From mboxrd@z Thu Jan 1 00:00:00 1970 From: Jon Hunter Subject: Re: [PATCH net-next 3/3] net: stmmac: Introducing support for Page Pool Date: Wed, 24 Jul 2019 12:10:47 +0100 Message-ID: <33de62bf-2f8a-bf00-9260-418b12bed24c@nvidia.com> References: <6c769226-bdd9-6fe0-b96b-5a0d800fed24@arm.com> <8756d681-e167-fe4a-c6f0-47ae2dcbb100@nvidia.com> <20190723.115112.1824255524103179323.davem@davemloft.net> <20190724085427.GA10736@apalos> <20190724095310.GA12991@apalos> Mime-Version: 1.0 Content-Type: text/plain; charset="utf-8" Content-Transfer-Encoding: 7bit Return-path: In-Reply-To: Content-Language: en-US Sender: linux-kernel-owner@vger.kernel.org To: Jose Abreu , Ilias Apalodimas Cc: David Miller , "robin.murphy@arm.com" , "lists@bofh.nu" , "Joao.Pinto@synopsys.com" , "alexandre.torgue@st.com" , "maxime.ripard@bootlin.com" , "netdev@vger.kernel.org" , "linux-kernel@vger.kernel.org" , "linux-stm32@st-md-mailman.stormreply.com" , "wens@csie.org" , "mcoquelin.stm32@gmail.com" , "linux-tegra@vger.kernel.org" , "peppe.cavallaro@st.com" , "linux-arm-kernel@lists.infradead.org" List-Id: linux-tegra@vger.kernel.org On 24/07/2019 11:04, Jose Abreu wrote: ... > Jon, I was able to replicate (at some level) your setup: > > # dmesg | grep -i arm-smmu > [ 1.337322] arm-smmu 70040000.iommu: probing hardware > configuration... > [ 1.337330] arm-smmu 70040000.iommu: SMMUv2 with: > [ 1.337338] arm-smmu 70040000.iommu: stage 1 translation > [ 1.337346] arm-smmu 70040000.iommu: stage 2 translation > [ 1.337354] arm-smmu 70040000.iommu: nested translation > [ 1.337363] arm-smmu 70040000.iommu: stream matching with 128 > register groups > [ 1.337374] arm-smmu 70040000.iommu: 1 context banks (0 > stage-2 only) > [ 1.337383] arm-smmu 70040000.iommu: Supported page sizes: > 0x61311000 > [ 1.337393] arm-smmu 70040000.iommu: Stage-1: 48-bit VA -> > 48-bit IPA > [ 1.337402] arm-smmu 70040000.iommu: Stage-2: 48-bit IPA -> > 48-bit PA > > # dmesg | grep -i stmmac > [ 1.344106] stmmaceth 70000000.ethernet: Adding to iommu group 0 > [ 1.344233] stmmaceth 70000000.ethernet: no reset control found > [ 1.348276] stmmaceth 70000000.ethernet: User ID: 0x10, Synopsys ID: > 0x51 > [ 1.348285] stmmaceth 70000000.ethernet: DWMAC4/5 > [ 1.348293] stmmaceth 70000000.ethernet: DMA HW capability register > supported > [ 1.348302] stmmaceth 70000000.ethernet: RX Checksum Offload Engine > supported > [ 1.348311] stmmaceth 70000000.ethernet: TX Checksum insertion > supported > [ 1.348320] stmmaceth 70000000.ethernet: TSO supported > [ 1.348328] stmmaceth 70000000.ethernet: Enable RX Mitigation via HW > Watchdog Timer > [ 1.348337] stmmaceth 70000000.ethernet: TSO feature enabled > [ 1.348409] libphy: stmmac: probed > [ 4159.140990] stmmaceth 70000000.ethernet eth0: PHY [stmmac-0:01] > driver [Generic PHY] > [ 4159.141005] stmmaceth 70000000.ethernet eth0: phy: setting supported > 00,00000000,000062ff advertising 00,00000000,000062ff > [ 4159.142359] stmmaceth 70000000.ethernet eth0: No Safety Features > support found > [ 4159.142369] stmmaceth 70000000.ethernet eth0: IEEE 1588-2008 Advanced > Timestamp supported > [ 4159.142429] stmmaceth 70000000.ethernet eth0: registered PTP clock > [ 4159.142439] stmmaceth 70000000.ethernet eth0: configuring for > phy/gmii link mode > [ 4159.142452] stmmaceth 70000000.ethernet eth0: phylink_mac_config: > mode=phy/gmii/Unknown/Unknown adv=00,00000000,000062ff pause=10 link=0 > an=1 > [ 4159.142466] stmmaceth 70000000.ethernet eth0: phy link up > gmii/1Gbps/Full > [ 4159.142475] stmmaceth 70000000.ethernet eth0: phylink_mac_config: > mode=phy/gmii/1Gbps/Full adv=00,00000000,00000000 pause=0f link=1 an=0 > [ 4159.142481] stmmaceth 70000000.ethernet eth0: Link is Up - 1Gbps/Full > - flow control rx/tx > > The only missing point is the NFS boot that I can't replicate with this > setup. But I did some sanity checks: > > Remote Enpoint: > # dd if=/dev/urandom of=output.dat bs=128M count=1 > # nc -c 192.168.0.2 1234 < output.dat > # md5sum output.dat > fde9e0818281836e4fc0edfede2b8762 output.dat > > DUT: > # nc -l -c -p 1234 > output.dat > # md5sum output.dat > fde9e0818281836e4fc0edfede2b8762 output.dat On my setup, if I do not use NFS to mount the rootfs, but then manually mount the NFS share after booting, I do not see any problems reading or writing to files on the share. So I am not sure if it is some sort of race that is occurring when mounting the NFS share on boot. It is 100% reproducible when using NFS for the root file-system. I am using the Jetson TX2 devkit [0] to test this. Cheers Jon [0] https://developer.nvidia.com/embedded/jetson-tx2-developer-kit -- nvpublic