* [PATCH] ARM: dt: tegra: whistler: add regulators
@ 2012-08-03 18:11 Stephen Warren
[not found] ` <1344017484-29395-1-git-send-email-swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org>
0 siblings, 1 reply; 2+ messages in thread
From: Stephen Warren @ 2012-08-03 18:11 UTC (permalink / raw)
To: Olof Johansson, Colin Cross
Cc: Mark Brown, Laxman Dewangan,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-tegra-u79uwXL29TY76Z2rM5mHXA, Stephen Warren
From: Stephen Warren <swarren-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
Whistler uses a Maxim 8907 regulator. Instantiate this.
The voltage settings were derived from the schematic. The only exception
is the BBAT voltage; the schematic says 1.2v, but the HW can't go that
low, so use the HW default of 2.4v instead.
Almost all regulators list all driven supply signal names in their
regulator-names property. The exception is nvvdd_sv3, which is in turn
named 12 more different names on the schematic, so these were omitted
for brevity.
Signed-off-by: Stephen Warren <swarren-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
---
arch/arm/boot/dts/tegra20-whistler.dts | 294 ++++++++++++++++++++++++++++++++
1 files changed, 294 insertions(+), 0 deletions(-)
diff --git a/arch/arm/boot/dts/tegra20-whistler.dts b/arch/arm/boot/dts/tegra20-whistler.dts
index 6916310..7338baa 100644
--- a/arch/arm/boot/dts/tegra20-whistler.dts
+++ b/arch/arm/boot/dts/tegra20-whistler.dts
@@ -261,6 +261,285 @@
gpio-controller;
#gpio-cells = <2>;
};
+
+ max8907@3c {
+ compatible = "maxim,max8907";
+ reg = <0x3c>;
+ interrupts = <0 86 0x4>;
+
+ mbatt-supply = <&usb0_vbus_reg>;
+ in-v1-supply = <&mbatt_reg>;
+ in-v2-supply = <&mbatt_reg>;
+ in-v3-supply = <&mbatt_reg>;
+ in1-supply = <&mbatt_reg>;
+ in2-supply = <&nvvdd_sv3_reg>;
+ in3-supply = <&mbatt_reg>;
+ in4-supply = <&mbatt_reg>;
+ in5-supply = <&mbatt_reg>;
+ in6-supply = <&mbatt_reg>;
+ in7-supply = <&mbatt_reg>;
+ in8-supply = <&mbatt_reg>;
+ in9-supply = <&mbatt_reg>;
+ in10-supply = <&mbatt_reg>;
+ in11-supply = <&mbatt_reg>;
+ in12-supply = <&mbatt_reg>;
+ in13-supply = <&mbatt_reg>;
+ in14-supply = <&mbatt_reg>;
+ in15-supply = <&mbatt_reg>;
+ in16-supply = <&mbatt_reg>;
+ in17-supply = <&nvvdd_sv3_reg>;
+ in18-supply = <&nvvdd_sv3_reg>;
+ in19-supply = <&mbatt_reg>;
+ in20-supply = <&mbatt_reg>;
+ lxw-supply = <&mbatt_reg>;
+
+ regulators {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mbatt_reg: regulator@0 {
+ reg = <0>;
+ regulator-compatible = "mbatt";
+ regulator-name = "vbat_pmu";
+ regulator-always-on;
+ };
+
+ regulator@1 {
+ reg = <1>;
+ regulator-compatible = "sd1";
+ regulator-name = "nvvdd_sv1,vdd_cpu_pmu";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ regulator@2 {
+ reg = <2>;
+ regulator-compatible = "sd2";
+ regulator-name = "nvvdd_sv2,vdd_core";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ nvvdd_sv3_reg: regulator@3 {
+ reg = <3>;
+ regulator-compatible = "sd3";
+ regulator-name = "nvvdd_sv3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ regulator@4 {
+ reg = <4>;
+ regulator-compatible = "ldo1";
+ regulator-name = "nvvdd_ldo1,vddio_rx_ddr,vcore_acc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ regulator@5 {
+ reg = <5>;
+ regulator-compatible = "ldo2";
+ regulator-name = "nvvdd_ldo2,avdd_pll*";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-always-on;
+ };
+
+ regulator@6 {
+ reg = <6>;
+ regulator-compatible = "ldo3";
+ regulator-name = "nvvdd_ldo3,vcom_1v8b";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ regulator@7 {
+ reg = <7>;
+ regulator-compatible = "ldo4";
+ regulator-name = "nvvdd_ldo4,avdd_usb*";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ regulator@8 {
+ reg = <8>;
+ regulator-compatible = "ldo5";
+ regulator-name = "nvvdd_ldo5,vcore_mmc,avdd_lcd1,vddio_1wire";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ regulator@9 {
+ reg = <9>;
+ regulator-compatible = "ldo6";
+ regulator-name = "nvvdd_ldo6,avdd_hdmi_pll";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ regulator@10 {
+ reg = <10>;
+ regulator-compatible = "ldo7";
+ regulator-name = "nvvdd_ldo7,avddio_audio";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ regulator@11 {
+ reg = <11>;
+ regulator-compatible = "ldo8";
+ regulator-name = "nvvdd_ldo8,vcom_3v0,vcore_cmps";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ regulator@12 {
+ reg = <12>;
+ regulator-compatible = "ldo9";
+ regulator-name = "nvvdd_ldo9,avdd_cam*";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ regulator@13 {
+ reg = <13>;
+ regulator-compatible = "ldo10";
+ regulator-name = "nvvdd_ldo10,avdd_usb_ic_3v0";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ regulator@14 {
+ reg = <14>;
+ regulator-compatible = "ldo11";
+ regulator-name = "nvvdd_ldo11,vddio_pex_clk,vcom_33,avdd_hdmi";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ regulator@15 {
+ reg = <15>;
+ regulator-compatible = "ldo12";
+ regulator-name = "nvvdd_ldo12,vddio_sdio";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ regulator@16 {
+ reg = <16>;
+ regulator-compatible = "ldo13";
+ regulator-name = "nvvdd_ldo13,vcore_phtn,vdd_af";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ regulator@17 {
+ reg = <17>;
+ regulator-compatible = "ldo14";
+ regulator-name = "nvvdd_ldo14,avdd_vdac";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ regulator@18 {
+ reg = <18>;
+ regulator-compatible = "ldo15";
+ regulator-name = "nvvdd_ldo15,vcore_temp,vddio_hdcp";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ regulator@19 {
+ reg = <19>;
+ regulator-compatible = "ldo16";
+ regulator-name = "nvvdd_ldo16,vdd_dbrtr";
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ };
+
+ regulator@20 {
+ reg = <20>;
+ regulator-compatible = "ldo17";
+ regulator-name = "nvvdd_ldo17,vddio_mipi";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ regulator@21 {
+ reg = <21>;
+ regulator-compatible = "ldo18";
+ regulator-name = "nvvdd_ldo18,vddio_vi,vcore_cam*";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ regulator@22 {
+ reg = <22>;
+ regulator-compatible = "ldo19";
+ regulator-name = "nvvdd_ldo19,avdd_lcd2,vddio_lx";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ regulator@23 {
+ reg = <23>;
+ regulator-compatible = "ldo20";
+ regulator-name = "nvvdd_ldo20,vddio_ddr_1v2,vddio_hsic,vcom_1v2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ regulator@24 {
+ reg = <24>;
+ regulator-compatible = "out5v";
+ regulator-name = "usb0_vbus_reg";
+ };
+
+ regulator@25 {
+ reg = <25>;
+ regulator-compatible = "out33v";
+ regulator-name = "pmu_out3v3";
+ };
+
+ regulator@26 {
+ reg = <26>;
+ regulator-compatible = "bbat";
+ regulator-name = "pmu_bbat";
+ regulator-min-microvolt = <2400000>;
+ regulator-max-microvolt = <2400000>;
+ regulator-always-on;
+ };
+
+ regulator@27 {
+ reg = <27>;
+ regulator-compatible = "sdby";
+ regulator-name = "vdd_aon";
+ regulator-always-on;
+ };
+
+ regulator@28 {
+ reg = <28>;
+ regulator-compatible = "vrtc";
+ regulator-name = "vrtc,pmu_vccadc";
+ regulator-always-on;
+ };
+ };
+ };
+ };
+
+ pmc {
+ nvidia,invert-interrupt;
};
usb@c5000000 {
@@ -284,6 +563,21 @@
bus-width = <8>;
};
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb0_vbus_reg: regulator {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "usb0_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+ };
+
sound {
compatible = "nvidia,tegra-audio-wm8753-whistler",
"nvidia,tegra-audio-wm8753";
--
1.7.0.4
^ permalink raw reply related [flat|nested] 2+ messages in thread
* Re: [PATCH] ARM: dt: tegra: whistler: add regulators
[not found] ` <1344017484-29395-1-git-send-email-swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org>
@ 2012-08-15 16:58 ` Stephen Warren
0 siblings, 0 replies; 2+ messages in thread
From: Stephen Warren @ 2012-08-15 16:58 UTC (permalink / raw)
To: Olof Johansson, Colin Cross
Cc: Mark Brown, Laxman Dewangan,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-tegra-u79uwXL29TY76Z2rM5mHXA, Stephen Warren
On 08/03/2012 12:11 PM, Stephen Warren wrote:
> Whistler uses a Maxim 8907 regulator. Instantiate this.
>
> The voltage settings were derived from the schematic. The only exception
> is the BBAT voltage; the schematic says 1.2v, but the HW can't go that
> low, so use the HW default of 2.4v instead.
>
> Almost all regulators list all driven supply signal names in their
> regulator-names property. The exception is nvvdd_sv3, which is in turn
> named 12 more different names on the schematic, so these were omitted
> for brevity.
Applied to Tegra's for-3.7/dt branch.
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2012-08-15 16:58 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2012-08-03 18:11 [PATCH] ARM: dt: tegra: whistler: add regulators Stephen Warren
[not found] ` <1344017484-29395-1-git-send-email-swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org>
2012-08-15 16:58 ` Stephen Warren
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).