From: Andre Przywara <andre.przywara@arm.com>
To: u-boot@lists.denx.de
Cc: Tom Rini <trini@konsulko.com>,
Quentin Schulz <quentin.schulz@cherry.de>,
Jernej Skrabec <jernej.skrabec@gmail.com>,
Paul Kocialkowski <contact@paulk.fr>,
linux-sunxi@lists.linux.dev
Subject: [PATCH 3/3] sunxi: configs: enable power LEDs on 64-bit boards
Date: Wed, 8 Apr 2026 00:34:47 +0200 [thread overview]
Message-ID: <20260407223447.4956-4-andre.przywara@arm.com> (raw)
In-Reply-To: <20260407223447.4956-1-andre.przywara@arm.com>
We recently gained a simple way to enable a power LED very early in the
SPL boot, through simple Kconfig variables.
Add those symbols to those boards' defconfigs where the DT indicates a
default-on power LED. The number used is <port bank> * 32 + <pin no>,
an active low setup means CONFIG_SPL_SUNXI_LED_STATUS_STATE must be
undefined.
This will light up the power LED very early in the (SPL) boot phase on
those 64-bit boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
configs/anbernic_rg35xx_h700_defconfig | 3 +++
configs/bananapi_m64_defconfig | 3 +++
configs/beelink_gs1_defconfig | 3 +++
configs/liontron-h-a133l_defconfig | 3 +++
configs/nanopi_neo2_defconfig | 3 +++
configs/nanopi_neo_plus2_defconfig | 3 +++
configs/orangepi_3_defconfig | 3 +++
configs/orangepi_lite2_defconfig | 3 +++
configs/orangepi_pc2_defconfig | 3 +++
configs/orangepi_prime_defconfig | 3 +++
configs/orangepi_zero2_defconfig | 3 +++
configs/orangepi_zero_plus2_defconfig | 3 +++
configs/orangepi_zero_plus_defconfig | 3 +++
configs/radxa-cubie-a5e_defconfig | 3 +++
configs/tanix_tx1_defconfig | 3 +++
15 files changed, 45 insertions(+)
diff --git a/configs/anbernic_rg35xx_h700_defconfig b/configs/anbernic_rg35xx_h700_defconfig
index 2fa57cbecce..fb3df175521 100644
--- a/configs/anbernic_rg35xx_h700_defconfig
+++ b/configs/anbernic_rg35xx_h700_defconfig
@@ -16,6 +16,9 @@ CONFIG_DRAM_SUNXI_PHY_ADDR_MAP_1=y
CONFIG_MACH_SUN50I_H616=y
CONFIG_SUNXI_DRAM_H616_LPDDR4=y
CONFIG_R_I2C_ENABLE=y
+CONFIG_SPL_SUNXI_LED_STATUS=y
+CONFIG_SPL_SUNXI_LED_STATUS_BIT=268
+CONFIG_SPL_SUNXI_LED_STATUS_STATE=y
CONFIG_SPL_I2C=y
CONFIG_SPL_SYS_I2C_LEGACY=y
CONFIG_SYS_I2C_MVTWSI=y
diff --git a/configs/bananapi_m64_defconfig b/configs/bananapi_m64_defconfig
index d957071cb13..413de4919d5 100644
--- a/configs/bananapi_m64_defconfig
+++ b/configs/bananapi_m64_defconfig
@@ -4,6 +4,9 @@ CONFIG_DEFAULT_DEVICE_TREE="sun50i-a64-bananapi-m64"
CONFIG_SPL=y
CONFIG_MACH_SUN50I=y
CONFIG_MMC_SUNXI_SLOT_EXTRA=2
+CONFIG_SPL_SUNXI_LED_STATUS=y
+CONFIG_SPL_SUNXI_LED_STATUS_BIT=120
+CONFIG_SPL_SUNXI_LED_STATUS_STATE=y
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SUPPORT_EMMC_BOOT=y
CONFIG_SUN8I_EMAC=y
diff --git a/configs/beelink_gs1_defconfig b/configs/beelink_gs1_defconfig
index de46d205453..6a1af7f9b3a 100644
--- a/configs/beelink_gs1_defconfig
+++ b/configs/beelink_gs1_defconfig
@@ -5,6 +5,9 @@ CONFIG_SPL=y
CONFIG_MACH_SUN50I_H6=y
CONFIG_SUNXI_DRAM_H6_LPDDR3=y
CONFIG_MMC_SUNXI_SLOT_EXTRA=2
+CONFIG_SPL_SUNXI_LED_STATUS=y
+CONFIG_SPL_SUNXI_LED_STATUS_BIT=356
+CONFIG_SPL_SUNXI_LED_STATUS_STATE=y
# CONFIG_PSCI_RESET is not set
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_LED=y
diff --git a/configs/liontron-h-a133l_defconfig b/configs/liontron-h-a133l_defconfig
index 831d5b56e3a..f7bb994509f 100644
--- a/configs/liontron-h-a133l_defconfig
+++ b/configs/liontron-h-a133l_defconfig
@@ -23,6 +23,9 @@ CONFIG_MACH_SUN50I_A133=y
CONFIG_SUNXI_DRAM_A133_LPDDR4=y
CONFIG_MMC_SUNXI_SLOT_EXTRA=2
CONFIG_R_I2C_ENABLE=y
+CONFIG_SPL_SUNXI_LED_STATUS=y
+CONFIG_SPL_SUNXI_LED_STATUS_BIT=240
+# CONFIG_SPL_SUNXI_LED_STATUS_STATE is not set
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL_I2C=y
CONFIG_SPL_SYS_I2C_LEGACY=y
diff --git a/configs/nanopi_neo2_defconfig b/configs/nanopi_neo2_defconfig
index 6704a24a880..83bf0326bd4 100644
--- a/configs/nanopi_neo2_defconfig
+++ b/configs/nanopi_neo2_defconfig
@@ -6,6 +6,9 @@ CONFIG_SPL=y
CONFIG_MACH_SUN50I_H5=y
CONFIG_DRAM_ZQ=3881977
# CONFIG_DRAM_ODT_EN is not set
+CONFIG_SPL_SUNXI_LED_STATUS=y
+CONFIG_SPL_SUNXI_LED_STATUS_BIT=362
+CONFIG_SPL_SUNXI_LED_STATUS_STATE=y
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SUN8I_EMAC=y
CONFIG_USB_EHCI_HCD=y
diff --git a/configs/nanopi_neo_plus2_defconfig b/configs/nanopi_neo_plus2_defconfig
index e80e32a63d4..024301f990c 100644
--- a/configs/nanopi_neo_plus2_defconfig
+++ b/configs/nanopi_neo_plus2_defconfig
@@ -7,6 +7,9 @@ CONFIG_MACH_SUN50I_H5=y
CONFIG_DRAM_ZQ=3881977
# CONFIG_DRAM_ODT_EN is not set
CONFIG_MMC_SUNXI_SLOT_EXTRA=2
+CONFIG_SPL_SUNXI_LED_STATUS=y
+CONFIG_SPL_SUNXI_LED_STATUS_BIT=362
+CONFIG_SPL_SUNXI_LED_STATUS_STATE=y
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SUN8I_EMAC=y
CONFIG_USB_EHCI_HCD=y
diff --git a/configs/orangepi_3_defconfig b/configs/orangepi_3_defconfig
index 125137bc321..1fa1676e091 100644
--- a/configs/orangepi_3_defconfig
+++ b/configs/orangepi_3_defconfig
@@ -6,6 +6,9 @@ CONFIG_MACH_SUN50I_H6=y
CONFIG_SUNXI_DRAM_H6_LPDDR3=y
CONFIG_MMC_SUNXI_SLOT_EXTRA=2
CONFIG_BLUETOOTH_DT_DEVICE_FIXUP="brcm,bcm4345c5"
+CONFIG_SPL_SUNXI_LED_STATUS=y
+CONFIG_SPL_SUNXI_LED_STATUS_BIT=356
+CONFIG_SPL_SUNXI_LED_STATUS_STATE=y
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_PHY_SUN50I_USB3=y
CONFIG_USB_XHCI_HCD=y
diff --git a/configs/orangepi_lite2_defconfig b/configs/orangepi_lite2_defconfig
index 577f7436c15..10864827adf 100644
--- a/configs/orangepi_lite2_defconfig
+++ b/configs/orangepi_lite2_defconfig
@@ -4,6 +4,9 @@ CONFIG_DEFAULT_DEVICE_TREE="sun50i-h6-orangepi-lite2"
CONFIG_SPL=y
CONFIG_MACH_SUN50I_H6=y
CONFIG_SUNXI_DRAM_H6_LPDDR3=y
+CONFIG_SPL_SUNXI_LED_STATUS=y
+CONFIG_SPL_SUNXI_LED_STATUS_BIT=356
+CONFIG_SPL_SUNXI_LED_STATUS_STATE=y
# CONFIG_PSCI_RESET is not set
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_USB_EHCI_HCD=y
diff --git a/configs/orangepi_pc2_defconfig b/configs/orangepi_pc2_defconfig
index d856a25814b..1e9a7cdaf7a 100644
--- a/configs/orangepi_pc2_defconfig
+++ b/configs/orangepi_pc2_defconfig
@@ -6,6 +6,9 @@ CONFIG_SPL=y
CONFIG_MACH_SUN50I_H5=y
CONFIG_DRAM_ZQ=3881977
CONFIG_SPL_SPI_SUNXI=y
+CONFIG_SPL_SUNXI_LED_STATUS=y
+CONFIG_SPL_SUNXI_LED_STATUS_BIT=362
+CONFIG_SPL_SUNXI_LED_STATUS_STATE=y
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL_I2C=y
CONFIG_SPL_SYS_I2C_LEGACY=y
diff --git a/configs/orangepi_prime_defconfig b/configs/orangepi_prime_defconfig
index e93154cc0e9..7f622fe70f1 100644
--- a/configs/orangepi_prime_defconfig
+++ b/configs/orangepi_prime_defconfig
@@ -6,6 +6,9 @@ CONFIG_SPL=y
CONFIG_MACH_SUN50I_H5=y
CONFIG_DRAM_ZQ=3881977
# CONFIG_DRAM_ODT_EN is not set
+CONFIG_SPL_SUNXI_LED_STATUS=y
+CONFIG_SPL_SUNXI_LED_STATUS_BIT=362
+CONFIG_SPL_SUNXI_LED_STATUS_STATE=y
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SUN8I_EMAC=y
CONFIG_USB_EHCI_HCD=y
diff --git a/configs/orangepi_zero2_defconfig b/configs/orangepi_zero2_defconfig
index 831bfe66e25..942b751e181 100644
--- a/configs/orangepi_zero2_defconfig
+++ b/configs/orangepi_zero2_defconfig
@@ -10,6 +10,9 @@ CONFIG_MACH_SUN50I_H616=y
CONFIG_SUNXI_DRAM_H616_DDR3_1333=y
CONFIG_R_I2C_ENABLE=y
CONFIG_SPL_SPI_SUNXI=y
+CONFIG_SPL_SUNXI_LED_STATUS=y
+CONFIG_SPL_SUNXI_LED_STATUS_BIT=76
+CONFIG_SPL_SUNXI_LED_STATUS_STATE=y
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL_I2C=y
CONFIG_SPL_SYS_I2C_LEGACY=y
diff --git a/configs/orangepi_zero_plus2_defconfig b/configs/orangepi_zero_plus2_defconfig
index c4d9800975c..945379533ab 100644
--- a/configs/orangepi_zero_plus2_defconfig
+++ b/configs/orangepi_zero_plus2_defconfig
@@ -7,6 +7,9 @@ CONFIG_MACH_SUN50I_H5=y
CONFIG_DRAM_ZQ=3881977
# CONFIG_DRAM_ODT_EN is not set
CONFIG_MMC_SUNXI_SLOT_EXTRA=2
+CONFIG_SPL_SUNXI_LED_STATUS=y
+CONFIG_SPL_SUNXI_LED_STATUS_BIT=362
+CONFIG_SPL_SUNXI_LED_STATUS_STATE=y
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SUN8I_EMAC=y
CONFIG_USB_EHCI_HCD=y
diff --git a/configs/orangepi_zero_plus_defconfig b/configs/orangepi_zero_plus_defconfig
index 4b6491dc846..2979c9f7f7b 100644
--- a/configs/orangepi_zero_plus_defconfig
+++ b/configs/orangepi_zero_plus_defconfig
@@ -6,6 +6,9 @@ CONFIG_SPL=y
CONFIG_MACH_SUN50I_H5=y
CONFIG_DRAM_ZQ=3881977
# CONFIG_DRAM_ODT_EN is not set
+CONFIG_SPL_SUNXI_LED_STATUS=y
+CONFIG_SPL_SUNXI_LED_STATUS_BIT=362
+CONFIG_SPL_SUNXI_LED_STATUS_STATE=y
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SUN8I_EMAC=y
CONFIG_USB_EHCI_HCD=y
diff --git a/configs/radxa-cubie-a5e_defconfig b/configs/radxa-cubie-a5e_defconfig
index 9d204ef5548..88e9a0879f7 100644
--- a/configs/radxa-cubie-a5e_defconfig
+++ b/configs/radxa-cubie-a5e_defconfig
@@ -15,6 +15,9 @@ CONFIG_DRAM_SUNXI_TPR12=0x3533302f
CONFIG_MACH_SUN55I_A523=y
CONFIG_MMC_SUNXI_SLOT_EXTRA=2
CONFIG_R_I2C_ENABLE=y
+CONFIG_SPL_SUNXI_LED_STATUS=y
+CONFIG_SPL_SUNXI_LED_STATUS_BIT=356
+# CONFIG_SPL_SUNXI_LED_STATUS_STATE is not set
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL_I2C=y
CONFIG_SPL_SYS_I2C_LEGACY=y
diff --git a/configs/tanix_tx1_defconfig b/configs/tanix_tx1_defconfig
index 1bd167ce0f6..0b5c57b93b9 100644
--- a/configs/tanix_tx1_defconfig
+++ b/configs/tanix_tx1_defconfig
@@ -14,6 +14,9 @@ CONFIG_MACH_SUN50I_H616=y
CONFIG_SUNXI_DRAM_H616_LPDDR3=y
CONFIG_MMC_SUNXI_SLOT_EXTRA=2
CONFIG_R_I2C_ENABLE=y
+CONFIG_SPL_SUNXI_LED_STATUS=y
+CONFIG_SPL_SUNXI_LED_STATUS_BIT=231
+CONFIG_SPL_SUNXI_LED_STATUS_STATE=y
# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
CONFIG_SPL_I2C=y
CONFIG_SPL_SYS_I2C_LEGACY=y
--
2.46.4
prev parent reply other threads:[~2026-04-07 22:35 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-04-07 22:34 [PATCH 0/3] sunxi: Fix and extend SPL power LED support Andre Przywara
2026-04-07 22:34 ` [PATCH 1/3] sunxi: spl: fix SPL_SUNXI_LED active low configuration Andre Przywara
2026-04-08 8:27 ` Quentin Schulz
2026-04-09 15:56 ` Paul Kocialkowski
2026-04-07 22:34 ` [PATCH 2/3] sunxi: configs: enable power LEDs on 32-bit boards Andre Przywara
2026-04-07 22:34 ` Andre Przywara [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260407223447.4956-4-andre.przywara@arm.com \
--to=andre.przywara@arm.com \
--cc=contact@paulk.fr \
--cc=jernej.skrabec@gmail.com \
--cc=linux-sunxi@lists.linux.dev \
--cc=quentin.schulz@cherry.de \
--cc=trini@konsulko.com \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox