[PATCH AUTOSEL 5.4 041/330] USB: serial: mos7840: fix probe error handling

[Sasha Levin <sashal@kernel.org>]

From: Johan Hovold <johan@kernel.org>

[ Upstream commit 960fbd1ca584a5b4cd818255769769d42bfc6dbe ]

The driver would return success and leave the port structures
half-initialised if any of the register accesses during probe fails.

This would specifically leave the port control urb unallocated,
something which could trigger a NULL pointer dereference on interrupt
events.

Fortunately the interrupt implementation is completely broken and has
never even been enabled...

Note that the zero-length-enable register write used to set the zle-flag
for all ports is moved to attach.

Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/usb/serial/mos7840.c | 48 +++++++++++++++++++++---------------
 1 file changed, 28 insertions(+), 20 deletions(-)

diff --git a/drivers/usb/serial/mos7840.c b/drivers/usb/serial/mos7840.c
index ab4bf8d6d7df0..e105ff0eb92e5 100644
--- a/drivers/usb/serial/mos7840.c
+++ b/drivers/usb/serial/mos7840.c
@@ -2090,6 +2090,23 @@ static int mos7840_calc_num_ports(struct usb_serial *serial,
 	return num_ports;
 }
 
+static int mos7840_attach(struct usb_serial *serial)
+{
+	struct device *dev = &serial->interface->dev;
+	int status;
+	u16 val;
+
+	/* Zero Length flag enable */
+	val = 0x0f;
+	status = mos7840_set_reg_sync(serial->port[0], ZLP_REG5, val);
+	if (status < 0)
+		dev_dbg(dev, "Writing ZLP_REG5 failed status-0x%x\n", status);
+	else
+		dev_dbg(dev, "ZLP_REG5 Writing success status%d\n", status);
+
+	return status;
+}
+
 static int mos7840_port_probe(struct usb_serial_port *port)
 {
 	struct usb_serial *serial = port->serial;
@@ -2147,7 +2164,7 @@ static int mos7840_port_probe(struct usb_serial_port *port)
 			mos7840_port->ControlRegOffset, &Data);
 	if (status < 0) {
 		dev_dbg(&port->dev, "Reading ControlReg failed status-0x%x\n", status);
-		goto out;
+		goto error;
 	} else
 		dev_dbg(&port->dev, "ControlReg Reading success val is %x, status%d\n", Data, status);
 	Data |= 0x08;	/* setting driver done bit */
@@ -2159,7 +2176,7 @@ static int mos7840_port_probe(struct usb_serial_port *port)
 			mos7840_port->ControlRegOffset, Data);
 	if (status < 0) {
 		dev_dbg(&port->dev, "Writing ControlReg failed(rx_disable) status-0x%x\n", status);
-		goto out;
+		goto error;
 	} else
 		dev_dbg(&port->dev, "ControlReg Writing success(rx_disable) status%d\n", status);
 
@@ -2170,7 +2187,7 @@ static int mos7840_port_probe(struct usb_serial_port *port)
 			(__u16) (mos7840_port->DcrRegOffset + 0), Data);
 	if (status < 0) {
 		dev_dbg(&port->dev, "Writing DCR0 failed status-0x%x\n", status);
-		goto out;
+		goto error;
 	} else
 		dev_dbg(&port->dev, "DCR0 Writing success status%d\n", status);
 
@@ -2179,7 +2196,7 @@ static int mos7840_port_probe(struct usb_serial_port *port)
 			(__u16) (mos7840_port->DcrRegOffset + 1), Data);
 	if (status < 0) {
 		dev_dbg(&port->dev, "Writing DCR1 failed status-0x%x\n", status);
-		goto out;
+		goto error;
 	} else
 		dev_dbg(&port->dev, "DCR1 Writing success status%d\n", status);
 
@@ -2188,7 +2205,7 @@ static int mos7840_port_probe(struct usb_serial_port *port)
 			(__u16) (mos7840_port->DcrRegOffset + 2), Data);
 	if (status < 0) {
 		dev_dbg(&port->dev, "Writing DCR2 failed status-0x%x\n", status);
-		goto out;
+		goto error;
 	} else
 		dev_dbg(&port->dev, "DCR2 Writing success status%d\n", status);
 
@@ -2197,7 +2214,7 @@ static int mos7840_port_probe(struct usb_serial_port *port)
 	status = mos7840_set_reg_sync(port, CLK_START_VALUE_REGISTER, Data);
 	if (status < 0) {
 		dev_dbg(&port->dev, "Writing CLK_START_VALUE_REGISTER failed status-0x%x\n", status);
-		goto out;
+		goto error;
 	} else
 		dev_dbg(&port->dev, "CLK_START_VALUE_REGISTER Writing success status%d\n", status);
 
@@ -2214,7 +2231,7 @@ static int mos7840_port_probe(struct usb_serial_port *port)
 	status = mos7840_set_uart_reg(port, SCRATCH_PAD_REGISTER, Data);
 	if (status < 0) {
 		dev_dbg(&port->dev, "Writing SCRATCH_PAD_REGISTER failed status-0x%x\n", status);
-		goto out;
+		goto error;
 	} else
 		dev_dbg(&port->dev, "SCRATCH_PAD_REGISTER Writing success status%d\n", status);
 
@@ -2228,7 +2245,7 @@ static int mos7840_port_probe(struct usb_serial_port *port)
 				(__u16)(ZLP_REG1 + ((__u16) mos7840_port->port_num)));
 		if (status < 0) {
 			dev_dbg(&port->dev, "Writing ZLP_REG%d failed status-0x%x\n", pnum + 2, status);
-			goto out;
+			goto error;
 		} else
 			dev_dbg(&port->dev, "ZLP_REG%d Writing success status%d\n", pnum + 2, status);
 	} else {
@@ -2240,7 +2257,7 @@ static int mos7840_port_probe(struct usb_serial_port *port)
 				(__u16)(ZLP_REG1 + ((__u16) mos7840_port->port_num) - 0x1));
 		if (status < 0) {
 			dev_dbg(&port->dev, "Writing ZLP_REG%d failed status-0x%x\n", pnum + 1, status);
-			goto out;
+			goto error;
 		} else
 			dev_dbg(&port->dev, "ZLP_REG%d Writing success status%d\n", pnum + 1, status);
 
@@ -2280,17 +2297,7 @@ static int mos7840_port_probe(struct usb_serial_port *port)
 		/* Turn off LED */
 		mos7840_set_led_sync(port, MODEM_CONTROL_REGISTER, 0x0300);
 	}
-out:
-	if (pnum == serial->num_ports - 1) {
-		/* Zero Length flag enable */
-		Data = 0x0f;
-		status = mos7840_set_reg_sync(serial->port[0], ZLP_REG5, Data);
-		if (status < 0) {
-			dev_dbg(&port->dev, "Writing ZLP_REG5 failed status-0x%x\n", status);
-			goto error;
-		} else
-			dev_dbg(&port->dev, "ZLP_REG5 Writing success status%d\n", status);
-	}
+
 	return 0;
 error:
 	kfree(mos7840_port->led_dr);
@@ -2346,6 +2353,7 @@ static struct usb_serial_driver moschip7840_4port_device = {
 	.unthrottle = mos7840_unthrottle,
 	.calc_num_ports = mos7840_calc_num_ports,
 	.probe = mos7840_probe,
+	.attach = mos7840_attach,
 	.ioctl = mos7840_ioctl,
 	.get_serial = mos7840_get_serial_info,
 	.set_termios = mos7840_set_termios,
-- 
2.25.1