Re: [PATCH v4] thunderbolt: Disable Gen 4 Recovery on Asymmetric Transitions

[Mika Westerberg <mika.westerberg@linux.intel.com>]

Hi,

On Fri, Jan 31, 2025 at 01:41:27AM +0000, Mohammad Rahimi wrote:
> Updates the Connection Manager to disable the Gen 4 Link Recovery
> flow before transitioning from a Symmetric Link to an Asymmetric
> Link, as specified in recent changes to the USB4 v2 specification.
> 
> According to the "USB4 2.0 ENGINEERING CHANGE NOTICE FORM"
> published in September 2024, the rationale for this change is:
> 
>   "Since the default value of the Target Asymmetric Link might be
>   different than Symmetric Link and Gen 4 Link Recovery flow checks
>   this field to make sure it matched the actual Negotiated Link Width,
>   we’re removing the condition for a Disconnect in the Gen 4 Link
>   Recovery flow when Target Asymmetric Link doesn’t match the actual
>   Link width and adding a Connection Manager note to Disable Gen 4 Link
>   Recovery flow before doing Asymmetric Transitions."
> 
> Signed-off-by: Mohammad Rahimi <rahimi.mhmmd@gmail.com>

I did some minor modifications and applied to thunderbolt.git/next. Please
let me know if I missed something.

I tested on Intel reference hardware as well but on those link recovery is
already disabled so it pretty much does nothing. Below are the steps that I
followed:

1. Boot with "thunderbolt.asym_threshold=10000" so that the driver switches
   links to asymmetric already upon first DP connect.

2. Connect USB4 v2 hub.
3. Check link and PORT_CS_19:

# tblist -v
Domain 0 Route 0: 8087:5781 Intel Barlow Host Router
  Type: Router
  UUID: c9680000...
  Generation: USB4
  NVM version: 56.81

Domain 0 Route 1: 8087:1234 Intel Barlow HUB Router
  Type: Router
  Speed (Rx/Tx): 80/80 Gb/s
  Authorized: No
  UUID: e9688780...
  Generation: USB4
  NVM version: 56.81

# tbdump -r 0 -a 1 -vv -N 1 PORT_CS_19
0x00d3 0x0004000e 0b00000000 00000100 00000000 00001110 .... PORT_CS_19     
  [00:00]        0x0 Downstream Port Reset (DPR)
  [01:01]        0x1 Request RS-FEC Gen 2 (RS2)
  [02:02]        0x1 Request RS-FEC Gen 3 (RS3)
  [03:03]        0x1 USB4 Port is Configured (PC)
  [04:04]        0x0 USB4 Port is Inter-Domain (PID)
  [16:16]        0x0 Enable Wake on Connect
  [17:17]        0x0 Enable Wake on Disconnect
  [18:18]        0x1 Enable Wake on USB4 Wake
  [19:19]        0x0 Enable Wake on Inter-Domain
  [24:24]        0x0 StartAsymmetricFlow
  [30:30]        0x0 Initiate Gen 4 Link Recovery (ILR)
  [31:31]        0x0 Enable Gen 4 Link Recovery (ELR)

# tbdump -r 1 -a 1 -vv -N 1 PORT_CS_19
0x00d3 0x0004000e 0b00000000 00000100 00000000 00001110 .... PORT_CS_19     
  [00:00]        0x0 Downstream Port Reset (DPR)
  [01:01]        0x1 Request RS-FEC Gen 2 (RS2)
  [02:02]        0x1 Request RS-FEC Gen 3 (RS3)
  [03:03]        0x1 USB4 Port is Configured (PC)
  [04:04]        0x0 USB4 Port is Inter-Domain (PID)
  [16:16]        0x0 Enable Wake on Connect
  [17:17]        0x0 Enable Wake on Disconnect
  [18:18]        0x1 Enable Wake on USB4 Wake
  [19:19]        0x0 Enable Wake on Inter-Domain
  [24:24]        0x0 StartAsymmetricFlow
  [30:30]        0x0 Initiate Gen 4 Link Recovery (ILR)
  [31:31]        0x0 Enable Gen 4 Link Recovery (ELR)

3. Connect monitor to USB4 v2 hub.
4. Check link and PORT_CS_19.

# tblist -v
Domain 0 Route 0: 8087:5781 Intel Barlow Host Router
  Type: Router
  UUID: c9680000...
  Generation: USB4
  NVM version: 56.81

Domain 0 Route 1: 8087:1234 Intel Barlow HUB Router
  Type: Router
  Speed (Rx/Tx): 120/40 Gb/s
  Authorized: No
  UUID: e9688780...
  Generation: USB4
  NVM version: 56.81

# tbdump -r 0 -a 1 -vv -N 1 PORT_CS_19
0x00d3 0x0004000e 0b00000000 00000100 00000000 00001110 .... PORT_CS_19
  [00:00]        0x0 Downstream Port Reset (DPR)
  [01:01]        0x1 Request RS-FEC Gen 2 (RS2)
  [02:02]        0x1 Request RS-FEC Gen 3 (RS3)
  [03:03]        0x1 USB4 Port is Configured (PC)
  [04:04]        0x0 USB4 Port is Inter-Domain (PID)
  [16:16]        0x0 Enable Wake on Connect
  [17:17]        0x0 Enable Wake on Disconnect
  [18:18]        0x1 Enable Wake on USB4 Wake
  [19:19]        0x0 Enable Wake on Inter-Domain
  [24:24]        0x0 StartAsymmetricFlow
  [30:30]        0x0 Initiate Gen 4 Link Recovery (ILR)
  [31:31]        0x0 Enable Gen 4 Link Recovery (ELR)

# tbdump -r 1 -a 1 -vv -N 1 PORT_CS_19
0x00d3 0x0004000e 0b00000000 00000100 00000000 00001110 .... PORT_CS_19
  [00:00]        0x0 Downstream Port Reset (DPR)
  [01:01]        0x1 Request RS-FEC Gen 2 (RS2)
  [02:02]        0x1 Request RS-FEC Gen 3 (RS3)
  [03:03]        0x1 USB4 Port is Configured (PC)
  [04:04]        0x0 USB4 Port is Inter-Domain (PID)
  [16:16]        0x0 Enable Wake on Connect
  [17:17]        0x0 Enable Wake on Disconnect
  [18:18]        0x1 Enable Wake on USB4 Wake
  [19:19]        0x0 Enable Wake on Inter-Domain
  [24:24]        0x0 StartAsymmetricFlow
  [30:30]        0x0 Initiate Gen 4 Link Recovery (ILR)
  [31:31]        0x0 Enable Gen 4 Link Recovery (ELR)