* [PATCH AUTOSEL 4.14 3/9] xhci: Don't require a valid get_quirks() function pointer during xhci setup
[not found] <20230724013554.2334965-1-sashal@kernel.org>
@ 2023-07-24 1:35 ` Sasha Levin
2023-07-24 4:08 ` Greg Kroah-Hartman
2023-07-24 1:35 ` [PATCH AUTOSEL 4.14 4/9] usb: cdns2: Device side header file for CDNS2 driver Sasha Levin
1 sibling, 1 reply; 3+ messages in thread
From: Sasha Levin @ 2023-07-24 1:35 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Mathias Nyman, Greg Kroah-Hartman, Sasha Levin, mathias.nyman,
linux-usb
From: Mathias Nyman <mathias.nyman@linux.intel.com>
[ Upstream commit 9b907c91aa94522ae14bf155ce7b9ccb10a0903c ]
Not all platforms drivers need to set up custom quirks during the xhci
generic setup. Allow them to pass NULL as the function pointer when
calling xhci_gen_setup()
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Message-ID: <20230602144009.1225632-4-mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/usb/host/xhci.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index 0f2b67f38d2ea..3feee0419fdd9 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -4975,7 +4975,8 @@ int xhci_gen_setup(struct usb_hcd *hcd, xhci_get_quirks_t get_quirks)
xhci->quirks |= quirks;
- get_quirks(dev, xhci);
+ if (get_quirks)
+ get_quirks(dev, xhci);
/* In xhci controllers which follow xhci 1.0 spec gives a spurious
* success event after a short transfer. This quirk will ignore such
--
2.39.2
^ permalink raw reply related [flat|nested] 3+ messages in thread* [PATCH AUTOSEL 4.14 4/9] usb: cdns2: Device side header file for CDNS2 driver
[not found] <20230724013554.2334965-1-sashal@kernel.org>
2023-07-24 1:35 ` [PATCH AUTOSEL 4.14 3/9] xhci: Don't require a valid get_quirks() function pointer during xhci setup Sasha Levin
@ 2023-07-24 1:35 ` Sasha Levin
1 sibling, 0 replies; 3+ messages in thread
From: Sasha Levin @ 2023-07-24 1:35 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Pawel Laszczak, Greg Kroah-Hartman, Sasha Levin, balbi, linux-usb
From: Pawel Laszczak <pawell@cadence.com>
[ Upstream commit 0ca2026eea104adc1d0d356bca35915a1ab6e3e9 ]
Patch defines macros, registers and structures used by
Device side driver.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Message-ID: <20230602102644.77470-2-pawell@cadence.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/usb/gadget/udc/cdns2/cdns2-gadget.h | 707 ++++++++++++++++++++
1 file changed, 707 insertions(+)
create mode 100644 drivers/usb/gadget/udc/cdns2/cdns2-gadget.h
diff --git a/drivers/usb/gadget/udc/cdns2/cdns2-gadget.h b/drivers/usb/gadget/udc/cdns2/cdns2-gadget.h
new file mode 100644
index 0000000000000..71e2f62d653a5
--- /dev/null
+++ b/drivers/usb/gadget/udc/cdns2/cdns2-gadget.h
@@ -0,0 +1,707 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * USBHS-DEV device controller driver header file
+ *
+ * Copyright (C) 2023 Cadence.
+ *
+ * Author: Pawel Laszczak <pawell@cadence.com>
+ */
+
+#ifndef __LINUX_CDNS2_GADGET
+#define __LINUX_CDNS2_GADGET
+
+#include <linux/usb/gadget.h>
+#include <linux/dma-direction.h>
+
+/*
+ * USBHS register interface.
+ * This corresponds to the USBHS Device Controller Interface.
+ */
+
+/**
+ * struct cdns2_ep0_regs - endpoint 0 related registers.
+ * @rxbc: receive (OUT) 0 endpoint byte count register.
+ * @txbc: transmit (IN) 0 endpoint byte count register.
+ * @cs: 0 endpoint control and status register.
+ * @reserved1: reserved.
+ * @fifo: 0 endpoint fifo register.
+ * @reserved2: reserved.
+ * @setupdat: SETUP data register.
+ * @reserved4: reserved.
+ * @maxpack: 0 endpoint max packet size.
+ */
+struct cdns2_ep0_regs {
+ __u8 rxbc;
+ __u8 txbc;
+ __u8 cs;
+ __u8 reserved1[4];
+ __u8 fifo;
+ __le32 reserved2[94];
+ __u8 setupdat[8];
+ __u8 reserved4[88];
+ __u8 maxpack;
+} __packed __aligned(4);
+
+/* EP0CS - bitmasks. */
+/* Endpoint 0 stall bit for status stage. */
+#define EP0CS_STALL BIT(0)
+/* HSNAK bit. */
+#define EP0CS_HSNAK BIT(1)
+/* IN 0 endpoint busy bit. */
+#define EP0CS_TXBSY_MSK BIT(2)
+/* OUT 0 endpoint busy bit. */
+#define EP0CS_RXBSY_MSK BIT(3)
+/* Send STALL in the data stage phase. */
+#define EP0CS_DSTALL BIT(4)
+/* SETUP buffer content was changed. */
+#define EP0CS_CHGSET BIT(7)
+
+/* EP0FIFO - bitmasks. */
+/* Direction. */
+#define EP0_FIFO_IO_TX BIT(4)
+/* FIFO auto bit. */
+#define EP0_FIFO_AUTO BIT(5)
+/* FIFO commit bit. */
+#define EP0_FIFO_COMMIT BIT(6)
+/* FIFO access bit. */
+#define EP0_FIFO_ACCES BIT(7)
+
+/**
+ * struct cdns2_epx_base - base endpoint registers.
+ * @rxbc: OUT endpoint byte count register.
+ * @rxcon: OUT endpoint control register.
+ * @rxcs: OUT endpoint control and status register.
+ * @txbc: IN endpoint byte count register.
+ * @txcon: IN endpoint control register.
+ * @txcs: IN endpoint control and status register.
+ */
+struct cdns2_epx_base {
+ __le16 rxbc;
+ __u8 rxcon;
+ __u8 rxcs;
+ __le16 txbc;
+ __u8 txcon;
+ __u8 txcs;
+} __packed __aligned(4);
+
+/* rxcon/txcon - endpoint control register bitmasks. */
+/* Endpoint buffering: 0 - single buffering ... 3 - quad buffering. */
+#define EPX_CON_BUF GENMASK(1, 0)
+/* Endpoint type. */
+#define EPX_CON_TYPE GENMASK(3, 2)
+/* Endpoint type: isochronous. */
+#define EPX_CON_TYPE_ISOC 0x4
+/* Endpoint type: bulk. */
+#define EPX_CON_TYPE_BULK 0x8
+/* Endpoint type: interrupt. */
+#define EPX_CON_TYPE_INT 0xC
+/* Number of packets per microframe. */
+#define EPX_CON_ISOD GENMASK(5, 4)
+#define EPX_CON_ISOD_SHIFT 0x4
+/* Endpoint stall bit. */
+#define EPX_CON_STALL BIT(6)
+/* Endpoint enable bit.*/
+#define EPX_CON_VAL BIT(7)
+
+/* rxcs/txcs - endpoint control and status bitmasks. */
+/* Data sequence error for the ISO endpoint. */
+#define EPX_CS_ERR(p) ((p) & BIT(0))
+
+/**
+ * struct cdns2_epx_regs - endpoint 1..15 related registers.
+ * @reserved: reserved.
+ * @ep: none control endpoints array.
+ * @reserved2: reserved.
+ * @endprst: endpoint reset register.
+ * @reserved3: reserved.
+ * @isoautoarm: ISO auto-arm register.
+ * @reserved4: reserved.
+ * @isodctrl: ISO control register.
+ * @reserved5: reserved.
+ * @isoautodump: ISO auto dump enable register.
+ * @reserved6: reserved.
+ * @rxmaxpack: receive (OUT) Max packet size register.
+ * @reserved7: reserved.
+ * @rxstaddr: receive (OUT) start address endpoint buffer register.
+ * @reserved8: reserved.
+ * @txstaddr: transmit (IN) start address endpoint buffer register.
+ * @reserved9: reserved.
+ * @txmaxpack: transmit (IN) Max packet size register.
+ */
+struct cdns2_epx_regs {
+ __le32 reserved[2];
+ struct cdns2_epx_base ep[15];
+ __u8 reserved2[290];
+ __u8 endprst;
+ __u8 reserved3[41];
+ __le16 isoautoarm;
+ __u8 reserved4[10];
+ __le16 isodctrl;
+ __le16 reserved5;
+ __le16 isoautodump;
+ __le32 reserved6;
+ __le16 rxmaxpack[15];
+ __le32 reserved7[65];
+ __le32 rxstaddr[15];
+ __u8 reserved8[4];
+ __le32 txstaddr[15];
+ __u8 reserved9[98];
+ __le16 txmaxpack[15];
+} __packed __aligned(4);
+
+/* ENDPRST - bitmasks. */
+/* Endpoint number. */
+#define ENDPRST_EP GENMASK(3, 0)
+/* IN direction bit. */
+#define ENDPRST_IO_TX BIT(4)
+/* Toggle reset bit. */
+#define ENDPRST_TOGRST BIT(5)
+/* FIFO reset bit. */
+#define ENDPRST_FIFORST BIT(6)
+/* Toggle status and reset bit. */
+#define ENDPRST_TOGSETQ BIT(7)
+
+/**
+ * struct cdns2_interrupt_regs - USB interrupt related registers.
+ * @reserved: reserved.
+ * @usbirq: USB interrupt request register.
+ * @extirq: external interrupt request register.
+ * @rxpngirq: external interrupt request register.
+ * @reserved1: reserved.
+ * @usbien: USB interrupt enable register.
+ * @extien: external interrupt enable register.
+ * @reserved2: reserved.
+ * @usbivect: USB interrupt vector register.
+ */
+struct cdns2_interrupt_regs {
+ __u8 reserved[396];
+ __u8 usbirq;
+ __u8 extirq;
+ __le16 rxpngirq;
+ __le16 reserved1[4];
+ __u8 usbien;
+ __u8 extien;
+ __le16 reserved2[3];
+ __u8 usbivect;
+} __packed __aligned(4);
+
+/* EXTIRQ and EXTIEN - bitmasks. */
+/* VBUS fault fall interrupt. */
+#define EXTIRQ_VBUSFAULT_FALL BIT(0)
+/* VBUS fault fall interrupt. */
+#define EXTIRQ_VBUSFAULT_RISE BIT(1)
+/* Wake up interrupt bit. */
+#define EXTIRQ_WAKEUP BIT(7)
+
+/* USBIEN and USBIRQ - bitmasks. */
+/* SETUP data valid interrupt bit.*/
+#define USBIRQ_SUDAV BIT(0)
+/* Start-of-frame interrupt bit. */
+#define USBIRQ_SOF BIT(1)
+/* SETUP token interrupt bit. */
+#define USBIRQ_SUTOK BIT(2)
+/* USB suspend interrupt bit. */
+#define USBIRQ_SUSPEND BIT(3)
+/* USB reset interrupt bit. */
+#define USBIRQ_URESET BIT(4)
+/* USB high-speed mode interrupt bit. */
+#define USBIRQ_HSPEED BIT(5)
+/* Link Power Management interrupt bit. */
+#define USBIRQ_LPM BIT(7)
+
+#define USB_IEN_INIT (USBIRQ_SUDAV | USBIRQ_SUSPEND | USBIRQ_URESET \
+ | USBIRQ_HSPEED | USBIRQ_LPM)
+/**
+ * struct cdns2_usb_regs - USB controller registers.
+ * @reserved: reserved.
+ * @lpmctrl: LPM control register.
+ * @lpmclock: LPM clock register.
+ * @reserved2: reserved.
+ * @endprst: endpoint reset register.
+ * @usbcs: USB control and status register.
+ * @frmnr: USB frame counter register.
+ * @fnaddr: function Address register.
+ * @clkgate: clock gate register.
+ * @fifoctrl: FIFO control register.
+ * @speedctrl: speed Control register.
+ * @sleep_clkgate: sleep Clock Gate register.
+ * @reserved3: reserved.
+ * @cpuctrl: microprocessor control register.
+ */
+struct cdns2_usb_regs {
+ __u8 reserved[4];
+ __u16 lpmctrl;
+ __u8 lpmclock;
+ __u8 reserved2[411];
+ __u8 endprst;
+ __u8 usbcs;
+ __le16 frmnr;
+ __u8 fnaddr;
+ __u8 clkgate;
+ __u8 fifoctrl;
+ __u8 speedctrl;
+ __u8 sleep_clkgate;
+ __u8 reserved3[533];
+ __u8 cpuctrl;
+} __packed __aligned(4);
+
+/* LPMCTRL - bitmasks. */
+/* BESL (Best Effort Service Latency). */
+#define LPMCTRLLL_HIRD GENMASK(7, 4)
+/* Last received Remote Wakeup field from LPM Extended Token packet. */
+#define LPMCTRLLH_BREMOTEWAKEUP BIT(8)
+/* Reflects value of the lpmnyet bit located in the usbcs[1] register. */
+#define LPMCTRLLH_LPMNYET BIT(16)
+
+/* LPMCLOCK - bitmasks. */
+/*
+ * If bit is 1 the controller automatically turns off clock
+ * (utmisleepm goes to low), else the microprocessor should use
+ * sleep clock gate register to turn off clock.
+ */
+#define LPMCLOCK_SLEEP_ENTRY BIT(7)
+
+/* USBCS - bitmasks. */
+/* Send NYET handshake for the LPM transaction. */
+#define USBCS_LPMNYET BIT(2)
+/* Remote wake-up bit. */
+#define USBCS_SIGRSUME BIT(5)
+/* Software disconnect bit. */
+#define USBCS_DISCON BIT(6)
+/* Indicates that a wakeup pin resumed the controller. */
+#define USBCS_WAKESRC BIT(7)
+
+/* FIFOCTRL - bitmasks. */
+/* Endpoint number. */
+#define FIFOCTRL_EP GENMASK(3, 0)
+/* Direction bit. */
+#define FIFOCTRL_IO_TX BIT(4)
+/* FIFO auto bit. */
+#define FIFOCTRL_FIFOAUTO BIT(5)
+/* FIFO commit bit. */
+#define FIFOCTRL_FIFOCMIT BIT(6)
+/* FIFO access bit. */
+#define FIFOCTRL_FIFOACC BIT(7)
+
+/* SPEEDCTRL - bitmasks. */
+/* Device works in Full Speed. */
+#define SPEEDCTRL_FS BIT(1)
+/* Device works in High Speed. */
+#define SPEEDCTRL_HS BIT(2)
+/* Force FS mode. */
+#define SPEEDCTRL_HSDISABLE BIT(7)
+
+/* CPUCTRL- bitmasks. */
+/* Controller reset bit. */
+#define CPUCTRL_SW_RST BIT(1)
+
+/**
+ * struct cdns2_adma_regs - ADMA controller registers.
+ * @conf: DMA global configuration register.
+ * @sts: DMA global Status register.
+ * @reserved1: reserved.
+ * @ep_sel: DMA endpoint select register.
+ * @ep_traddr: DMA endpoint transfer ring address register.
+ * @ep_cfg: DMA endpoint configuration register.
+ * @ep_cmd: DMA endpoint command register.
+ * @ep_sts: DMA endpoint status register.
+ * @reserved2: reserved.
+ * @ep_sts_en: DMA endpoint status enable register.
+ * @drbl: DMA doorbell register.
+ * @ep_ien: DMA endpoint interrupt enable register.
+ * @ep_ists: DMA endpoint interrupt status register.
+ * @axim_ctrl: AXI Master Control register.
+ * @axim_id: AXI Master ID register.
+ * @reserved3: reserved.
+ * @axim_cap: AXI Master Wrapper Extended Capability.
+ * @reserved4: reserved.
+ * @axim_ctrl0: AXI Master Wrapper Extended Capability Control Register 0.
+ * @axim_ctrl1: AXI Master Wrapper Extended Capability Control Register 1.
+ */
+struct cdns2_adma_regs {
+ __le32 conf;
+ __le32 sts;
+ __le32 reserved1[5];
+ __le32 ep_sel;
+ __le32 ep_traddr;
+ __le32 ep_cfg;
+ __le32 ep_cmd;
+ __le32 ep_sts;
+ __le32 reserved2;
+ __le32 ep_sts_en;
+ __le32 drbl;
+ __le32 ep_ien;
+ __le32 ep_ists;
+ __le32 axim_ctrl;
+ __le32 axim_id;
+ __le32 reserved3;
+ __le32 axim_cap;
+ __le32 reserved4;
+ __le32 axim_ctrl0;
+ __le32 axim_ctrl1;
+};
+
+#define CDNS2_ADMA_REGS_OFFSET 0x400
+
+/* DMA_CONF - bitmasks. */
+/* Reset USB device configuration. */
+#define DMA_CONF_CFGRST BIT(0)
+/* Singular DMA transfer mode.*/
+#define DMA_CONF_DSING BIT(8)
+/* Multiple DMA transfers mode.*/
+#define DMA_CONF_DMULT BIT(9)
+
+/* DMA_EP_CFG - bitmasks. */
+/* Endpoint enable. */
+#define DMA_EP_CFG_ENABLE BIT(0)
+
+/* DMA_EP_CMD - bitmasks. */
+/* Endpoint reset. */
+#define DMA_EP_CMD_EPRST BIT(0)
+/* Transfer descriptor ready. */
+#define DMA_EP_CMD_DRDY BIT(6)
+/* Data flush. */
+#define DMA_EP_CMD_DFLUSH BIT(7)
+
+/* DMA_EP_STS - bitmasks. */
+/* Interrupt On Complete. */
+#define DMA_EP_STS_IOC BIT(2)
+/* Interrupt on Short Packet. */
+#define DMA_EP_STS_ISP BIT(3)
+/* Transfer descriptor missing. */
+#define DMA_EP_STS_DESCMIS BIT(4)
+/* TRB error. */
+#define DMA_EP_STS_TRBERR BIT(7)
+/* DMA busy bit. */
+#define DMA_EP_STS_DBUSY BIT(9)
+/* Current Cycle Status. */
+#define DMA_EP_STS_CCS(p) ((p) & BIT(11))
+/* OUT size mismatch. */
+#define DMA_EP_STS_OUTSMM BIT(14)
+/* ISO transmission error. */
+#define DMA_EP_STS_ISOERR BIT(15)
+
+/* DMA_EP_STS_EN - bitmasks. */
+/* OUT transfer missing descriptor enable. */
+#define DMA_EP_STS_EN_DESCMISEN BIT(4)
+/* TRB enable. */
+#define DMA_EP_STS_EN_TRBERREN BIT(7)
+/* OUT size mismatch enable. */
+#define DMA_EP_STS_EN_OUTSMMEN BIT(14)
+/* ISO transmission error enable. */
+#define DMA_EP_STS_EN_ISOERREN BIT(15)
+
+/* DMA_EP_IEN - bitmasks. */
+#define DMA_EP_IEN(index) (1 << (index))
+#define DMA_EP_IEN_EP_OUT0 BIT(0)
+#define DMA_EP_IEN_EP_IN0 BIT(16)
+
+/* DMA_EP_ISTS - bitmasks. */
+#define DMA_EP_ISTS(index) (1 << (index))
+#define DMA_EP_ISTS_EP_OUT0 BIT(0)
+#define DMA_EP_ISTS_EP_IN0 BIT(16)
+
+#define gadget_to_cdns2_device(g) (container_of(g, struct cdns2_device, gadget))
+#define ep_to_cdns2_ep(ep) (container_of(ep, struct cdns2_endpoint, endpoint))
+
+/*-------------------------------------------------------------------------*/
+#define TRBS_PER_SEGMENT 600
+#define ISO_MAX_INTERVAL 8
+#define MAX_TRB_LENGTH BIT(16)
+#define MAX_ISO_SIZE 3076
+/*
+ * To improve performance the TRB buffer pointers can't cross
+ * 4KB boundaries.
+ */
+#define TRB_MAX_ISO_BUFF_SHIFT 12
+#define TRB_MAX_ISO_BUFF_SIZE BIT(TRB_MAX_ISO_BUFF_SHIFT)
+/* How much data is left before the 4KB boundary? */
+#define TRB_BUFF_LEN_UP_TO_BOUNDARY(addr) (TRB_MAX_ISO_BUFF_SIZE - \
+ ((addr) & (TRB_MAX_ISO_BUFF_SIZE - 1)))
+
+#if TRBS_PER_SEGMENT < 2
+#error "Incorrect TRBS_PER_SEGMENT. Minimal Transfer Ring size is 2."
+#endif
+
+/**
+ * struct cdns2_trb - represent Transfer Descriptor block.
+ * @buffer: pointer to buffer data.
+ * @length: length of data.
+ * @control: control flags.
+ *
+ * This structure describes transfer block handled by DMA module.
+ */
+struct cdns2_trb {
+ __le32 buffer;
+ __le32 length;
+ __le32 control;
+};
+
+#define TRB_SIZE (sizeof(struct cdns2_trb))
+/*
+ * These two extra TRBs are reserved for isochronous transfer
+ * to inject 0 length packet and extra LINK TRB to synchronize the ISO transfer.
+ */
+#define TRB_ISO_RESERVED 2
+#define TR_SEG_SIZE (TRB_SIZE * (TRBS_PER_SEGMENT + TRB_ISO_RESERVED))
+
+/* TRB bit mask. */
+#define TRB_TYPE_BITMASK GENMASK(15, 10)
+#define TRB_TYPE(p) ((p) << 10)
+#define TRB_FIELD_TO_TYPE(p) (((p) & TRB_TYPE_BITMASK) >> 10)
+
+/* TRB type IDs. */
+/* Used for Bulk, Interrupt, ISOC, and control data stage. */
+#define TRB_NORMAL 1
+/* TRB for linking ring segments. */
+#define TRB_LINK 6
+
+/* Cycle bit - indicates TRB ownership by driver or hw. */
+#define TRB_CYCLE BIT(0)
+/*
+ * When set to '1', the device will toggle its interpretation of the Cycle bit.
+ */
+#define TRB_TOGGLE BIT(1)
+/* Interrupt on short packet. */
+#define TRB_ISP BIT(2)
+/* Chain bit associate this TRB with next one TRB. */
+#define TRB_CHAIN BIT(4)
+/* Interrupt on completion. */
+#define TRB_IOC BIT(5)
+
+/* Transfer_len bitmasks. */
+#define TRB_LEN(p) ((p) & GENMASK(16, 0))
+#define TRB_BURST(p) (((p) << 24) & GENMASK(31, 24))
+#define TRB_FIELD_TO_BURST(p) (((p) & GENMASK(31, 24)) >> 24)
+
+/* Data buffer pointer bitmasks. */
+#define TRB_BUFFER(p) ((p) & GENMASK(31, 0))
+
+/*-------------------------------------------------------------------------*/
+/* Driver numeric constants. */
+
+/* Maximum address that can be assigned to device. */
+#define USB_DEVICE_MAX_ADDRESS 127
+
+/* One control and 15 IN and 15 OUT endpoints. */
+#define CDNS2_ENDPOINTS_NUM 31
+
+#define CDNS2_EP_ZLP_BUF_SIZE 512
+
+/*-------------------------------------------------------------------------*/
+/* Used structures. */
+
+struct cdns2_device;
+
+/**
+ * struct cdns2_ring - transfer ring representation.
+ * @trbs: pointer to transfer ring.
+ * @dma: dma address of transfer ring.
+ * @free_trbs: number of free TRBs in transfer ring.
+ * @pcs: producer cycle state.
+ * @ccs: consumer cycle state.
+ * @enqueue: enqueue index in transfer ring.
+ * @dequeue: dequeue index in transfer ring.
+ */
+struct cdns2_ring {
+ struct cdns2_trb *trbs;
+ dma_addr_t dma;
+ int free_trbs;
+ u8 pcs;
+ u8 ccs;
+ int enqueue;
+ int dequeue;
+};
+
+/**
+ * struct cdns2_endpoint - extended device side representation of USB endpoint.
+ * @endpoint: usb endpoint.
+ * @pending_list: list of requests queuing on transfer ring.
+ * @deferred_list: list of requests waiting for queuing on transfer ring.
+ * @pdev: device associated with endpoint.
+ * @name: a human readable name e.g. ep1out.
+ * @ring: transfer ring associated with endpoint.
+ * @ep_state: state of endpoint.
+ * @idx: index of endpoint in pdev->eps table.
+ * @dir: endpoint direction.
+ * @num: endpoint number (1 - 15).
+ * @type: set to bmAttributes & USB_ENDPOINT_XFERTYPE_MASK.
+ * @interval: interval between packets used for ISOC and Interrupt endpoint.
+ * @buffering: on-chip buffers assigned to endpoint.
+ * @trb_burst_size: number of burst used in TRB.
+ * @skip: Sometimes the controller cannot process isochronous endpoint ring
+ * quickly enough and it will miss some isoc tds on the ring and
+ * generate ISO transmition error.
+ * Driver sets skip flag when receive a ISO transmition error and
+ * process the missed TDs on the endpoint ring.
+ * @wa1_set: use WA1.
+ * @wa1_trb: TRB assigned to WA1.
+ * @wa1_trb_index: TRB index for WA1.
+ * @wa1_cycle_bit: correct cycle bit for WA1.
+ */
+struct cdns2_endpoint {
+ struct usb_ep endpoint;
+ struct list_head pending_list;
+ struct list_head deferred_list;
+
+ struct cdns2_device *pdev;
+ char name[20];
+
+ struct cdns2_ring ring;
+
+#define EP_ENABLED BIT(0)
+#define EP_STALLED BIT(1)
+#define EP_STALL_PENDING BIT(2)
+#define EP_WEDGE BIT(3)
+#define EP_CLAIMED BIT(4)
+#define EP_RING_FULL BIT(5)
+#define EP_DEFERRED_DRDY BIT(6)
+
+ u32 ep_state;
+
+ u8 idx;
+ u8 dir;
+ u8 num;
+ u8 type;
+ int interval;
+ u8 buffering;
+ u8 trb_burst_size;
+ bool skip;
+
+ unsigned int wa1_set:1;
+ struct cdns2_trb *wa1_trb;
+ unsigned int wa1_trb_index;
+ unsigned int wa1_cycle_bit:1;
+};
+
+/**
+ * struct cdns2_request - extended device side representation of usb_request
+ * object.
+ * @request: generic usb_request object describing single I/O request.
+ * @pep: extended representation of usb_ep object.
+ * @trb: the first TRB association with this request.
+ * @start_trb: number of the first TRB in transfer ring.
+ * @end_trb: number of the last TRB in transfer ring.
+ * @list: used for queuing request in lists.
+ * @finished_trb: number of trb has already finished per request.
+ * @num_of_trb: how many trbs are associated with request.
+ */
+struct cdns2_request {
+ struct usb_request request;
+ struct cdns2_endpoint *pep;
+ struct cdns2_trb *trb;
+ int start_trb;
+ int end_trb;
+ struct list_head list;
+ int finished_trb;
+ int num_of_trb;
+};
+
+#define to_cdns2_request(r) (container_of(r, struct cdns2_request, request))
+
+/* Stages used during enumeration process.*/
+#define CDNS2_SETUP_STAGE 0x0
+#define CDNS2_DATA_STAGE 0x1
+#define CDNS2_STATUS_STAGE 0x2
+
+/**
+ * struct cdns2_device - represent USB device.
+ * @dev: pointer to device structure associated whit this controller.
+ * @gadget: device side representation of the peripheral controller.
+ * @gadget_driver: pointer to the gadget driver.
+ * @lock: for synchronizing.
+ * @irq: interrupt line number.
+ * @regs: base address for registers
+ * @usb_regs: base address for common USB registers.
+ * @ep0_regs: base address for endpoint 0 related registers.
+ * @epx_regs: base address for all none control endpoint registers.
+ * @interrupt_regs: base address for interrupt handling related registers.
+ * @adma_regs: base address for ADMA registers.
+ * @eps_dma_pool: endpoint Transfer Ring pool.
+ * @setup: used while processing usb control requests.
+ * @ep0_preq: private request used while handling EP0.
+ * @ep0_stage: ep0 stage during enumeration process.
+ * @zlp_buf: zlp buffer.
+ * @dev_address: device address assigned by host.
+ * @eps: array of objects describing endpoints.
+ * @selected_ep: actually selected endpoint. It's used only to improve
+ * performance by limiting access to dma_ep_sel register.
+ * @is_selfpowered: device is self powered.
+ * @may_wakeup: allows device to remote wakeup the host.
+ * @status_completion_no_call: indicate that driver is waiting for status
+ * stage completion. It's used in deferred SET_CONFIGURATION request.
+ * @in_lpm: indicate the controller is in low power mode.
+ * @pending_status_wq: workqueue handling status stage for deferred requests.
+ * @pending_status_request: request for which status stage was deferred.
+ * @eps_supported: endpoints supported by controller in form:
+ * bit: 0 - ep0, 1 - epOut1, 2 - epIn1, 3 - epOut2 ...
+ * @burst_opt: array with the best burst size value for different TRB size.
+ * @onchip_tx_buf: size of transmit on-chip buffer in KB.
+ * @onchip_rx_buf: size of receive on-chip buffer in KB.
+ */
+struct cdns2_device {
+ struct device *dev;
+ struct usb_gadget gadget;
+ struct usb_gadget_driver *gadget_driver;
+
+ /* generic spin-lock for drivers */
+ spinlock_t lock;
+ int irq;
+ void __iomem *regs;
+ struct cdns2_usb_regs __iomem *usb_regs;
+ struct cdns2_ep0_regs __iomem *ep0_regs;
+ struct cdns2_epx_regs __iomem *epx_regs;
+ struct cdns2_interrupt_regs __iomem *interrupt_regs;
+ struct cdns2_adma_regs __iomem *adma_regs;
+ struct dma_pool *eps_dma_pool;
+ struct usb_ctrlrequest setup;
+ struct cdns2_request ep0_preq;
+ u8 ep0_stage;
+ void *zlp_buf;
+ u8 dev_address;
+ struct cdns2_endpoint eps[CDNS2_ENDPOINTS_NUM];
+ u32 selected_ep;
+ bool is_selfpowered;
+ bool may_wakeup;
+ bool status_completion_no_call;
+ bool in_lpm;
+ struct work_struct pending_status_wq;
+ struct usb_request *pending_status_request;
+ u32 eps_supported;
+ u8 burst_opt[MAX_ISO_SIZE + 1];
+
+ /*in KB */
+ u16 onchip_tx_buf;
+ u16 onchip_rx_buf;
+};
+
+#define CDNS2_IF_EP_EXIST(pdev, ep_num, dir) \
+ ((pdev)->eps_supported & \
+ (BIT(ep_num) << ((dir) ? 0 : 16)))
+
+dma_addr_t cdns2_trb_virt_to_dma(struct cdns2_endpoint *pep,
+ struct cdns2_trb *trb);
+void cdns2_pending_setup_status_handler(struct work_struct *work);
+void cdns2_select_ep(struct cdns2_device *pdev, u32 ep);
+struct cdns2_request *cdns2_next_preq(struct list_head *list);
+struct usb_request *cdns2_gadget_ep_alloc_request(struct usb_ep *ep,
+ gfp_t gfp_flags);
+void cdns2_gadget_ep_free_request(struct usb_ep *ep,
+ struct usb_request *request);
+int cdns2_gadget_ep_dequeue(struct usb_ep *ep, struct usb_request *request);
+void cdns2_gadget_giveback(struct cdns2_endpoint *pep,
+ struct cdns2_request *priv_req,
+ int status);
+void cdns2_init_ep0(struct cdns2_device *pdev, struct cdns2_endpoint *pep);
+void cdns2_ep0_config(struct cdns2_device *pdev);
+void cdns2_handle_ep0_interrupt(struct cdns2_device *pdev, int dir);
+void cdns2_handle_setup_packet(struct cdns2_device *pdev);
+int cdns2_gadget_resume(struct cdns2_device *pdev, bool hibernated);
+int cdns2_gadget_suspend(struct cdns2_device *pdev);
+void cdns2_gadget_remove(struct cdns2_device *pdev);
+int cdns2_gadget_init(struct cdns2_device *pdev);
+void set_reg_bit_8(void __iomem *ptr, u8 mask);
+int cdns2_halt_endpoint(struct cdns2_device *pdev, struct cdns2_endpoint *pep,
+ int value);
+
+#endif /* __LINUX_CDNS2_GADGET */
--
2.39.2
^ permalink raw reply related [flat|nested] 3+ messages in thread