From: youling257 <youling257@gmail.com>
To: mathias.nyman@linux.intel.com
Cc: gregkh@linuxfoundation.org, linux-usb@vger.kernel.org,
pkondeti@codeaurora.org, stable@vger.kernel.org
Subject: Re: [PATCH 4/5] xhci: Fix command ring pointer corruption while aborting a command
Date: Fri, 22 Oct 2021 18:59:13 +0800 [thread overview]
Message-ID: <20211022105913.7671-1-youling257@gmail.com> (raw)
In-Reply-To: <20211008092547.3996295-5-mathias.nyman@linux.intel.com>
This patch cause suspend to disk resume usb not work, xhci_hcd 0000:00:14.0: Abort failed to stop command ring: -110.
[ 189.292054] PM: hibernation: hibernation entry
[ 189.295273] Filesystems sync: 0.000 seconds
[ 189.295281] Freezing user space processes ... (elapsed 0.003 seconds) done.
[ 189.298514] OOM killer disabled.
[ 189.298590] PM: hibernation: Marking nosave pages: [mem 0x00000000-0x00000fff]
[ 189.298594] PM: hibernation: Marking nosave pages: [mem 0x00058000-0x00058fff]
[ 189.298596] PM: hibernation: Marking nosave pages: [mem 0x0009f000-0x000fffff]
[ 189.298600] PM: hibernation: Marking nosave pages: [mem 0x00500000-0x005fffff]
[ 189.298607] PM: hibernation: Marking nosave pages: [mem 0x850d7000-0x850d8fff]
[ 189.298609] PM: hibernation: Marking nosave pages: [mem 0x8805d000-0x8809bfff]
[ 189.298612] PM: hibernation: Marking nosave pages: [mem 0x8ac24000-0x8ac24fff]
[ 189.298614] PM: hibernation: Marking nosave pages: [mem 0x8bea8000-0x8caeefff]
[ 189.298689] PM: hibernation: Marking nosave pages: [mem 0x8cb9a000-0x8d3fefff]
[ 189.298741] PM: hibernation: Marking nosave pages: [mem 0x8d400000-0xffffffff]
[ 189.300918] PM: hibernation: Basic memory bitmaps created
[ 189.301088] PM: hibernation: Preallocating image memory
[ 189.812115] PM: hibernation: Allocated 779311 pages for snapshot
[ 189.812118] PM: hibernation: Allocated 3117244 kbytes in 0.51 seconds (6112.24 MB/s)
[ 189.812121] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 189.813884] printk: Suspending console(s) (use no_console_suspend to debug)
[ 189.814016] wlan0: deauthenticating from b4:a8:98:22:f9:ac by local choice (Reason: 3=DEAUTH_LEAVING)
[ 189.814310] rtc_cmos 00:05: suspend, ctrl 02
[ 189.844670] r8169 0000:01:00.0 eth0: Link is Down
[ 190.081522] ACPI: PM: Preparing to enter system sleep state S4
[ 190.083051] ACPI: PM: Saving platform NVS memory
[ 190.087556] Disabling non-boot CPUs ...
[ 190.089802] smpboot: CPU 1 is now offline
[ 190.092841] smpboot: CPU 2 is now offline
[ 190.095235] smpboot: CPU 3 is now offline
[ 190.098592] smpboot: CPU 4 is now offline
[ 190.100660] smpboot: CPU 5 is now offline
[ 190.102967] smpboot: CPU 6 is now offline
[ 190.105047] smpboot: CPU 7 is now offline
[ 190.106828] PM: hibernation: Creating image:
[ 190.211897] PM: hibernation: Need to copy 775681 pages
[ 190.211898] PM: hibernation: Normal pages needed: 775681 + 1024, available pages: 1300224
[ 190.107012] ACPI: PM: Restoring platform NVS memory
[ 190.108184] Enabling non-boot CPUs ...
[ 190.108225] x86: Booting SMP configuration:
[ 190.108225] smpboot: Booting Node 0 Processor 1 APIC 0x2
[ 190.109416] CPU1 is up
[ 190.109440] smpboot: Booting Node 0 Processor 2 APIC 0x4
[ 190.110088] CPU2 is up
[ 190.110111] smpboot: Booting Node 0 Processor 3 APIC 0x6
[ 190.110775] CPU3 is up
[ 190.110799] smpboot: Booting Node 0 Processor 4 APIC 0x1
[ 190.111532] CPU4 is up
[ 190.111558] smpboot: Booting Node 0 Processor 5 APIC 0x3
[ 190.112280] CPU5 is up
[ 190.112303] smpboot: Booting Node 0 Processor 6 APIC 0x5
[ 190.113056] CPU6 is up
[ 190.113084] smpboot: Booting Node 0 Processor 7 APIC 0x7
[ 190.113886] CPU7 is up
[ 190.116276] ACPI: PM: Waking up from system sleep state S4
[ 190.187264] usb usb1: root hub lost power or was reset
[ 190.187296] usb usb2: root hub lost power or was reset
[ 190.188384] rtc_cmos 00:05: resume, ctrl 02
[ 190.189946] i915 0000:00:02.0: [drm] [ENCODER:94:DDI B/PHY B] is disabled/in DSI mode with an ungated DDI clock, gate it
[ 190.195185] nvme nvme0: 8/0/0 default/read/poll queues
[ 190.354168] r8169 0000:01:00.0 eth0: Link is Down
[ 190.526336] ata3: SATA link down (SStatus 4 SControl 300)
[ 190.526389] ata4: SATA link down (SStatus 4 SControl 300)
[ 191.214037] snd_hda_intel 0000:00:1f.3: azx_get_response timeout, switching to polling mode: last cmd=0x206f0015
[ 191.214047] snd_hda_intel 0000:00:1f.3: spurious response 0x0:0x2, last cmd=0x206f0015
[ 191.214054] snd_hda_intel 0000:00:1f.3: spurious response 0x0:0x2, last cmd=0x206f0015
[ 191.214058] snd_hda_intel 0000:00:1f.3: spurious response 0x0:0x2, last cmd=0x206f0015
[ 191.214061] snd_hda_intel 0000:00:1f.3: spurious response 0x0:0x2, last cmd=0x206f0015
[ 191.214064] snd_hda_intel 0000:00:1f.3: spurious response 0x0:0x2, last cmd=0x206f0015
[ 191.214067] snd_hda_intel 0000:00:1f.3: spurious response 0x0:0x2, last cmd=0x206f0015
[ 191.214070] snd_hda_intel 0000:00:1f.3: spurious response 0x200:0x2, last cmd=0x206f0015
[ 191.214073] snd_hda_intel 0000:00:1f.3: spurious response 0x0:0x2, last cmd=0x206f0015
[ 191.214076] snd_hda_intel 0000:00:1f.3: spurious response 0x0:0x2, last cmd=0x206f0015
[ 191.214079] snd_hda_intel 0000:00:1f.3: spurious response 0x0:0x2, last cmd=0x206f0015
[ 192.216095] snd_hda_intel 0000:00:1f.3: No response from codec, disabling MSI: last cmd=0x20670100
[ 193.218095] snd_hda_intel 0000:00:1f.3: azx_get_response timeout, switching to single_cmd mode: last cmd=0x20670100
[ 193.547924] r8169 0000:01:00.0 eth0: Link is Up - 1Gbps/Full - flow control off
[ 200.640141] xhci_hcd 0000:00:14.0: Abort failed to stop command ring: -110
[ 200.640148] xhci_hcd 0000:00:14.0: xHCI host controller not responding, assume dead
[ 200.640151] xhci_hcd 0000:00:14.0: HC died; cleaning up
[ 200.640165] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
[ 201.056143] usb 2-1: device not accepting address 2, error -22
[ 201.058193] PM: hibernation: Basic memory bitmaps freed
[ 201.058197] OOM killer enabled.
[ 201.058197] Restarting tasks ...
[ 201.058212] usb 2-1: USB disconnect, device number 2
next prev parent reply other threads:[~2021-10-22 10:59 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-10-08 9:25 [PATCH 0/5] xhci fixes for usb-linus Mathias Nyman
2021-10-08 9:25 ` [PATCH 1/5] xhci: guard accesses to ep_state in xhci_endpoint_reset() Mathias Nyman
2021-10-08 9:25 ` [PATCH 2/5] xhci: add quirk for host controllers that don't update endpoint DCS Mathias Nyman
2021-10-08 9:25 ` [PATCH 3/5] USB: xhci: dbc: fix tty registration race Mathias Nyman
2021-10-08 9:25 ` [PATCH 4/5] xhci: Fix command ring pointer corruption while aborting a command Mathias Nyman
2021-10-22 10:59 ` youling257 [this message]
2021-10-22 11:00 ` youling 257
2021-10-25 11:21 ` Mathias Nyman
2021-10-25 15:01 ` youling 257
2021-10-25 15:21 ` Mathias Nyman
2021-10-26 10:49 ` Pavan Kondeti
2021-10-27 13:59 ` Mathias Nyman
2021-10-28 8:03 ` Pavan Kondeti
2021-10-29 12:48 ` Mathias Nyman
2021-10-29 12:51 ` [RFT PATCH] xhci: Fix commad ring abort, write all 64 bits to CRCR register Mathias Nyman
2021-10-29 15:35 ` youling 257
2021-11-01 8:37 ` Mathias Nyman
2021-11-01 3:31 ` Pavan Kondeti
2021-11-01 8:36 ` Mathias Nyman
2021-10-08 9:25 ` [PATCH 5/5] xhci: Enable trust tx length quirk for Fresco FL11 USB controller Mathias Nyman
2021-10-08 16:13 ` [PATCH 0/5] xhci fixes for usb-linus Greg KH
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20211022105913.7671-1-youling257@gmail.com \
--to=youling257@gmail.com \
--cc=gregkh@linuxfoundation.org \
--cc=linux-usb@vger.kernel.org \
--cc=mathias.nyman@linux.intel.com \
--cc=pkondeti@codeaurora.org \
--cc=stable@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox