From: Steven Rostedt <rostedt@goodmis.org>
To: Petr Pavlu <petr.pavlu@suse.com>
Cc: mhiramat@kernel.org, mathieu.desnoyers@efficios.com,
zhengyejian1@huawei.com, linux-trace-kernel@vger.kernel.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH 2/2] tracing: Disable events in reverse order of their enable operation
Date: Mon, 27 Nov 2023 12:58:15 -0500 [thread overview]
Message-ID: <20231127125815.4a4d06c6@gandalf.local.home> (raw)
In-Reply-To: <20231127151248.7232-3-petr.pavlu@suse.com>
On Mon, 27 Nov 2023 16:12:48 +0100
Petr Pavlu <petr.pavlu@suse.com> wrote:
> Make the disable operation in __ftrace_event_enable_disable() use the
> reverse order of the respective enable operation.
>
> This has two minor benefits:
> * Disabling of buffered events via trace_buffered_event_disable() is
> done after unregistering the trace event. It closes a small window
> where an event would be still registered and could be hit, but would
> unnecessarily go directly to a ring buffer.
There's little benefit to the above. Going to the ring buffer and reverting
it is just a bit more expensive, but should not be an issue with this small
window.
> * The SOFT_DISABLED flag is now consistently set only when SOFT_MODE is
> also set.
This code is a bit fragile, and I rather not change the logic. There's a
lot of corner cases.
I'm not saying that this is a bad change, I just don't want to add it and
find out later it broke one of the corner cases. To add this would require
an analysis that every input produces the same output with and without this
change.
If you want to make a table showing all inputs between soft_disable and the
flags, and show that the result produces the same updates, I'll then
reconsidered applying this.
Thanks!
-- Steve
>
> Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
> ---
> kernel/trace/trace_events.c | 17 ++++++++++-------
> 1 file changed, 10 insertions(+), 7 deletions(-)
>
> diff --git a/kernel/trace/trace_events.c b/kernel/trace/trace_events.c
> index f29e815ca5b2..5f14d68a0ced 100644
> --- a/kernel/trace/trace_events.c
> +++ b/kernel/trace/trace_events.c
> @@ -633,9 +633,6 @@ static int __ftrace_event_enable_disable(struct trace_event_file *file,
> if (atomic_dec_return(&file->sm_ref) > 0)
> break;
> disable = file->flags & EVENT_FILE_FL_SOFT_DISABLED;
> - clear_bit(EVENT_FILE_FL_SOFT_MODE_BIT, &file->flags);
> - /* Disable use of trace_buffered_event */
> - trace_buffered_event_disable();
> } else
> disable = !(file->flags & EVENT_FILE_FL_SOFT_MODE);
>
> @@ -653,11 +650,17 @@ static int __ftrace_event_enable_disable(struct trace_event_file *file,
>
> call->class->reg(call, TRACE_REG_UNREGISTER, file);
> }
> - /* If in SOFT_MODE, just set the SOFT_DISABLE_BIT, else clear it */
> - if (file->flags & EVENT_FILE_FL_SOFT_MODE)
> - set_bit(EVENT_FILE_FL_SOFT_DISABLED_BIT, &file->flags);
> - else
> +
> + if (soft_disable) {
> + /* Complete going out of SOFT_MODE */
> clear_bit(EVENT_FILE_FL_SOFT_DISABLED_BIT, &file->flags);
> + clear_bit(EVENT_FILE_FL_SOFT_MODE_BIT, &file->flags);
> + /* Disable use of trace_buffered_event */
> + trace_buffered_event_disable();
> + } else if (file->flags & EVENT_FILE_FL_SOFT_MODE) {
> + /* If in SOFT_MODE, just set the SOFT_DISABLE_BIT */
> + set_bit(EVENT_FILE_FL_SOFT_DISABLED_BIT, &file->flags);
> + }
> break;
> case 1:
> /*
next prev parent reply other threads:[~2023-11-27 17:57 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-11-27 15:12 [PATCH 0/2] tracing: Simplify and fix "buffered event" synchronization Petr Pavlu
2023-11-27 15:12 ` [PATCH 1/2] " Petr Pavlu
2023-11-27 17:41 ` Steven Rostedt
2023-11-28 15:05 ` Petr Pavlu
2023-11-28 15:27 ` Steven Rostedt
2023-11-29 9:22 ` Petr Pavlu
2023-11-29 14:58 ` Steven Rostedt
2023-12-01 14:17 ` Petr Pavlu
2023-12-01 14:46 ` Steven Rostedt
2023-12-05 16:16 ` Petr Pavlu
2023-11-27 15:12 ` [PATCH 2/2] tracing: Disable events in reverse order of their enable operation Petr Pavlu
2023-11-27 17:58 ` Steven Rostedt [this message]
2023-11-28 15:06 ` Petr Pavlu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20231127125815.4a4d06c6@gandalf.local.home \
--to=rostedt@goodmis.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-trace-kernel@vger.kernel.org \
--cc=mathieu.desnoyers@efficios.com \
--cc=mhiramat@kernel.org \
--cc=petr.pavlu@suse.com \
--cc=zhengyejian1@huawei.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox