Re: [PATCH v4 7/7] mtd: spi-nor: macronix: Add Octal 8D-8D-8D supports for Macronix mx25uw51245g

[<Tudor.Ambarus@microchip.com>]

Hi, Mason, YC Lin,

On 5/29/20 10:36 AM, Mason Yang wrote:
> Macronix mx25uw51245g is a SPI NOR that supports 1-1-1/8-8-8 mode.
> 
> Correct the dummy cycles to device for various frequencies
> after xSPI profile 1.0 table parsed.
> 
> Enable mx25uw51245g to Octal DTR mode by executing the command sequences
> to change to octal DTR mode.
> 
> Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
> ---
>  drivers/mtd/spi-nor/macronix.c | 55 ++++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 55 insertions(+)
> 
> diff --git a/drivers/mtd/spi-nor/macronix.c b/drivers/mtd/spi-nor/macronix.c
> index 96735d8..6c9a24c 100644
> --- a/drivers/mtd/spi-nor/macronix.c
> +++ b/drivers/mtd/spi-nor/macronix.c
> @@ -8,6 +8,57 @@
>  
>  #include "core.h"
>  
> +#define MXIC_CR2_DUMMY_SET_ADDR 0x300
> +
> +/* Fixup the dummy cycles to device and setup octa_dtr_enable() */
> +static void mx25uw51245g_post_sfdp_fixups(struct spi_nor *nor)
> +{
> +	struct spi_nor_flash_parameter *params = nor->params;
> +	int ret;
> +	u8 rdc, wdc;
> +
> +	ret = spi_nor_read_cr2(nor, MXIC_CR2_DUMMY_SET_ADDR, &rdc);

nor->bouncebuf is DMA-able, use it instead of rdc

> +	if (ret)
> +		return;
> +
> +	/* Refer to dummy cycle and frequency table(MHz) */
> +	switch (params->dummy_cycles) {
> +	case 10:	/* 10 dummy cycles for 104 MHz */
> +		wdc = 5;
> +		break;
> +	case 12:	/* 12 dummy cycles for 133 MHz */
> +		wdc = 4;
> +		break;
> +	case 16:	/* 16 dummy cycles for 166 MHz */
> +		wdc = 2;
> +		break;
> +	case 18:	/* 18 dummy cycles for 173 MHz */
> +		wdc = 1;
> +		break;
> +	case 20:	/* 20 dummy cycles for 200 MHz */
> +	default:
> +		wdc = 0;
> +	}
> +
> +	if (rdc != wdc)
> +		spi_nor_write_cr2(nor, MXIC_CR2_DUMMY_SET_ADDR, &wdc);
> +
> +	if (params->cmd_seq[0].len) {
> +		params->octal_dtr_enable = spi_nor_cmd_seq_octal_dtr;
> +		params->hwcaps.mask |= SNOR_HWCAPS_READ_8_8_8_DTR;
> +		params->hwcaps.mask |= SNOR_HWCAPS_PP_8_8_8_DTR;
> +
> +	} else {
> +		params->octal_dtr_enable = NULL;
> +		params->hwcaps.mask &= ~SNOR_HWCAPS_READ_8_8_8_DTR;
> +		params->hwcaps.mask &= ~SNOR_HWCAPS_PP_8_8_8_DTR;
> +	}
> +}
> +
> +static struct spi_nor_fixups mx25uw51245g_fixups = {
> +	.post_sfdp = mx25uw51245g_post_sfdp_fixups,
> +};
> +
>  static int
>  mx25l25635_post_bfpt_fixups(struct spi_nor *nor,
>  			    const struct sfdp_parameter_header *bfpt_header,
> @@ -84,6 +135,10 @@
>  			      SPI_NOR_QUAD_READ) },
>  	{ "mx66l1g55g",  INFO(0xc2261b, 0, 64 * 1024, 2048,
>  			      SPI_NOR_QUAD_READ) },
> +	{ "mx25uw51245g", INFO(0xc2813a, 0, 64 * 1024, 1024,
> +			      SECT_4K | SPI_NOR_4B_OPCODES |
> +			      SPI_NOR_OCTAL_DTR_READ)

octal dtr page program is supported?

> +			      .fixups = &mx25uw51245g_fixups },
>  };
>  
>  static void macronix_default_init(struct spi_nor *nor)
> 

Cheers,
ta