From: Peter Chen <peter.chen@nxp.com>
To: Kishon Vijay Abraham I <kishon@ti.com>
Cc: "linux-usb@vger.kernel.org" <linux-usb@vger.kernel.org>,
dl-linux-imx <linux-imx@nxp.com>,
"gregkh@linuxfoundation.org" <gregkh@linuxfoundation.org>
Subject: Re: [PATCH 1/1] phy: freescale: imx8qm-usb3: add imx8qm USB3 PHY
Date: Tue, 31 Dec 2019 01:14:03 +0000 [thread overview]
Message-ID: <20191231011400.GA22207@b29397-desktop> (raw)
In-Reply-To: <8bf4c685-f2e7-f500-bd5e-0421f3dd2903@ti.com>
On 19-12-30 17:39:48, Kishon Vijay Abraham I wrote:
> Hi,
>
> On 27/12/19 11:32 AM, Peter Chen wrote:
> > This USB3 PHY is used to support USB3 controller at imx8qm and imx8qxp
> > SoCs.
> >
> > Signed-off-by: Peter Chen <peter.chen@nxp.com>
> > ---
> > drivers/phy/freescale/Kconfig | 8 +
> > drivers/phy/freescale/Makefile | 1 +
> > drivers/phy/freescale/phy-fsl-imx8qm-usb3.c | 254 ++++++++++++++++++++
> > 3 files changed, 263 insertions(+)
> > create mode 100644 drivers/phy/freescale/phy-fsl-imx8qm-usb3.c
> >
> > diff --git a/drivers/phy/freescale/Kconfig b/drivers/phy/freescale/Kconfig
> > index 320630ffe3cd..4282f07784f8 100644
> > --- a/drivers/phy/freescale/Kconfig
> > +++ b/drivers/phy/freescale/Kconfig
> > @@ -14,3 +14,11 @@ config PHY_MIXEL_MIPI_DPHY
> > help
> > Enable this to add support for the Mixel DSI PHY as found
> > on NXP's i.MX8 family of SOCs.
> > +
> > +config PHY_FSL_IMX8QM_USB
> > + tristate "Freescale i.MX8QM USB3 PHY"
> > + depends on OF && ARCH_MXC
> > + select GENERIC_PHY
> > + help
> > + Enable this to add support for the USB3 PHY as found
> > + on NXP's i.MX8QM family of SOCs.
> > diff --git a/drivers/phy/freescale/Makefile b/drivers/phy/freescale/Makefile
> > index 1d02e3869b45..dcab710fb90d 100644
> > --- a/drivers/phy/freescale/Makefile
> > +++ b/drivers/phy/freescale/Makefile
> > @@ -1,3 +1,4 @@
> > # SPDX-License-Identifier: GPL-2.0-only
> > obj-$(CONFIG_PHY_FSL_IMX8MQ_USB) += phy-fsl-imx8mq-usb.o
> > obj-$(CONFIG_PHY_MIXEL_MIPI_DPHY) += phy-fsl-imx8-mipi-dphy.o
> > +obj-$(CONFIG_PHY_FSL_IMX8QM_USB) += phy-fsl-imx8qm-usb3.o
> > diff --git a/drivers/phy/freescale/phy-fsl-imx8qm-usb3.c b/drivers/phy/freescale/phy-fsl-imx8qm-usb3.c
> > new file mode 100644
> > index 000000000000..19ab6aa3271b
> > --- /dev/null
> > +++ b/drivers/phy/freescale/phy-fsl-imx8qm-usb3.c
> > @@ -0,0 +1,254 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/* Copyright (c) 2019 NXP. */
> > +
> > +#include <linux/clk.h>
> > +#include <linux/io.h>
> > +#include <linux/module.h>
> > +#include <linux/phy/phy.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/delay.h>
> > +
> > +/* PHY register definition */
> > +#define PHY_PMA_CMN_CTRL1 (0xC800 * 4)
>
> Please use regmap for this.
Hi Kishon,
Thanks for reviewing. These registers are dedicated for USB PHY,
so it doesn't need to use regmap.
> > +#define TB_ADDR_CMN_DIAG_HSCLK_SEL (0x01e0 * 4)
> > +#define TB_ADDR_CMN_PLL0_VCOCAL_INIT_TMR (0x0084 * 4)
> > +#define TB_ADDR_CMN_PLL0_VCOCAL_ITER_TMR (0x0085 * 4)
> > +#define TB_ADDR_CMN_PLL0_INTDIV (0x0094 * 4)
> > +#define TB_ADDR_CMN_PLL0_FRACDIV (0x0095 * 4)
> > +#define TB_ADDR_CMN_PLL0_HIGH_THR (0x0096 * 4)
> > +#define TB_ADDR_CMN_PLL0_SS_CTRL1 (0x0098 * 4)
> > +#define TB_ADDR_CMN_PLL0_SS_CTRL2 (0x0099 * 4)
> > +#define TB_ADDR_CMN_PLL0_DSM_DIAG (0x0097 * 4)
> > +#define TB_ADDR_CMN_DIAG_PLL0_OVRD (0x01c2 * 4)
> > +#define TB_ADDR_CMN_DIAG_PLL0_FBH_OVRD (0x01c0 * 4)
> > +#define TB_ADDR_CMN_DIAG_PLL0_FBL_OVRD (0x01c1 * 4)
> > +#define TB_ADDR_CMN_DIAG_PLL0_V2I_TUNE (0x01C5 * 4)
> > +#define TB_ADDR_CMN_DIAG_PLL0_CP_TUNE (0x01C6 * 4)
> > +#define TB_ADDR_CMN_DIAG_PLL0_LF_PROG (0x01C7 * 4)
> > +#define TB_ADDR_CMN_DIAG_PLL0_TEST_MODE (0x01c4 * 4)
> > +#define TB_ADDR_CMN_PSM_CLK_CTRL (0x0061 * 4)
> > +#define TB_ADDR_XCVR_DIAG_RX_LANE_CAL_RST_TMR (0x40ea * 4)
> > +#define TB_ADDR_XCVR_PSM_RCTRL (0x4001 * 4)
> > +#define TB_ADDR_TX_PSC_A0 (0x4100 * 4)
> > +#define TB_ADDR_TX_PSC_A1 (0x4101 * 4)
> > +#define TB_ADDR_TX_PSC_A2 (0x4102 * 4)
> > +#define TB_ADDR_TX_PSC_A3 (0x4103 * 4)
> > +#define TB_ADDR_TX_DIAG_ECTRL_OVRD (0x41f5 * 4)
> > +#define TB_ADDR_TX_PSC_CAL (0x4106 * 4)
> > +#define TB_ADDR_TX_PSC_RDY (0x4107 * 4)
> > +#define TB_ADDR_RX_PSC_A0 (0x8000 * 4)
> > +#define TB_ADDR_RX_PSC_A1 (0x8001 * 4)
> > +#define TB_ADDR_RX_PSC_A2 (0x8002 * 4)
> > +#define TB_ADDR_RX_PSC_A3 (0x8003 * 4)
> > +#define TB_ADDR_RX_PSC_CAL (0x8006 * 4)
> > +#define TB_ADDR_RX_PSC_RDY (0x8007 * 4)
> > +#define TB_ADDR_TX_TXCC_MGNLS_MULT_000 (0x4058 * 4)
> > +#define TB_ADDR_TX_DIAG_BGREF_PREDRV_DELAY (0x41e7 * 4)
> > +#define TB_ADDR_RX_SLC_CU_ITER_TMR (0x80e3 * 4)
> > +#define TB_ADDR_RX_SIGDET_HL_FILT_TMR (0x8090 * 4)
> > +#define TB_ADDR_RX_SAMP_DAC_CTRL (0x8058 * 4)
> > +#define TB_ADDR_RX_DIAG_SIGDET_TUNE (0x81dc * 4)
> > +#define TB_ADDR_RX_DIAG_LFPSDET_TUNE2 (0x81df * 4)
> > +#define TB_ADDR_RX_DIAG_BS_TM (0x81f5 * 4)
> > +#define TB_ADDR_RX_DIAG_DFE_CTRL1 (0x81d3 * 4)
> > +#define TB_ADDR_RX_DIAG_ILL_IQE_TRIM4 (0x81c7 * 4)
> > +#define TB_ADDR_RX_DIAG_ILL_E_TRIM0 (0x81c2 * 4)
> > +#define TB_ADDR_RX_DIAG_ILL_IQ_TRIM0 (0x81c1 * 4)
> > +#define TB_ADDR_RX_DIAG_ILL_IQE_TRIM6 (0x81c9 * 4)
> > +#define TB_ADDR_RX_DIAG_RXFE_TM3 (0x81f8 * 4)
> > +#define TB_ADDR_RX_DIAG_RXFE_TM4 (0x81f9 * 4)
> > +#define TB_ADDR_RX_DIAG_LFPSDET_TUNE (0x81dd * 4)
> > +#define TB_ADDR_RX_DIAG_DFE_CTRL3 (0x81d5 * 4)
> > +#define TB_ADDR_RX_DIAG_SC2C_DELAY (0x81e1 * 4)
> > +#define TB_ADDR_RX_REE_VGA_GAIN_NODFE (0x81bf * 4)
> > +#define TB_ADDR_XCVR_PSM_CAL_TMR (0x4002 * 4)
> > +#define TB_ADDR_XCVR_PSM_A0BYP_TMR (0x4004 * 4)
> > +#define TB_ADDR_XCVR_PSM_A0IN_TMR (0x4003 * 4)
> > +#define TB_ADDR_XCVR_PSM_A1IN_TMR (0x4005 * 4)
> > +#define TB_ADDR_XCVR_PSM_A2IN_TMR (0x4006 * 4)
> > +#define TB_ADDR_XCVR_PSM_A3IN_TMR (0x4007 * 4)
> > +#define TB_ADDR_XCVR_PSM_A4IN_TMR (0x4008 * 4)
> > +#define TB_ADDR_XCVR_PSM_A5IN_TMR (0x4009 * 4)
> > +#define TB_ADDR_XCVR_PSM_A0OUT_TMR (0x400a * 4)
> > +#define TB_ADDR_XCVR_PSM_A1OUT_TMR (0x400b * 4)
> > +#define TB_ADDR_XCVR_PSM_A2OUT_TMR (0x400c * 4)
> > +#define TB_ADDR_XCVR_PSM_A3OUT_TMR (0x400d * 4)
> > +#define TB_ADDR_XCVR_PSM_A4OUT_TMR (0x400e * 4)
> > +#define TB_ADDR_XCVR_PSM_A5OUT_TMR (0x400f * 4)
> > +#define TB_ADDR_TX_RCVDET_EN_TMR (0x4122 * 4)
> > +#define TB_ADDR_TX_RCVDET_ST_TMR (0x4123 * 4)
> > +#define TB_ADDR_XCVR_DIAG_LANE_FCM_EN_MGN_TMR (0x40f2 * 4)
> > +#define TB_ADDR_TX_RCVDETSC_CTRL (0x4124 * 4)
> > +
> > +/* TB_ADDR_TX_RCVDETSC_CTRL */
> > +#define RXDET_IN_P3_32KHZ (1 << 0)
> > +
> > +struct imx8qm_usb_phy {
> > + struct phy *phy;
> > + struct clk *clk;
> > + void __iomem *base;
> > +};
> > +
> > +static int imx8qm_phy_power_on(struct phy *phy)
> > +{
> > + struct imx8qm_usb_phy *imx_phy = phy_get_drvdata(phy);
> > + int ret;
> > + u32 value;
> > + void __iomem *regs = imx_phy->base;
> > +
> > + ret = clk_prepare_enable(imx_phy->clk);
> > + if (ret)
> > + return ret;
> > +
> > + /* Below bringup sequence is from PHY's User Guide */
> > + writel(0x0830, regs + PHY_PMA_CMN_CTRL1);
>
> I'm not sure what these registers represent. But if they are programming
> clocks (multiplier, divider etc..), it must be modeled as clocks.
>
In fact, there is no detail explanation for this Cadence PHY. We only
write the value the user guide suggested.
> We could also keep all these calibration values in a table similar to
> what is done in phy/cadence/phy-cadence-sierra.c. That will help to
> seamlessly add other modes (if supported by PHY).
>
From this PHY spec, this PHY is only for USB. See below:
Features
• Supported standards: USB 3.1 (SuperSpeed only), USB2 (optional)
• Consists of one USB3 SS lane and (optional) USB2 lane
• Contains a USB3 SS PIPE-based PCS
• PHY-level logic delivered as ‘soft’ RTL
• PMA delivered as ‘hard’ macros
• Selectable 16- or 32-bit PIPE interface for USB3
• PIPE interface is compliant to PIPE revision 4.0
• Optional UTMI interface for USB2 PHY
And I confirmed with Cadence's PHY team, we can't re-use
phy-cadence-sierra for this PHY. See below:
Hi Peter,
Thanks for sharing the sequences.
The PHY NxP is using is a Legacy module. The Sierra and
Torrent are later evolutions from Legacy.
Hence there sequence overlap is minimal, meaning we cannot
reuse either of the PHY drivers.
Regards,
Milind
--
Thanks,
Peter Chen
next prev parent reply other threads:[~2019-12-31 1:16 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-12-27 6:02 [PATCH 1/1] phy: freescale: imx8qm-usb3: add imx8qm USB3 PHY Peter Chen
2019-12-30 12:09 ` Kishon Vijay Abraham I
2019-12-31 1:14 ` Peter Chen [this message]
2019-12-31 8:17 ` Kishon Vijay Abraham I
2020-01-02 2:35 ` Peter Chen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191231011400.GA22207@b29397-desktop \
--to=peter.chen@nxp.com \
--cc=gregkh@linuxfoundation.org \
--cc=kishon@ti.com \
--cc=linux-imx@nxp.com \
--cc=linux-usb@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox