorn.andersson@linaro.org>
+  - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
+
+description:
+  The QUP v3 core is a GENI based AHB slave that provides a common data path
+  (an output FIFO and an input FIFO) for serial peripheral interface (SPI)
+  mini-core.
+
+  SPI in master mode supports up to 50MHz, up to four chip selects,
+  programmable data path from 4 bits to 32 bits and numerous protocol variants.
+
+  SPI Controller nodes must be child of GENI based Qualcomm Universal
+  Peripharal. Please refer GENI based QUP wrapper controller node bindings
+  described in Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.yaml.
+
+allOf:
+  - $ref: /schemas/spi/spi-controller.yaml#
+
+properties:
+  compatible:
+    const: qcom,geni-spi
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    const: se
+
+  dmas:
+    maxItems: 2
+
+  dma-names:
+    items:
+      - const: tx
+      - const: rx
+
+  interconnects:
+    maxItems: 2
+
+  interconnect-names:
+    items:
+      - const: qup-core
+      - const: qup-config
+
+  interrupts:
+    maxItems: 1
+
+  operating-points-v2: true
+
+  power-domains:
+    maxItems: 1
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - clocks
+  - clock-names
+  - interrupts
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,gcc-sc7180.h>
+    #include <dt-bindings/interconnect/qcom,sc7180.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/power/qcom-rpmpd.h>
+
+    spi@880000 {
+        compatible = "qcom,geni-spi";
+        reg = <0x00880000 0x4000>;
+        clock-names = "se";
+        clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+        pinctrl-names = "default";
+        pinctrl-0 = <&qup_spi0_default>;
+        interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+        power-domains = <&rpmhpd SC7180_CX>;
+        operating-points-v2 = <&qup_opp_table>;
+        interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
+                        <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>;
+        interconnect-names = "qup-core", "qup-config";
+    };
+
+  - |
+    #include <dt-bindings/dma/qcom-gpi.h>
+
+    spi@884000 {
+        compatible = "qcom,geni-spi";
+        reg = <0x00884000 0x4000>;
+        clock-names = "se";
+        clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+        dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
+               <&gpi_dma0 1 1 QCOM_GPI_SPI>;
+        dma-names = "tx", "rx";
+        pinctrl-names = "default";
+        pinctrl-0 = <&qup_spi1_default>;
+        interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+        spi-max-frequency = <50000000>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+    };
-- 
2.32.0

[PATCH v3 2/2] dt-bindings: qcom: qcom,geni-se: refer to dtschema for SPI

[Krzysztof Kozlowski]

After adding DT schema for the SPI controller, the Qualcomm GENI Serial
Engine QUP Wrapper Controller bindings can reference it directly for
full schema validation.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Kuldeep Singh <singh.kuldeep87k@gmail.com>

---

Changes since v2:
1. Add tag.

Changes since v1:
1. None

Patch depends on previous patch (DT schema conversion).
---
 .../bindings/soc/qcom/qcom,geni-se.yaml       | 22 +------------------
 1 file changed, 1 insertion(+), 21 deletions(-)

diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.yaml b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.yaml
index 690ce6a355de..1bc12b6a7e01 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.yaml
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.yaml
@@ -103,27 +103,7 @@ patternProperties:
                  supports up to 50MHz, up to four chip selects, programmable
                  data path from 4 bits to 32 bits and numerous protocol
                  variants.
-    $ref: /spi/spi-controller.yaml#
-
-    properties:
-      compatible:
-        enum:
-          - qcom,geni-spi
-
-      interrupts:
-        maxItems: 1
-
-      "#address-cells":
-        const: 1
-
-      "#size-cells":
-        const: 0
-
-    required:
-      - compatible
-      - interrupts
-      - "#address-cells"
-      - "#size-cells"
+    $ref: /schemas/spi/qcom,spi-geni-qcom.yaml#
 
   "i2c@[0-9a-f]+$":
     type: object
-- 
2.32.0

Re: [PATCH v3 2/2] dt-bindings: qcom: qcom,geni-se: refer to dtschema for SPI

[Rob Herring]

On Mon, 04 Apr 2022 08:40:17 +0200, Krzysztof Kozlowski wrote:
> After adding DT schema for the SPI controller, the Qualcomm GENI Serial
> Engine QUP Wrapper Controller bindings can reference it directly for
> full schema validation.
> 
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Reviewed-by: Kuldeep Singh <singh.kuldeep87k@gmail.com>
> 
> ---
> 
> Changes since v2:
> 1. Add tag.
> 
> Changes since v1:
> 1. None
> 
> Patch depends on previous patch (DT schema conversion).
> ---
>  .../bindings/soc/qcom/qcom,geni-se.yaml       | 22 +------------------
>  1 file changed, 1 insertion(+), 21 deletions(-)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH v3 1/2] spi: dt-bindings: qcom,spi-geni-qcom: convert to dtschema

[Rob Herring]

On Mon, 04 Apr 2022 08:40:16 +0200, Krzysztof Kozlowski wrote:
> Convert the GENI based Qualcomm Universal Peripheral (QUP) Serial
> Peripheral Interface (SPI) bindings to DT Schema.
> 
> The original bindings in TXT were not complete, so add during conversion
> properties already used in DTS and/or in the driver: dmas,
> interconnects, operating points and power-domains.
> 
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> 
> ---
> 
> Changes since v2:
> 1. Drop reg-names.
> 
> Changes since v1:
> 1. Correct $ref path and remove interconnect minItems (Kuldeep).
> 2. Remove child tpm device from example.
> 3. Pad reg hex addresses with 00.
> ---
>  .../bindings/spi/qcom,spi-geni-qcom.txt       |  39 ------
>  .../bindings/spi/qcom,spi-geni-qcom.yaml      | 116 ++++++++++++++++++
>  2 files changed, 116 insertions(+), 39 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.txt
>  create mode 100644 Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.yaml
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH v3 1/2] spi: dt-bindings: qcom,spi-geni-qcom: convert to dtschema

[Bjorn Andersson]

On Mon, 4 Apr 2022 08:40:16 +0200, Krzysztof Kozlowski wrote:
> Convert the GENI based Qualcomm Universal Peripheral (QUP) Serial
> Peripheral Interface (SPI) bindings to DT Schema.
> 
> The original bindings in TXT were not complete, so add during conversion
> properties already used in DTS and/or in the driver: dmas,
> interconnects, operating points and power-domains.
> 
> [...]

Applied, thanks!

[1/2] spi: dt-bindings: qcom,spi-geni-qcom: convert to dtschema
      commit: 5bdcae1fe1c567c08e8bb7ef20fc70d0b70d5fc4
[2/2] dt-bindings: qcom: qcom,geni-se: refer to dtschema for SPI
      (no commit info)

Best regards,
-- 
Bjorn Andersson <bjorn.andersson@linaro.org>