linux-usb.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
* [PATCH AUTOSEL 6.6 01/10] usb: chipidea: udc: create bounce buffer for problem sglist entries if possible
@ 2024-12-04 22:17 Sasha Levin
  2024-12-04 22:18 ` [PATCH AUTOSEL 6.6 02/10] usb: chipidea: udc: handle USB Error Interrupt if IOC not set Sasha Levin
  0 siblings, 1 reply; 2+ messages in thread
From: Sasha Levin @ 2024-12-04 22:17 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Xu Yang, Peter Chen, Greg Kroah-Hartman, Sasha Levin, peter.chen,
	linux-usb

From: Xu Yang <xu.yang_2@nxp.com>

[ Upstream commit edfcc455c85ccc5855f0c329ca5a2d85cc9fc6c6 ]

The chipidea controller doesn't fully support sglist, such as it can not
transfer data spanned more dTDs to form a bus packet, so it can only work
on very limited cases.

The limitations as below:
1. the end address of the first sg buffer must be 4KB aligned.
2. the start and end address of the middle sg buffer must be 4KB aligned.
3. the start address of the first sg buffer must be 4KB aligned.

However, not all the use cases violate these limitations. To make the
controller compatible with most of the cases, this will try to bounce the
problem sglist entries which can be found by sglist_get_invalid_entry().
Then a bounced line buffer (the size will roundup to page size) will be
allocated to replace the remaining problem sg entries. The data will be
copied between problem sg entries and bounce buffer according to the
transfer direction. The bounce buffer will be freed when the request
completed.

Acked-by: Peter Chen <peter.chen@kernel.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240923081203.2851768-3-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/usb/chipidea/udc.c | 148 +++++++++++++++++++++++++++++++++++++
 drivers/usb/chipidea/udc.h |   2 +
 2 files changed, 150 insertions(+)

diff --git a/drivers/usb/chipidea/udc.c b/drivers/usb/chipidea/udc.c
index f70ceedfb468f..bd409b18d01ba 100644
--- a/drivers/usb/chipidea/udc.c
+++ b/drivers/usb/chipidea/udc.c
@@ -10,6 +10,7 @@
 #include <linux/delay.h>
 #include <linux/device.h>
 #include <linux/dmapool.h>
+#include <linux/dma-direct.h>
 #include <linux/err.h>
 #include <linux/irqreturn.h>
 #include <linux/kernel.h>
@@ -540,6 +541,126 @@ static int prepare_td_for_sg(struct ci_hw_ep *hwep, struct ci_hw_req *hwreq)
 	return ret;
 }
 
+/*
+ * Verify if the scatterlist is valid by iterating each sg entry.
+ * Return invalid sg entry index which is less than num_sgs.
+ */
+static int sglist_get_invalid_entry(struct device *dma_dev, u8 dir,
+			struct usb_request *req)
+{
+	int i;
+	struct scatterlist *s = req->sg;
+
+	if (req->num_sgs == 1)
+		return 1;
+
+	dir = dir ? DMA_TO_DEVICE : DMA_FROM_DEVICE;
+
+	for (i = 0; i < req->num_sgs; i++, s = sg_next(s)) {
+		/* Only small sg (generally last sg) may be bounced. If
+		 * that happens. we can't ensure the addr is page-aligned
+		 * after dma map.
+		 */
+		if (dma_kmalloc_needs_bounce(dma_dev, s->length, dir))
+			break;
+
+		/* Make sure each sg start address (except first sg) is
+		 * page-aligned and end address (except last sg) is also
+		 * page-aligned.
+		 */
+		if (i == 0) {
+			if (!IS_ALIGNED(s->offset + s->length,
+						CI_HDRC_PAGE_SIZE))
+				break;
+		} else {
+			if (s->offset)
+				break;
+			if (!sg_is_last(s) && !IS_ALIGNED(s->length,
+						CI_HDRC_PAGE_SIZE))
+				break;
+		}
+	}
+
+	return i;
+}
+
+static int sglist_do_bounce(struct ci_hw_req *hwreq, int index,
+			bool copy, unsigned int *bounced)
+{
+	void *buf;
+	int i, ret, nents, num_sgs;
+	unsigned int rest, rounded;
+	struct scatterlist *sg, *src, *dst;
+
+	nents = index + 1;
+	ret = sg_alloc_table(&hwreq->sgt, nents, GFP_KERNEL);
+	if (ret)
+		return ret;
+
+	sg = src = hwreq->req.sg;
+	num_sgs = hwreq->req.num_sgs;
+	rest = hwreq->req.length;
+	dst = hwreq->sgt.sgl;
+
+	for (i = 0; i < index; i++) {
+		memcpy(dst, src, sizeof(*src));
+		rest -= src->length;
+		src = sg_next(src);
+		dst = sg_next(dst);
+	}
+
+	/* create one bounce buffer */
+	rounded = round_up(rest, CI_HDRC_PAGE_SIZE);
+	buf = kmalloc(rounded, GFP_KERNEL);
+	if (!buf) {
+		sg_free_table(&hwreq->sgt);
+		return -ENOMEM;
+	}
+
+	sg_set_buf(dst, buf, rounded);
+
+	hwreq->req.sg = hwreq->sgt.sgl;
+	hwreq->req.num_sgs = nents;
+	hwreq->sgt.sgl = sg;
+	hwreq->sgt.nents = num_sgs;
+
+	if (copy)
+		sg_copy_to_buffer(src, num_sgs - index, buf, rest);
+
+	*bounced = rest;
+
+	return 0;
+}
+
+static void sglist_do_debounce(struct ci_hw_req *hwreq, bool copy)
+{
+	void *buf;
+	int i, nents, num_sgs;
+	struct scatterlist *sg, *src, *dst;
+
+	sg = hwreq->req.sg;
+	num_sgs = hwreq->req.num_sgs;
+	src = sg_last(sg, num_sgs);
+	buf = sg_virt(src);
+
+	if (copy) {
+		dst = hwreq->sgt.sgl;
+		for (i = 0; i < num_sgs - 1; i++)
+			dst = sg_next(dst);
+
+		nents = hwreq->sgt.nents - num_sgs + 1;
+		sg_copy_from_buffer(dst, nents, buf, sg_dma_len(src));
+	}
+
+	hwreq->req.sg = hwreq->sgt.sgl;
+	hwreq->req.num_sgs = hwreq->sgt.nents;
+	hwreq->sgt.sgl = sg;
+	hwreq->sgt.nents = num_sgs;
+
+	kfree(buf);
+	sg_free_table(&hwreq->sgt);
+}
+
 /**
  * _hardware_enqueue: configures a request at hardware level
  * @hwep:   endpoint
@@ -552,6 +673,8 @@ static int _hardware_enqueue(struct ci_hw_ep *hwep, struct ci_hw_req *hwreq)
 	struct ci_hdrc *ci = hwep->ci;
 	int ret = 0;
 	struct td_node *firstnode, *lastnode;
+	unsigned int bounced_size;
+	struct scatterlist *sg;
 
 	/* don't queue twice */
 	if (hwreq->req.status == -EALREADY)
@@ -559,11 +682,29 @@ static int _hardware_enqueue(struct ci_hw_ep *hwep, struct ci_hw_req *hwreq)
 
 	hwreq->req.status = -EALREADY;
 
+	if (hwreq->req.num_sgs && hwreq->req.length &&
+		ci->has_short_pkt_limit) {
+		ret = sglist_get_invalid_entry(ci->dev->parent, hwep->dir,
+					&hwreq->req);
+		if (ret < hwreq->req.num_sgs) {
+			ret = sglist_do_bounce(hwreq, ret, hwep->dir == TX,
+					&bounced_size);
+			if (ret)
+				return ret;
+		}
+	}
+
 	ret = usb_gadget_map_request_by_dev(ci->dev->parent,
 					    &hwreq->req, hwep->dir);
 	if (ret)
 		return ret;
 
+	if (hwreq->sgt.sgl) {
+		/* We've mapped a bigger buffer, now recover the actual size */
+		sg = sg_last(hwreq->req.sg, hwreq->req.num_sgs);
+		sg_dma_len(sg) = min(sg_dma_len(sg), bounced_size);
+	}
+
 	if (hwreq->req.num_mapped_sgs)
 		ret = prepare_td_for_sg(hwep, hwreq);
 	else
@@ -732,6 +873,10 @@ static int _hardware_dequeue(struct ci_hw_ep *hwep, struct ci_hw_req *hwreq)
 	usb_gadget_unmap_request_by_dev(hwep->ci->dev->parent,
 					&hwreq->req, hwep->dir);
 
+	/* sglist bounced */
+	if (hwreq->sgt.sgl)
+		sglist_do_debounce(hwreq, hwep->dir == RX);
+
 	hwreq->req.actual += actual;
 
 	if (hwreq->req.status)
@@ -1573,6 +1718,9 @@ static int ep_dequeue(struct usb_ep *ep, struct usb_request *req)
 
 	usb_gadget_unmap_request(&hwep->ci->gadget, req, hwep->dir);
 
+	if (hwreq->sgt.sgl)
+		sglist_do_debounce(hwreq, false);
+
 	req->status = -ECONNRESET;
 
 	if (hwreq->req.complete != NULL) {
diff --git a/drivers/usb/chipidea/udc.h b/drivers/usb/chipidea/udc.h
index 5193df1e18c75..c8a47389a46bb 100644
--- a/drivers/usb/chipidea/udc.h
+++ b/drivers/usb/chipidea/udc.h
@@ -69,11 +69,13 @@ struct td_node {
  * @req: request structure for gadget drivers
  * @queue: link to QH list
  * @tds: link to TD list
+ * @sgt: hold original sglist when bounce sglist
  */
 struct ci_hw_req {
 	struct usb_request	req;
 	struct list_head	queue;
 	struct list_head	tds;
+	struct sg_table		sgt;
 };
 
 #ifdef CONFIG_USB_CHIPIDEA_UDC
-- 
2.43.0


^ permalink raw reply related	[flat|nested] 2+ messages in thread

* [PATCH AUTOSEL 6.6 02/10] usb: chipidea: udc: handle USB Error Interrupt if IOC not set
  2024-12-04 22:17 [PATCH AUTOSEL 6.6 01/10] usb: chipidea: udc: create bounce buffer for problem sglist entries if possible Sasha Levin
@ 2024-12-04 22:18 ` Sasha Levin
  0 siblings, 0 replies; 2+ messages in thread
From: Sasha Levin @ 2024-12-04 22:18 UTC (permalink / raw)
  To: linux-kernel, stable
  Cc: Xu Yang, Peter Chen, Greg Kroah-Hartman, Sasha Levin, peter.chen,
	linux-usb

From: Xu Yang <xu.yang_2@nxp.com>

[ Upstream commit 548f48b66c0c5d4b9795a55f304b7298cde2a025 ]

As per USBSTS register description about UEI:

  When completion of a USB transaction results in an error condition, this
  bit is set by the Host/Device Controller. This bit is set along with the
  USBINT bit, if the TD on which the error interrupt occurred also had its
  interrupt on complete (IOC) bit set.

UI is set only when IOC set. Add checking UEI to fix miss call
isr_tr_complete_handler() when IOC have not set and transfer error happen.

Acked-by: Peter Chen <peter.chen@kernel.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20240926022906.473319-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/usb/chipidea/udc.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/usb/chipidea/udc.c b/drivers/usb/chipidea/udc.c
index bd409b18d01ba..969d0825583a9 100644
--- a/drivers/usb/chipidea/udc.c
+++ b/drivers/usb/chipidea/udc.c
@@ -2210,7 +2210,7 @@ static irqreturn_t udc_irq(struct ci_hdrc *ci)
 			}
 		}
 
-		if (USBi_UI  & intr)
+		if ((USBi_UI | USBi_UEI) & intr)
 			isr_tr_complete_handler(ci);
 
 		if ((USBi_SLI & intr) && !(ci->suspended)) {
-- 
2.43.0


^ permalink raw reply related	[flat|nested] 2+ messages in thread

end of thread, other threads:[~2024-12-04 23:29 UTC | newest]

Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2024-12-04 22:17 [PATCH AUTOSEL 6.6 01/10] usb: chipidea: udc: create bounce buffer for problem sglist entries if possible Sasha Levin
2024-12-04 22:18 ` [PATCH AUTOSEL 6.6 02/10] usb: chipidea: udc: handle USB Error Interrupt if IOC not set Sasha Levin

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).