From: Andre Przywara <andre.przywara@arm.com>
To: Chen-Yu Tsai <wens@csie.org>,
Jernej Skrabec <jernej.skrabec@gmail.com>,
Samuel Holland <samuel@sholland.org>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-sunxi@lists.linux.dev, linux-kernel@vger.kernel.org
Subject: [PATCH v12 7/7] arm64: dts: allwinner: h616: Add X96 Mate TV box support
Date: Fri, 1 Jul 2022 12:24:53 +0100 [thread overview]
Message-ID: <20220701112453.2310722-8-andre.przywara@arm.com> (raw)
In-Reply-To: <20220701112453.2310722-1-andre.przywara@arm.com>
The X96 Mate is an Allwinner H616 based TV box, featuring:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 2GiB/4GiB RAM (fully usable!)
- 16/32/64GiB eMMC
- 100Mbps Ethernet (via embedded AC200 EPHY, not yet supported)
- Unsupported Allwinner WiFi chip
- 2 x USB 2.0 host ports
- HDMI port
- IR receiver
- 5V/2A DC power supply via barrel plug
Add a basic devicetree for it, with SD card and eMMC working, as
well as serial and the essential peripherals, like the AXP PMIC.
This DT is somewhat minimal, and should work on many other similar TV
boxes with the Allwinner H616 chip.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../dts/allwinner/sun50i-h616-x96-mate.dts | 177 ++++++++++++++++++
2 files changed, 178 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index df2214e6d946a..6a96494a2e0a3 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -39,3 +39,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6-mini.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts
new file mode 100644
index 0000000000000..30b76140b9c8a
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts
@@ -0,0 +1,177 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2021 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ model = "X96 Mate";
+ compatible = "hechuang,x96-mate", "allwinner,sun50i-h616";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ reg_vcc5v: vcc5v {
+ /* board wide 5V supply directly from the DC input */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+};
+
+&ir {
+ status = "okay";
+};
+
+&mmc0 {
+ vmmc-supply = <®_dcdce>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ bus-width = <4>;
+ status = "okay";
+};
+
+&mmc2 {
+ vmmc-supply = <®_dcdce>;
+ vqmmc-supply = <®_bldo1>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ status = "okay";
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp305: pmic@745 {
+ compatible = "x-powers,axp305", "x-powers,axp805",
+ "x-powers,axp806";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ reg = <0x745>;
+
+ x-powers,self-working-mode;
+ vina-supply = <®_vcc5v>;
+ vinb-supply = <®_vcc5v>;
+ vinc-supply = <®_vcc5v>;
+ vind-supply = <®_vcc5v>;
+ vine-supply = <®_vcc5v>;
+ aldoin-supply = <®_vcc5v>;
+ bldoin-supply = <®_vcc5v>;
+ cldoin-supply = <®_vcc5v>;
+
+ regulators {
+ reg_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-sys";
+ };
+
+ /* Enabled by the Android BSP */
+ reg_aldo2: aldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3-ext";
+ status = "disabled";
+ };
+
+ /* Enabled by the Android BSP */
+ reg_aldo3: aldo3 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3-ext2";
+ status = "disabled";
+ };
+
+ reg_bldo1: bldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc1v8";
+ };
+
+ /* Enabled by the Android BSP */
+ reg_bldo2: bldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc1v8-2";
+ status = "disabled";
+ };
+
+ bldo3 {
+ /* unused */
+ };
+
+ bldo4 {
+ /* unused */
+ };
+
+ cldo1 {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-name = "vcc2v5";
+ };
+
+ cldo2 {
+ /* unused */
+ };
+
+ cldo3 {
+ /* unused */
+ };
+
+ reg_dcdca: dcdca {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1080000>;
+ regulator-name = "vdd-cpu";
+ };
+
+ reg_dcdcc: dcdcc {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1080000>;
+ regulator-name = "vdd-gpu-sys";
+ };
+
+ reg_dcdcd: dcdcd {
+ regulator-always-on;
+ regulator-min-microvolt = <1360000>;
+ regulator-max-microvolt = <1360000>;
+ regulator-name = "vdd-dram";
+ };
+
+ reg_dcdce: dcdce {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-eth-mmc";
+ };
+
+ sw {
+ /* unused */
+ };
+ };
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ph_pins>;
+ status = "okay";
+};
--
2.25.1
next prev parent reply other threads:[~2022-07-01 11:25 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-07-01 11:24 [PATCH v12 0/7] arm64: sunxi: Allwinner H616 SoC DT support Andre Przywara
2022-07-01 11:24 ` [PATCH v12 1/7] dt-bindings: arm: sunxi: Add H616 EMAC compatible Andre Przywara
2022-07-01 20:56 ` Rob Herring
2022-07-04 23:53 ` Samuel Holland
2022-07-05 10:19 ` Andre Przywara
2022-07-06 3:55 ` Samuel Holland
2022-07-11 0:16 ` Andre Przywara
2022-07-01 11:24 ` [PATCH v12 2/7] dt-bindings: pinctrl: sunxi: Make interrupts optional Andre Przywara
2022-07-01 20:57 ` Rob Herring
2022-07-04 23:55 ` Samuel Holland
2022-07-01 11:24 ` [PATCH v12 3/7] arm64: dts: allwinner: Add Allwinner H616 .dtsi file Andre Przywara
2022-07-05 1:16 ` Samuel Holland
2022-07-05 10:42 ` Andre Przywara
2022-07-07 6:36 ` Samuel Holland
2022-07-01 11:24 ` [PATCH v12 4/7] dt-bindings: pinctrl: sunxi: allow vcc-pi-supply Andre Przywara
2022-07-01 20:57 ` Rob Herring
2022-07-05 1:18 ` Samuel Holland
2022-07-01 11:24 ` [PATCH v12 5/7] dt-bindings: arm: sunxi: Add two H616 board compatible strings Andre Przywara
2022-07-01 11:24 ` [PATCH v12 6/7] arm64: dts: allwinner: h616: Add OrangePi Zero 2 board support Andre Przywara
2022-07-05 1:45 ` Samuel Holland
2022-07-08 9:49 ` Andre Przywara
2022-07-01 11:24 ` Andre Przywara [this message]
2022-07-05 1:29 ` [PATCH v12 7/7] arm64: dts: allwinner: h616: Add X96 Mate TV box support Samuel Holland
2022-07-08 9:48 ` Andre Przywara
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220701112453.2310722-8-andre.przywara@arm.com \
--to=andre.przywara@arm.com \
--cc=devicetree@vger.kernel.org \
--cc=jernej.skrabec@gmail.com \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linus.walleij@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-sunxi@lists.linux.dev \
--cc=robh+dt@kernel.org \
--cc=samuel@sholland.org \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox