From mboxrd@z Thu Jan 1 00:00:00 1970 From: Dmitry Osipenko Subject: [PATCH v7 06/12] ARM: tegra: Switch CPU to PLLP on resume from LP1 on Tegra30/114/124 Date: Thu, 13 Feb 2020 02:46:01 +0300 Message-ID: <20200212234607.11521-7-digetx@gmail.com> References: <20200212234607.11521-1-digetx@gmail.com> Mime-Version: 1.0 Content-Transfer-Encoding: 8bit Return-path: In-Reply-To: <20200212234607.11521-1-digetx-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> Sender: linux-tegra-owner-u79uwXL29TY76Z2rM5mHXA@public.gmane.org To: Thierry Reding , Jonathan Hunter , Peter De Schrijver , Prashant Gaikwad , "Rafael J. Wysocki" , Viresh Kumar , Michael Turquette , Stephen Boyd , Peter Geis , Nicolas Chauvet , Marcel Ziswiler , =?UTF-8?q?Micha=C5=82=20Miros=C5=82aw?= , Jasper Korten , David Heidelberg Cc: linux-pm-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-clk-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org List-Id: linux-tegra@vger.kernel.org The early-resume code shall not switch CPU to PLLX because PLLX configuration could be unstable or PLLX should be simply disabled if CPU enters into suspend running off some other PLL (the case if CPUFREQ driver is active). The actual burst policy is restored by the clock drivers. Acked-by: Peter De Schrijver Tested-by: Peter Geis Tested-by: Marcel Ziswiler Tested-by: Jasper Korten Tested-by: David Heidelberg Signed-off-by: Dmitry Osipenko --- arch/arm/mach-tegra/sleep-tegra30.S | 7 ++----- 1 file changed, 2 insertions(+), 5 deletions(-) diff --git a/arch/arm/mach-tegra/sleep-tegra30.S b/arch/arm/mach-tegra/sleep-tegra30.S index 02cc6ff96f30..b897d4a433b3 100644 --- a/arch/arm/mach-tegra/sleep-tegra30.S +++ b/arch/arm/mach-tegra/sleep-tegra30.S @@ -398,11 +398,8 @@ _pll_m_c_x_done: ldr r4, [r5, #0x1C] @ restore SCLK_BURST str r4, [r0, #CLK_RESET_SCLK_BURST] - cmp r10, #TEGRA30 - movweq r4, #:lower16:((1 << 28) | (0x8)) @ burst policy is PLLX - movteq r4, #:upper16:((1 << 28) | (0x8)) - movwne r4, #:lower16:((1 << 28) | (0xe)) - movtne r4, #:upper16:((1 << 28) | (0xe)) + movw r4, #:lower16:((1 << 28) | (0x4)) @ burst policy is PLLP + movt r4, #:upper16:((1 << 28) | (0x4)) str r4, [r0, #CLK_RESET_CCLK_BURST] /* Restore pad power state to normal */ -- 2.24.0