Re: [PATCH v4 04/11] usb: xhci-rcar: convert to readl_poll_timeout_atomic()

[Chunfeng Yun <chunfeng.yun@mediatek.com>]

On Wed, 2020-09-23 at 08:47 +0000, Yoshihiro Shimoda wrote:
> Hi Chungeng,
> 
> Thank you for the patch!
> 
> > From: Chunfeng Yun, Sent: Monday, September 21, 2020 3:13 PM
> > 
> > Use readl_poll_timeout_atomic() to simplify code
> > 
> > Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
> > Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
> > Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
> > ---
> > v4: changes
> >     1. remove unnecessary parentheses suggested by Yoshihiro
> >     2. fix the wrong return value suggested by Yoshihiro & Daniel
> > 
> > v2~v3: no changes
> > ---
> >  drivers/usb/host/xhci-rcar.c | 43 ++++++++++++-------------------------------
> >  1 file changed, 12 insertions(+), 31 deletions(-)
> > 
> > diff --git a/drivers/usb/host/xhci-rcar.c b/drivers/usb/host/xhci-rcar.c
> > index c1025d3..1bc4fe7 100644
> > --- a/drivers/usb/host/xhci-rcar.c
> > +++ b/drivers/usb/host/xhci-rcar.c
> > @@ -6,6 +6,7 @@
> >   */
> > 
> >  #include <linux/firmware.h>
> > +#include <linux/iopoll.h>
> >  #include <linux/module.h>
> >  #include <linux/platform_device.h>
> >  #include <linux/of.h>
> > @@ -127,8 +128,7 @@ static int xhci_rcar_download_firmware(struct usb_hcd *hcd)
> >  	void __iomem *regs = hcd->regs;
> >  	struct xhci_plat_priv *priv = hcd_to_xhci_priv(hcd);
> >  	const struct firmware *fw;
> > -	int retval, index, j, time;
> > -	int timeout = 10000;
> > +	int retval, index, j;
> >  	u32 data, val, temp;
> >  	u32 quirks = 0;
> >  	const struct soc_device_attribute *attr;
> > @@ -166,32 +166,19 @@ static int xhci_rcar_download_firmware(struct usb_hcd *hcd)
> >  		temp |= RCAR_USB3_DL_CTRL_FW_SET_DATA0;
> >  		writel(temp, regs + RCAR_USB3_DL_CTRL);
> > 
> > -		for (time = 0; time < timeout; time++) {
> > -			val = readl(regs + RCAR_USB3_DL_CTRL);
> > -			if ((val & RCAR_USB3_DL_CTRL_FW_SET_DATA0) == 0)
> > -				break;
> > -			udelay(1);
> > -		}
> > -		if (time == timeout) {
> > -			retval = -ETIMEDOUT;
> > +		retval = readl_poll_timeout_atomic(regs + RCAR_USB3_DL_CTRL,
> > +				val, !(val & RCAR_USB3_DL_CTRL_FW_SET_DATA0),
> > +				1, 10000);
> > +		if (retval < 0)
> >  			break;
> > -		}
> >  	}
> > 
> >  	temp = readl(regs + RCAR_USB3_DL_CTRL);
> >  	temp &= ~RCAR_USB3_DL_CTRL_ENABLE;
> >  	writel(temp, regs + RCAR_USB3_DL_CTRL);
> > 
> > -	for (time = 0; time < timeout; time++) {
> > -		val = readl(regs + RCAR_USB3_DL_CTRL);
> > -		if (val & RCAR_USB3_DL_CTRL_FW_SUCCESS) {
> > -			retval = 0;
> > -			break;
> > -		}
> > -		udelay(1);
> > -	}
> > -	if (time == timeout)
> > -		retval = -ETIMEDOUT;
> > +	retval = readl_poll_timeout_atomic((regs + RCAR_USB3_DL_CTRL),
> 
> We can also remove these unnecessary parentheses like below.
Ok, will remove it, thanks a lot

> 
> +	retval = readl_poll_timeout_atomic(regs + RCAR_USB3_DL_CTRL,
> 
> After fixed this:
> 
> Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
> 
> Best regards,
> Yoshihiro Shimoda
>