Linux USB
 help / color / mirror / Atom feed
From: Chunfeng Yun <chunfeng.yun@mediatek.com>
To: sunjg79@163.com
Cc: mathias.nyman@intel.com, gregkh@linuxfoundation.org,
	robh+dt@kernel.org, shawn.guo@linaro.org,
	xuejiancheng@hisilicon.com, linux-usb@vger.kernel.org,
	devicetree@vger.kernel.org, Jianguo Sun <sunjianguo1@huawei.com>
Subject: [2/2] xhci: hisilicon: support HiSilicon STB xHCI host controller
Date: Fri, 4 May 2018 17:59:40 +0800	[thread overview]
Message-ID: <1525427980.25162.36.camel@mhfsdcap03> (raw)

Hi Jianguo,

On Fri, 2018-05-04 at 17:20 +0800, sunjg79@163.com wrote:
> From: Jianguo Sun <sunjianguo1@huawei.com>
> 
> This commit adds support for HiSilicon STB xHCI host controller.
> 
> Signed-off-by: Jianguo Sun <sunjianguo1@huawei.com>
> ---
>  drivers/usb/host/Kconfig      |   7 +
>  drivers/usb/host/Makefile     |   1 +
>  drivers/usb/host/xhci-histb.c | 409 ++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 417 insertions(+)
>  create mode 100644 drivers/usb/host/xhci-histb.c
> 
> diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
> index 5d958da..c813fc4 100644
> --- a/drivers/usb/host/Kconfig
> +++ b/drivers/usb/host/Kconfig
> @@ -52,6 +52,13 @@ config USB_XHCI_PLATFORM
>  
>  	  If unsure, say N.
>  
> +config USB_XHCI_HISTB
> +	tristate "xHCI support for HiSilicon STB SoCs"
> +	depends on USB_XHCI_PLATFORM && (ARCH_HISI || COMPILE_TEST)
> +	help
> +	  Say 'Y' to enable the support for the xHCI host controller
> +	  found in HiSilicon STB SoCs.
> +
>  config USB_XHCI_MTK
>  	tristate "xHCI support for MediaTek SoCs"
>  	select MFD_SYSCON
> diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
> index 8a8cffe..9b669c9 100644
> --- a/drivers/usb/host/Makefile
> +++ b/drivers/usb/host/Makefile
> @@ -74,6 +74,7 @@ obj-$(CONFIG_USB_FHCI_HCD)	+= fhci.o
>  obj-$(CONFIG_USB_XHCI_HCD)	+= xhci-hcd.o
>  obj-$(CONFIG_USB_XHCI_PCI)	+= xhci-pci.o
>  obj-$(CONFIG_USB_XHCI_PLATFORM) += xhci-plat-hcd.o
> +obj-$(CONFIG_USB_XHCI_HISTB)	+= xhci-histb.o
>  obj-$(CONFIG_USB_XHCI_MTK)	+= xhci-mtk.o
>  obj-$(CONFIG_USB_XHCI_TEGRA)	+= xhci-tegra.o
>  obj-$(CONFIG_USB_SL811_HCD)	+= sl811-hcd.o
> diff --git a/drivers/usb/host/xhci-histb.c b/drivers/usb/host/xhci-histb.c
> new file mode 100644
> index 0000000..5ec549f
> --- /dev/null
> +++ b/drivers/usb/host/xhci-histb.c
> @@ -0,0 +1,409 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * xHCI host controller driver for HiSilicon STB SoCs
> + *
> + * Copyright (C) 2017-2018 HiSilicon Co., Ltd. http://www.hisilicon.com
> + *
> + * Authors: Jianguo Sun <sunjianguo1@huawei.com>
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
No need anymore if SPDX-License-Identifier is provided
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/dma-mapping.h>
> +#include <linux/kernel.h>
> +#include <linux/mfd/syscon.h>
Not used
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/regmap.h>
ditto
> +#include <linux/reset.h>
> +
> +#include "xhci.h"
> +
> +#define GTXTHRCFG		0xc108
> +#define GRXTHRCFG		0xc10c
> +#define REG_GUSB2PHYCFG0	0xc200
> +#define BIT_UTMI_8_16		BIT(3)
> +#define BIT_UTMI_ULPI		BIT(4)
> +#define BIT_FREECLK_EXIST	BIT(30)
> +
> +#define REG_GUSB3PIPECTL0	0xc2c0
> +#define USB3_DEEMPHASIS_MASK	GENMASK(2, 1)
> +#define USB3_DEEMPHASIS0	BIT(1)
> +#define USB3_TX_MARGIN1		BIT(4)
> +
> +struct xhci_hcd_histb {
> +	struct device		*dev;
> +	struct usb_hcd		*hcd;
> +	void __iomem		*ctrl;
> +	struct clk		*bus_clk;
> +	struct clk		*utmi_clk;
> +	struct clk		*pipe_clk;
> +	struct clk		*suspend_clk;
> +	struct reset_control	*soft_reset;
> +};
> +
> +static inline struct xhci_hcd_histb *hcd_to_histb(struct usb_hcd *hcd)
> +{
> +	return dev_get_drvdata(hcd->self.controller);
> +}
> +
> +static int xhci_histb_config(struct xhci_hcd_histb *histb)
> +{
> +	struct device_node *np = histb->dev->of_node;
> +	u32 regval;
> +
> +	if (of_property_match_string(np, "phys-names", "inno") >= 0) {
> +		/* USB2 PHY chose ulpi 8bit interface */
> +		regval = readl(histb->ctrl + REG_GUSB2PHYCFG0);
> +		regval &= ~BIT_UTMI_ULPI;
> +		regval &= ~(BIT_UTMI_8_16);
> +		regval &= ~BIT_FREECLK_EXIST;
> +		writel(regval, histb->ctrl + REG_GUSB2PHYCFG0);
> +	}
> +
> +	if (of_property_match_string(np, "phys-names", "combo") >= 0) {
> +		/*
> +		 * write 0x010c0012 to GUSB3PIPECTL0
> +		 * GUSB3PIPECTL0[5:3] = 010 : Tx Margin = 900mV ,
> +		 * decrease TX voltage
> +		 * GUSB3PIPECTL0[2:1] = 01 : Tx Deemphasis = -3.5dB,
> +		 * refer to xHCI spec
> +		 */
> +		regval = readl(histb->ctrl + REG_GUSB3PIPECTL0);
> +		regval &= ~USB3_DEEMPHASIS_MASK;
> +		regval |= USB3_DEEMPHASIS0;
> +		regval |= USB3_TX_MARGIN1;
> +		writel(regval, histb->ctrl + REG_GUSB3PIPECTL0);
> +	}
> +
> +	writel(0x23100000, histb->ctrl + GTXTHRCFG);
> +	writel(0x23100000, histb->ctrl + GRXTHRCFG);
> +
> +	return 0;
> +}
> +
> +static int xhci_histb_clks_get(struct xhci_hcd_histb *histb)
> +{
> +	struct device *dev = histb->dev;
> +
> +	histb->bus_clk = devm_clk_get(dev, "bus");
> +	if (IS_ERR(histb->bus_clk)) {
> +		dev_err(dev, "fail to get bus clk\n");
> +		return PTR_ERR(histb->bus_clk);
> +	}
> +
> +	histb->utmi_clk = devm_clk_get(dev, "utmi");
> +	if (IS_ERR(histb->utmi_clk)) {
> +		dev_err(dev, "fail to get utmi clk\n");
> +		return PTR_ERR(histb->utmi_clk);
> +	}
> +
> +	histb->pipe_clk = devm_clk_get(dev, "pipe");
> +	if (IS_ERR(histb->pipe_clk)) {
> +		dev_err(dev, "fail to get pipe clk\n");
> +		return PTR_ERR(histb->pipe_clk);
> +	}
> +
> +	histb->suspend_clk = devm_clk_get(dev, "suspend");
> +	if (IS_ERR(histb->suspend_clk)) {
> +		dev_err(dev, "fail to get suspend clk\n");
> +		return PTR_ERR(histb->suspend_clk);
> +	}
> +
> +	return 0;
> +}
> +
> +static int xhci_histb_host_enable(struct xhci_hcd_histb *histb)
> +{
> +	int ret;
> +
> +	ret = clk_prepare_enable(histb->bus_clk);
> +	if (ret) {
> +		dev_err(histb->dev, "failed to enable bus clk\n");
> +		return ret;
> +	}
> +
> +	ret = clk_prepare_enable(histb->utmi_clk);
> +	if (ret) {
> +		dev_err(histb->dev, "failed to enable utmi clk\n");
> +		goto err_utmi_clk;
> +	}
> +
> +	ret = clk_prepare_enable(histb->pipe_clk);
> +	if (ret) {
> +		dev_err(histb->dev, "failed to enable pipe clk\n");
> +		goto err_pipe_clk;
> +	}
> +
> +	ret = clk_prepare_enable(histb->suspend_clk);
> +	if (ret) {
> +		dev_err(histb->dev, "failed to enable suspend clk\n");
> +		goto err_suspend_clk;
> +	}
> +
> +	reset_control_deassert(histb->soft_reset);
> +
> +	return 0;
> +
> +err_suspend_clk:
> +	clk_disable_unprepare(histb->pipe_clk);
> +err_pipe_clk:
> +	clk_disable_unprepare(histb->utmi_clk);
> +err_utmi_clk:
> +	clk_disable_unprepare(histb->bus_clk);
> +
> +	return ret;
> +}
> +
> +static void xhci_histb_host_disable(struct xhci_hcd_histb *histb)
> +{
> +	reset_control_assert(histb->soft_reset);
> +
> +	clk_disable_unprepare(histb->suspend_clk);
> +	clk_disable_unprepare(histb->pipe_clk);
> +	clk_disable_unprepare(histb->utmi_clk);
> +	clk_disable_unprepare(histb->bus_clk);
> +}
> +
> +static void xhci_histb_quirks(struct device *dev, struct xhci_hcd *xhci)
> +{
> +	/*
> +	 * As of now platform drivers don't provide MSI support so we ensure
> +	 * here that the generic code does not try to make a pci_dev from our
> +	 * dev struct in order to setup MSI
> +	 */
> +	xhci->quirks |= XHCI_PLAT;
> +}
> +
> +/* called during probe() after chip reset completes */
> +static int xhci_histb_setup(struct usb_hcd *hcd)
> +{
> +	struct xhci_hcd_histb *histb = hcd_to_histb(hcd);
> +	int ret;
> +
> +	if (usb_hcd_is_primary_hcd(hcd)) {
> +		ret = xhci_histb_config(histb);
> +		if (ret)
> +			return ret;
> +	}
> +
> +	ret = xhci_gen_setup(hcd, xhci_histb_quirks);
> +	if (ret)
> +		return ret;
no need test @ret here
> +
> +	return ret;
> +}
> +
> +static const struct xhci_driver_overrides xhci_histb_overrides __initconst = {
> +	.reset = xhci_histb_setup,
> +};
> +
> +static struct hc_driver __read_mostly xhci_histb_hc_driver;
> +static int xhci_histb_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct xhci_hcd_histb *histb;
> +	const struct hc_driver *driver;
> +	struct usb_hcd *hcd;
> +	struct xhci_hcd *xhci;
> +	struct resource *res;
> +	int irq;
> +	int ret = -ENODEV;
> +
> +	if (usb_disabled())
> +		return -ENODEV;
> +
> +	driver = &xhci_histb_hc_driver;
> +	histb = devm_kzalloc(dev, sizeof(*histb), GFP_KERNEL);
> +	if (!histb)
> +		return -ENOMEM;
> +
> +	histb->dev = dev;
> +
> +	irq = platform_get_irq(pdev, 0);
> +	if (irq < 0)
> +		return irq;
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	histb->ctrl = devm_ioremap_resource(&pdev->dev, res);
> +	if (IS_ERR(histb->ctrl))
> +		return PTR_ERR(histb->ctrl);
> +
> +	ret = xhci_histb_clks_get(histb);
> +	if (ret)
> +		return ret;
> +
> +	histb->soft_reset = devm_reset_control_get(dev, "soft");
> +	if (IS_ERR(histb->soft_reset)) {
> +		dev_err(dev, "failed to get soft reset\n");
> +		return PTR_ERR(histb->soft_reset);
> +	}
> +
> +	pm_runtime_enable(dev);
> +	pm_runtime_get_sync(dev);
> +	device_enable_async_suspend(dev);
> +
> +	/* Initialize dma_mask and coherent_dma_mask to 32-bits */
> +	ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(32));
> +	if (ret)
> +		return ret;
> +
> +	hcd = usb_create_hcd(driver, dev, dev_name(dev));
> +	if (!hcd) {
> +		ret = -ENOMEM;
> +		goto disable_pm;
> +	}
> +
> +	hcd->regs = histb->ctrl;
> +	hcd->rsrc_start = res->start;
> +	hcd->rsrc_len = resource_size(res);
> +
> +	histb->hcd = hcd;
> +	dev_set_drvdata(hcd->self.controller, histb);
> +
> +	ret = xhci_histb_host_enable(histb);
> +	if (ret)
> +		goto put_hcd;
> +
> +	xhci = hcd_to_xhci(hcd);
> +
> +	device_wakeup_enable(hcd->self.controller);
> +
> +	xhci->main_hcd = hcd;
> +	xhci->shared_hcd = usb_create_shared_hcd(driver, dev, dev_name(dev),
> +						 hcd);
> +	if (!xhci->shared_hcd) {
> +		ret = -ENOMEM;
> +		goto disable_host;
> +	}
> +
> +	ret = usb_add_hcd(hcd, irq, IRQF_SHARED);
> +	if (ret)
> +		goto put_usb3_hcd;
> +
> +	if (HCC_MAX_PSA(xhci->hcc_params) >= 4)
> +		xhci->shared_hcd->can_do_streams = 1;
> +
> +	ret = usb_add_hcd(xhci->shared_hcd, irq, IRQF_SHARED);
> +	if (ret)
> +		goto dealloc_usb2_hcd;
> +
> +	device_enable_async_suspend(dev);
> +	pm_runtime_put_noidle(dev);
> +
> +	/*
> +	 * Prevent runtime pm from being on as default, users should enable
> +	 * runtime pm using power/control in sysfs.
> +	 */
> +	pm_runtime_forbid(dev);
> +
Are you sure make use of the default value xhci->imod_interval == 0 ?

> +	return 0;
> +
> +dealloc_usb2_hcd:
> +	usb_remove_hcd(hcd);
> +put_usb3_hcd:
> +	usb_put_hcd(xhci->shared_hcd);
> +disable_host:
> +	xhci_histb_host_disable(histb);
> +put_hcd:
> +	usb_put_hcd(hcd);
> +disable_pm:
> +	pm_runtime_put_sync(dev);
> +	pm_runtime_disable(dev);
> +
> +	return ret;
> +}
> +
> +static int xhci_histb_remove(struct platform_device *dev)
> +{
> +	struct xhci_hcd_histb *histb = platform_get_drvdata(dev);
> +	struct usb_hcd *hcd = histb->hcd;
> +	struct xhci_hcd	*xhci = hcd_to_xhci(hcd);
> +
> +	xhci->xhc_state |= XHCI_STATE_REMOVING;
> +
> +	usb_remove_hcd(xhci->shared_hcd);
> +	device_wakeup_disable(&dev->dev);
> +
> +	usb_remove_hcd(hcd);
> +	usb_put_hcd(xhci->shared_hcd);
> +
> +	xhci_histb_host_disable(histb);
> +	usb_put_hcd(hcd);
> +	pm_runtime_put_sync(&dev->dev);
> +	pm_runtime_disable(&dev->dev);
> +
> +	return 0;
> +}
> +
> +static int __maybe_unused xhci_histb_suspend(struct device *dev)
> +{
> +	struct xhci_hcd_histb *histb = dev_get_drvdata(dev);
> +	struct usb_hcd *hcd = histb->hcd;
> +	struct xhci_hcd	*xhci = hcd_to_xhci(hcd);
> +	int ret;
> +
> +	ret = xhci_suspend(xhci, device_may_wakeup(dev));
> +
> +	if (!device_may_wakeup(dev))
> +		xhci_histb_host_disable(histb);
> +
> +	return ret;
> +}
> +
> +static int __maybe_unused xhci_histb_resume(struct device *dev)
> +{
> +	struct xhci_hcd_histb *histb = dev_get_drvdata(dev);
> +	struct usb_hcd *hcd = histb->hcd;
> +	struct xhci_hcd *xhci = hcd_to_xhci(hcd);
> +
> +	if (!device_may_wakeup(dev))
> +		xhci_histb_host_enable(histb);
> +
> +	return xhci_resume(xhci, 0);
> +}
> +
> +static const struct dev_pm_ops xhci_histb_pm_ops = {
> +	SET_SYSTEM_SLEEP_PM_OPS(xhci_histb_suspend, xhci_histb_resume)
> +};
> +#define DEV_PM_OPS (IS_ENABLED(CONFIG_PM) ? &xhci_histb_pm_ops : NULL)
> +
> +#ifdef CONFIG_OF
> +static const struct of_device_id histb_xhci_of_match[] = {
> +	{ .compatible = "hisilicon,hi3798cv200-xhci"},
> +	{ },
> +};
> +MODULE_DEVICE_TABLE(of, histb_xhci_of_match);
> +#endif
> +
> +static struct platform_driver histb_xhci_driver = {
> +	.probe	= xhci_histb_probe,
> +	.remove	= xhci_histb_remove,
> +	.driver	= {
> +		.name = "xhci-histb",
> +		.pm = DEV_PM_OPS,
> +		.of_match_table = of_match_ptr(histb_xhci_of_match),
> +	},
> +};
> +MODULE_ALIAS("platform:xhci-histb");
> +
> +static int __init xhci_histb_init(void)
> +{
> +	xhci_init_driver(&xhci_histb_hc_driver, &xhci_histb_overrides);
> +	return platform_driver_register(&histb_xhci_driver);
> +}
> +module_init(xhci_histb_init);
> +
> +static void __exit xhci_histb_exit(void)
> +{
> +	platform_driver_unregister(&histb_xhci_driver);
> +}
> +module_exit(xhci_histb_exit);
> +
> +MODULE_DESCRIPTION("HiSilicon STB xHCI Host Controller Driver");
> +MODULE_LICENSE("GPL v2");
---
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

             reply	other threads:[~2018-05-04  9:59 UTC|newest]

Thread overview: 3+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-05-04  9:59 Chunfeng Yun [this message]
  -- strict thread matches above, loose matches on Subject: below --
2018-05-04 10:32 [2/2] xhci: hisilicon: support HiSilicon STB xHCI host controller sunjg79
2018-05-04  9:20 sunjg79

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1525427980.25162.36.camel@mhfsdcap03 \
    --to=chunfeng.yun@mediatek.com \
    --cc=devicetree@vger.kernel.org \
    --cc=gregkh@linuxfoundation.org \
    --cc=linux-usb@vger.kernel.org \
    --cc=mathias.nyman@intel.com \
    --cc=robh+dt@kernel.org \
    --cc=shawn.guo@linaro.org \
    --cc=sunjg79@163.com \
    --cc=sunjianguo1@huawei.com \
    --cc=xuejiancheng@hisilicon.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox