From: Greg KH <gregkh@linuxfoundation.org>
To: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Cc: linux-staging@lists.linux.dev, neil@brown.name
Subject: Re: [PATCH] staging: mt7621-dts: get rid of nodes with no in-tree driver
Date: Mon, 18 Oct 2021 17:48:02 +0200 [thread overview]
Message-ID: <YW2XMkfAdbQm75j+@kroah.com> (raw)
In-Reply-To: <20211018153554.10471-1-sergio.paracuellos@gmail.com>
On Mon, Oct 18, 2021 at 05:35:53PM +0200, Sergio Paracuellos wrote:
> Nodes for 'i2s' and 'nand' have no driver present inside the linux tree.
> The normal approach for a dts file to be mainlined is start with those stuff
> which is already mainlined and get rid of the other stuff. If needed it will
> be properly added afterwards together with the suitable device driver. Hence,
> remove both nodes from the device tree include file.
>
> Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
> ---
> drivers/staging/mt7621-dts/mt7621.dtsi | 36 --------------------------
> 1 file changed, 36 deletions(-)
>
> diff --git a/drivers/staging/mt7621-dts/mt7621.dtsi b/drivers/staging/mt7621-dts/mt7621.dtsi
> index dd7d06c5f234..787220d4d3b4 100644
> --- a/drivers/staging/mt7621-dts/mt7621.dtsi
> +++ b/drivers/staging/mt7621-dts/mt7621.dtsi
> @@ -102,28 +102,6 @@ i2c: i2c@900 {
> pinctrl-0 = <&i2c_pins>;
> };
>
> - i2s: i2s@a00 {
> - compatible = "mediatek,mt7621-i2s";
> - reg = <0xa00 0x100>;
> -
> - clocks = <&sysc MT7621_CLK_I2S>;
> - clock-names = "i2s";
> - resets = <&sysc MT7621_RST_I2S>;
> - reset-names = "i2s";
> -
> - interrupt-parent = <&gic>;
> - interrupts = <GIC_SHARED 16 IRQ_TYPE_LEVEL_HIGH>;
> -
> - txdma-req = <2>;
> - rxdma-req = <3>;
> -
> - dmas = <&gdma 4>,
> - <&gdma 6>;
> - dma-names = "tx", "rx";
> -
> - status = "disabled";
> - };
> -
> memc: syscon@5000 {
> compatible = "mediatek,mt7621-memc", "syscon";
> reg = <0x5000 0x1000>;
> @@ -355,20 +333,6 @@ cdmm: cdmm@1fbf8000 {
> reg = <0x1fbf8000 0x8000>;
> };
>
> - nand: nand@1e003000 {
> - status = "disabled";
> -
> - compatible = "mediatek,mt7621-nand";
> - bank-width = <2>;
> - reg = <0x1e003000 0x800
> - 0x1e003800 0x800>;
> - #address-cells = <1>;
> - #size-cells = <1>;
> -
> - clocks = <&sysc MT7621_CLK_NAND>;
> - clock-names = "nand";
> - };
> -
> ethernet: ethernet@1e100000 {
> compatible = "mediatek,mt7621-eth";
> reg = <0x1e100000 0x10000>;
> --
> 2.33.0
When trying to apply this I get:
checking file drivers/staging/mt7621-dts/mt7621.dtsi
Reversed (or previously applied) patch detected! Assume -R? [n]
Apply anyway? [n]
Skipping patch.
2 out of 2 hunks ignored
Are you sure you rebased?
Hm, ah, I can handle this with fuzz maybe:
patching file drivers/staging/mt7621-dts/mt7621.dtsi
Reversed (or previously applied) patch detected! Assume -R? [n] n
Apply anyway? [n] y
Hunk #1 FAILED at 102.
Hunk #2 succeeded at 358 (offset 3 lines).
1 out of 2 hunks FAILED -- saving rejects to file drivers/staging/mt7621-dts/mt7621.dtsi.rej
Nope, that didn't work.
Again, are you sure you rebased? Against what tree?
thanks,
greg k-h
next prev parent reply other threads:[~2021-10-18 15:48 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-10-18 15:35 [PATCH] staging: mt7621-dts: get rid of nodes with no in-tree driver Sergio Paracuellos
2021-10-18 15:35 ` Sergio Paracuellos
2021-10-18 15:48 ` Greg KH [this message]
2021-10-18 17:02 ` Sergio Paracuellos
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=YW2XMkfAdbQm75j+@kroah.com \
--to=gregkh@linuxfoundation.org \
--cc=linux-staging@lists.linux.dev \
--cc=neil@brown.name \
--cc=sergio.paracuellos@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox