* RE: [PATCH V3 0/3] ADD AHCI support for tegra210 [not found] ` <1494581650-11115-1-git-send-email-pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> @ 2017-05-12 9:45 ` Preetham Chandru 0 siblings, 0 replies; 14+ messages in thread From: Preetham Chandru @ 2017-05-12 9:45 UTC (permalink / raw) To: thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org Cc: tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Laxman Dewangan, preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, Venu Byravarasu, Pavan Kunapuli, linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org +CC linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org >-----Original Message----- >From: Preetham Chandru >Sent: Friday, May 12, 2017 3:04 PM >To: thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org >Cc: tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; Laxman Dewangan ><ldewangan-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; Venu Byravarasu ><vbyravarasu-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; Pavan Kunapuli <pkunapuli-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; Preetham >Chandru <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >Subject: [PATCH V3 0/3] ADD AHCI support for tegra210 > >From: Preetham Chandru R <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> > >1. ADD AHCI support for tegra210 >2. Extend the tegra AHCI controller device tree binding with tegra210 >--- >Preetham Chandru R (3): > ata: ahci_tegra: Add AHCI support for tegra210 > dt-bindings: tegra: Add tegra210 AHCI > arm64: tegra: Enable SATA on Tegra210 > > .../bindings/ata/nvidia,tegra124-ahci.txt | 45 ++- > arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi | 6 + > arch/arm64/boot/dts/nvidia/tegra210.dtsi | 16 + > drivers/ata/ahci_tegra.c | 377 ++++++++++++++++----- > 4 files changed, 346 insertions(+), 98 deletions(-) > >-- >2.1.4 ^ permalink raw reply [flat|nested] 14+ messages in thread
[parent not found: <1494581650-11115-2-git-send-email-pchandru@nvidia.com>]
[parent not found: <1494581650-11115-2-git-send-email-pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>]
* RE: [PATCH V3 1/3] ata: ahci_tegra: Add AHCI support for tegra210 [not found] ` <1494581650-11115-2-git-send-email-pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> @ 2017-05-12 9:55 ` Preetham Chandru [not found] ` <c3457c8e12b0402293bdea825883277f-7W72rfoJkVnYuxH7O460wFaTQe2KTcn/@public.gmane.org> 0 siblings, 1 reply; 14+ messages in thread From: Preetham Chandru @ 2017-05-12 9:55 UTC (permalink / raw) To: thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org Cc: tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Laxman Dewangan, preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, Venu Byravarasu, Pavan Kunapuli, linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org +CC linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org >-----Original Message----- >From: Preetham Chandru >Sent: Friday, May 12, 2017 3:04 PM >To: thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org >Cc: tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; Laxman Dewangan ><ldewangan-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; Venu Byravarasu ><vbyravarasu-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; Pavan Kunapuli <pkunapuli-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; Preetham >Chandru <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >Subject: [PATCH V3 1/3] ata: ahci_tegra: Add AHCI support for tegra210 > >From: Preetham Chandru R <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> > >1. Move tegra124 specifics to tegra124_ahci_init. >2. Separate the regulators needed for tegra124 and tegra210. >3. Disable DIPM and Devslp for t210 and t124 as there are known issues > >Signed-off-by: Preetham Chandru R <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >--- >v3: >* Remove inline functions for read/write and modify to > SATA, SATA Config and SATA Aux registers. >* Add code to disable DIPM and DevSlp for t210 and t124 >v2: >* Fix indentation issues >* Move the change to disable DIPM, HIPM, DevSlp, partial, > slumber and NCQ into a separate patch >--- > drivers/ata/ahci_tegra.c | 377 ++++++++++++++++++++++++++++++++++++------- >---- > 1 file changed, 293 insertions(+), 84 deletions(-) > >diff --git a/drivers/ata/ahci_tegra.c b/drivers/ata/ahci_tegra.c index >3a62eb2..cd581a6 100644 >--- a/drivers/ata/ahci_tegra.c >+++ b/drivers/ata/ahci_tegra.c >@@ -34,7 +34,8 @@ > #define DRV_NAME "tegra-ahci" > > #define SATA_CONFIGURATION_0 0x180 >-#define SATA_CONFIGURATION_EN_FPCI BIT(0) >+#define SATA_CONFIGURATION_0_EN_FPCI BIT(0) >+#define SATA_CONFIGURATION_0_CLK_OVERRIDE BIT(31) > > #define SCFG_OFFSET 0x1000 > >@@ -45,17 +46,55 @@ > #define T_SATA0_CFG_1_SERR BIT(8) > > #define T_SATA0_CFG_9 0x24 >-#define T_SATA0_CFG_9_BASE_ADDRESS_SHIFT 13 >+#define T_SATA0_CFG_9_BASE_ADDRESS 0x40020000 > > #define SATA_FPCI_BAR5 0x94 >-#define SATA_FPCI_BAR5_START_SHIFT 4 >+#define SATA_FPCI_BAR5_START_MASK (0xfffffff << 4) >+#define SATA_FPCI_BAR5_START (0x0040020 << >4) >+#define SATA_FPCI_BAR5_ACCESS_TYPE (0x1) > > #define SATA_INTR_MASK 0x188 > #define SATA_INTR_MASK_IP_INT_MASK BIT(16) > >+#define T_SATA0_CFG_35 0x94 >+#define T_SATA0_CFG_35_IDP_INDEX_MASK (0x7ff << 2) >+#define T_SATA0_CFG_35_IDP_INDEX (0x2a << 2) >+ >+#define T_SATA0_AHCI_IDP1 0x98 >+#define T_SATA0_AHCI_IDP1_DATA (0x400040) >+ >+#define T_SATA0_CFG_PHY_1 0x12c >+#define T_SATA0_CFG_PHY_1_PADS_IDDQ_EN BIT(23) >+#define T_SATA0_CFG_PHY_1_PAD_PLL_IDDQ_EN BIT(22) >+ >+#define T_SATA0_NVOOB 0x114 >+#define T_SATA0_NVOOB_COMMA_CNT_MASK (0xff << 16) >+#define T_SATA0_NVOOB_COMMA_CNT (0x07 << 16) >+#define T_SATA0_NVOOB_SQUELCH_FILTER_MODE_MASK (0x3 << 24) >+#define T_SATA0_NVOOB_SQUELCH_FILTER_MODE (0x1 << 24) >+#define T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH_MASK (0x3 << 26) >+#define T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH (0x3 << 26) >+ >+#define T_SATA_CFG_PHY_0 0x120 >+#define T_SATA_CFG_PHY_0_USE_7BIT_ALIGN_DET_FOR_SPD BIT(11) >+#define T_SATA_CFG_PHY_0_MASK_SQUELCH BIT(24) >+ >+#define T_SATA0_CFG2NVOOB_2 0x134 >+#define T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW_MASK (0x1ff ><< 18) >+#define T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW (0xc << 18) >+ > #define T_SATA0_AHCI_HBA_CAP_BKDR 0x300 >+#define T_SATA0_AHCI_HBA_CAP_BKDR_PARTIAL_ST_CAP BIT(13) >+#define T_SATA0_AHCI_HBA_CAP_BKDR_SLUMBER_ST_CAP BIT(14) >+#define T_SATA0_AHCI_HBA_CAP_BKDR_SALP BIT(26) >+#define T_SATA0_AHCI_HBA_CAP_BKDR_SUPP_PM BIT(17) >+#define T_SATA0_AHCI_HBA_CAP_BKDR_SNCQ BIT(30) > > #define T_SATA0_BKDOOR_CC 0x4a4 >+#define T_SATA0_BKDOOR_CC_CLASS_CODE_MASK (0xffff << 16) >+#define T_SATA0_BKDOOR_CC_CLASS_CODE (0x0106 << 16) >+#define T_SATA0_BKDOOR_CC_PROG_IF_MASK (0xff << 8) >+#define T_SATA0_BKDOOR_CC_PROG_IF (0x01 << 8) > > #define T_SATA0_CFG_SATA 0x54c > #define T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN BIT(12) >@@ -82,9 +121,35 @@ > #define T_SATA0_CHX_PHY_CTRL11 0x6d0 > #define T_SATA0_CHX_PHY_CTRL11_GEN2_RX_EQ (0x2800 << 16) > >+#define T_SATA0_CHX_PHY_CTRL17_0 0x6e8 >+#define T_SATA0_CHX_PHY_CTRL17_0_RX_EQ_CTRL_L_GEN1 0x55010000 >+#define T_SATA0_CHX_PHY_CTRL18_0 0x6ec >+#define T_SATA0_CHX_PHY_CTRL18_0_RX_EQ_CTRL_L_GEN2 0x55010000 >+#define T_SATA0_CHX_PHY_CTRL20_0 0x6f4 >+#define T_SATA0_CHX_PHY_CTRL20_0_RX_EQ_CTRL_H_GEN1 0x1 >+#define T_SATA0_CHX_PHY_CTRL21_0 0x6f8 >+#define T_SATA0_CHX_PHY_CTRL21_0_RX_EQ_CTRL_H_GEN2 0x1 >+ >+/* AUX Registers */ >+#define SATA_AUX_MISC_CNTL_1_0 0x8 >+#define SATA_AUX_MISC_CNTL_1_0_DEVSLP_OVERRIDE BIT(17) >+#define SATA_AUX_MISC_CNTL_1_0_SDS_SUPPORT BIT(13) >+#define SATA_AUX_MISC_CNTL_1_0_DESO_SUPPORT BIT(15) >+ >+#define SATA_AUX_RX_STAT_INT_0 0xc >+#define SATA_AUX_RX_STAT_INT_0_SATA_DEVSLP BIT(7) >+ >+#define SATA_AUX_SPARE_CFG0_0 0x18 >+#define SATA_AUX_SPARE_CFG0_0_MDAT_TIMER_AFTER_PG_VALID BIT(14) >+ > #define FUSE_SATA_CALIB 0x124 > #define FUSE_SATA_CALIB_MASK 0x3 > >+enum { >+ NO_DEVSLP = (1 << 0), >+ NO_DIPM = (1 << 1), >+}; >+ > struct sata_pad_calibration { > u8 gen1_tx_amp; > u8 gen1_tx_peak; >@@ -99,15 +164,89 @@ static const struct sata_pad_calibration >tegra124_pad_calibration[] = { > {0x14, 0x0e, 0x1a, 0x0e}, > }; > >+struct tegra_ahci_ops { >+ int (*init)(struct ahci_host_priv *); >+}; >+ >+struct tegra_ahci_soc { >+ const char *const *supply_names; >+ u32 num_supplies; >+ u32 quirks; >+ struct tegra_ahci_ops ops; >+}; >+ > struct tegra_ahci_priv { > struct platform_device *pdev; > void __iomem *sata_regs; >+ void __iomem *sata_aux_regs; > struct reset_control *sata_rst; > struct reset_control *sata_oob_rst; > struct reset_control *sata_cold_rst; > /* Needs special handling, cannot use ahci_platform */ > struct clk *sata_clk; >- struct regulator_bulk_data supplies[5]; >+ struct regulator_bulk_data *supplies; >+ struct tegra_ahci_soc *soc_data; >+}; >+ >+static const char *const tegra124_supply_names[] = { >+ "avdd", "hvdd", "vddio", "target-5v", "target-12v" >+}; >+ >+static int tegra124_ahci_init(struct ahci_host_priv *hpriv) { >+ struct tegra_ahci_priv *tegra = hpriv->plat_data; >+ struct sata_pad_calibration calib; >+ int ret; >+ u32 val; >+ >+ /* Pad calibration */ >+ ret = tegra_fuse_readl(FUSE_SATA_CALIB, &val); >+ if (ret) >+ return ret; >+ >+ calib = tegra124_pad_calibration[val & FUSE_SATA_CALIB_MASK]; >+ >+ writel(BIT(0), tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX); >+ >+ val = readl(tegra->sata_regs + >+ SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN1); >+ val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_MASK; >+ val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_MASK; >+ val |= calib.gen1_tx_amp << >T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT; >+ val |= calib.gen1_tx_peak << >T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT; >+ writel(val, tegra->sata_regs + SCFG_OFFSET + >+ T_SATA0_CHX_PHY_CTRL1_GEN1); >+ >+ val = readl(tegra->sata_regs + >+ SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN2); >+ val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_AMP_MASK; >+ val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_PEAK_MASK; >+ val |= calib.gen2_tx_amp << >T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT; >+ val |= calib.gen2_tx_peak << >T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT; >+ writel(val, tegra->sata_regs + SCFG_OFFSET + >+ T_SATA0_CHX_PHY_CTRL1_GEN2); >+ >+ writel(T_SATA0_CHX_PHY_CTRL11_GEN2_RX_EQ, >+ tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL11); >+ writel(T_SATA0_CHX_PHY_CTRL2_CDR_CNTL_GEN1, >+ tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL2); >+ >+ writel(0, tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX); >+ >+ return 0; >+} >+ >+static const struct tegra_ahci_soc tegra124_ahci_soc_data = { >+ .supply_names = tegra124_supply_names, >+ .num_supplies = ARRAY_SIZE(tegra124_supply_names), >+ .quirks = NO_DIPM | NO_DEVSLP, >+ .ops = { >+ .init = tegra124_ahci_init, >+ }, >+}; >+ >+static const struct tegra_ahci_soc tegra210_ahci_soc_data = { >+ .quirks = NO_DIPM | NO_DEVSLP, > }; > > static int tegra_ahci_power_on(struct ahci_host_priv *hpriv) @@ -115,7 +254,7 >@@ static int tegra_ahci_power_on(struct ahci_host_priv *hpriv) > struct tegra_ahci_priv *tegra = hpriv->plat_data; > int ret; > >- ret = regulator_bulk_enable(ARRAY_SIZE(tegra->supplies), >+ ret = regulator_bulk_enable(tegra->soc_data->num_supplies, > tegra->supplies); > if (ret) > return ret; >@@ -144,8 +283,7 @@ static int tegra_ahci_power_on(struct ahci_host_priv >*hpriv) > tegra_powergate_power_off(TEGRA_POWERGATE_SATA); > > disable_regulators: >- regulator_bulk_disable(ARRAY_SIZE(tegra->supplies), tegra->supplies); >- >+ regulator_bulk_disable(tegra->soc_data->num_supplies, >+tegra->supplies); > return ret; > } > >@@ -162,97 +300,137 @@ static void tegra_ahci_power_off(struct >ahci_host_priv *hpriv) > clk_disable_unprepare(tegra->sata_clk); > tegra_powergate_power_off(TEGRA_POWERGATE_SATA); > >- regulator_bulk_disable(ARRAY_SIZE(tegra->supplies), tegra->supplies); >+ regulator_bulk_disable(tegra->soc_data->num_supplies, >+tegra->supplies); > } > > static int tegra_ahci_controller_init(struct ahci_host_priv *hpriv) { > struct tegra_ahci_priv *tegra = hpriv->plat_data; > int ret; >- unsigned int val; >- struct sata_pad_calibration calib; >+ u32 val; > > ret = tegra_ahci_power_on(hpriv); >- if (ret) { >- dev_err(&tegra->pdev->dev, >- "failed to power on AHCI controller: %d\n", ret); >+ if (ret) > return ret; >- } > >+ /* >+ * Program the following SATA IPFS registers >+ * to allow SW accesses to SATA's MMIO Register >+ */ >+ val = readl(tegra->sata_regs + SATA_FPCI_BAR5); >+ val &= ~(SATA_FPCI_BAR5_START_MASK | >SATA_FPCI_BAR5_ACCESS_TYPE); >+ val |= SATA_FPCI_BAR5_START | SATA_FPCI_BAR5_ACCESS_TYPE; >+ writel(val, tegra->sata_regs + SATA_FPCI_BAR5); >+ >+ /* Program the following SATA IPFS register to enable the SATA */ > val = readl(tegra->sata_regs + SATA_CONFIGURATION_0); >- val |= SATA_CONFIGURATION_EN_FPCI; >+ val |= SATA_CONFIGURATION_0_EN_FPCI; > writel(val, tegra->sata_regs + SATA_CONFIGURATION_0); > >- /* Pad calibration */ >- >- ret = tegra_fuse_readl(FUSE_SATA_CALIB, &val); >- if (ret) { >- dev_err(&tegra->pdev->dev, >- "failed to read calibration fuse: %d\n", ret); >- return ret; >- } >- >- calib = tegra124_pad_calibration[val & FUSE_SATA_CALIB_MASK]; >- >- writel(BIT(0), tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX); >- >- val = readl(tegra->sata_regs + >- SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN1); >- val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_MASK; >- val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_MASK; >- val |= calib.gen1_tx_amp << >- T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT; >- val |= calib.gen1_tx_peak << >- T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT; >- writel(val, tegra->sata_regs + SCFG_OFFSET + >- T_SATA0_CHX_PHY_CTRL1_GEN1); >- >- val = readl(tegra->sata_regs + >- SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN2); >- val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_AMP_MASK; >- val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_PEAK_MASK; >- val |= calib.gen2_tx_amp << >- T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT; >- val |= calib.gen2_tx_peak << >- T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT; >- writel(val, tegra->sata_regs + SCFG_OFFSET + >- T_SATA0_CHX_PHY_CTRL1_GEN2); >- >- writel(T_SATA0_CHX_PHY_CTRL11_GEN2_RX_EQ, >- tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL11); >- writel(T_SATA0_CHX_PHY_CTRL2_CDR_CNTL_GEN1, >- tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL2); >- >- writel(0, tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX); >- >- /* Program controller device ID */ >+ /* Electrical settings for better link stability */ >+ val = T_SATA0_CHX_PHY_CTRL17_0_RX_EQ_CTRL_L_GEN1; >+ writel(val, tegra->sata_regs + SCFG_OFFSET + >T_SATA0_CHX_PHY_CTRL17_0); >+ val = T_SATA0_CHX_PHY_CTRL18_0_RX_EQ_CTRL_L_GEN2; >+ writel(val, tegra->sata_regs + SCFG_OFFSET + >T_SATA0_CHX_PHY_CTRL18_0); >+ val = T_SATA0_CHX_PHY_CTRL20_0_RX_EQ_CTRL_H_GEN1; >+ writel(val, tegra->sata_regs + SCFG_OFFSET + >T_SATA0_CHX_PHY_CTRL20_0); >+ val = T_SATA0_CHX_PHY_CTRL21_0_RX_EQ_CTRL_H_GEN2; >+ writel(val, tegra->sata_regs + SCFG_OFFSET + >+T_SATA0_CHX_PHY_CTRL21_0); >+ >+ /* For SQUELCH Filter & Gen3 drive getting detected as Gen1 drive */ >+ >+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA_CFG_PHY_0); >+ val |= T_SATA_CFG_PHY_0_MASK_SQUELCH; >+ val &= ~T_SATA_CFG_PHY_0_USE_7BIT_ALIGN_DET_FOR_SPD; >+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA_CFG_PHY_0); >+ >+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_NVOOB); >+ val &= ~(T_SATA0_NVOOB_COMMA_CNT_MASK | >+ T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH_MASK | >+ T_SATA0_NVOOB_SQUELCH_FILTER_MODE_MASK); >+ val |= (T_SATA0_NVOOB_COMMA_CNT | >+ T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH | >+ T_SATA0_NVOOB_SQUELCH_FILTER_MODE); >+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_NVOOB); >+ >+ /* >+ * Change CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW from 83.3 ns to >58.8ns >+ */ >+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG2NVOOB_2); >+ val &= ~T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW_MASK; >+ val |= T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW; >+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG2NVOOB_2); >+ >+ if (tegra->soc_data->ops.init) >+ tegra->soc_data->ops.init(hpriv); >+ >+ /* >+ * Program the following SATA configuration registers >+ * to initialize SATA >+ */ >+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1); >+ val |= (T_SATA0_CFG_1_IO_SPACE | T_SATA0_CFG_1_MEMORY_SPACE | >+ T_SATA0_CFG_1_BUS_MASTER | T_SATA0_CFG_1_SERR); >+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1); >+ val = T_SATA0_CFG_9_BASE_ADDRESS; >+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_9); > >+ /* Program Class Code and Programming interface for SATA */ > val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA); > val |= T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN; > writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA); > >- writel(0x01060100, tegra->sata_regs + SCFG_OFFSET + >T_SATA0_BKDOOR_CC); >+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_BKDOOR_CC); >+ val &= >+ ~(T_SATA0_BKDOOR_CC_CLASS_CODE_MASK | >+ T_SATA0_BKDOOR_CC_PROG_IF_MASK); >+ val |= T_SATA0_BKDOOR_CC_CLASS_CODE | >T_SATA0_BKDOOR_CC_PROG_IF; >+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_BKDOOR_CC); > > val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA); > val &= ~T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN; > writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA); > >- /* Enable IO & memory access, bus master mode */ >- >- val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1); >- val |= T_SATA0_CFG_1_IO_SPACE | T_SATA0_CFG_1_MEMORY_SPACE | >- T_SATA0_CFG_1_BUS_MASTER | T_SATA0_CFG_1_SERR; >- writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1); >- >- /* Program SATA MMIO */ >- >- writel(0x10000 << SATA_FPCI_BAR5_START_SHIFT, >- tegra->sata_regs + SATA_FPCI_BAR5); >- >- writel(0x08000 << T_SATA0_CFG_9_BASE_ADDRESS_SHIFT, >- tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_9); >+ /* Enabling LPM capabilities through Backdoor Programming */ >+ val = readl(tegra->sata_regs + SCFG_OFFSET + >T_SATA0_AHCI_HBA_CAP_BKDR); >+ val |= (T_SATA0_AHCI_HBA_CAP_BKDR_PARTIAL_ST_CAP | >+ T_SATA0_AHCI_HBA_CAP_BKDR_SLUMBER_ST_CAP | >+ T_SATA0_AHCI_HBA_CAP_BKDR_SALP | >+ T_SATA0_AHCI_HBA_CAP_BKDR_SUPP_PM); >+ writel(val, tegra->sata_regs + SCFG_OFFSET + >+T_SATA0_AHCI_HBA_CAP_BKDR); >+ >+ /* SATA Second Level Clock Gating configuration >+ * Enabling Gating of Tx/Rx clocks and driving Pad IDDQ and Lane >+ * IDDQ Signals >+ */ >+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_35); >+ val &= ~T_SATA0_CFG_35_IDP_INDEX_MASK; >+ val |= T_SATA0_CFG_35_IDP_INDEX; >+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_35); >+ >+ val = T_SATA0_AHCI_IDP1_DATA; >+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_AHCI_IDP1); >+ >+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_PHY_1); >+ val |= (T_SATA0_CFG_PHY_1_PADS_IDDQ_EN | >+ T_SATA0_CFG_PHY_1_PAD_PLL_IDDQ_EN); >+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_PHY_1); >+ >+ /* >+ * Indicate Sata only has the capability to enter DevSleep >+ * from slumber link. >+ */ >+ >+ val = readl(tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0); >+ val |= SATA_AUX_MISC_CNTL_1_0_DESO_SUPPORT; >+ writel(val, tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0); >+ >+ /* Enabling IPFS Clock Gating */ >+ val = readl(tegra->sata_regs + SATA_CONFIGURATION_0); >+ val &= ~SATA_CONFIGURATION_0_CLK_OVERRIDE; >+ writel(val, tegra->sata_regs + SATA_CONFIGURATION_0); > >- /* Unmask SATA interrupts */ >+ tegra_ahci_handle_quirks(hpriv); > > val = readl(tegra->sata_regs + SATA_INTR_MASK); > val |= SATA_INTR_MASK_IP_INT_MASK; >@@ -278,7 +456,7 @@ static struct ata_port_operations ahci_tegra_port_ops = >{ > .host_stop = tegra_ahci_host_stop, > }; > >-static const struct ata_port_info ahci_tegra_port_info = { >+static struct ata_port_info ahci_tegra_port_info = { > .flags = AHCI_FLAG_COMMON, > .pio_mask = ATA_PIO4, > .udma_mask = ATA_UDMA6, >@@ -286,7 +464,14 @@ static const struct ata_port_info ahci_tegra_port_info = >{ }; > > static const struct of_device_id tegra_ahci_of_match[] = { >- { .compatible = "nvidia,tegra124-ahci" }, >+ { >+ .compatible = "nvidia,tegra124-ahci", >+ .data = &tegra124_ahci_soc_data >+ }, >+ { >+ .compatible = "nvidia,tegra210-ahci", >+ .data = &tegra210_ahci_soc_data >+ }, > {} > }; > MODULE_DEVICE_TABLE(of, tegra_ahci_of_match); @@ -295,12 +480,27 @@ >static struct scsi_host_template ahci_platform_sht = { > AHCI_SHT(DRV_NAME), > }; > >+static void tegra_ahci_handle_quirks(struct ahci_host_priv *hpriv) { >+ struct tegra_ahci_priv *tegra = hpriv->plat_data; >+ u32 val; >+ >+ if (tegra->soc_data->quirks & NO_DEVSLP) { >+ val = readl(tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0); >+ val &= ~SATA_AUX_MISC_CNTL_1_0_SDS_SUPPORT; >+ writel(val, tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0); >+ } else if (tegra->soc_data->quirks & NO_DIPM) { >+ ahci_tegra_port_info.flags |= ATA_FLAG_NO_DIPM; >+ } >+} >+ > static int tegra_ahci_probe(struct platform_device *pdev) { > struct ahci_host_priv *hpriv; > struct tegra_ahci_priv *tegra; > struct resource *res; > int ret; >+ unsigned int i; > > hpriv = ahci_platform_get_resources(pdev); > if (IS_ERR(hpriv)) >@@ -311,13 +511,18 @@ static int tegra_ahci_probe(struct platform_device >*pdev) > return -ENOMEM; > > hpriv->plat_data = tegra; >- > tegra->pdev = pdev; >+ tegra->soc_data = >+ (struct tegra_ahci_soc *)of_device_get_match_data(&pdev->dev); > > res = platform_get_resource(pdev, IORESOURCE_MEM, 1); > tegra->sata_regs = devm_ioremap_resource(&pdev->dev, res); > if (IS_ERR(tegra->sata_regs)) > return PTR_ERR(tegra->sata_regs); >+ res = platform_get_resource(pdev, IORESOURCE_MEM, 2); >+ tegra->sata_aux_regs = devm_ioremap_resource(&pdev->dev, res); >+ if (IS_ERR(tegra->sata_aux_regs)) >+ return PTR_ERR(tegra->sata_aux_regs); > > tegra->sata_rst = devm_reset_control_get(&pdev->dev, "sata"); > if (IS_ERR(tegra->sata_rst)) { >@@ -343,13 +548,17 @@ static int tegra_ahci_probe(struct platform_device >*pdev) > return PTR_ERR(tegra->sata_clk); > } > >- tegra->supplies[0].supply = "avdd"; >- tegra->supplies[1].supply = "hvdd"; >- tegra->supplies[2].supply = "vddio"; >- tegra->supplies[3].supply = "target-5v"; >- tegra->supplies[4].supply = "target-12v"; >+ tegra->supplies = devm_kcalloc(&pdev->dev, >+ tegra->soc_data->num_supplies, >+ sizeof(*tegra->supplies), GFP_KERNEL); >+ if (!tegra->supplies) >+ return -ENOMEM; >+ >+ for (i = 0; i < tegra->soc_data->num_supplies; i++) >+ tegra->supplies[i].supply = tegra->soc_data->supply_names[i]; > >- ret = devm_regulator_bulk_get(&pdev->dev, ARRAY_SIZE(tegra- >>supplies), >+ ret = devm_regulator_bulk_get(&pdev->dev, >+ tegra->soc_data->num_supplies, > tegra->supplies); > if (ret) { > dev_err(&pdev->dev, "Failed to get regulators\n"); @@ -385,5 >+594,5 @@ static struct platform_driver tegra_ahci_driver = { >module_platform_driver(tegra_ahci_driver); > > MODULE_AUTHOR("Mikko Perttunen <mperttunen-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>"); >-MODULE_DESCRIPTION("Tegra124 AHCI SATA driver"); >+MODULE_DESCRIPTION("Tegra AHCI SATA driver"); > MODULE_LICENSE("GPL v2"); >-- >2.1.4 ^ permalink raw reply [flat|nested] 14+ messages in thread
[parent not found: <c3457c8e12b0402293bdea825883277f-7W72rfoJkVnYuxH7O460wFaTQe2KTcn/@public.gmane.org>]
* Re: [PATCH V3 1/3] ata: ahci_tegra: Add AHCI support for tegra210 [not found] ` <c3457c8e12b0402293bdea825883277f-7W72rfoJkVnYuxH7O460wFaTQe2KTcn/@public.gmane.org> @ 2017-05-14 11:18 ` Mikko Perttunen [not found] ` <3dfdc451-794a-832e-4985-ac56d7e1843e-/1wQRMveznE@public.gmane.org> 0 siblings, 1 reply; 14+ messages in thread From: Mikko Perttunen @ 2017-05-14 11:18 UTC (permalink / raw) To: Preetham Chandru, thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org Cc: tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Laxman Dewangan, preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, Venu Byravarasu, Pavan Kunapuli, linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org On 05/12/2017 12:55 PM, Preetham Chandru wrote: > +CC linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org > >> -----Original Message----- >> From: Preetham Chandru >> Sent: Friday, May 12, 2017 3:04 PM >> To: thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org >> Cc: tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; Laxman Dewangan >> <ldewangan-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; Venu Byravarasu >> <vbyravarasu-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; Pavan Kunapuli <pkunapuli-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; Preetham >> Chandru <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >> Subject: [PATCH V3 1/3] ata: ahci_tegra: Add AHCI support for tegra210 >> >> From: Preetham Chandru R <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >> >> 1. Move tegra124 specifics to tegra124_ahci_init. >> 2. Separate the regulators needed for tegra124 and tegra210. >> 3. Disable DIPM and Devslp for t210 and t124 as there are known issues >> >> Signed-off-by: Preetham Chandru R <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >> --- >> v3: >> * Remove inline functions for read/write and modify to >> SATA, SATA Config and SATA Aux registers. >> * Add code to disable DIPM and DevSlp for t210 and t124 >> v2: >> * Fix indentation issues >> * Move the change to disable DIPM, HIPM, DevSlp, partial, >> slumber and NCQ into a separate patch >> --- >> drivers/ata/ahci_tegra.c | 377 ++++++++++++++++++++++++++++++++++++------- >> ---- >> 1 file changed, 293 insertions(+), 84 deletions(-) >> >> diff --git a/drivers/ata/ahci_tegra.c b/drivers/ata/ahci_tegra.c index >> 3a62eb2..cd581a6 100644 >> --- a/drivers/ata/ahci_tegra.c >> +++ b/drivers/ata/ahci_tegra.c >> @@ -34,7 +34,8 @@ >> #define DRV_NAME "tegra-ahci" >> >> #define SATA_CONFIGURATION_0 0x180 >> -#define SATA_CONFIGURATION_EN_FPCI BIT(0) >> +#define SATA_CONFIGURATION_0_EN_FPCI BIT(0) >> +#define SATA_CONFIGURATION_0_CLK_OVERRIDE BIT(31) >> >> #define SCFG_OFFSET 0x1000 >> >> @@ -45,17 +46,55 @@ >> #define T_SATA0_CFG_1_SERR BIT(8) >> >> #define T_SATA0_CFG_9 0x24 >> -#define T_SATA0_CFG_9_BASE_ADDRESS_SHIFT 13 >> +#define T_SATA0_CFG_9_BASE_ADDRESS 0x40020000 >> >> #define SATA_FPCI_BAR5 0x94 >> -#define SATA_FPCI_BAR5_START_SHIFT 4 >> +#define SATA_FPCI_BAR5_START_MASK (0xfffffff << 4) >> +#define SATA_FPCI_BAR5_START (0x0040020 << >> 4) >> +#define SATA_FPCI_BAR5_ACCESS_TYPE (0x1) >> >> #define SATA_INTR_MASK 0x188 >> #define SATA_INTR_MASK_IP_INT_MASK BIT(16) >> >> +#define T_SATA0_CFG_35 0x94 >> +#define T_SATA0_CFG_35_IDP_INDEX_MASK (0x7ff << 2) >> +#define T_SATA0_CFG_35_IDP_INDEX (0x2a << 2) >> + >> +#define T_SATA0_AHCI_IDP1 0x98 >> +#define T_SATA0_AHCI_IDP1_DATA (0x400040) >> + >> +#define T_SATA0_CFG_PHY_1 0x12c >> +#define T_SATA0_CFG_PHY_1_PADS_IDDQ_EN BIT(23) >> +#define T_SATA0_CFG_PHY_1_PAD_PLL_IDDQ_EN BIT(22) >> + >> +#define T_SATA0_NVOOB 0x114 >> +#define T_SATA0_NVOOB_COMMA_CNT_MASK (0xff << 16) >> +#define T_SATA0_NVOOB_COMMA_CNT (0x07 << 16) >> +#define T_SATA0_NVOOB_SQUELCH_FILTER_MODE_MASK (0x3 << 24) >> +#define T_SATA0_NVOOB_SQUELCH_FILTER_MODE (0x1 << 24) >> +#define T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH_MASK (0x3 << 26) >> +#define T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH (0x3 << 26) >> + >> +#define T_SATA_CFG_PHY_0 0x120 >> +#define T_SATA_CFG_PHY_0_USE_7BIT_ALIGN_DET_FOR_SPD BIT(11) >> +#define T_SATA_CFG_PHY_0_MASK_SQUELCH BIT(24) >> + >> +#define T_SATA0_CFG2NVOOB_2 0x134 >> +#define T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW_MASK (0x1ff >> << 18) >> +#define T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW (0xc << 18) >> + >> #define T_SATA0_AHCI_HBA_CAP_BKDR 0x300 >> +#define T_SATA0_AHCI_HBA_CAP_BKDR_PARTIAL_ST_CAP BIT(13) >> +#define T_SATA0_AHCI_HBA_CAP_BKDR_SLUMBER_ST_CAP BIT(14) >> +#define T_SATA0_AHCI_HBA_CAP_BKDR_SALP BIT(26) >> +#define T_SATA0_AHCI_HBA_CAP_BKDR_SUPP_PM BIT(17) >> +#define T_SATA0_AHCI_HBA_CAP_BKDR_SNCQ BIT(30) >> >> #define T_SATA0_BKDOOR_CC 0x4a4 >> +#define T_SATA0_BKDOOR_CC_CLASS_CODE_MASK (0xffff << 16) >> +#define T_SATA0_BKDOOR_CC_CLASS_CODE (0x0106 << 16) >> +#define T_SATA0_BKDOOR_CC_PROG_IF_MASK (0xff << 8) >> +#define T_SATA0_BKDOOR_CC_PROG_IF (0x01 << 8) >> >> #define T_SATA0_CFG_SATA 0x54c >> #define T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN BIT(12) >> @@ -82,9 +121,35 @@ >> #define T_SATA0_CHX_PHY_CTRL11 0x6d0 >> #define T_SATA0_CHX_PHY_CTRL11_GEN2_RX_EQ (0x2800 << 16) >> >> +#define T_SATA0_CHX_PHY_CTRL17_0 0x6e8 >> +#define T_SATA0_CHX_PHY_CTRL17_0_RX_EQ_CTRL_L_GEN1 0x55010000 >> +#define T_SATA0_CHX_PHY_CTRL18_0 0x6ec >> +#define T_SATA0_CHX_PHY_CTRL18_0_RX_EQ_CTRL_L_GEN2 0x55010000 >> +#define T_SATA0_CHX_PHY_CTRL20_0 0x6f4 >> +#define T_SATA0_CHX_PHY_CTRL20_0_RX_EQ_CTRL_H_GEN1 0x1 >> +#define T_SATA0_CHX_PHY_CTRL21_0 0x6f8 >> +#define T_SATA0_CHX_PHY_CTRL21_0_RX_EQ_CTRL_H_GEN2 0x1 >> + >> +/* AUX Registers */ >> +#define SATA_AUX_MISC_CNTL_1_0 0x8 >> +#define SATA_AUX_MISC_CNTL_1_0_DEVSLP_OVERRIDE BIT(17) >> +#define SATA_AUX_MISC_CNTL_1_0_SDS_SUPPORT BIT(13) >> +#define SATA_AUX_MISC_CNTL_1_0_DESO_SUPPORT BIT(15) >> + >> +#define SATA_AUX_RX_STAT_INT_0 0xc >> +#define SATA_AUX_RX_STAT_INT_0_SATA_DEVSLP BIT(7) >> + >> +#define SATA_AUX_SPARE_CFG0_0 0x18 >> +#define SATA_AUX_SPARE_CFG0_0_MDAT_TIMER_AFTER_PG_VALID BIT(14) >> + >> #define FUSE_SATA_CALIB 0x124 >> #define FUSE_SATA_CALIB_MASK 0x3 >> >> +enum { >> + NO_DEVSLP = (1 << 0), >> + NO_DIPM = (1 << 1), >> +}; >> + >> struct sata_pad_calibration { >> u8 gen1_tx_amp; >> u8 gen1_tx_peak; >> @@ -99,15 +164,89 @@ static const struct sata_pad_calibration >> tegra124_pad_calibration[] = { >> {0x14, 0x0e, 0x1a, 0x0e}, >> }; >> >> +struct tegra_ahci_ops { >> + int (*init)(struct ahci_host_priv *); >> +}; >> + >> +struct tegra_ahci_soc { >> + const char *const *supply_names; >> + u32 num_supplies; >> + u32 quirks; >> + struct tegra_ahci_ops ops; >> +}; >> + >> struct tegra_ahci_priv { >> struct platform_device *pdev; >> void __iomem *sata_regs; >> + void __iomem *sata_aux_regs; >> struct reset_control *sata_rst; >> struct reset_control *sata_oob_rst; >> struct reset_control *sata_cold_rst; >> /* Needs special handling, cannot use ahci_platform */ >> struct clk *sata_clk; >> - struct regulator_bulk_data supplies[5]; >> + struct regulator_bulk_data *supplies; >> + struct tegra_ahci_soc *soc_data; >> +}; >> + >> +static const char *const tegra124_supply_names[] = { >> + "avdd", "hvdd", "vddio", "target-5v", "target-12v" >> +}; >> + >> +static int tegra124_ahci_init(struct ahci_host_priv *hpriv) { >> + struct tegra_ahci_priv *tegra = hpriv->plat_data; >> + struct sata_pad_calibration calib; >> + int ret; >> + u32 val; >> + >> + /* Pad calibration */ >> + ret = tegra_fuse_readl(FUSE_SATA_CALIB, &val); >> + if (ret) >> + return ret; >> + >> + calib = tegra124_pad_calibration[val & FUSE_SATA_CALIB_MASK]; >> + >> + writel(BIT(0), tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX); >> + >> + val = readl(tegra->sata_regs + >> + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN1); >> + val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_MASK; >> + val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_MASK; >> + val |= calib.gen1_tx_amp << >> T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT; >> + val |= calib.gen1_tx_peak << >> T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT; >> + writel(val, tegra->sata_regs + SCFG_OFFSET + >> + T_SATA0_CHX_PHY_CTRL1_GEN1); >> + >> + val = readl(tegra->sata_regs + >> + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN2); >> + val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_AMP_MASK; >> + val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_PEAK_MASK; >> + val |= calib.gen2_tx_amp << >> T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT; >> + val |= calib.gen2_tx_peak << >> T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT; >> + writel(val, tegra->sata_regs + SCFG_OFFSET + >> + T_SATA0_CHX_PHY_CTRL1_GEN2); >> + >> + writel(T_SATA0_CHX_PHY_CTRL11_GEN2_RX_EQ, >> + tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL11); >> + writel(T_SATA0_CHX_PHY_CTRL2_CDR_CNTL_GEN1, >> + tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL2); >> + >> + writel(0, tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX); >> + >> + return 0; >> +} >> + >> +static const struct tegra_ahci_soc tegra124_ahci_soc_data = { >> + .supply_names = tegra124_supply_names, >> + .num_supplies = ARRAY_SIZE(tegra124_supply_names), >> + .quirks = NO_DIPM | NO_DEVSLP, >> + .ops = { >> + .init = tegra124_ahci_init, >> + }, Indent this "}," one tab less (i.e. to same level as '.ops') >> +}; >> + >> +static const struct tegra_ahci_soc tegra210_ahci_soc_data = { >> + .quirks = NO_DIPM | NO_DEVSLP, >> }; >> >> static int tegra_ahci_power_on(struct ahci_host_priv *hpriv) @@ -115,7 +254,7 >> @@ static int tegra_ahci_power_on(struct ahci_host_priv *hpriv) >> struct tegra_ahci_priv *tegra = hpriv->plat_data; >> int ret; >> >> - ret = regulator_bulk_enable(ARRAY_SIZE(tegra->supplies), >> + ret = regulator_bulk_enable(tegra->soc_data->num_supplies, >> tegra->supplies); >> if (ret) >> return ret; >> @@ -144,8 +283,7 @@ static int tegra_ahci_power_on(struct ahci_host_priv >> *hpriv) >> tegra_powergate_power_off(TEGRA_POWERGATE_SATA); >> >> disable_regulators: >> - regulator_bulk_disable(ARRAY_SIZE(tegra->supplies), tegra->supplies); >> - >> + regulator_bulk_disable(tegra->soc_data->num_supplies, >> +tegra->supplies); Indent this. >> return ret; >> } >> >> @@ -162,97 +300,137 @@ static void tegra_ahci_power_off(struct >> ahci_host_priv *hpriv) >> clk_disable_unprepare(tegra->sata_clk); >> tegra_powergate_power_off(TEGRA_POWERGATE_SATA); >> >> - regulator_bulk_disable(ARRAY_SIZE(tegra->supplies), tegra->supplies); >> + regulator_bulk_disable(tegra->soc_data->num_supplies, >> +tegra->supplies); And this >> } >> >> static int tegra_ahci_controller_init(struct ahci_host_priv *hpriv) { >> struct tegra_ahci_priv *tegra = hpriv->plat_data; >> int ret; >> - unsigned int val; >> - struct sata_pad_calibration calib; >> + u32 val; >> >> ret = tegra_ahci_power_on(hpriv); >> - if (ret) { >> - dev_err(&tegra->pdev->dev, >> - "failed to power on AHCI controller: %d\n", ret); >> + if (ret) >> return ret; >> - } >> >> + /* >> + * Program the following SATA IPFS registers Extra space between "following" and "SATA" >> + * to allow SW accesses to SATA's MMIO Register Perhaps say "register range" >> + */ >> + val = readl(tegra->sata_regs + SATA_FPCI_BAR5); >> + val &= ~(SATA_FPCI_BAR5_START_MASK | >> SATA_FPCI_BAR5_ACCESS_TYPE); >> + val |= SATA_FPCI_BAR5_START | SATA_FPCI_BAR5_ACCESS_TYPE; >> + writel(val, tegra->sata_regs + SATA_FPCI_BAR5); >> + >> + /* Program the following SATA IPFS register to enable the SATA */ >> val = readl(tegra->sata_regs + SATA_CONFIGURATION_0); >> - val |= SATA_CONFIGURATION_EN_FPCI; >> + val |= SATA_CONFIGURATION_0_EN_FPCI; >> writel(val, tegra->sata_regs + SATA_CONFIGURATION_0); >> >> - /* Pad calibration */ >> - >> - ret = tegra_fuse_readl(FUSE_SATA_CALIB, &val); >> - if (ret) { >> - dev_err(&tegra->pdev->dev, >> - "failed to read calibration fuse: %d\n", ret); >> - return ret; >> - } >> - >> - calib = tegra124_pad_calibration[val & FUSE_SATA_CALIB_MASK]; >> - >> - writel(BIT(0), tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX); >> - >> - val = readl(tegra->sata_regs + >> - SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN1); >> - val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_MASK; >> - val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_MASK; >> - val |= calib.gen1_tx_amp << >> - T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT; >> - val |= calib.gen1_tx_peak << >> - T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT; >> - writel(val, tegra->sata_regs + SCFG_OFFSET + >> - T_SATA0_CHX_PHY_CTRL1_GEN1); >> - >> - val = readl(tegra->sata_regs + >> - SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN2); >> - val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_AMP_MASK; >> - val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_PEAK_MASK; >> - val |= calib.gen2_tx_amp << >> - T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT; >> - val |= calib.gen2_tx_peak << >> - T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT; >> - writel(val, tegra->sata_regs + SCFG_OFFSET + >> - T_SATA0_CHX_PHY_CTRL1_GEN2); >> - >> - writel(T_SATA0_CHX_PHY_CTRL11_GEN2_RX_EQ, >> - tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL11); >> - writel(T_SATA0_CHX_PHY_CTRL2_CDR_CNTL_GEN1, >> - tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL2); >> - >> - writel(0, tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX); >> - >> - /* Program controller device ID */ >> + /* Electrical settings for better link stability */ >> + val = T_SATA0_CHX_PHY_CTRL17_0_RX_EQ_CTRL_L_GEN1; >> + writel(val, tegra->sata_regs + SCFG_OFFSET + >> T_SATA0_CHX_PHY_CTRL17_0); >> + val = T_SATA0_CHX_PHY_CTRL18_0_RX_EQ_CTRL_L_GEN2; >> + writel(val, tegra->sata_regs + SCFG_OFFSET + >> T_SATA0_CHX_PHY_CTRL18_0); >> + val = T_SATA0_CHX_PHY_CTRL20_0_RX_EQ_CTRL_H_GEN1; >> + writel(val, tegra->sata_regs + SCFG_OFFSET + >> T_SATA0_CHX_PHY_CTRL20_0); >> + val = T_SATA0_CHX_PHY_CTRL21_0_RX_EQ_CTRL_H_GEN2; >> + writel(val, tegra->sata_regs + SCFG_OFFSET + >> +T_SATA0_CHX_PHY_CTRL21_0); Indent >> + >> + /* For SQUELCH Filter & Gen3 drive getting detected as Gen1 drive */ >> + >> + val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA_CFG_PHY_0); >> + val |= T_SATA_CFG_PHY_0_MASK_SQUELCH; >> + val &= ~T_SATA_CFG_PHY_0_USE_7BIT_ALIGN_DET_FOR_SPD; >> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA_CFG_PHY_0); >> + >> + val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_NVOOB); >> + val &= ~(T_SATA0_NVOOB_COMMA_CNT_MASK | >> + T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH_MASK | >> + T_SATA0_NVOOB_SQUELCH_FILTER_MODE_MASK); >> + val |= (T_SATA0_NVOOB_COMMA_CNT | >> + T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH | >> + T_SATA0_NVOOB_SQUELCH_FILTER_MODE); >> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_NVOOB); >> + >> + /* >> + * Change CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW from 83.3 ns to >> 58.8ns >> + */ >> + val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG2NVOOB_2); >> + val &= ~T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW_MASK; >> + val |= T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW; >> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG2NVOOB_2); >> + >> + if (tegra->soc_data->ops.init) >> + tegra->soc_data->ops.init(hpriv); >> + >> + /* >> + * Program the following SATA configuration registers >> + * to initialize SATA >> + */ >> + val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1); >> + val |= (T_SATA0_CFG_1_IO_SPACE | T_SATA0_CFG_1_MEMORY_SPACE | >> + T_SATA0_CFG_1_BUS_MASTER | T_SATA0_CFG_1_SERR); >> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1); >> + val = T_SATA0_CFG_9_BASE_ADDRESS; >> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_9); >> >> + /* Program Class Code and Programming interface for SATA */ >> val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA); >> val |= T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN; >> writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA); >> >> - writel(0x01060100, tegra->sata_regs + SCFG_OFFSET + >> T_SATA0_BKDOOR_CC); >> + val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_BKDOOR_CC); >> + val &= >> + ~(T_SATA0_BKDOOR_CC_CLASS_CODE_MASK | >> + T_SATA0_BKDOOR_CC_PROG_IF_MASK); >> + val |= T_SATA0_BKDOOR_CC_CLASS_CODE | >> T_SATA0_BKDOOR_CC_PROG_IF; >> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_BKDOOR_CC); >> >> val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA); >> val &= ~T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN; >> writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA); >> >> - /* Enable IO & memory access, bus master mode */ >> - >> - val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1); >> - val |= T_SATA0_CFG_1_IO_SPACE | T_SATA0_CFG_1_MEMORY_SPACE | >> - T_SATA0_CFG_1_BUS_MASTER | T_SATA0_CFG_1_SERR; >> - writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1); >> - >> - /* Program SATA MMIO */ >> - >> - writel(0x10000 << SATA_FPCI_BAR5_START_SHIFT, >> - tegra->sata_regs + SATA_FPCI_BAR5); >> - >> - writel(0x08000 << T_SATA0_CFG_9_BASE_ADDRESS_SHIFT, >> - tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_9); >> + /* Enabling LPM capabilities through Backdoor Programming */ >> + val = readl(tegra->sata_regs + SCFG_OFFSET + >> T_SATA0_AHCI_HBA_CAP_BKDR); >> + val |= (T_SATA0_AHCI_HBA_CAP_BKDR_PARTIAL_ST_CAP | >> + T_SATA0_AHCI_HBA_CAP_BKDR_SLUMBER_ST_CAP | >> + T_SATA0_AHCI_HBA_CAP_BKDR_SALP | >> + T_SATA0_AHCI_HBA_CAP_BKDR_SUPP_PM); >> + writel(val, tegra->sata_regs + SCFG_OFFSET + >> +T_SATA0_AHCI_HBA_CAP_BKDR); >> + >> + /* SATA Second Level Clock Gating configuration >> + * Enabling Gating of Tx/Rx clocks and driving Pad IDDQ and Lane >> + * IDDQ Signals >> + */ >> + val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_35); >> + val &= ~T_SATA0_CFG_35_IDP_INDEX_MASK; >> + val |= T_SATA0_CFG_35_IDP_INDEX; >> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_35); >> + >> + val = T_SATA0_AHCI_IDP1_DATA; >> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_AHCI_IDP1); >> + >> + val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_PHY_1); >> + val |= (T_SATA0_CFG_PHY_1_PADS_IDDQ_EN | >> + T_SATA0_CFG_PHY_1_PAD_PLL_IDDQ_EN); >> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_PHY_1); >> + >> + /* >> + * Indicate Sata only has the capability to enter DevSleep Stray space in front >> + * from slumber link. >> + */ >> + >> + val = readl(tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0); >> + val |= SATA_AUX_MISC_CNTL_1_0_DESO_SUPPORT; >> + writel(val, tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0); >> + >> + /* Enabling IPFS Clock Gating */ >> + val = readl(tegra->sata_regs + SATA_CONFIGURATION_0); >> + val &= ~SATA_CONFIGURATION_0_CLK_OVERRIDE; >> + writel(val, tegra->sata_regs + SATA_CONFIGURATION_0); >> >> - /* Unmask SATA interrupts */ >> + tegra_ahci_handle_quirks(hpriv); >> >> val = readl(tegra->sata_regs + SATA_INTR_MASK); >> val |= SATA_INTR_MASK_IP_INT_MASK; >> @@ -278,7 +456,7 @@ static struct ata_port_operations ahci_tegra_port_ops = >> { >> .host_stop = tegra_ahci_host_stop, >> }; >> >> -static const struct ata_port_info ahci_tegra_port_info = { >> +static struct ata_port_info ahci_tegra_port_info = { >> .flags = AHCI_FLAG_COMMON, >> .pio_mask = ATA_PIO4, >> .udma_mask = ATA_UDMA6, >> @@ -286,7 +464,14 @@ static const struct ata_port_info ahci_tegra_port_info = >> { }; >> >> static const struct of_device_id tegra_ahci_of_match[] = { >> - { .compatible = "nvidia,tegra124-ahci" }, >> + { >> + .compatible = "nvidia,tegra124-ahci", >> + .data = &tegra124_ahci_soc_data >> + }, >> + { >> + .compatible = "nvidia,tegra210-ahci", >> + .data = &tegra210_ahci_soc_data >> + }, >> {} >> }; >> MODULE_DEVICE_TABLE(of, tegra_ahci_of_match); @@ -295,12 +480,27 @@ >> static struct scsi_host_template ahci_platform_sht = { >> AHCI_SHT(DRV_NAME), >> }; >> >> +static void tegra_ahci_handle_quirks(struct ahci_host_priv *hpriv) { >> + struct tegra_ahci_priv *tegra = hpriv->plat_data; >> + u32 val; >> + >> + if (tegra->soc_data->quirks & NO_DEVSLP) { >> + val = readl(tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0); >> + val &= ~SATA_AUX_MISC_CNTL_1_0_SDS_SUPPORT; >> + writel(val, tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0); >> + } else if (tegra->soc_data->quirks & NO_DIPM) { I don't think this should be 'else if', but just two separate regular 'if's? >> + ahci_tegra_port_info.flags |= ATA_FLAG_NO_DIPM; Looking at the downstream device trees, it looks like DIPM and DEVSLP are still disabled for Tegra186 - so why don't we just hardcode these quirks, by always writing the MISC_CNTL_1_0 register and just adding ATA_FLAG_NO_DIPM to ahci_tegra_port_info's static definition. >> + } >> +} >> + >> static int tegra_ahci_probe(struct platform_device *pdev) { >> struct ahci_host_priv *hpriv; >> struct tegra_ahci_priv *tegra; >> struct resource *res; >> int ret; >> + unsigned int i; >> >> hpriv = ahci_platform_get_resources(pdev); >> if (IS_ERR(hpriv)) >> @@ -311,13 +511,18 @@ static int tegra_ahci_probe(struct platform_device >> *pdev) >> return -ENOMEM; >> >> hpriv->plat_data = tegra; >> - >> tegra->pdev = pdev; >> + tegra->soc_data = >> + (struct tegra_ahci_soc *)of_device_get_match_data(&pdev->dev); >> >> res = platform_get_resource(pdev, IORESOURCE_MEM, 1); >> tegra->sata_regs = devm_ioremap_resource(&pdev->dev, res); >> if (IS_ERR(tegra->sata_regs)) >> return PTR_ERR(tegra->sata_regs); >> + res = platform_get_resource(pdev, IORESOURCE_MEM, 2); >> + tegra->sata_aux_regs = devm_ioremap_resource(&pdev->dev, res); >> + if (IS_ERR(tegra->sata_aux_regs)) >> + return PTR_ERR(tegra->sata_aux_regs); Requiring aux_regs would break backwards compatibility for Tegra124 device trees. We will have to keep aux_regs optional for Tegra124, and skip writes to them if they are not available. >> >> tegra->sata_rst = devm_reset_control_get(&pdev->dev, "sata"); >> if (IS_ERR(tegra->sata_rst)) { >> @@ -343,13 +548,17 @@ static int tegra_ahci_probe(struct platform_device >> *pdev) >> return PTR_ERR(tegra->sata_clk); >> } >> >> - tegra->supplies[0].supply = "avdd"; >> - tegra->supplies[1].supply = "hvdd"; >> - tegra->supplies[2].supply = "vddio"; >> - tegra->supplies[3].supply = "target-5v"; >> - tegra->supplies[4].supply = "target-12v"; >> + tegra->supplies = devm_kcalloc(&pdev->dev, >> + tegra->soc_data->num_supplies, >> + sizeof(*tegra->supplies), GFP_KERNEL); >> + if (!tegra->supplies) >> + return -ENOMEM; >> + >> + for (i = 0; i < tegra->soc_data->num_supplies; i++) >> + tegra->supplies[i].supply = tegra->soc_data->supply_names[i]; >> >> - ret = devm_regulator_bulk_get(&pdev->dev, ARRAY_SIZE(tegra- >>> supplies), >> + ret = devm_regulator_bulk_get(&pdev->dev, >> + tegra->soc_data->num_supplies, >> tegra->supplies); >> if (ret) { >> dev_err(&pdev->dev, "Failed to get regulators\n"); @@ -385,5 >> +594,5 @@ static struct platform_driver tegra_ahci_driver = { >> module_platform_driver(tegra_ahci_driver); >> >> MODULE_AUTHOR("Mikko Perttunen <mperttunen-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>"); >> -MODULE_DESCRIPTION("Tegra124 AHCI SATA driver"); >> +MODULE_DESCRIPTION("Tegra AHCI SATA driver"); >> MODULE_LICENSE("GPL v2"); >> -- >> 2.1.4 > > -- > To unsubscribe from this list: send the line "unsubscribe linux-tegra" in > the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > Thanks for posting! Mikko ^ permalink raw reply [flat|nested] 14+ messages in thread
[parent not found: <3dfdc451-794a-832e-4985-ac56d7e1843e-/1wQRMveznE@public.gmane.org>]
* RE: [PATCH V3 1/3] ata: ahci_tegra: Add AHCI support for tegra210 [not found] ` <3dfdc451-794a-832e-4985-ac56d7e1843e-/1wQRMveznE@public.gmane.org> @ 2017-05-24 5:44 ` Preetham Chandru [not found] ` <db35147839414c609a5dc2cde44dd998-gjLx+0+SZqK6sJks/06JalaTQe2KTcn/@public.gmane.org> 0 siblings, 1 reply; 14+ messages in thread From: Preetham Chandru @ 2017-05-24 5:44 UTC (permalink / raw) To: Mikko Perttunen, thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org Cc: linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Laxman Dewangan, preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, Venu Byravarasu, Pavan Kunapuli, linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org >-----Original Message----- >From: Mikko Perttunen [mailto:cyndis-/1wQRMveznE@public.gmane.org] >Sent: Sunday, May 14, 2017 4:49 PM >To: Preetham Chandru <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; >tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org >Cc: tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; Laxman Dewangan ><ldewangan-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; Venu Byravarasu ><vbyravarasu-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; Pavan Kunapuli <pkunapuli-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; linux- >tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org >Subject: Re: [PATCH V3 1/3] ata: ahci_tegra: Add AHCI support for tegra210 > >On 05/12/2017 12:55 PM, Preetham Chandru wrote: >> +CC linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org >> >>> -----Original Message----- >>> From: Preetham Chandru >>> Sent: Friday, May 12, 2017 3:04 PM >>> To: thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org >>> Cc: tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; Laxman Dewangan >>> <ldewangan-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; Venu Byravarasu >>> <vbyravarasu-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; Pavan Kunapuli <pkunapuli-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; >>> Preetham Chandru <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >>> Subject: [PATCH V3 1/3] ata: ahci_tegra: Add AHCI support for >>> tegra210 >>> >>> From: Preetham Chandru R <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >>> >>> 1. Move tegra124 specifics to tegra124_ahci_init. >>> 2. Separate the regulators needed for tegra124 and tegra210. >>> 3. Disable DIPM and Devslp for t210 and t124 as there are known >>> issues >>> >>> Signed-off-by: Preetham Chandru R <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >>> --- >>> v3: >>> * Remove inline functions for read/write and modify to SATA, SATA >>> Config and SATA Aux registers. >>> * Add code to disable DIPM and DevSlp for t210 and t124 >>> v2: >>> * Fix indentation issues >>> * Move the change to disable DIPM, HIPM, DevSlp, partial, slumber >>> and NCQ into a separate patch >>> --- >>> drivers/ata/ahci_tegra.c | 377 >>> ++++++++++++++++++++++++++++++++++++------- >>> ---- >>> 1 file changed, 293 insertions(+), 84 deletions(-) >>> >>> diff --git a/drivers/ata/ahci_tegra.c b/drivers/ata/ahci_tegra.c >>> index >>> 3a62eb2..cd581a6 100644 >>> --- a/drivers/ata/ahci_tegra.c >>> +++ b/drivers/ata/ahci_tegra.c >>> @@ -34,7 +34,8 @@ >>> #define DRV_NAME "tegra-ahci" >>> >>> #define SATA_CONFIGURATION_0 0x180 >>> -#define SATA_CONFIGURATION_EN_FPCI BIT(0) >>> +#define SATA_CONFIGURATION_0_EN_FPCI BIT(0) >>> +#define SATA_CONFIGURATION_0_CLK_OVERRIDE BIT(31) >>> >>> #define SCFG_OFFSET 0x1000 >>> >>> @@ -45,17 +46,55 @@ >>> #define T_SATA0_CFG_1_SERR BIT(8) >>> >>> #define T_SATA0_CFG_9 0x24 >>> -#define T_SATA0_CFG_9_BASE_ADDRESS_SHIFT 13 >>> +#define T_SATA0_CFG_9_BASE_ADDRESS 0x40020000 >>> >>> #define SATA_FPCI_BAR5 0x94 >>> -#define SATA_FPCI_BAR5_START_SHIFT 4 >>> +#define SATA_FPCI_BAR5_START_MASK (0xfffffff << 4) >>> +#define SATA_FPCI_BAR5_START (0x0040020 << >>> 4) >>> +#define SATA_FPCI_BAR5_ACCESS_TYPE (0x1) >>> >>> #define SATA_INTR_MASK 0x188 >>> #define SATA_INTR_MASK_IP_INT_MASK BIT(16) >>> >>> +#define T_SATA0_CFG_35 0x94 >>> +#define T_SATA0_CFG_35_IDP_INDEX_MASK (0x7ff ><< 2) >>> +#define T_SATA0_CFG_35_IDP_INDEX (0x2a << 2) >>> + >>> +#define T_SATA0_AHCI_IDP1 0x98 >>> +#define T_SATA0_AHCI_IDP1_DATA (0x400040) >>> + >>> +#define T_SATA0_CFG_PHY_1 0x12c >>> +#define T_SATA0_CFG_PHY_1_PADS_IDDQ_EN BIT(23) >>> +#define T_SATA0_CFG_PHY_1_PAD_PLL_IDDQ_EN BIT(22) >>> + >>> +#define T_SATA0_NVOOB 0x114 >>> +#define T_SATA0_NVOOB_COMMA_CNT_MASK (0xff << 16) >>> +#define T_SATA0_NVOOB_COMMA_CNT (0x07 << 16) >>> +#define T_SATA0_NVOOB_SQUELCH_FILTER_MODE_MASK (0x3 << 24) >>> +#define T_SATA0_NVOOB_SQUELCH_FILTER_MODE (0x1 << 24) >>> +#define T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH_MASK (0x3 << 26) >>> +#define T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH (0x3 << 26) >>> + >>> +#define T_SATA_CFG_PHY_0 0x120 >>> +#define T_SATA_CFG_PHY_0_USE_7BIT_ALIGN_DET_FOR_SPD BIT(11) >>> +#define T_SATA_CFG_PHY_0_MASK_SQUELCH BIT(24) >>> + >>> +#define T_SATA0_CFG2NVOOB_2 0x134 >>> +#define T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW_MASK > (0x1ff >>> << 18) >>> +#define T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW (0xc << >18) >>> + >>> #define T_SATA0_AHCI_HBA_CAP_BKDR 0x300 >>> +#define T_SATA0_AHCI_HBA_CAP_BKDR_PARTIAL_ST_CAP BIT(13) >>> +#define T_SATA0_AHCI_HBA_CAP_BKDR_SLUMBER_ST_CAP BIT(14) >>> +#define T_SATA0_AHCI_HBA_CAP_BKDR_SALP BIT(26) >>> +#define T_SATA0_AHCI_HBA_CAP_BKDR_SUPP_PM BIT(17) >>> +#define T_SATA0_AHCI_HBA_CAP_BKDR_SNCQ BIT(30) >>> >>> #define T_SATA0_BKDOOR_CC 0x4a4 >>> +#define T_SATA0_BKDOOR_CC_CLASS_CODE_MASK (0xffff << 16) >>> +#define T_SATA0_BKDOOR_CC_CLASS_CODE > (0x0106 << 16) >>> +#define T_SATA0_BKDOOR_CC_PROG_IF_MASK (0xff << >8) >>> +#define T_SATA0_BKDOOR_CC_PROG_IF (0x01 << 8) >>> >>> #define T_SATA0_CFG_SATA 0x54c >>> #define T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN BIT(12) >>> @@ -82,9 +121,35 @@ >>> #define T_SATA0_CHX_PHY_CTRL11 0x6d0 >>> #define T_SATA0_CHX_PHY_CTRL11_GEN2_RX_EQ (0x2800 << 16) >>> >>> +#define T_SATA0_CHX_PHY_CTRL17_0 0x6e8 >>> +#define T_SATA0_CHX_PHY_CTRL17_0_RX_EQ_CTRL_L_GEN1 > 0x55010000 >>> +#define T_SATA0_CHX_PHY_CTRL18_0 0x6ec >>> +#define T_SATA0_CHX_PHY_CTRL18_0_RX_EQ_CTRL_L_GEN2 > 0x55010000 >>> +#define T_SATA0_CHX_PHY_CTRL20_0 0x6f4 >>> +#define T_SATA0_CHX_PHY_CTRL20_0_RX_EQ_CTRL_H_GEN1 0x1 >>> +#define T_SATA0_CHX_PHY_CTRL21_0 0x6f8 >>> +#define T_SATA0_CHX_PHY_CTRL21_0_RX_EQ_CTRL_H_GEN2 0x1 >>> + >>> +/* AUX Registers */ >>> +#define SATA_AUX_MISC_CNTL_1_0 0x8 >>> +#define SATA_AUX_MISC_CNTL_1_0_DEVSLP_OVERRIDE BIT(17) >>> +#define SATA_AUX_MISC_CNTL_1_0_SDS_SUPPORT BIT(13) >>> +#define SATA_AUX_MISC_CNTL_1_0_DESO_SUPPORT BIT(15) >>> + >>> +#define SATA_AUX_RX_STAT_INT_0 0xc >>> +#define SATA_AUX_RX_STAT_INT_0_SATA_DEVSLP BIT(7) >>> + >>> +#define SATA_AUX_SPARE_CFG0_0 0x18 >>> +#define SATA_AUX_SPARE_CFG0_0_MDAT_TIMER_AFTER_PG_VALID BIT(14) >>> + >>> #define FUSE_SATA_CALIB 0x124 >>> #define FUSE_SATA_CALIB_MASK 0x3 >>> >>> +enum { >>> + NO_DEVSLP = (1 << 0), >>> + NO_DIPM = (1 << 1), >>> +}; >>> + >>> struct sata_pad_calibration { >>> u8 gen1_tx_amp; >>> u8 gen1_tx_peak; >>> @@ -99,15 +164,89 @@ static const struct sata_pad_calibration >>> tegra124_pad_calibration[] = { >>> {0x14, 0x0e, 0x1a, 0x0e}, >>> }; >>> >>> +struct tegra_ahci_ops { >>> + int (*init)(struct ahci_host_priv *); }; >>> + >>> +struct tegra_ahci_soc { >>> + const char *const *supply_names; >>> + u32 num_supplies; >>> + u32 quirks; >>> + struct tegra_ahci_ops ops; >>> +}; >>> + >>> struct tegra_ahci_priv { >>> struct platform_device *pdev; >>> void __iomem *sata_regs; >>> + void __iomem *sata_aux_regs; >>> struct reset_control *sata_rst; >>> struct reset_control *sata_oob_rst; >>> struct reset_control *sata_cold_rst; >>> /* Needs special handling, cannot use ahci_platform */ >>> struct clk *sata_clk; >>> - struct regulator_bulk_data supplies[5]; >>> + struct regulator_bulk_data *supplies; >>> + struct tegra_ahci_soc *soc_data; >>> +}; >>> + >>> +static const char *const tegra124_supply_names[] = { >>> + "avdd", "hvdd", "vddio", "target-5v", "target-12v" >>> +}; >>> + >>> +static int tegra124_ahci_init(struct ahci_host_priv *hpriv) { >>> + struct tegra_ahci_priv *tegra = hpriv->plat_data; >>> + struct sata_pad_calibration calib; >>> + int ret; >>> + u32 val; >>> + >>> + /* Pad calibration */ >>> + ret = tegra_fuse_readl(FUSE_SATA_CALIB, &val); >>> + if (ret) >>> + return ret; >>> + >>> + calib = tegra124_pad_calibration[val & FUSE_SATA_CALIB_MASK]; >>> + >>> + writel(BIT(0), tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX); >>> + >>> + val = readl(tegra->sata_regs + >>> + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN1); >>> + val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_MASK; >>> + val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_MASK; >>> + val |= calib.gen1_tx_amp << >>> T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT; >>> + val |= calib.gen1_tx_peak << >>> T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT; >>> + writel(val, tegra->sata_regs + SCFG_OFFSET + >>> + T_SATA0_CHX_PHY_CTRL1_GEN1); >>> + >>> + val = readl(tegra->sata_regs + >>> + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN2); >>> + val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_AMP_MASK; >>> + val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_PEAK_MASK; >>> + val |= calib.gen2_tx_amp << >>> T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT; >>> + val |= calib.gen2_tx_peak << >>> T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT; >>> + writel(val, tegra->sata_regs + SCFG_OFFSET + >>> + T_SATA0_CHX_PHY_CTRL1_GEN2); >>> + >>> + writel(T_SATA0_CHX_PHY_CTRL11_GEN2_RX_EQ, >>> + tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL11); >>> + writel(T_SATA0_CHX_PHY_CTRL2_CDR_CNTL_GEN1, >>> + tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL2); >>> + >>> + writel(0, tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX); >>> + >>> + return 0; >>> +} >>> + >>> +static const struct tegra_ahci_soc tegra124_ahci_soc_data = { >>> + .supply_names = tegra124_supply_names, >>> + .num_supplies = ARRAY_SIZE(tegra124_supply_names), >>> + .quirks = NO_DIPM | NO_DEVSLP, >>> + .ops = { >>> + .init = tegra124_ahci_init, >>> + }, > >Indent this "}," one tab less (i.e. to same level as '.ops') > Okay. >>> +}; >>> + >>> +static const struct tegra_ahci_soc tegra210_ahci_soc_data = { >>> + .quirks = NO_DIPM | NO_DEVSLP, >>> }; >>> >>> static int tegra_ahci_power_on(struct ahci_host_priv *hpriv) @@ >>> -115,7 +254,7 @@ static int tegra_ahci_power_on(struct ahci_host_priv >*hpriv) >>> struct tegra_ahci_priv *tegra = hpriv->plat_data; >>> int ret; >>> >>> - ret = regulator_bulk_enable(ARRAY_SIZE(tegra->supplies), >>> + ret = regulator_bulk_enable(tegra->soc_data->num_supplies, >>> tegra->supplies); >>> if (ret) >>> return ret; >>> @@ -144,8 +283,7 @@ static int tegra_ahci_power_on(struct >>> ahci_host_priv >>> *hpriv) >>> tegra_powergate_power_off(TEGRA_POWERGATE_SATA); >>> >>> disable_regulators: >>> - regulator_bulk_disable(ARRAY_SIZE(tegra->supplies), tegra->supplies); >>> - >>> + regulator_bulk_disable(tegra->soc_data->num_supplies, >>> +tegra->supplies); > >Indent this. > This seems to be issue with my outlook. I don't see this issue when I sent first using git send-email. Will take care of this. >>> return ret; >>> } >>> >>> @@ -162,97 +300,137 @@ static void tegra_ahci_power_off(struct >>> ahci_host_priv *hpriv) >>> clk_disable_unprepare(tegra->sata_clk); >>> tegra_powergate_power_off(TEGRA_POWERGATE_SATA); >>> >>> - regulator_bulk_disable(ARRAY_SIZE(tegra->supplies), tegra->supplies); >>> + regulator_bulk_disable(tegra->soc_data->num_supplies, >>> +tegra->supplies); > >And this > This again seems to be issue with my outlook. Will correct it. >>> } >>> >>> static int tegra_ahci_controller_init(struct ahci_host_priv *hpriv) { >>> struct tegra_ahci_priv *tegra = hpriv->plat_data; >>> int ret; >>> - unsigned int val; >>> - struct sata_pad_calibration calib; >>> + u32 val; >>> >>> ret = tegra_ahci_power_on(hpriv); >>> - if (ret) { >>> - dev_err(&tegra->pdev->dev, >>> - "failed to power on AHCI controller: %d\n", ret); >>> + if (ret) >>> return ret; >>> - } >>> >>> + /* >>> + * Program the following SATA IPFS registers > >Extra space between "following" and "SATA" > Okay, will correct it. >>> + * to allow SW accesses to SATA's MMIO Register > >Perhaps say "register range" > >>> + */ >>> + val = readl(tegra->sata_regs + SATA_FPCI_BAR5); >>> + val &= ~(SATA_FPCI_BAR5_START_MASK | >>> SATA_FPCI_BAR5_ACCESS_TYPE); >>> + val |= SATA_FPCI_BAR5_START | SATA_FPCI_BAR5_ACCESS_TYPE; >>> + writel(val, tegra->sata_regs + SATA_FPCI_BAR5); >>> + >>> + /* Program the following SATA IPFS register to enable the SATA */ >>> val = readl(tegra->sata_regs + SATA_CONFIGURATION_0); >>> - val |= SATA_CONFIGURATION_EN_FPCI; >>> + val |= SATA_CONFIGURATION_0_EN_FPCI; >>> writel(val, tegra->sata_regs + SATA_CONFIGURATION_0); >>> >>> - /* Pad calibration */ >>> - >>> - ret = tegra_fuse_readl(FUSE_SATA_CALIB, &val); >>> - if (ret) { >>> - dev_err(&tegra->pdev->dev, >>> - "failed to read calibration fuse: %d\n", ret); >>> - return ret; >>> - } >>> - >>> - calib = tegra124_pad_calibration[val & FUSE_SATA_CALIB_MASK]; >>> - >>> - writel(BIT(0), tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX); >>> - >>> - val = readl(tegra->sata_regs + >>> - SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN1); >>> - val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_MASK; >>> - val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_MASK; >>> - val |= calib.gen1_tx_amp << >>> - T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT; >>> - val |= calib.gen1_tx_peak << >>> - T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT; >>> - writel(val, tegra->sata_regs + SCFG_OFFSET + >>> - T_SATA0_CHX_PHY_CTRL1_GEN1); >>> - >>> - val = readl(tegra->sata_regs + >>> - SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN2); >>> - val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_AMP_MASK; >>> - val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_PEAK_MASK; >>> - val |= calib.gen2_tx_amp << >>> - T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT; >>> - val |= calib.gen2_tx_peak << >>> - T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT; >>> - writel(val, tegra->sata_regs + SCFG_OFFSET + >>> - T_SATA0_CHX_PHY_CTRL1_GEN2); >>> - >>> - writel(T_SATA0_CHX_PHY_CTRL11_GEN2_RX_EQ, >>> - tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL11); >>> - writel(T_SATA0_CHX_PHY_CTRL2_CDR_CNTL_GEN1, >>> - tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL2); >>> - >>> - writel(0, tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX); >>> - >>> - /* Program controller device ID */ >>> + /* Electrical settings for better link stability */ >>> + val = T_SATA0_CHX_PHY_CTRL17_0_RX_EQ_CTRL_L_GEN1; >>> + writel(val, tegra->sata_regs + SCFG_OFFSET + >>> T_SATA0_CHX_PHY_CTRL17_0); >>> + val = T_SATA0_CHX_PHY_CTRL18_0_RX_EQ_CTRL_L_GEN2; >>> + writel(val, tegra->sata_regs + SCFG_OFFSET + >>> T_SATA0_CHX_PHY_CTRL18_0); >>> + val = T_SATA0_CHX_PHY_CTRL20_0_RX_EQ_CTRL_H_GEN1; >>> + writel(val, tegra->sata_regs + SCFG_OFFSET + >>> T_SATA0_CHX_PHY_CTRL20_0); >>> + val = T_SATA0_CHX_PHY_CTRL21_0_RX_EQ_CTRL_H_GEN2; >>> + writel(val, tegra->sata_regs + SCFG_OFFSET + >>> +T_SATA0_CHX_PHY_CTRL21_0); > >Indent > >>> + >>> + /* For SQUELCH Filter & Gen3 drive getting detected as Gen1 drive >>> +*/ >>> + >>> + val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA_CFG_PHY_0); >>> + val |= T_SATA_CFG_PHY_0_MASK_SQUELCH; >>> + val &= ~T_SATA_CFG_PHY_0_USE_7BIT_ALIGN_DET_FOR_SPD; >>> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA_CFG_PHY_0); >>> + >>> + val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_NVOOB); >>> + val &= ~(T_SATA0_NVOOB_COMMA_CNT_MASK | >>> + T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH_MASK | >>> + T_SATA0_NVOOB_SQUELCH_FILTER_MODE_MASK); >>> + val |= (T_SATA0_NVOOB_COMMA_CNT | >>> + T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH | >>> + T_SATA0_NVOOB_SQUELCH_FILTER_MODE); >>> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_NVOOB); >>> + >>> + /* >>> + * Change CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW from 83.3 ns to >>> 58.8ns >>> + */ >>> + val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG2NVOOB_2); >>> + val &= ~T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW_MASK; >>> + val |= T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW; >>> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG2NVOOB_2); >>> + >>> + if (tegra->soc_data->ops.init) >>> + tegra->soc_data->ops.init(hpriv); >>> + >>> + /* >>> + * Program the following SATA configuration registers >>> + * to initialize SATA >>> + */ >>> + val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1); >>> + val |= (T_SATA0_CFG_1_IO_SPACE | T_SATA0_CFG_1_MEMORY_SPACE | >>> + T_SATA0_CFG_1_BUS_MASTER | T_SATA0_CFG_1_SERR); >>> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1); >>> + val = T_SATA0_CFG_9_BASE_ADDRESS; >>> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_9); >>> >>> + /* Program Class Code and Programming interface for SATA */ >>> val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA); >>> val |= T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN; >>> writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA); >>> >>> - writel(0x01060100, tegra->sata_regs + SCFG_OFFSET + >>> T_SATA0_BKDOOR_CC); >>> + val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_BKDOOR_CC); >>> + val &= >>> + ~(T_SATA0_BKDOOR_CC_CLASS_CODE_MASK | >>> + T_SATA0_BKDOOR_CC_PROG_IF_MASK); >>> + val |= T_SATA0_BKDOOR_CC_CLASS_CODE | >>> T_SATA0_BKDOOR_CC_PROG_IF; >>> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_BKDOOR_CC); >>> >>> val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA); >>> val &= ~T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN; >>> writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA); >>> >>> - /* Enable IO & memory access, bus master mode */ >>> - >>> - val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1); >>> - val |= T_SATA0_CFG_1_IO_SPACE | T_SATA0_CFG_1_MEMORY_SPACE | >>> - T_SATA0_CFG_1_BUS_MASTER | T_SATA0_CFG_1_SERR; >>> - writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1); >>> - >>> - /* Program SATA MMIO */ >>> - >>> - writel(0x10000 << SATA_FPCI_BAR5_START_SHIFT, >>> - tegra->sata_regs + SATA_FPCI_BAR5); >>> - >>> - writel(0x08000 << T_SATA0_CFG_9_BASE_ADDRESS_SHIFT, >>> - tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_9); >>> + /* Enabling LPM capabilities through Backdoor Programming */ >>> + val = readl(tegra->sata_regs + SCFG_OFFSET + >>> T_SATA0_AHCI_HBA_CAP_BKDR); >>> + val |= (T_SATA0_AHCI_HBA_CAP_BKDR_PARTIAL_ST_CAP | >>> + T_SATA0_AHCI_HBA_CAP_BKDR_SLUMBER_ST_CAP | >>> + T_SATA0_AHCI_HBA_CAP_BKDR_SALP | >>> + T_SATA0_AHCI_HBA_CAP_BKDR_SUPP_PM); >>> + writel(val, tegra->sata_regs + SCFG_OFFSET + >>> +T_SATA0_AHCI_HBA_CAP_BKDR); >>> + >>> + /* SATA Second Level Clock Gating configuration >>> + * Enabling Gating of Tx/Rx clocks and driving Pad IDDQ and Lane >>> + * IDDQ Signals >>> + */ >>> + val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_35); >>> + val &= ~T_SATA0_CFG_35_IDP_INDEX_MASK; >>> + val |= T_SATA0_CFG_35_IDP_INDEX; >>> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_35); >>> + >>> + val = T_SATA0_AHCI_IDP1_DATA; >>> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_AHCI_IDP1); >>> + >>> + val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_PHY_1); >>> + val |= (T_SATA0_CFG_PHY_1_PADS_IDDQ_EN | >>> + T_SATA0_CFG_PHY_1_PAD_PLL_IDDQ_EN); >>> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_PHY_1); >>> + >>> + /* >>> + * Indicate Sata only has the capability to enter DevSleep > >Stray space in front > Okay, will correct it. >>> + * from slumber link. >>> + */ >>> + >>> + val = readl(tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0); >>> + val |= SATA_AUX_MISC_CNTL_1_0_DESO_SUPPORT; >>> + writel(val, tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0); >>> + >>> + /* Enabling IPFS Clock Gating */ >>> + val = readl(tegra->sata_regs + SATA_CONFIGURATION_0); >>> + val &= ~SATA_CONFIGURATION_0_CLK_OVERRIDE; >>> + writel(val, tegra->sata_regs + SATA_CONFIGURATION_0); >>> >>> - /* Unmask SATA interrupts */ >>> + tegra_ahci_handle_quirks(hpriv); >>> >>> val = readl(tegra->sata_regs + SATA_INTR_MASK); >>> val |= SATA_INTR_MASK_IP_INT_MASK; >>> @@ -278,7 +456,7 @@ static struct ata_port_operations >>> ahci_tegra_port_ops = { >>> .host_stop = tegra_ahci_host_stop, >>> }; >>> >>> -static const struct ata_port_info ahci_tegra_port_info = { >>> +static struct ata_port_info ahci_tegra_port_info = { >>> .flags = AHCI_FLAG_COMMON, >>> .pio_mask = ATA_PIO4, >>> .udma_mask = ATA_UDMA6, >>> @@ -286,7 +464,14 @@ static const struct ata_port_info >>> ahci_tegra_port_info = { }; >>> >>> static const struct of_device_id tegra_ahci_of_match[] = { >>> - { .compatible = "nvidia,tegra124-ahci" }, >>> + { >>> + .compatible = "nvidia,tegra124-ahci", >>> + .data = &tegra124_ahci_soc_data >>> + }, >>> + { >>> + .compatible = "nvidia,tegra210-ahci", >>> + .data = &tegra210_ahci_soc_data >>> + }, >>> {} >>> }; >>> MODULE_DEVICE_TABLE(of, tegra_ahci_of_match); @@ -295,12 +480,27 >@@ >>> static struct scsi_host_template ahci_platform_sht = { >>> AHCI_SHT(DRV_NAME), >>> }; >>> >>> +static void tegra_ahci_handle_quirks(struct ahci_host_priv *hpriv) { >>> + struct tegra_ahci_priv *tegra = hpriv->plat_data; >>> + u32 val; >>> + >>> + if (tegra->soc_data->quirks & NO_DEVSLP) { >>> + val = readl(tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0); >>> + val &= ~SATA_AUX_MISC_CNTL_1_0_SDS_SUPPORT; >>> + writel(val, tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0); >>> + } else if (tegra->soc_data->quirks & NO_DIPM) { > >I don't think this should be 'else if', but just two separate regular 'if's? > Okay, will correct it. >>> + ahci_tegra_port_info.flags |= ATA_FLAG_NO_DIPM; > >Looking at the downstream device trees, it looks like DIPM and DEVSLP are still >disabled for Tegra186 - so why don't we just hardcode these quirks, by always >writing the MISC_CNTL_1_0 register and just adding ATA_FLAG_NO_DIPM to >ahci_tegra_port_info's static definition. > For Tegra186 the devslp pin is shared with PCIE clk req pin. In downstream PCIe driver by default assumes that CLKREQ is present and it owns it. So by default devslp is disabled. We verify devslp by making sure that pcie does not own this pin. This issue will be fixed in future chips. >>> + } >>> +} >>> + >>> static int tegra_ahci_probe(struct platform_device *pdev) { >>> struct ahci_host_priv *hpriv; >>> struct tegra_ahci_priv *tegra; >>> struct resource *res; >>> int ret; >>> + unsigned int i; >>> >>> hpriv = ahci_platform_get_resources(pdev); >>> if (IS_ERR(hpriv)) >>> @@ -311,13 +511,18 @@ static int tegra_ahci_probe(struct >>> platform_device >>> *pdev) >>> return -ENOMEM; >>> >>> hpriv->plat_data = tegra; >>> - >>> tegra->pdev = pdev; >>> + tegra->soc_data = >>> + (struct tegra_ahci_soc *)of_device_get_match_data(&pdev->dev); >>> >>> res = platform_get_resource(pdev, IORESOURCE_MEM, 1); >>> tegra->sata_regs = devm_ioremap_resource(&pdev->dev, res); >>> if (IS_ERR(tegra->sata_regs)) >>> return PTR_ERR(tegra->sata_regs); >>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 2); >>> + tegra->sata_aux_regs = devm_ioremap_resource(&pdev->dev, res); >>> + if (IS_ERR(tegra->sata_aux_regs)) >>> + return PTR_ERR(tegra->sata_aux_regs); > >Requiring aux_regs would break backwards compatibility for Tegra124 device >trees. We will have to keep aux_regs optional for Tegra124, and skip writes to >them if they are not available. > As explained in the other patch, In current driver changes we are touching the devslp register to disable DevSlp which is a part of AUX for both t124 and t210. By default the devslp is enabled for T124 and T210. (Reset value is 1). I will add this aux register in T124 node as well. >>> >>> tegra->sata_rst = devm_reset_control_get(&pdev->dev, "sata"); >>> if (IS_ERR(tegra->sata_rst)) { >>> @@ -343,13 +548,17 @@ static int tegra_ahci_probe(struct >>> platform_device >>> *pdev) >>> return PTR_ERR(tegra->sata_clk); >>> } >>> >>> - tegra->supplies[0].supply = "avdd"; >>> - tegra->supplies[1].supply = "hvdd"; >>> - tegra->supplies[2].supply = "vddio"; >>> - tegra->supplies[3].supply = "target-5v"; >>> - tegra->supplies[4].supply = "target-12v"; >>> + tegra->supplies = devm_kcalloc(&pdev->dev, >>> + tegra->soc_data->num_supplies, >>> + sizeof(*tegra->supplies), GFP_KERNEL); >>> + if (!tegra->supplies) >>> + return -ENOMEM; >>> + >>> + for (i = 0; i < tegra->soc_data->num_supplies; i++) >>> + tegra->supplies[i].supply = tegra->soc_data->supply_names[i]; >>> >>> - ret = devm_regulator_bulk_get(&pdev->dev, ARRAY_SIZE(tegra- >>>> supplies), >>> + ret = devm_regulator_bulk_get(&pdev->dev, >>> + tegra->soc_data->num_supplies, >>> tegra->supplies); >>> if (ret) { >>> dev_err(&pdev->dev, "Failed to get regulators\n"); @@ -385,5 >>> +594,5 @@ static struct platform_driver tegra_ahci_driver = { >>> module_platform_driver(tegra_ahci_driver); >>> >>> MODULE_AUTHOR("Mikko Perttunen <mperttunen-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>"); >>> -MODULE_DESCRIPTION("Tegra124 AHCI SATA driver"); >>> +MODULE_DESCRIPTION("Tegra AHCI SATA driver"); >>> MODULE_LICENSE("GPL v2"); >>> -- >>> 2.1.4 >> >> -- >> To unsubscribe from this list: send the line "unsubscribe linux-tegra" >> in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo >> info at http://vger.kernel.org/majordomo-info.html >> > >Thanks for posting! > >Mikko ^ permalink raw reply [flat|nested] 14+ messages in thread
[parent not found: <db35147839414c609a5dc2cde44dd998-gjLx+0+SZqK6sJks/06JalaTQe2KTcn/@public.gmane.org>]
* Re: [PATCH V3 1/3] ata: ahci_tegra: Add AHCI support for tegra210 [not found] ` <db35147839414c609a5dc2cde44dd998-gjLx+0+SZqK6sJks/06JalaTQe2KTcn/@public.gmane.org> @ 2017-05-24 7:14 ` Mikko Perttunen [not found] ` <6a39df12-c51d-d5b5-c126-1f264bb00ad0-/1wQRMveznE@public.gmane.org> 0 siblings, 1 reply; 14+ messages in thread From: Mikko Perttunen @ 2017-05-24 7:14 UTC (permalink / raw) To: Preetham Chandru, thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org Cc: linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Laxman Dewangan, preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, Venu Byravarasu, Pavan Kunapuli, linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org On 24.05.2017 08:44, Preetham Chandru wrote: > > >> -----Original Message----- >> From: Mikko Perttunen [mailto:cyndis-/1wQRMveznE@public.gmane.org] >> Sent: Sunday, May 14, 2017 4:49 PM >> To: Preetham Chandru <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; >> tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org >> Cc: tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; Laxman Dewangan >> <ldewangan-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; Venu Byravarasu >> <vbyravarasu-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; Pavan Kunapuli <pkunapuli-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; linux- >> tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org >> Subject: Re: [PATCH V3 1/3] ata: ahci_tegra: Add AHCI support for tegra210 >> >> On 05/12/2017 12:55 PM, Preetham Chandru wrote: >>> +CC linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org >>> >>>> -----Original Message----- >>>> From: Preetham Chandru >>>> Sent: Friday, May 12, 2017 3:04 PM >>>> To: thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org >>>> Cc: tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; Laxman Dewangan >>>> <ldewangan-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; Venu Byravarasu >>>> <vbyravarasu-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; Pavan Kunapuli <pkunapuli-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; >>>> Preetham Chandru <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >>>> Subject: [PATCH V3 1/3] ata: ahci_tegra: Add AHCI support for >>>> tegra210 >>>> >>>> From: Preetham Chandru R <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >>>> >>>> 1. Move tegra124 specifics to tegra124_ahci_init. >>>> 2. Separate the regulators needed for tegra124 and tegra210. >>>> 3. Disable DIPM and Devslp for t210 and t124 as there are known >>>> issues >>>> >>>> Signed-off-by: Preetham Chandru R <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >>>> --- >>>> v3: >>>> * Remove inline functions for read/write and modify to SATA, SATA >>>> Config and SATA Aux registers. >>>> * Add code to disable DIPM and DevSlp for t210 and t124 >>>> v2: >>>> * Fix indentation issues >>>> * Move the change to disable DIPM, HIPM, DevSlp, partial, slumber >>>> and NCQ into a separate patch >>>> --- >>>> drivers/ata/ahci_tegra.c | 377 >>>> ++++++++++++++++++++++++++++++++++++------- >>>> ---- >>>> 1 file changed, 293 insertions(+), 84 deletions(-) >>>> >>>> diff --git a/drivers/ata/ahci_tegra.c b/drivers/ata/ahci_tegra.c >>>> index >>>> 3a62eb2..cd581a6 100644 >>>> --- a/drivers/ata/ahci_tegra.c >>>> +++ b/drivers/ata/ahci_tegra.c >>>> @@ -34,7 +34,8 @@ >>>> #define DRV_NAME "tegra-ahci" >>>> >>>> #define SATA_CONFIGURATION_0 0x180 >>>> -#define SATA_CONFIGURATION_EN_FPCI BIT(0) >>>> +#define SATA_CONFIGURATION_0_EN_FPCI BIT(0) >>>> +#define SATA_CONFIGURATION_0_CLK_OVERRIDE BIT(31) >>>> >>>> #define SCFG_OFFSET 0x1000 >>>> >>>> @@ -45,17 +46,55 @@ >>>> #define T_SATA0_CFG_1_SERR BIT(8) >>>> >>>> #define T_SATA0_CFG_9 0x24 >>>> -#define T_SATA0_CFG_9_BASE_ADDRESS_SHIFT 13 >>>> +#define T_SATA0_CFG_9_BASE_ADDRESS 0x40020000 >>>> >>>> #define SATA_FPCI_BAR5 0x94 >>>> -#define SATA_FPCI_BAR5_START_SHIFT 4 >>>> +#define SATA_FPCI_BAR5_START_MASK (0xfffffff << 4) >>>> +#define SATA_FPCI_BAR5_START (0x0040020 << >>>> 4) >>>> +#define SATA_FPCI_BAR5_ACCESS_TYPE (0x1) >>>> >>>> #define SATA_INTR_MASK 0x188 >>>> #define SATA_INTR_MASK_IP_INT_MASK BIT(16) >>>> >>>> +#define T_SATA0_CFG_35 0x94 >>>> +#define T_SATA0_CFG_35_IDP_INDEX_MASK (0x7ff >> << 2) >>>> +#define T_SATA0_CFG_35_IDP_INDEX (0x2a << 2) >>>> + >>>> +#define T_SATA0_AHCI_IDP1 0x98 >>>> +#define T_SATA0_AHCI_IDP1_DATA (0x400040) >>>> + >>>> +#define T_SATA0_CFG_PHY_1 0x12c >>>> +#define T_SATA0_CFG_PHY_1_PADS_IDDQ_EN BIT(23) >>>> +#define T_SATA0_CFG_PHY_1_PAD_PLL_IDDQ_EN BIT(22) >>>> + >>>> +#define T_SATA0_NVOOB 0x114 >>>> +#define T_SATA0_NVOOB_COMMA_CNT_MASK (0xff << 16) >>>> +#define T_SATA0_NVOOB_COMMA_CNT (0x07 << 16) >>>> +#define T_SATA0_NVOOB_SQUELCH_FILTER_MODE_MASK (0x3 << 24) >>>> +#define T_SATA0_NVOOB_SQUELCH_FILTER_MODE (0x1 << 24) >>>> +#define T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH_MASK (0x3 << 26) >>>> +#define T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH (0x3 << 26) >>>> + >>>> +#define T_SATA_CFG_PHY_0 0x120 >>>> +#define T_SATA_CFG_PHY_0_USE_7BIT_ALIGN_DET_FOR_SPD BIT(11) >>>> +#define T_SATA_CFG_PHY_0_MASK_SQUELCH BIT(24) >>>> + >>>> +#define T_SATA0_CFG2NVOOB_2 0x134 >>>> +#define T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW_MASK >> (0x1ff >>>> << 18) >>>> +#define T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW (0xc << >> 18) >>>> + >>>> #define T_SATA0_AHCI_HBA_CAP_BKDR 0x300 >>>> +#define T_SATA0_AHCI_HBA_CAP_BKDR_PARTIAL_ST_CAP BIT(13) >>>> +#define T_SATA0_AHCI_HBA_CAP_BKDR_SLUMBER_ST_CAP BIT(14) >>>> +#define T_SATA0_AHCI_HBA_CAP_BKDR_SALP BIT(26) >>>> +#define T_SATA0_AHCI_HBA_CAP_BKDR_SUPP_PM BIT(17) >>>> +#define T_SATA0_AHCI_HBA_CAP_BKDR_SNCQ BIT(30) >>>> >>>> #define T_SATA0_BKDOOR_CC 0x4a4 >>>> +#define T_SATA0_BKDOOR_CC_CLASS_CODE_MASK (0xffff << 16) >>>> +#define T_SATA0_BKDOOR_CC_CLASS_CODE >> (0x0106 << 16) >>>> +#define T_SATA0_BKDOOR_CC_PROG_IF_MASK (0xff << >> 8) >>>> +#define T_SATA0_BKDOOR_CC_PROG_IF (0x01 << 8) >>>> >>>> #define T_SATA0_CFG_SATA 0x54c >>>> #define T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN BIT(12) >>>> @@ -82,9 +121,35 @@ >>>> #define T_SATA0_CHX_PHY_CTRL11 0x6d0 >>>> #define T_SATA0_CHX_PHY_CTRL11_GEN2_RX_EQ (0x2800 << 16) >>>> >>>> +#define T_SATA0_CHX_PHY_CTRL17_0 0x6e8 >>>> +#define T_SATA0_CHX_PHY_CTRL17_0_RX_EQ_CTRL_L_GEN1 >> 0x55010000 >>>> +#define T_SATA0_CHX_PHY_CTRL18_0 0x6ec >>>> +#define T_SATA0_CHX_PHY_CTRL18_0_RX_EQ_CTRL_L_GEN2 >> 0x55010000 >>>> +#define T_SATA0_CHX_PHY_CTRL20_0 0x6f4 >>>> +#define T_SATA0_CHX_PHY_CTRL20_0_RX_EQ_CTRL_H_GEN1 0x1 >>>> +#define T_SATA0_CHX_PHY_CTRL21_0 0x6f8 >>>> +#define T_SATA0_CHX_PHY_CTRL21_0_RX_EQ_CTRL_H_GEN2 0x1 >>>> + >>>> +/* AUX Registers */ >>>> +#define SATA_AUX_MISC_CNTL_1_0 0x8 >>>> +#define SATA_AUX_MISC_CNTL_1_0_DEVSLP_OVERRIDE BIT(17) >>>> +#define SATA_AUX_MISC_CNTL_1_0_SDS_SUPPORT BIT(13) >>>> +#define SATA_AUX_MISC_CNTL_1_0_DESO_SUPPORT BIT(15) >>>> + >>>> +#define SATA_AUX_RX_STAT_INT_0 0xc >>>> +#define SATA_AUX_RX_STAT_INT_0_SATA_DEVSLP BIT(7) >>>> + >>>> +#define SATA_AUX_SPARE_CFG0_0 0x18 >>>> +#define SATA_AUX_SPARE_CFG0_0_MDAT_TIMER_AFTER_PG_VALID BIT(14) >>>> + >>>> #define FUSE_SATA_CALIB 0x124 >>>> #define FUSE_SATA_CALIB_MASK 0x3 >>>> >>>> +enum { >>>> + NO_DEVSLP = (1 << 0), >>>> + NO_DIPM = (1 << 1), >>>> +}; >>>> + >>>> struct sata_pad_calibration { >>>> u8 gen1_tx_amp; >>>> u8 gen1_tx_peak; >>>> @@ -99,15 +164,89 @@ static const struct sata_pad_calibration >>>> tegra124_pad_calibration[] = { >>>> {0x14, 0x0e, 0x1a, 0x0e}, >>>> }; >>>> >>>> +struct tegra_ahci_ops { >>>> + int (*init)(struct ahci_host_priv *); }; >>>> + >>>> +struct tegra_ahci_soc { >>>> + const char *const *supply_names; >>>> + u32 num_supplies; >>>> + u32 quirks; >>>> + struct tegra_ahci_ops ops; >>>> +}; >>>> + >>>> struct tegra_ahci_priv { >>>> struct platform_device *pdev; >>>> void __iomem *sata_regs; >>>> + void __iomem *sata_aux_regs; >>>> struct reset_control *sata_rst; >>>> struct reset_control *sata_oob_rst; >>>> struct reset_control *sata_cold_rst; >>>> /* Needs special handling, cannot use ahci_platform */ >>>> struct clk *sata_clk; >>>> - struct regulator_bulk_data supplies[5]; >>>> + struct regulator_bulk_data *supplies; >>>> + struct tegra_ahci_soc *soc_data; >>>> +}; >>>> + >>>> +static const char *const tegra124_supply_names[] = { >>>> + "avdd", "hvdd", "vddio", "target-5v", "target-12v" >>>> +}; >>>> + >>>> +static int tegra124_ahci_init(struct ahci_host_priv *hpriv) { >>>> + struct tegra_ahci_priv *tegra = hpriv->plat_data; >>>> + struct sata_pad_calibration calib; >>>> + int ret; >>>> + u32 val; >>>> + >>>> + /* Pad calibration */ >>>> + ret = tegra_fuse_readl(FUSE_SATA_CALIB, &val); >>>> + if (ret) >>>> + return ret; >>>> + >>>> + calib = tegra124_pad_calibration[val & FUSE_SATA_CALIB_MASK]; >>>> + >>>> + writel(BIT(0), tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX); >>>> + >>>> + val = readl(tegra->sata_regs + >>>> + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN1); >>>> + val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_MASK; >>>> + val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_MASK; >>>> + val |= calib.gen1_tx_amp << >>>> T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT; >>>> + val |= calib.gen1_tx_peak << >>>> T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT; >>>> + writel(val, tegra->sata_regs + SCFG_OFFSET + >>>> + T_SATA0_CHX_PHY_CTRL1_GEN1); >>>> + >>>> + val = readl(tegra->sata_regs + >>>> + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN2); >>>> + val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_AMP_MASK; >>>> + val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_PEAK_MASK; >>>> + val |= calib.gen2_tx_amp << >>>> T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT; >>>> + val |= calib.gen2_tx_peak << >>>> T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT; >>>> + writel(val, tegra->sata_regs + SCFG_OFFSET + >>>> + T_SATA0_CHX_PHY_CTRL1_GEN2); >>>> + >>>> + writel(T_SATA0_CHX_PHY_CTRL11_GEN2_RX_EQ, >>>> + tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL11); >>>> + writel(T_SATA0_CHX_PHY_CTRL2_CDR_CNTL_GEN1, >>>> + tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL2); >>>> + >>>> + writel(0, tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX); >>>> + >>>> + return 0; >>>> +} >>>> + >>>> +static const struct tegra_ahci_soc tegra124_ahci_soc_data = { >>>> + .supply_names = tegra124_supply_names, >>>> + .num_supplies = ARRAY_SIZE(tegra124_supply_names), >>>> + .quirks = NO_DIPM | NO_DEVSLP, >>>> + .ops = { >>>> + .init = tegra124_ahci_init, >>>> + }, >> >> Indent this "}," one tab less (i.e. to same level as '.ops') >> > Okay. > >>>> +}; >>>> + >>>> +static const struct tegra_ahci_soc tegra210_ahci_soc_data = { >>>> + .quirks = NO_DIPM | NO_DEVSLP, >>>> }; >>>> >>>> static int tegra_ahci_power_on(struct ahci_host_priv *hpriv) @@ >>>> -115,7 +254,7 @@ static int tegra_ahci_power_on(struct ahci_host_priv >> *hpriv) >>>> struct tegra_ahci_priv *tegra = hpriv->plat_data; >>>> int ret; >>>> >>>> - ret = regulator_bulk_enable(ARRAY_SIZE(tegra->supplies), >>>> + ret = regulator_bulk_enable(tegra->soc_data->num_supplies, >>>> tegra->supplies); >>>> if (ret) >>>> return ret; >>>> @@ -144,8 +283,7 @@ static int tegra_ahci_power_on(struct >>>> ahci_host_priv >>>> *hpriv) >>>> tegra_powergate_power_off(TEGRA_POWERGATE_SATA); >>>> >>>> disable_regulators: >>>> - regulator_bulk_disable(ARRAY_SIZE(tegra->supplies), tegra->supplies); >>>> - >>>> + regulator_bulk_disable(tegra->soc_data->num_supplies, >>>> +tegra->supplies); >> >> Indent this. >> > This seems to be issue with my outlook. I don't see this issue > when I sent first using git send-email. Will take care of this. > >>>> return ret; >>>> } >>>> >>>> @@ -162,97 +300,137 @@ static void tegra_ahci_power_off(struct >>>> ahci_host_priv *hpriv) >>>> clk_disable_unprepare(tegra->sata_clk); >>>> tegra_powergate_power_off(TEGRA_POWERGATE_SATA); >>>> >>>> - regulator_bulk_disable(ARRAY_SIZE(tegra->supplies), tegra->supplies); >>>> + regulator_bulk_disable(tegra->soc_data->num_supplies, >>>> +tegra->supplies); >> >> And this >> > This again seems to be issue with my outlook. Will correct it. >>>> } >>>> >>>> static int tegra_ahci_controller_init(struct ahci_host_priv *hpriv) { >>>> struct tegra_ahci_priv *tegra = hpriv->plat_data; >>>> int ret; >>>> - unsigned int val; >>>> - struct sata_pad_calibration calib; >>>> + u32 val; >>>> >>>> ret = tegra_ahci_power_on(hpriv); >>>> - if (ret) { >>>> - dev_err(&tegra->pdev->dev, >>>> - "failed to power on AHCI controller: %d\n", ret); >>>> + if (ret) >>>> return ret; >>>> - } >>>> >>>> + /* >>>> + * Program the following SATA IPFS registers >> >> Extra space between "following" and "SATA" >> > Okay, will correct it. >>>> + * to allow SW accesses to SATA's MMIO Register >> >> Perhaps say "register range" >> >>>> + */ >>>> + val = readl(tegra->sata_regs + SATA_FPCI_BAR5); >>>> + val &= ~(SATA_FPCI_BAR5_START_MASK | >>>> SATA_FPCI_BAR5_ACCESS_TYPE); >>>> + val |= SATA_FPCI_BAR5_START | SATA_FPCI_BAR5_ACCESS_TYPE; >>>> + writel(val, tegra->sata_regs + SATA_FPCI_BAR5); >>>> + >>>> + /* Program the following SATA IPFS register to enable the SATA */ >>>> val = readl(tegra->sata_regs + SATA_CONFIGURATION_0); >>>> - val |= SATA_CONFIGURATION_EN_FPCI; >>>> + val |= SATA_CONFIGURATION_0_EN_FPCI; >>>> writel(val, tegra->sata_regs + SATA_CONFIGURATION_0); >>>> >>>> - /* Pad calibration */ >>>> - >>>> - ret = tegra_fuse_readl(FUSE_SATA_CALIB, &val); >>>> - if (ret) { >>>> - dev_err(&tegra->pdev->dev, >>>> - "failed to read calibration fuse: %d\n", ret); >>>> - return ret; >>>> - } >>>> - >>>> - calib = tegra124_pad_calibration[val & FUSE_SATA_CALIB_MASK]; >>>> - >>>> - writel(BIT(0), tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX); >>>> - >>>> - val = readl(tegra->sata_regs + >>>> - SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN1); >>>> - val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_MASK; >>>> - val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_MASK; >>>> - val |= calib.gen1_tx_amp << >>>> - T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT; >>>> - val |= calib.gen1_tx_peak << >>>> - T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT; >>>> - writel(val, tegra->sata_regs + SCFG_OFFSET + >>>> - T_SATA0_CHX_PHY_CTRL1_GEN1); >>>> - >>>> - val = readl(tegra->sata_regs + >>>> - SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN2); >>>> - val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_AMP_MASK; >>>> - val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_PEAK_MASK; >>>> - val |= calib.gen2_tx_amp << >>>> - T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT; >>>> - val |= calib.gen2_tx_peak << >>>> - T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT; >>>> - writel(val, tegra->sata_regs + SCFG_OFFSET + >>>> - T_SATA0_CHX_PHY_CTRL1_GEN2); >>>> - >>>> - writel(T_SATA0_CHX_PHY_CTRL11_GEN2_RX_EQ, >>>> - tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL11); >>>> - writel(T_SATA0_CHX_PHY_CTRL2_CDR_CNTL_GEN1, >>>> - tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL2); >>>> - >>>> - writel(0, tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX); >>>> - >>>> - /* Program controller device ID */ >>>> + /* Electrical settings for better link stability */ >>>> + val = T_SATA0_CHX_PHY_CTRL17_0_RX_EQ_CTRL_L_GEN1; >>>> + writel(val, tegra->sata_regs + SCFG_OFFSET + >>>> T_SATA0_CHX_PHY_CTRL17_0); >>>> + val = T_SATA0_CHX_PHY_CTRL18_0_RX_EQ_CTRL_L_GEN2; >>>> + writel(val, tegra->sata_regs + SCFG_OFFSET + >>>> T_SATA0_CHX_PHY_CTRL18_0); >>>> + val = T_SATA0_CHX_PHY_CTRL20_0_RX_EQ_CTRL_H_GEN1; >>>> + writel(val, tegra->sata_regs + SCFG_OFFSET + >>>> T_SATA0_CHX_PHY_CTRL20_0); >>>> + val = T_SATA0_CHX_PHY_CTRL21_0_RX_EQ_CTRL_H_GEN2; >>>> + writel(val, tegra->sata_regs + SCFG_OFFSET + >>>> +T_SATA0_CHX_PHY_CTRL21_0); >> >> Indent >> >>>> + >>>> + /* For SQUELCH Filter & Gen3 drive getting detected as Gen1 drive >>>> +*/ >>>> + >>>> + val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA_CFG_PHY_0); >>>> + val |= T_SATA_CFG_PHY_0_MASK_SQUELCH; >>>> + val &= ~T_SATA_CFG_PHY_0_USE_7BIT_ALIGN_DET_FOR_SPD; >>>> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA_CFG_PHY_0); >>>> + >>>> + val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_NVOOB); >>>> + val &= ~(T_SATA0_NVOOB_COMMA_CNT_MASK | >>>> + T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH_MASK | >>>> + T_SATA0_NVOOB_SQUELCH_FILTER_MODE_MASK); >>>> + val |= (T_SATA0_NVOOB_COMMA_CNT | >>>> + T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH | >>>> + T_SATA0_NVOOB_SQUELCH_FILTER_MODE); >>>> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_NVOOB); >>>> + >>>> + /* >>>> + * Change CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW from 83.3 ns to >>>> 58.8ns >>>> + */ >>>> + val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG2NVOOB_2); >>>> + val &= ~T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW_MASK; >>>> + val |= T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW; >>>> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG2NVOOB_2); >>>> + >>>> + if (tegra->soc_data->ops.init) >>>> + tegra->soc_data->ops.init(hpriv); >>>> + >>>> + /* >>>> + * Program the following SATA configuration registers >>>> + * to initialize SATA >>>> + */ >>>> + val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1); >>>> + val |= (T_SATA0_CFG_1_IO_SPACE | T_SATA0_CFG_1_MEMORY_SPACE | >>>> + T_SATA0_CFG_1_BUS_MASTER | T_SATA0_CFG_1_SERR); >>>> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1); >>>> + val = T_SATA0_CFG_9_BASE_ADDRESS; >>>> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_9); >>>> >>>> + /* Program Class Code and Programming interface for SATA */ >>>> val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA); >>>> val |= T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN; >>>> writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA); >>>> >>>> - writel(0x01060100, tegra->sata_regs + SCFG_OFFSET + >>>> T_SATA0_BKDOOR_CC); >>>> + val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_BKDOOR_CC); >>>> + val &= >>>> + ~(T_SATA0_BKDOOR_CC_CLASS_CODE_MASK | >>>> + T_SATA0_BKDOOR_CC_PROG_IF_MASK); >>>> + val |= T_SATA0_BKDOOR_CC_CLASS_CODE | >>>> T_SATA0_BKDOOR_CC_PROG_IF; >>>> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_BKDOOR_CC); >>>> >>>> val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA); >>>> val &= ~T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN; >>>> writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA); >>>> >>>> - /* Enable IO & memory access, bus master mode */ >>>> - >>>> - val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1); >>>> - val |= T_SATA0_CFG_1_IO_SPACE | T_SATA0_CFG_1_MEMORY_SPACE | >>>> - T_SATA0_CFG_1_BUS_MASTER | T_SATA0_CFG_1_SERR; >>>> - writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1); >>>> - >>>> - /* Program SATA MMIO */ >>>> - >>>> - writel(0x10000 << SATA_FPCI_BAR5_START_SHIFT, >>>> - tegra->sata_regs + SATA_FPCI_BAR5); >>>> - >>>> - writel(0x08000 << T_SATA0_CFG_9_BASE_ADDRESS_SHIFT, >>>> - tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_9); >>>> + /* Enabling LPM capabilities through Backdoor Programming */ >>>> + val = readl(tegra->sata_regs + SCFG_OFFSET + >>>> T_SATA0_AHCI_HBA_CAP_BKDR); >>>> + val |= (T_SATA0_AHCI_HBA_CAP_BKDR_PARTIAL_ST_CAP | >>>> + T_SATA0_AHCI_HBA_CAP_BKDR_SLUMBER_ST_CAP | >>>> + T_SATA0_AHCI_HBA_CAP_BKDR_SALP | >>>> + T_SATA0_AHCI_HBA_CAP_BKDR_SUPP_PM); >>>> + writel(val, tegra->sata_regs + SCFG_OFFSET + >>>> +T_SATA0_AHCI_HBA_CAP_BKDR); >>>> + >>>> + /* SATA Second Level Clock Gating configuration >>>> + * Enabling Gating of Tx/Rx clocks and driving Pad IDDQ and Lane >>>> + * IDDQ Signals >>>> + */ >>>> + val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_35); >>>> + val &= ~T_SATA0_CFG_35_IDP_INDEX_MASK; >>>> + val |= T_SATA0_CFG_35_IDP_INDEX; >>>> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_35); >>>> + >>>> + val = T_SATA0_AHCI_IDP1_DATA; >>>> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_AHCI_IDP1); >>>> + >>>> + val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_PHY_1); >>>> + val |= (T_SATA0_CFG_PHY_1_PADS_IDDQ_EN | >>>> + T_SATA0_CFG_PHY_1_PAD_PLL_IDDQ_EN); >>>> + writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_PHY_1); >>>> + >>>> + /* >>>> + * Indicate Sata only has the capability to enter DevSleep >> >> Stray space in front >> > Okay, will correct it. >>>> + * from slumber link. >>>> + */ >>>> + >>>> + val = readl(tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0); >>>> + val |= SATA_AUX_MISC_CNTL_1_0_DESO_SUPPORT; >>>> + writel(val, tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0); >>>> + >>>> + /* Enabling IPFS Clock Gating */ >>>> + val = readl(tegra->sata_regs + SATA_CONFIGURATION_0); >>>> + val &= ~SATA_CONFIGURATION_0_CLK_OVERRIDE; >>>> + writel(val, tegra->sata_regs + SATA_CONFIGURATION_0); >>>> >>>> - /* Unmask SATA interrupts */ >>>> + tegra_ahci_handle_quirks(hpriv); >>>> >>>> val = readl(tegra->sata_regs + SATA_INTR_MASK); >>>> val |= SATA_INTR_MASK_IP_INT_MASK; >>>> @@ -278,7 +456,7 @@ static struct ata_port_operations >>>> ahci_tegra_port_ops = { >>>> .host_stop = tegra_ahci_host_stop, >>>> }; >>>> >>>> -static const struct ata_port_info ahci_tegra_port_info = { >>>> +static struct ata_port_info ahci_tegra_port_info = { >>>> .flags = AHCI_FLAG_COMMON, >>>> .pio_mask = ATA_PIO4, >>>> .udma_mask = ATA_UDMA6, >>>> @@ -286,7 +464,14 @@ static const struct ata_port_info >>>> ahci_tegra_port_info = { }; >>>> >>>> static const struct of_device_id tegra_ahci_of_match[] = { >>>> - { .compatible = "nvidia,tegra124-ahci" }, >>>> + { >>>> + .compatible = "nvidia,tegra124-ahci", >>>> + .data = &tegra124_ahci_soc_data >>>> + }, >>>> + { >>>> + .compatible = "nvidia,tegra210-ahci", >>>> + .data = &tegra210_ahci_soc_data >>>> + }, >>>> {} >>>> }; >>>> MODULE_DEVICE_TABLE(of, tegra_ahci_of_match); @@ -295,12 +480,27 >> @@ >>>> static struct scsi_host_template ahci_platform_sht = { >>>> AHCI_SHT(DRV_NAME), >>>> }; >>>> >>>> +static void tegra_ahci_handle_quirks(struct ahci_host_priv *hpriv) { >>>> + struct tegra_ahci_priv *tegra = hpriv->plat_data; >>>> + u32 val; >>>> + >>>> + if (tegra->soc_data->quirks & NO_DEVSLP) { >>>> + val = readl(tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0); >>>> + val &= ~SATA_AUX_MISC_CNTL_1_0_SDS_SUPPORT; >>>> + writel(val, tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0); >>>> + } else if (tegra->soc_data->quirks & NO_DIPM) { >> >> I don't think this should be 'else if', but just two separate regular 'if's? >> > Okay, will correct it. >>>> + ahci_tegra_port_info.flags |= ATA_FLAG_NO_DIPM; >> >> Looking at the downstream device trees, it looks like DIPM and DEVSLP are still >> disabled for Tegra186 - so why don't we just hardcode these quirks, by always >> writing the MISC_CNTL_1_0 register and just adding ATA_FLAG_NO_DIPM to >> ahci_tegra_port_info's static definition. >> > > For Tegra186 the devslp pin is shared with PCIE clk req pin. > In downstream PCIe driver by default assumes that CLKREQ is present and it owns it. > So by default devslp is disabled. We verify devslp by making sure that pcie does not > own this pin. This issue will be fixed in future chips. Ok. How about DIPM, can we hardcode that? If not, or if it is fixed in Xavier, I think it would be cleaner to have two static port_info structs and select between then based on the quirk, so that we don't need to mutate the static data. > >>>> + } >>>> +} >>>> + >>>> static int tegra_ahci_probe(struct platform_device *pdev) { >>>> struct ahci_host_priv *hpriv; >>>> struct tegra_ahci_priv *tegra; >>>> struct resource *res; >>>> int ret; >>>> + unsigned int i; >>>> >>>> hpriv = ahci_platform_get_resources(pdev); >>>> if (IS_ERR(hpriv)) >>>> @@ -311,13 +511,18 @@ static int tegra_ahci_probe(struct >>>> platform_device >>>> *pdev) >>>> return -ENOMEM; >>>> >>>> hpriv->plat_data = tegra; >>>> - >>>> tegra->pdev = pdev; >>>> + tegra->soc_data = >>>> + (struct tegra_ahci_soc *)of_device_get_match_data(&pdev->dev); >>>> >>>> res = platform_get_resource(pdev, IORESOURCE_MEM, 1); >>>> tegra->sata_regs = devm_ioremap_resource(&pdev->dev, res); >>>> if (IS_ERR(tegra->sata_regs)) >>>> return PTR_ERR(tegra->sata_regs); >>>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 2); >>>> + tegra->sata_aux_regs = devm_ioremap_resource(&pdev->dev, res); >>>> + if (IS_ERR(tegra->sata_aux_regs)) >>>> + return PTR_ERR(tegra->sata_aux_regs); >> >> Requiring aux_regs would break backwards compatibility for Tegra124 device >> trees. We will have to keep aux_regs optional for Tegra124, and skip writes to >> them if they are not available. >> > > As explained in the other patch, In current driver changes we are touching the > devslp register to disable DevSlp which is a part of AUX for both t124 and t210. > By default the devslp is enabled for T124 and T210. (Reset value is 1). > I will add this aux register in T124 node as well. According to device tree stability, the kernel must work with older device trees that had support for the device. So for T124, we need to continue to support older device trees without the aux_regs property. > >>>> >>>> tegra->sata_rst = devm_reset_control_get(&pdev->dev, "sata"); >>>> if (IS_ERR(tegra->sata_rst)) { >>>> @@ -343,13 +548,17 @@ static int tegra_ahci_probe(struct >>>> platform_device >>>> *pdev) >>>> return PTR_ERR(tegra->sata_clk); >>>> } >>>> >>>> - tegra->supplies[0].supply = "avdd"; >>>> - tegra->supplies[1].supply = "hvdd"; >>>> - tegra->supplies[2].supply = "vddio"; >>>> - tegra->supplies[3].supply = "target-5v"; >>>> - tegra->supplies[4].supply = "target-12v"; >>>> + tegra->supplies = devm_kcalloc(&pdev->dev, >>>> + tegra->soc_data->num_supplies, >>>> + sizeof(*tegra->supplies), GFP_KERNEL); >>>> + if (!tegra->supplies) >>>> + return -ENOMEM; >>>> + >>>> + for (i = 0; i < tegra->soc_data->num_supplies; i++) >>>> + tegra->supplies[i].supply = tegra->soc_data->supply_names[i]; >>>> >>>> - ret = devm_regulator_bulk_get(&pdev->dev, ARRAY_SIZE(tegra- >>>>> supplies), >>>> + ret = devm_regulator_bulk_get(&pdev->dev, >>>> + tegra->soc_data->num_supplies, >>>> tegra->supplies); >>>> if (ret) { >>>> dev_err(&pdev->dev, "Failed to get regulators\n"); @@ -385,5 >>>> +594,5 @@ static struct platform_driver tegra_ahci_driver = { >>>> module_platform_driver(tegra_ahci_driver); >>>> >>>> MODULE_AUTHOR("Mikko Perttunen <mperttunen-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>"); >>>> -MODULE_DESCRIPTION("Tegra124 AHCI SATA driver"); >>>> +MODULE_DESCRIPTION("Tegra AHCI SATA driver"); >>>> MODULE_LICENSE("GPL v2"); >>>> -- >>>> 2.1.4 >>> >>> -- >>> To unsubscribe from this list: send the line "unsubscribe linux-tegra" >>> in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo >>> info at http://vger.kernel.org/majordomo-info.html >>> >> >> Thanks for posting! >> >> Mikko > -- > To unsubscribe from this list: send the line "unsubscribe linux-tegra" in > the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > ^ permalink raw reply [flat|nested] 14+ messages in thread
[parent not found: <6a39df12-c51d-d5b5-c126-1f264bb00ad0-/1wQRMveznE@public.gmane.org>]
* Re: [PATCH V3 1/3] ata: ahci_tegra: Add AHCI support for tegra210 [not found] ` <6a39df12-c51d-d5b5-c126-1f264bb00ad0-/1wQRMveznE@public.gmane.org> @ 2017-05-24 7:15 ` Mikko Perttunen [not found] ` <e7a2cbef-71c7-cffb-58d5-aac998c8e156-/1wQRMveznE@public.gmane.org> 2017-05-25 11:11 ` Preetham Chandru 1 sibling, 1 reply; 14+ messages in thread From: Mikko Perttunen @ 2017-05-24 7:15 UTC (permalink / raw) To: Preetham Chandru, thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org Cc: linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Laxman Dewangan, preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, Venu Byravarasu, Pavan Kunapuli, linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org Also Vagrant Cascadian mentioned on IRC that the call to tegra_ahci_handle_quirks is currently before the definition of the function which causes warnings or compilation errors. So please add a declaration of the function before the call. Cheers, Mikko. On 24.05.2017 10:14, Mikko Perttunen wrote: > On 24.05.2017 08:44, Preetham Chandru wrote: >> ... ^ permalink raw reply [flat|nested] 14+ messages in thread
[parent not found: <e7a2cbef-71c7-cffb-58d5-aac998c8e156-/1wQRMveznE@public.gmane.org>]
* RE: [PATCH V3 1/3] ata: ahci_tegra: Add AHCI support for tegra210 [not found] ` <e7a2cbef-71c7-cffb-58d5-aac998c8e156-/1wQRMveznE@public.gmane.org> @ 2017-05-25 11:15 ` Preetham Chandru 0 siblings, 0 replies; 14+ messages in thread From: Preetham Chandru @ 2017-05-25 11:15 UTC (permalink / raw) To: Mikko Perttunen, thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org Cc: linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Laxman Dewangan, preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, Venu Byravarasu, Pavan Kunapuli, linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org >-----Original Message----- >From: Mikko Perttunen [mailto:cyndis-/1wQRMveznE@public.gmane.org] >Sent: Wednesday, May 24, 2017 12:46 PM >To: Preetham Chandru <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; >tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org >Cc: linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; Laxman Dewangan <ldewangan-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; >preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; Venu Byravarasu <vbyravarasu-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; Pavan >Kunapuli <pkunapuli-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org >Subject: Re: [PATCH V3 1/3] ata: ahci_tegra: Add AHCI support for tegra210 > >Also Vagrant Cascadian mentioned on IRC that the call to >tegra_ahci_handle_quirks is currently before the definition of the function which >causes warnings or compilation errors. So please add a declaration of the >function before the call. > Okay. >Cheers, >Mikko. > >On 24.05.2017 10:14, Mikko Perttunen wrote: >> On 24.05.2017 08:44, Preetham Chandru wrote: >>> ... ^ permalink raw reply [flat|nested] 14+ messages in thread
* RE: [PATCH V3 1/3] ata: ahci_tegra: Add AHCI support for tegra210 [not found] ` <6a39df12-c51d-d5b5-c126-1f264bb00ad0-/1wQRMveznE@public.gmane.org> 2017-05-24 7:15 ` Mikko Perttunen @ 2017-05-25 11:11 ` Preetham Chandru 1 sibling, 0 replies; 14+ messages in thread From: Preetham Chandru @ 2017-05-25 11:11 UTC (permalink / raw) To: Mikko Perttunen, thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org Cc: linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Laxman Dewangan, preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, Venu Byravarasu, Pavan Kunapuli, linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org >>>>> + ahci_tegra_port_info.flags |= ATA_FLAG_NO_DIPM; >>> >>> Looking at the downstream device trees, it looks like DIPM and DEVSLP >>> are still disabled for Tegra186 - so why don't we just hardcode these >>> quirks, by always writing the MISC_CNTL_1_0 register and just adding >>> ATA_FLAG_NO_DIPM to ahci_tegra_port_info's static definition. >>> >> >> For Tegra186 the devslp pin is shared with PCIE clk req pin. >> In downstream PCIe driver by default assumes that CLKREQ is present and it >owns it. >> So by default devslp is disabled. We verify devslp by making sure that >> pcie does not own this pin. This issue will be fixed in future chips. > >Ok. How about DIPM, can we hardcode that? If not, or if it is fixed in Xavier, I >think it would be cleaner to have two static port_info structs and select between >then based on the quirk, so that we don't need to mutate the static data. > No, DIPM is not fixed in that chip as well. I will hardcode it now and in future when it gets fixed we can have two port_info structs as suggested. ^ permalink raw reply [flat|nested] 14+ messages in thread
[parent not found: <1494581650-11115-3-git-send-email-pchandru@nvidia.com>]
[parent not found: <1494581650-11115-3-git-send-email-pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>]
* RE: [PATCH V3 2/3] dt-bindings: tegra: Add tegra210 AHCI [not found] ` <1494581650-11115-3-git-send-email-pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> @ 2017-05-12 9:55 ` Preetham Chandru [not found] ` <66578c4b5f77447aa6c4e3c7ce0cf8db-7W72rfoJkVnYuxH7O460wFaTQe2KTcn/@public.gmane.org> 0 siblings, 1 reply; 14+ messages in thread From: Preetham Chandru @ 2017-05-12 9:55 UTC (permalink / raw) To: thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org Cc: tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Laxman Dewangan, preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, Venu Byravarasu, Pavan Kunapuli, linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org +CC linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org >-----Original Message----- >From: Preetham Chandru >Sent: Friday, May 12, 2017 3:04 PM >To: thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org >Cc: tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; Laxman Dewangan ><ldewangan-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; Venu Byravarasu ><vbyravarasu-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; Pavan Kunapuli <pkunapuli-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; Preetham >Chandru <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >Subject: [PATCH V3 2/3] dt-bindings: tegra: Add tegra210 AHCI > >From: Preetham Chandru R <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> > >Signed-off-by: Preetham Chandru R <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >--- >v3: >* Add AUX register. >v2: >* change cml1, pll_e and phy regulators as optional > for T210. >--- > .../bindings/ata/nvidia,tegra124-ahci.txt | 45 +++++++++++++++------- > 1 file changed, 31 insertions(+), 14 deletions(-) > >diff --git a/Documentation/devicetree/bindings/ata/nvidia,tegra124-ahci.txt >b/Documentation/devicetree/bindings/ata/nvidia,tegra124-ahci.txt >index 66c83c3..dc62dba 100644 >--- a/Documentation/devicetree/bindings/ata/nvidia,tegra124-ahci.txt >+++ b/Documentation/devicetree/bindings/ata/nvidia,tegra124-ahci.txt >@@ -1,32 +1,49 @@ >-Tegra124 SoC SATA AHCI controller >+Tegra SoC SATA AHCI controller > > Required properties : >-- compatible : For Tegra124, must contain "nvidia,tegra124-ahci". Otherwise, >- must contain '"nvidia,<chip>-ahci", "nvidia,tegra124-ahci"', where <chip> >- is tegra132. >-- reg : Should contain 2 entries: >+- compatible : Must be one of: >+ - Tegra124 : "nvidia,tegra124-ahci" >+ - Tegra210 : "nvidia,tegra210-ahci" >+- reg : Should contain 3 entries: > - AHCI register set (SATA BAR5) > - SATA register set >+ - AUX register set > - interrupts : Defines the interrupt used by SATA > - clocks : Must contain an entry for each entry in clock-names. > See ../clocks/clock-bindings.txt for details. > - clock-names : Must include the following entries: > - sata > - sata-oob >- - cml1 >- - pll_e > - resets : Must contain an entry for each entry in reset-names. > See ../reset/reset.txt for details. > - reset-names : Must include the following entries: > - sata > - sata-oob >- - sata-cold >+ - For T124: sata-cold > - phys : Must contain an entry for each entry in phy-names. > See ../phy/phy-bindings.txt for details. > - phy-names : Must include the following entries: >- - sata-phy : XUSB PADCTL SATA PHY >-- hvdd-supply : Defines the SATA HVDD regulator >-- vddio-supply : Defines the SATA VDDIO regulator >-- avdd-supply : Defines the SATA AVDD regulator >-- target-5v-supply : Defines the SATA 5V power regulator >-- target-12v-supply : Defines the SATA 12V power regulator >+ - For T124: >+ - sata-phy : XUSB PADCTL SATA PHY >+ - For T210: >+ - sata-0 >+- For T124: >+ - hvdd-supply : Defines the SATA HVDD regulator >+ - vddio-supply : Defines the SATA VDDIO regulator >+ - avdd-supply : Defines the SATA AVDD regulator >+ - target-5v-supply : Defines the SATA 5V power regulator >+ >+Optional properties: >+- clock-names : >+ - cml1 : >+ cml1 clock is required by phy so it is optional to define >+ here as phy driver will be enabling this clock. >+ - pll_e : >+ pll_e is the parent of cml1 clock so it is optional to define >+ here as phy driver will be enabling this clock. >+- For T210: >+ - l0-hvddio-sata-supply : Defines the SATA HVDDIO regulator >+ - l0-dvddio-sata-supply : Defines the SATA DVDDIO regulator >+ - hvdd-pex-pll-e-supply : Defines the PEX PLL_E regulator >+ - dvdd-sata-pll-supply : Defines the SATA PLL regulator >+ - hvdd-sata-supply : Defines the SATA HVDD regulator >-- >2.1.4 ^ permalink raw reply [flat|nested] 14+ messages in thread
[parent not found: <66578c4b5f77447aa6c4e3c7ce0cf8db-7W72rfoJkVnYuxH7O460wFaTQe2KTcn/@public.gmane.org>]
* Re: [PATCH V3 2/3] dt-bindings: tegra: Add tegra210 AHCI [not found] ` <66578c4b5f77447aa6c4e3c7ce0cf8db-7W72rfoJkVnYuxH7O460wFaTQe2KTcn/@public.gmane.org> @ 2017-05-14 11:26 ` Mikko Perttunen [not found] ` <8b842356-90ef-8214-7104-ea1f417717cb-/1wQRMveznE@public.gmane.org> 0 siblings, 1 reply; 14+ messages in thread From: Mikko Perttunen @ 2017-05-14 11:26 UTC (permalink / raw) To: Preetham Chandru, thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org Cc: tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Laxman Dewangan, preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, Venu Byravarasu, Pavan Kunapuli, linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org On 05/12/2017 12:55 PM, Preetham Chandru wrote: > +CC linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org > >> -----Original Message----- >> From: Preetham Chandru >> Sent: Friday, May 12, 2017 3:04 PM >> To: thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org >> Cc: tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; Laxman Dewangan >> <ldewangan-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; Venu Byravarasu >> <vbyravarasu-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; Pavan Kunapuli <pkunapuli-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; Preetham >> Chandru <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >> Subject: [PATCH V3 2/3] dt-bindings: tegra: Add tegra210 AHCI >> >> From: Preetham Chandru R <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >> This needs a commit message. Something simple, like "This adds bindings documentation for the AHCI controller on Tegra210." is fine. >> Signed-off-by: Preetham Chandru R <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >> --- >> v3: >> * Add AUX register. >> v2: >> * change cml1, pll_e and phy regulators as optional >> for T210. >> --- >> .../bindings/ata/nvidia,tegra124-ahci.txt | 45 +++++++++++++++------- >> 1 file changed, 31 insertions(+), 14 deletions(-) >> >> diff --git a/Documentation/devicetree/bindings/ata/nvidia,tegra124-ahci.txt >> b/Documentation/devicetree/bindings/ata/nvidia,tegra124-ahci.txt >> index 66c83c3..dc62dba 100644 >> --- a/Documentation/devicetree/bindings/ata/nvidia,tegra124-ahci.txt >> +++ b/Documentation/devicetree/bindings/ata/nvidia,tegra124-ahci.txt >> @@ -1,32 +1,49 @@ >> -Tegra124 SoC SATA AHCI controller >> +Tegra SoC SATA AHCI controller >> >> Required properties : >> -- compatible : For Tegra124, must contain "nvidia,tegra124-ahci". Otherwise, >> - must contain '"nvidia,<chip>-ahci", "nvidia,tegra124-ahci"', where <chip> >> - is tegra132. >> -- reg : Should contain 2 entries: >> +- compatible : Must be one of: >> + - Tegra124 : "nvidia,tegra124-ahci" >> + - Tegra210 : "nvidia,tegra210-ahci" >> +- reg : Should contain 3 entries: >> - AHCI register set (SATA BAR5) >> - SATA register set >> + - AUX register set The AUX register set must be optional on Tegra124, as it was not required previously. >> - interrupts : Defines the interrupt used by SATA >> - clocks : Must contain an entry for each entry in clock-names. >> See ../clocks/clock-bindings.txt for details. >> - clock-names : Must include the following entries: >> - sata >> - sata-oob >> - - cml1 >> - - pll_e >> - resets : Must contain an entry for each entry in reset-names. >> See ../reset/reset.txt for details. >> - reset-names : Must include the following entries: >> - sata >> - sata-oob >> - - sata-cold >> + - For T124: sata-cold >> - phys : Must contain an entry for each entry in phy-names. >> See ../phy/phy-bindings.txt for details. >> - phy-names : Must include the following entries: >> - - sata-phy : XUSB PADCTL SATA PHY >> -- hvdd-supply : Defines the SATA HVDD regulator >> -- vddio-supply : Defines the SATA VDDIO regulator >> -- avdd-supply : Defines the SATA AVDD regulator >> -- target-5v-supply : Defines the SATA 5V power regulator >> -- target-12v-supply : Defines the SATA 12V power regulator >> + - For T124: >> + - sata-phy : XUSB PADCTL SATA PHY >> + - For T210: >> + - sata-0 >> +- For T124: >> + - hvdd-supply : Defines the SATA HVDD regulator >> + - vddio-supply : Defines the SATA VDDIO regulator >> + - avdd-supply : Defines the SATA AVDD regulator >> + - target-5v-supply : Defines the SATA 5V power regulator This is missing the 12V supply regulator >> + >> +Optional properties: >> +- clock-names : >> + - cml1 : >> + cml1 clock is required by phy so it is optional to define >> + here as phy driver will be enabling this clock. >> + - pll_e : >> + pll_e is the parent of cml1 clock so it is optional to define >> + here as phy driver will be enabling this clock. >> +- For T210: >> + - l0-hvddio-sata-supply : Defines the SATA HVDDIO regulator >> + - l0-dvddio-sata-supply : Defines the SATA DVDDIO regulator >> + - hvdd-pex-pll-e-supply : Defines the PEX PLL_E regulator >> + - dvdd-sata-pll-supply : Defines the SATA PLL regulator >> + - hvdd-sata-supply : Defines the SATA HVDD regulator I don't think the driver currently has code to enable these regulators? >> -- >> 2.1.4 > > -- > To unsubscribe from this list: send the line "unsubscribe linux-tegra" in > the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > ^ permalink raw reply [flat|nested] 14+ messages in thread
[parent not found: <8b842356-90ef-8214-7104-ea1f417717cb-/1wQRMveznE@public.gmane.org>]
* RE: [PATCH V3 2/3] dt-bindings: tegra: Add tegra210 AHCI [not found] ` <8b842356-90ef-8214-7104-ea1f417717cb-/1wQRMveznE@public.gmane.org> @ 2017-05-24 4:56 ` Preetham Chandru 0 siblings, 0 replies; 14+ messages in thread From: Preetham Chandru @ 2017-05-24 4:56 UTC (permalink / raw) To: Mikko Perttunen, thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org Cc: tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Laxman Dewangan, preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, Venu Byravarasu, Pavan Kunapuli, linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org >-----Original Message----- >From: Mikko Perttunen [mailto:cyndis-/1wQRMveznE@public.gmane.org] >Sent: Sunday, May 14, 2017 4:56 PM >To: Preetham Chandru <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; >tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org >Cc: tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; Laxman Dewangan ><ldewangan-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; Venu Byravarasu ><vbyravarasu-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; Pavan Kunapuli <pkunapuli-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; linux- >tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org >Subject: Re: [PATCH V3 2/3] dt-bindings: tegra: Add tegra210 AHCI > >On 05/12/2017 12:55 PM, Preetham Chandru wrote: >> +CC linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org >> >>> -----Original Message----- >>> From: Preetham Chandru >>> Sent: Friday, May 12, 2017 3:04 PM >>> To: thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org >>> Cc: tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; Laxman Dewangan >>> <ldewangan-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; Venu Byravarasu >>> <vbyravarasu-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; Pavan Kunapuli <pkunapuli-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; >>> Preetham Chandru <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >>> Subject: [PATCH V3 2/3] dt-bindings: tegra: Add tegra210 AHCI >>> >>> From: Preetham Chandru R <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >>> > >This needs a commit message. Something simple, like "This adds bindings >documentation for the AHCI controller on Tegra210." is fine. > Okay, will change it. >>> Signed-off-by: Preetham Chandru R <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >>> --- >>> v3: >>> * Add AUX register. >>> v2: >>> * change cml1, pll_e and phy regulators as optional for T210. >>> --- >>> .../bindings/ata/nvidia,tegra124-ahci.txt | 45 +++++++++++++++------- >>> 1 file changed, 31 insertions(+), 14 deletions(-) >>> >>> diff --git >>> a/Documentation/devicetree/bindings/ata/nvidia,tegra124-ahci.txt >>> b/Documentation/devicetree/bindings/ata/nvidia,tegra124-ahci.txt >>> index 66c83c3..dc62dba 100644 >>> --- a/Documentation/devicetree/bindings/ata/nvidia,tegra124-ahci.txt >>> +++ b/Documentation/devicetree/bindings/ata/nvidia,tegra124-ahci.txt >>> @@ -1,32 +1,49 @@ >>> -Tegra124 SoC SATA AHCI controller >>> +Tegra SoC SATA AHCI controller >>> >>> Required properties : >>> -- compatible : For Tegra124, must contain "nvidia,tegra124-ahci". >>> Otherwise, >>> - must contain '"nvidia,<chip>-ahci", "nvidia,tegra124-ahci"', where >>> <chip> >>> - is tegra132. >>> -- reg : Should contain 2 entries: >>> +- compatible : Must be one of: >>> + - Tegra124 : "nvidia,tegra124-ahci" >>> + - Tegra210 : "nvidia,tegra210-ahci" >>> +- reg : Should contain 3 entries: >>> - AHCI register set (SATA BAR5) >>> - SATA register set >>> + - AUX register set > >The AUX register set must be optional on Tegra124, as it was not required >previously. > In current driver changes we are touching the devslp register to disable DevSlp which is a part of AUX for both t124 and t210. By default the devslp is enabled for T124 and T210. (Reset value is 1). I will add this aux register in T124 node as well. >>> - interrupts : Defines the interrupt used by SATA >>> - clocks : Must contain an entry for each entry in clock-names. >>> See ../clocks/clock-bindings.txt for details. >>> - clock-names : Must include the following entries: >>> - sata >>> - sata-oob >>> - - cml1 >>> - - pll_e >>> - resets : Must contain an entry for each entry in reset-names. >>> See ../reset/reset.txt for details. >>> - reset-names : Must include the following entries: >>> - sata >>> - sata-oob >>> - - sata-cold >>> + - For T124: sata-cold >>> - phys : Must contain an entry for each entry in phy-names. >>> See ../phy/phy-bindings.txt for details. >>> - phy-names : Must include the following entries: >>> - - sata-phy : XUSB PADCTL SATA PHY >>> -- hvdd-supply : Defines the SATA HVDD regulator >>> -- vddio-supply : Defines the SATA VDDIO regulator >>> -- avdd-supply : Defines the SATA AVDD regulator >>> -- target-5v-supply : Defines the SATA 5V power regulator >>> -- target-12v-supply : Defines the SATA 12V power regulator >>> + - For T124: >>> + - sata-phy : XUSB PADCTL SATA PHY >>> + - For T210: >>> + - sata-0 >>> +- For T124: >>> + - hvdd-supply : Defines the SATA HVDD regulator >>> + - vddio-supply : Defines the SATA VDDIO regulator >>> + - avdd-supply : Defines the SATA AVDD regulator >>> + - target-5v-supply : Defines the SATA 5V power regulator > >This is missing the 12V supply regulator > Okay. Will add. >>> + >>> +Optional properties: >>> +- clock-names : >>> + - cml1 : >>> + cml1 clock is required by phy so it is optional to define >>> + here as phy driver will be enabling this clock. >>> + - pll_e : >>> + pll_e is the parent of cml1 clock so it is optional to define >>> + here as phy driver will be enabling this clock. >>> +- For T210: >>> + - l0-hvddio-sata-supply : Defines the SATA HVDDIO regulator >>> + - l0-dvddio-sata-supply : Defines the SATA DVDDIO regulator >>> + - hvdd-pex-pll-e-supply : Defines the PEX PLL_E regulator >>> + - dvdd-sata-pll-supply : Defines the SATA PLL regulator >>> + - hvdd-sata-supply : Defines the SATA HVDD regulator > >I don't think the driver currently has code to enable these regulators? > Yes, they will be enabled in uphy. Will remove here. >>> -- >>> 2.1.4 >> >> -- >> To unsubscribe from this list: send the line "unsubscribe linux-tegra" >> in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo >> info at http://vger.kernel.org/majordomo-info.html >> ^ permalink raw reply [flat|nested] 14+ messages in thread
[parent not found: <1494581650-11115-4-git-send-email-pchandru@nvidia.com>]
[parent not found: <1494581650-11115-4-git-send-email-pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>]
* RE: [PATCH V3 3/3] arm64: tegra: Enable SATA on Tegra210 [not found] ` <1494581650-11115-4-git-send-email-pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> @ 2017-05-12 9:56 ` Preetham Chandru [not found] ` <1f54292e718c4bb5a02d547d041804b0-7W72rfoJkVnYuxH7O460wFaTQe2KTcn/@public.gmane.org> 0 siblings, 1 reply; 14+ messages in thread From: Preetham Chandru @ 2017-05-12 9:56 UTC (permalink / raw) To: thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org Cc: tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Laxman Dewangan, preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, Venu Byravarasu, Pavan Kunapuli, linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org +CC linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org >-----Original Message----- >From: Preetham Chandru >Sent: Friday, May 12, 2017 3:04 PM >To: thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org >Cc: tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; Laxman Dewangan ><ldewangan-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; Venu Byravarasu ><vbyravarasu-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; Pavan Kunapuli <pkunapuli-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; Preetham >Chandru <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >Subject: [PATCH V3 3/3] arm64: tegra: Enable SATA on Tegra210 > >From: Preetham Chandru R <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> > >Enable the SATA unit on Tegra210 systems. > >Signed-off-by: Preetham Chandru R <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >--- > arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi | 6 ++++++ > arch/arm64/boot/dts/nvidia/tegra210.dtsi | 16 ++++++++++++++++ > 2 files changed, 22 insertions(+) > >diff --git a/arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi >b/arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi >index e5fc67b..58c28b9 100644 >--- a/arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi >+++ b/arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi >@@ -1324,6 +1324,12 @@ > status = "okay"; > }; > >+ sata@70020000 { >+ status = "okay"; >+ phys = <&{/padctl@7009f000/pads/sata/lanes/sata-0}>; >+ phy-names = "sata-0"; >+ }; >+ > padctl@7009f000 { > status = "okay"; > >diff --git a/arch/arm64/boot/dts/nvidia/tegra210.dtsi >b/arch/arm64/boot/dts/nvidia/tegra210.dtsi >index 8f26c4d..20c9160 100644 >--- a/arch/arm64/boot/dts/nvidia/tegra210.dtsi >+++ b/arch/arm64/boot/dts/nvidia/tegra210.dtsi >@@ -795,6 +795,22 @@ > #iommu-cells = <1>; > }; > >+ sata@70020000 { >+ compatible = "nvidia,tegra210-ahci"; >+ reg = <0x0 0x70027000 0x0 0x2000>, /* AHCI */ >+ <0x0 0x70020000 0x0 0x7000>, /* SATA */ >+ <0x0 0x70001100 0x0 0x1000>; /* SATA AUX*/ >+ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; >+ clocks = <&tegra_car TEGRA210_CLK_SATA>, >+ <&tegra_car TEGRA210_CLK_SATA_OOB>; >+ clock-names = "sata", "sata-oob"; >+ resets = <&tegra_car 124>, >+ <&tegra_car 123>, >+ <&tegra_car 129>; >+ reset-names = "sata", "sata-oob", "sata-cold"; >+ status = "disabled"; >+ }; >+ > hda@70030000 { > compatible = "nvidia,tegra210-hda", "nvidia,tegra30-hda"; > reg = <0x0 0x70030000 0x0 0x10000>; >-- >2.1.4 ^ permalink raw reply [flat|nested] 14+ messages in thread
[parent not found: <1f54292e718c4bb5a02d547d041804b0-7W72rfoJkVnYuxH7O460wFaTQe2KTcn/@public.gmane.org>]
* Re: [PATCH V3 3/3] arm64: tegra: Enable SATA on Tegra210 [not found] ` <1f54292e718c4bb5a02d547d041804b0-7W72rfoJkVnYuxH7O460wFaTQe2KTcn/@public.gmane.org> @ 2017-05-14 11:29 ` Mikko Perttunen [not found] ` <3279be02-37b3-7869-4fe6-5bd20f107f38-/1wQRMveznE@public.gmane.org> 0 siblings, 1 reply; 14+ messages in thread From: Mikko Perttunen @ 2017-05-14 11:29 UTC (permalink / raw) To: Preetham Chandru, thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org Cc: tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Laxman Dewangan, preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, Venu Byravarasu, Pavan Kunapuli, linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org On 05/12/2017 12:56 PM, Preetham Chandru wrote: > +CC linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org > >> -----Original Message----- >> From: Preetham Chandru >> Sent: Friday, May 12, 2017 3:04 PM >> To: thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org >> Cc: tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; Laxman Dewangan >> <ldewangan-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; Venu Byravarasu >> <vbyravarasu-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; Pavan Kunapuli <pkunapuli-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; Preetham >> Chandru <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >> Subject: [PATCH V3 3/3] arm64: tegra: Enable SATA on Tegra210 >> >> From: Preetham Chandru R <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >> >> Enable the SATA unit on Tegra210 systems. >> >> Signed-off-by: Preetham Chandru R <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >> --- >> arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi | 6 ++++++ >> arch/arm64/boot/dts/nvidia/tegra210.dtsi | 16 ++++++++++++++++ >> 2 files changed, 22 insertions(+) >> >> diff --git a/arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi >> b/arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi >> index e5fc67b..58c28b9 100644 >> --- a/arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi >> +++ b/arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi >> @@ -1324,6 +1324,12 @@ >> status = "okay"; >> }; >> >> + sata@70020000 { >> + status = "okay"; >> + phys = <&{/padctl@7009f000/pads/sata/lanes/sata-0}>; >> + phy-names = "sata-0"; >> + }; >> + >> padctl@7009f000 { >> status = "okay"; >> >> diff --git a/arch/arm64/boot/dts/nvidia/tegra210.dtsi >> b/arch/arm64/boot/dts/nvidia/tegra210.dtsi >> index 8f26c4d..20c9160 100644 >> --- a/arch/arm64/boot/dts/nvidia/tegra210.dtsi >> +++ b/arch/arm64/boot/dts/nvidia/tegra210.dtsi >> @@ -795,6 +795,22 @@ >> #iommu-cells = <1>; >> }; >> >> + sata@70020000 { >> + compatible = "nvidia,tegra210-ahci"; >> + reg = <0x0 0x70027000 0x0 0x2000>, /* AHCI */ >> + <0x0 0x70020000 0x0 0x7000>, /* SATA */ >> + <0x0 0x70001100 0x0 0x1000>; /* SATA AUX*/ Missing space after 'AUX' >> + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; >> + clocks = <&tegra_car TEGRA210_CLK_SATA>, >> + <&tegra_car TEGRA210_CLK_SATA_OOB>; >> + clock-names = "sata", "sata-oob"; >> + resets = <&tegra_car 124>, >> + <&tegra_car 123>, >> + <&tegra_car 129>; >> + reset-names = "sata", "sata-oob", "sata-cold"; The binding documentation says that sata-cold is not required for tegra210? >> + status = "disabled"; >> + }; >> + >> hda@70030000 { >> compatible = "nvidia,tegra210-hda", "nvidia,tegra30-hda"; >> reg = <0x0 0x70030000 0x0 0x10000>; >> -- >> 2.1.4 > > -- > To unsubscribe from this list: send the line "unsubscribe linux-tegra" in > the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org > More majordomo info at http://vger.kernel.org/majordomo-info.html > ^ permalink raw reply [flat|nested] 14+ messages in thread
[parent not found: <3279be02-37b3-7869-4fe6-5bd20f107f38-/1wQRMveznE@public.gmane.org>]
* RE: [PATCH V3 3/3] arm64: tegra: Enable SATA on Tegra210 [not found] ` <3279be02-37b3-7869-4fe6-5bd20f107f38-/1wQRMveznE@public.gmane.org> @ 2017-05-24 4:43 ` Preetham Chandru 0 siblings, 0 replies; 14+ messages in thread From: Preetham Chandru @ 2017-05-24 4:43 UTC (permalink / raw) To: Mikko Perttunen, thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org Cc: linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org, Laxman Dewangan, preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org, Venu Byravarasu, Pavan Kunapuli, linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org >-----Original Message----- >From: Mikko Perttunen [mailto:cyndis-/1wQRMveznE@public.gmane.org] >Sent: Sunday, May 14, 2017 4:59 PM >To: Preetham Chandru <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; >tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org >Cc: tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; Laxman Dewangan ><ldewangan-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; Venu Byravarasu ><vbyravarasu-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; Pavan Kunapuli <pkunapuli-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; linux- >tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org >Subject: Re: [PATCH V3 3/3] arm64: tegra: Enable SATA on Tegra210 > >On 05/12/2017 12:56 PM, Preetham Chandru wrote: >> +CC linux-tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org >> >>> -----Original Message----- >>> From: Preetham Chandru >>> Sent: Friday, May 12, 2017 3:04 PM >>> To: thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; tj-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org >>> Cc: tegra-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; linux-ide-u79uwXL29TY76Z2rM5mHXA@public.gmane.org; Laxman Dewangan >>> <ldewangan-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; preetham260-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org; Venu Byravarasu >>> <vbyravarasu-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; Pavan Kunapuli <pkunapuli-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>; >>> Preetham Chandru <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >>> Subject: [PATCH V3 3/3] arm64: tegra: Enable SATA on Tegra210 >>> >>> From: Preetham Chandru R <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >>> >>> Enable the SATA unit on Tegra210 systems. >>> >>> Signed-off-by: Preetham Chandru R <pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org> >>> --- >>> arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi | 6 ++++++ >>> arch/arm64/boot/dts/nvidia/tegra210.dtsi | 16 ++++++++++++++++ >>> 2 files changed, 22 insertions(+) >>> >>> diff --git a/arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi >>> b/arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi >>> index e5fc67b..58c28b9 100644 >>> --- a/arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi >>> +++ b/arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi >>> @@ -1324,6 +1324,12 @@ >>> status = "okay"; >>> }; >>> >>> + sata@70020000 { >>> + status = "okay"; >>> + phys = <&{/padctl@7009f000/pads/sata/lanes/sata-0}>; >>> + phy-names = "sata-0"; >>> + }; >>> + >>> padctl@7009f000 { >>> status = "okay"; >>> >>> diff --git a/arch/arm64/boot/dts/nvidia/tegra210.dtsi >>> b/arch/arm64/boot/dts/nvidia/tegra210.dtsi >>> index 8f26c4d..20c9160 100644 >>> --- a/arch/arm64/boot/dts/nvidia/tegra210.dtsi >>> +++ b/arch/arm64/boot/dts/nvidia/tegra210.dtsi >>> @@ -795,6 +795,22 @@ >>> #iommu-cells = <1>; >>> }; >>> >>> + sata@70020000 { >>> + compatible = "nvidia,tegra210-ahci"; >>> + reg = <0x0 0x70027000 0x0 0x2000>, /* AHCI */ >>> + <0x0 0x70020000 0x0 0x7000>, /* SATA */ >>> + <0x0 0x70001100 0x0 0x1000>; /* SATA AUX*/ > >Missing space after 'AUX' > Okay. >>> + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; >>> + clocks = <&tegra_car TEGRA210_CLK_SATA>, >>> + <&tegra_car TEGRA210_CLK_SATA_OOB>; >>> + clock-names = "sata", "sata-oob"; >>> + resets = <&tegra_car 124>, >>> + <&tegra_car 123>, >>> + <&tegra_car 129>; >>> + reset-names = "sata", "sata-oob", "sata-cold"; > >The binding documentation says that sata-cold is not required for tegra210? > It's a mistake in binding documentation. Will correct it in binding doc. >>> + status = "disabled"; >>> + }; >>> + >>> hda@70030000 { >>> compatible = "nvidia,tegra210-hda", "nvidia,tegra30-hda"; >>> reg = <0x0 0x70030000 0x0 0x10000>; >>> -- >>> 2.1.4 >> >> -- >> To unsubscribe from this list: send the line "unsubscribe linux-tegra" >> in the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org More majordomo >> info at http://vger.kernel.org/majordomo-info.html >> ^ permalink raw reply [flat|nested] 14+ messages in thread
end of thread, other threads:[~2017-05-25 11:15 UTC | newest]
Thread overview: 14+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <1494581650-11115-1-git-send-email-pchandru@nvidia.com>
[not found] ` <1494581650-11115-1-git-send-email-pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
2017-05-12 9:45 ` [PATCH V3 0/3] ADD AHCI support for tegra210 Preetham Chandru
[not found] ` <1494581650-11115-2-git-send-email-pchandru@nvidia.com>
[not found] ` <1494581650-11115-2-git-send-email-pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
2017-05-12 9:55 ` [PATCH V3 1/3] ata: ahci_tegra: Add " Preetham Chandru
[not found] ` <c3457c8e12b0402293bdea825883277f-7W72rfoJkVnYuxH7O460wFaTQe2KTcn/@public.gmane.org>
2017-05-14 11:18 ` Mikko Perttunen
[not found] ` <3dfdc451-794a-832e-4985-ac56d7e1843e-/1wQRMveznE@public.gmane.org>
2017-05-24 5:44 ` Preetham Chandru
[not found] ` <db35147839414c609a5dc2cde44dd998-gjLx+0+SZqK6sJks/06JalaTQe2KTcn/@public.gmane.org>
2017-05-24 7:14 ` Mikko Perttunen
[not found] ` <6a39df12-c51d-d5b5-c126-1f264bb00ad0-/1wQRMveznE@public.gmane.org>
2017-05-24 7:15 ` Mikko Perttunen
[not found] ` <e7a2cbef-71c7-cffb-58d5-aac998c8e156-/1wQRMveznE@public.gmane.org>
2017-05-25 11:15 ` Preetham Chandru
2017-05-25 11:11 ` Preetham Chandru
[not found] ` <1494581650-11115-3-git-send-email-pchandru@nvidia.com>
[not found] ` <1494581650-11115-3-git-send-email-pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
2017-05-12 9:55 ` [PATCH V3 2/3] dt-bindings: tegra: Add tegra210 AHCI Preetham Chandru
[not found] ` <66578c4b5f77447aa6c4e3c7ce0cf8db-7W72rfoJkVnYuxH7O460wFaTQe2KTcn/@public.gmane.org>
2017-05-14 11:26 ` Mikko Perttunen
[not found] ` <8b842356-90ef-8214-7104-ea1f417717cb-/1wQRMveznE@public.gmane.org>
2017-05-24 4:56 ` Preetham Chandru
[not found] ` <1494581650-11115-4-git-send-email-pchandru@nvidia.com>
[not found] ` <1494581650-11115-4-git-send-email-pchandru-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
2017-05-12 9:56 ` [PATCH V3 3/3] arm64: tegra: Enable SATA on Tegra210 Preetham Chandru
[not found] ` <1f54292e718c4bb5a02d547d041804b0-7W72rfoJkVnYuxH7O460wFaTQe2KTcn/@public.gmane.org>
2017-05-14 11:29 ` Mikko Perttunen
[not found] ` <3279be02-37b3-7869-4fe6-5bd20f107f38-/1wQRMveznE@public.gmane.org>
2017-05-24 4:43 ` Preetham Chandru
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox