From: Mathias Nyman <mathias.nyman@linux.intel.com>
To: <gregkh@linuxfoundation.org>
Cc: <linux-usb@vger.kernel.org>,
Niklas Neronin <niklas.neronin@linux.intel.com>,
Mathias Nyman <mathias.nyman@linux.intel.com>
Subject: [PATCH 03/24] usb: xhci: relocate pre-allocation initialization
Date: Thu, 15 May 2025 16:56:00 +0300 [thread overview]
Message-ID: <20250515135621.335595-4-mathias.nyman@linux.intel.com> (raw)
In-Reply-To: <20250515135621.335595-1-mathias.nyman@linux.intel.com>
From: Niklas Neronin <niklas.neronin@linux.intel.com>
Move pre-allocation initialization from xhci_mem_init() to xhci_init().
This change is part of an ongoing effort to separate initialization from
allocation within the xhci driver. By doing so, it will enable future
patches to re-initialize xhci driver memory without the necessity of fully
recreating it.
Additionally, compliance mode recovery initialization has been adjusted to
only occur after successful memory allocation.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
---
drivers/usb/host/xhci-mem.c | 28 ----------------------------
drivers/usb/host/xhci.c | 29 ++++++++++++++++++++++++++---
2 files changed, 26 insertions(+), 31 deletions(-)
diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c
index 7ff6a47d3198..a7955e02905c 100644
--- a/drivers/usb/host/xhci-mem.c
+++ b/drivers/usb/host/xhci-mem.c
@@ -2414,22 +2414,6 @@ xhci_create_secondary_interrupter(struct usb_hcd *hcd, unsigned int segs,
}
EXPORT_SYMBOL_GPL(xhci_create_secondary_interrupter);
-static void xhci_hcd_page_size(struct xhci_hcd *xhci)
-{
- u32 page_size;
-
- page_size = readl(&xhci->op_regs->page_size) & XHCI_PAGE_SIZE_MASK;
- if (!is_power_of_2(page_size)) {
- xhci_warn(xhci, "Invalid page size register = 0x%x\n", page_size);
- /* Fallback to 4K page size, since that's common */
- page_size = 1;
- }
-
- xhci->page_size = page_size << 12;
- xhci_dbg_trace(xhci, trace_xhci_dbg_init, "HCD page size set to %iK",
- xhci->page_size >> 10);
-}
-
int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags)
{
struct xhci_interrupter *ir;
@@ -2438,15 +2422,6 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags)
unsigned int val, val2;
u64 val_64;
u32 temp;
- int i;
-
- INIT_LIST_HEAD(&xhci->cmd_list);
-
- /* init command timeout work */
- INIT_DELAYED_WORK(&xhci->cmd_timer, xhci_handle_command_timeout);
- init_completion(&xhci->cmd_ring_stop_completion);
-
- xhci_hcd_page_size(xhci);
/*
* Program the Number of Device Slots Enabled field in the CONFIG
@@ -2567,9 +2542,6 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags)
ir->isoc_bei_interval = AVOID_BEI_INTERVAL_MAX;
- for (i = 0; i < MAX_HC_SLOTS; i++)
- xhci->devs[i] = NULL;
-
if (scratchpad_alloc(xhci, flags))
goto fail;
if (xhci_setup_port_arrays(xhci, flags))
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index fd9d41fe3224..b073e9d91665 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -461,6 +461,21 @@ static int xhci_all_ports_seen_u0(struct xhci_hcd *xhci)
return (xhci->port_status_u0 == ((1 << xhci->usb3_rhub.num_ports) - 1));
}
+static void xhci_hcd_page_size(struct xhci_hcd *xhci)
+{
+ u32 page_size;
+
+ page_size = readl(&xhci->op_regs->page_size) & XHCI_PAGE_SIZE_MASK;
+ if (!is_power_of_2(page_size)) {
+ xhci_warn(xhci, "Invalid page size register = 0x%x\n", page_size);
+ /* Fallback to 4K page size, since that's common */
+ page_size = 1;
+ }
+
+ xhci->page_size = page_size << 12;
+ xhci_dbg_trace(xhci, trace_xhci_dbg_init, "HCD page size set to %iK",
+ xhci->page_size >> 10);
+}
/*
* Initialize memory for HCD and xHC (one-time init).
@@ -474,11 +489,18 @@ static int xhci_init(struct usb_hcd *hcd)
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
int retval;
- xhci_dbg_trace(xhci, trace_xhci_dbg_init, "xhci_init");
+ xhci_dbg_trace(xhci, trace_xhci_dbg_init, "Starting %s", __func__);
spin_lock_init(&xhci->lock);
+ INIT_LIST_HEAD(&xhci->cmd_list);
+ INIT_DELAYED_WORK(&xhci->cmd_timer, xhci_handle_command_timeout);
+ init_completion(&xhci->cmd_ring_stop_completion);
+ xhci_hcd_page_size(xhci);
+ memset(xhci->devs, 0, MAX_HC_SLOTS * sizeof(*xhci->devs));
+
retval = xhci_mem_init(xhci, GFP_KERNEL);
- xhci_dbg_trace(xhci, trace_xhci_dbg_init, "Finished xhci_init");
+ if (retval)
+ return retval;
/* Initializing Compliance Mode Recovery Data If Needed */
if (xhci_compliance_mode_recovery_timer_quirk_check()) {
@@ -486,7 +508,8 @@ static int xhci_init(struct usb_hcd *hcd)
compliance_mode_recovery_timer_init(xhci);
}
- return retval;
+ xhci_dbg_trace(xhci, trace_xhci_dbg_init, "Finished %s", __func__);
+ return 0;
}
/*-------------------------------------------------------------------------*/
--
2.43.0
next prev parent reply other threads:[~2025-05-15 13:56 UTC|newest]
Thread overview: 36+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-05-15 13:55 [PATCH 00/24] xhci features for usb-next Mathias Nyman
2025-05-15 13:55 ` [PATCH 01/24] usb: xhci: Don't log transfer ring segment list on errors Mathias Nyman
2025-05-15 13:55 ` [PATCH 02/24] usb: xhci: Add debugfs support for xHCI port bandwidth Mathias Nyman
2025-05-15 13:56 ` Mathias Nyman [this message]
2025-05-15 13:56 ` [PATCH 04/24] usb: xhci: move device slot enabling register write Mathias Nyman
2025-05-15 13:56 ` [PATCH 05/24] usb: xhci: move command ring pointer write Mathias Nyman
2025-05-15 13:56 ` [PATCH 06/24] usb: xhci: refactor xhci_set_cmd_ring_deq() Mathias Nyman
2025-05-15 13:56 ` [PATCH 07/24] usb: xhci: move DCBAA pointer write Mathias Nyman
2025-05-15 13:56 ` [PATCH 08/24] usb: xhci: move doorbell array pointer assignment Mathias Nyman
2025-05-15 13:56 ` [PATCH 09/24] usb: xhci: move enabling of USB 3 device notifications Mathias Nyman
2025-05-15 13:56 ` [PATCH 10/24] usb: xhci: remove error handling from xhci_add_interrupter() Mathias Nyman
2025-05-15 13:56 ` [PATCH 11/24] usb: xhci: move initialization of the primary interrupter Mathias Nyman
2025-05-15 13:56 ` [PATCH 12/24] usb: xhci: add individual allocation checks in xhci_mem_init() Mathias Nyman
2025-05-15 13:56 ` [PATCH 13/24] usb: xhci: cleanup xhci_mem_init() Mathias Nyman
2025-05-15 13:56 ` [PATCH 14/24] usb: xhci: set requested IMODI to the closest supported value Mathias Nyman
2025-05-15 13:56 ` [PATCH 15/24] usb: xhci: improve Interrupt Management register macros Mathias Nyman
2025-05-15 13:56 ` [PATCH 16/24] usb: xhci: guarantee that IMAN register is flushed Mathias Nyman
2025-05-15 13:56 ` [PATCH 17/24] usb: xhci: remove '0' write to write-1-to-clear register Mathias Nyman
2025-05-15 13:56 ` [PATCH 18/24] usb: xhci: rework Event Ring Segment Table Size mask Mathias Nyman
2025-05-15 13:56 ` [PATCH 19/24] usb: xhci: rework Event Ring Segment Table Address mask Mathias Nyman
2025-05-15 13:56 ` [PATCH 20/24] usb: xhci: cleanup IMOD register comments Mathias Nyman
2025-05-15 13:56 ` [PATCH 21/24] usb: xhci: rename 'irq_pending' to 'iman' Mathias Nyman
2025-05-15 13:56 ` [PATCH 22/24] usb: xhci: rename 'irq_control' to 'imod' Mathias Nyman
2025-05-15 13:56 ` [PATCH 23/24] usb: xhci: add warning message specifying which Set TR Deq failed Mathias Nyman
2025-05-16 12:43 ` Michał Pecio
2025-05-16 14:32 ` Neronin, Niklas
2025-05-19 14:33 ` Mathias Nyman
2025-05-21 10:34 ` Greg KH
2025-05-21 13:22 ` Mathias Nyman
2025-05-15 13:56 ` [PATCH 24/24] xhci: Add host support for eUSB2 double isochronous bandwidth devices Mathias Nyman
2025-05-16 0:27 ` Thinh Nguyen
2025-05-16 0:40 ` Thinh Nguyen
2025-05-16 11:58 ` Mathias Nyman
2025-05-17 0:16 ` Thinh Nguyen
2025-05-21 10:36 ` [PATCH 00/24] xhci features for usb-next Greg KH
2025-05-21 13:24 ` Mathias Nyman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250515135621.335595-4-mathias.nyman@linux.intel.com \
--to=mathias.nyman@linux.intel.com \
--cc=gregkh@linuxfoundation.org \
--cc=linux-usb@vger.kernel.org \
--cc=niklas.neronin@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox