Linux USB
 help / color / mirror / Atom feed
From: Xu Yang <xu.yang_2@nxp.com>
To: linux@roeck-us.net, heikki.krogerus@linux.intel.com
Cc: linux-usb@vger.kernel.org, gregkh@linuxfoundation.org, jun.li@nxp.com
Subject: [PATCH 1/2] usb: typec: tcpci: add check code for tcpci/regmap_read/write()
Date: Mon, 28 Aug 2023 17:30:34 +0800	[thread overview]
Message-ID: <20230828093035.1556639-1-xu.yang_2@nxp.com> (raw)

The return value from tcpci/regmap_read/write() must be checked to get
rid of the bad influence of other modules. This will add check code for
all of the rest read/write() callbacks and will show error when failed
to get ALERT register.

Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
---
 drivers/usb/typec/tcpm/tcpci.c | 36 +++++++++++++++++++++++++---------
 1 file changed, 27 insertions(+), 9 deletions(-)

diff --git a/drivers/usb/typec/tcpm/tcpci.c b/drivers/usb/typec/tcpm/tcpci.c
index 0ee3e6e29bb1..698d00b7fce9 100644
--- a/drivers/usb/typec/tcpm/tcpci.c
+++ b/drivers/usb/typec/tcpm/tcpci.c
@@ -657,21 +657,30 @@ irqreturn_t tcpci_irq(struct tcpci *tcpci)
 	int ret;
 	unsigned int raw;
 
-	tcpci_read16(tcpci, TCPC_ALERT, &status);
+	ret = tcpci_read16(tcpci, TCPC_ALERT, &status);
+	if (ret < 0) {
+		dev_err(tcpci->dev, "ALERT read failed\n");
+		return ret;
+	}
 
 	/*
 	 * Clear alert status for everything except RX_STATUS, which shouldn't
 	 * be cleared until we have successfully retrieved message.
 	 */
-	if (status & ~TCPC_ALERT_RX_STATUS)
-		tcpci_write16(tcpci, TCPC_ALERT,
+	if (status & ~TCPC_ALERT_RX_STATUS) {
+		ret = tcpci_write16(tcpci, TCPC_ALERT,
 			      status & ~TCPC_ALERT_RX_STATUS);
+		if (ret < 0)
+			return ret;
+	}
 
 	if (status & TCPC_ALERT_CC_STATUS)
 		tcpm_cc_change(tcpci->port);
 
 	if (status & TCPC_ALERT_POWER_STATUS) {
-		regmap_read(tcpci->regmap, TCPC_POWER_STATUS_MASK, &raw);
+		ret = regmap_read(tcpci->regmap, TCPC_POWER_STATUS_MASK, &raw);
+		if (ret < 0)
+			return ret;
 		/*
 		 * If power status mask has been reset, then the TCPC
 		 * has reset.
@@ -687,7 +696,9 @@ irqreturn_t tcpci_irq(struct tcpci *tcpci)
 		unsigned int cnt, payload_cnt;
 		u16 header;
 
-		regmap_read(tcpci->regmap, TCPC_RX_BYTE_CNT, &cnt);
+		ret = regmap_read(tcpci->regmap, TCPC_RX_BYTE_CNT, &cnt);
+		if (ret < 0)
+			return ret;
 		/*
 		 * 'cnt' corresponds to READABLE_BYTE_COUNT in section 4.4.14
 		 * of the TCPCI spec [Rev 2.0 Ver 1.0 October 2017] and is
@@ -699,18 +710,25 @@ irqreturn_t tcpci_irq(struct tcpci *tcpci)
 		else
 			payload_cnt = 0;
 
-		tcpci_read16(tcpci, TCPC_RX_HDR, &header);
+		ret = tcpci_read16(tcpci, TCPC_RX_HDR, &header);
+		if (ret < 0)
+			return ret;
 		msg.header = cpu_to_le16(header);
 
 		if (WARN_ON(payload_cnt > sizeof(msg.payload)))
 			payload_cnt = sizeof(msg.payload);
 
-		if (payload_cnt > 0)
-			regmap_raw_read(tcpci->regmap, TCPC_RX_DATA,
+		if (payload_cnt > 0) {
+			ret = regmap_raw_read(tcpci->regmap, TCPC_RX_DATA,
 					&msg.payload, payload_cnt);
+			if (ret < 0)
+				return ret;
+		}
 
 		/* Read complete, clear RX status alert bit */
-		tcpci_write16(tcpci, TCPC_ALERT, TCPC_ALERT_RX_STATUS);
+		ret = tcpci_write16(tcpci, TCPC_ALERT, TCPC_ALERT_RX_STATUS);
+		if (ret < 0)
+			return ret;
 
 		tcpm_pd_receive(tcpci->port, &msg);
 	}
-- 
2.34.1


             reply	other threads:[~2023-08-28  9:26 UTC|newest]

Thread overview: 5+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-08-28  9:30 Xu Yang [this message]
2023-08-28  9:30 ` [PATCH 2/2] usb: typec: tcpci: enable vSafe0v Detection and Auto Discharge Disconnect for PTN5110 Xu Yang
2023-08-28  9:49 ` [PATCH 1/2] usb: typec: tcpci: add check code for tcpci/regmap_read/write() Greg KH
2023-08-29  2:57   ` [EXT] " Xu Yang
  -- strict thread matches above, loose matches on Subject: below --
2023-09-14 12:09 Xu Yang

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20230828093035.1556639-1-xu.yang_2@nxp.com \
    --to=xu.yang_2@nxp.com \
    --cc=gregkh@linuxfoundation.org \
    --cc=heikki.krogerus@linux.intel.com \
    --cc=jun.li@nxp.com \
    --cc=linux-usb@vger.kernel.org \
    --cc=linux@roeck-us.net \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox