Re: [PATCH v2 1/3] staging: rtl8723bs: remove commented out dead code in sdio_halinit.c

[Luka Gejak <lukagejak5@gmail.com>]

LGTM.
Reviewed-by: Luka Gejak <luka.gejak@linux.dev>

On April 12, 2026 5:06:31 PM GMT+02:00, Josh Hesketh <josh.hesketh@gmail.com> wrote:
>Remove commented out dead code that have been dead since the
>driver was introduced to staging. Code can be recovered from
>git history if needed.
>
>Signed-off-by: Josh Hesketh <josh.hesketh@gmail.com>
>---
>v2:
> - Rebased on staging-next
> - Split into separate patches per feedback
> - Removed commented out dead code instead of fixing whitespace
> drivers/staging/rtl8723bs/hal/sdio_halinit.c | 24 --------------------
> 1 file changed, 24 deletions(-)
>
>diff --git a/drivers/staging/rtl8723bs/hal/sdio_halinit.c b/drivers/staging/rtl8723bs/hal/sdio_halinit.c
>index f2f73c65a636..4d74b14c3cd4 100644
>--- a/drivers/staging/rtl8723bs/hal/sdio_halinit.c
>+++ b/drivers/staging/rtl8723bs/hal/sdio_halinit.c
>@@ -46,8 +46,6 @@ u8 _InitPowerOn_8723BS(struct adapter *padapter)
> 	u16 value16;
> 	u32 value32;
> 	u8 ret;
>-/* 	u8 bMacPwrCtrlOn; */
>-
> 
> 	/*  all of these MUST be configured before power on */
> 
>@@ -69,10 +67,6 @@ u8 _InitPowerOn_8723BS(struct adapter *padapter)
> 	value16 |= EnPDN; /*  Enable HW power down and RF on */
> 	rtw_write16(padapter, REG_APS_FSMCO, value16);
> 
>-	/*  Enable CMD53 R/W Operation */
>-/* 	bMacPwrCtrlOn = true; */
>-/* 	rtw_hal_set_hwreg(padapter, HW_VAR_APFM_ON_MAC, &bMacPwrCtrlOn); */
>-
> 	rtw_write8(padapter, REG_CR, 0x00);
> 	/*  Enable MAC DMA/WMAC/SCHEDULE/SEC block */
> 	value16 = rtw_read16(padapter, REG_CR);
>@@ -359,7 +353,6 @@ static void _InitNetworkType(struct adapter *padapter)
> 	value32 = rtw_read32(padapter, REG_CR);
> 
> 	/*  TODO: use the other function to set network type */
>-/* 	value32 = (value32 & ~MASK_NETTYPE) | _NETTYPE(NT_LINK_AD_HOC); */
> 	value32 = (value32 & ~MASK_NETTYPE) | _NETTYPE(NT_LINK_AP);
> 
> 	rtw_write32(padapter, REG_CR, value32);
>@@ -486,9 +479,6 @@ static void _initSdioAggregationSetting(struct adapter *padapter)
> {
> 	struct hal_com_data	*pHalData = GET_HAL_DATA(padapter);
> 
>-	/*  Tx aggregation setting */
>-/* 	sdio_AggSettingTxUpdate(padapter); */
>-
> 	/*  Rx aggregation setting */
> 	HalRxAggr8723BSdio(padapter);
> 
>@@ -640,9 +630,6 @@ u32 rtl8723bs_hal_init(struct adapter *padapter)
> 		return _SUCCESS;
> 	}
> 
>-	/*  Disable Interrupt first. */
>-/* 	rtw_hal_disable_interrupt(padapter); */
>-
> 	ret = _InitPowerOn_8723BS(padapter);
> 	if (ret == _FAIL)
> 		return _FAIL;
>@@ -661,8 +648,6 @@ u32 rtl8723bs_hal_init(struct adapter *padapter)
> 
> 	rtl8723b_InitializeFirmwareVars(padapter);
> 
>-/* 	SIC_Init(padapter); */
>-
> 	if (pwrctrlpriv->reg_rfoff)
> 		pwrctrlpriv->rf_pwrstate = rf_off;
> 
>@@ -745,11 +730,6 @@ u32 rtl8723bs_hal_init(struct adapter *padapter)
> 	rtw_hal_set_chnl_bw(padapter, padapter->registrypriv.channel,
> 		CHANNEL_WIDTH_20, HAL_PRIME_CHNL_OFFSET_DONT_CARE, HAL_PRIME_CHNL_OFFSET_DONT_CARE);
> 
>-	/*  Record original value for template. This is arough data, we can only use the data */
>-	/*  for power adjust. The value can not be adjustde according to different power!!! */
>-/* 	pHalData->OriginalCckTxPwrIdx = pHalData->CurrentCckTxPwrIdx; */
>-/* 	pHalData->OriginalOfdm24GTxPwrIdx = pHalData->CurrentOfdm24GTxPwrIdx; */
>-
> 	rtl8723b_InitAntenna_Selection(padapter);
> 
> 	/*  */
>@@ -791,8 +771,6 @@ u32 rtl8723bs_hal_init(struct adapter *padapter)
> 	/* ack for xmit mgmt frames. */
> 	rtw_write32(padapter, REG_FWHW_TXQ_CTRL, rtw_read32(padapter, REG_FWHW_TXQ_CTRL) | BIT(12));
> 
>-/* 	pHalData->PreRpwmVal = SdioLocalCmd52Read1Byte(padapter, SDIO_REG_HRPWM1) & 0x80; */
>-
> 	{
> 		pwrctrlpriv->rf_pwrstate = rf_on;
> 
>@@ -1080,8 +1058,6 @@ static void _ReadPROMContent(struct adapter *padapter)
> 	pEEPROM->EepromOrEfuse = (eeValue & BOOT_FROM_EEPROM) ? true : false;
> 	pEEPROM->bautoload_fail_flag = (eeValue & EEPROM_EN) ? false : true;
> 
>-/* 	pHalData->EEType = IS_BOOT_FROM_EEPROM(Adapter) ? EEPROM_93C46 : EEPROM_BOOT_EFUSE; */
>-
> 	_ReadEfuseInfo8723BS(padapter);
> }
>