From: "Peter Chen (CIX)" <peter.chen@kernel.org>
To: Xu Yang <xu.yang_2@nxp.com>
Cc: gregkh@linuxfoundation.org, shawnguo@kernel.org,
john.ernberg@actia.se, jun.li@nxp.com, linux-usb@vger.kernel.org,
imx@lists.linux.dev
Subject: Re: [PATCH] usb: chipidea: udc: disconnect/reconnect from host when do suspend/resume
Date: Wed, 18 Jun 2025 18:33:23 +0800 [thread overview]
Message-ID: <20250618103323.GA34284@nchen-desktop> (raw)
In-Reply-To: <20250614124914.207540-1-xu.yang_2@nxp.com>
On 25-06-14 20:49:14, Xu Yang wrote:
> Shawn and John reported a hang issue during system suspend as below:
>
> - USB gadget is enabled as Ethernet
> - There is data transfer over USB Ethernet (scp a big file between host
> and device)
> - Device is going in/out suspend (echo mem > /sys/power/state)
>
> The root cause is the USB device controller is suspended but the USB bus
> is still active which caused the USB host continues to transfer data with
> device and the device continues to queue USB requests (in this case, a
> delayed TCP ACK packet trigger the issue) after controller is suspended,
> however the USB controller clock is already gated off. Then if udc driver
> access registers after that point, the system will hang.
>
> The correct way to avoid such issue is to disconnect device from host when
> the USB bus is not at suspend state. Then the host will receive disconnect
> event and stop data transfer in time. To continue make USB gadget device
> work after system resume, this will reconnect device automatically.
>
> To make usb wakeup work if USB bus is already at suspend state, this will
> keep connection for it only when USB device controller has enabled wakeup
> capability.
>
> Reported-by: Shawn Guo <shawnguo@kernel.org>
> Reported-by: John Ernberg <john.ernberg@actia.se>
> Closes: https://lore.kernel.org/linux-usb/aEZxmlHmjeWcXiF3@dragon/
> Tested-by: John Ernberg <john.ernberg@actia.se> # iMX8QXP
> Fixes: 235ffc17d014 ("usb: chipidea: udc: add suspend/resume support for device controller")
> Cc: stable@vger.kernel.org
> Reviewed-by: Jun Li <jun.li@nxp.com>
> Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Acked-by: Peter Chen <peter.chen@kernel.org>
Peter
> ---
> drivers/usb/chipidea/udc.c | 7 +++++++
> 1 file changed, 7 insertions(+)
>
> diff --git a/drivers/usb/chipidea/udc.c b/drivers/usb/chipidea/udc.c
> index 8a9b31fd5c89..1a48e6440e6c 100644
> --- a/drivers/usb/chipidea/udc.c
> +++ b/drivers/usb/chipidea/udc.c
> @@ -2374,6 +2374,10 @@ static void udc_suspend(struct ci_hdrc *ci)
> */
> if (hw_read(ci, OP_ENDPTLISTADDR, ~0) == 0)
> hw_write(ci, OP_ENDPTLISTADDR, ~0, ~0);
> +
> + if (ci->gadget.connected &&
> + (!ci->suspended || !device_may_wakeup(ci->dev)))
> + usb_gadget_disconnect(&ci->gadget);
> }
>
> static void udc_resume(struct ci_hdrc *ci, bool power_lost)
> @@ -2384,6 +2388,9 @@ static void udc_resume(struct ci_hdrc *ci, bool power_lost)
> OTGSC_BSVIS | OTGSC_BSVIE);
> if (ci->vbus_active)
> usb_gadget_vbus_disconnect(&ci->gadget);
> + } else if (ci->vbus_active && ci->driver &&
> + !ci->gadget.connected) {
> + usb_gadget_connect(&ci->gadget);
> }
>
> /* Restore value 0 if it was set for power lost check */
> --
> 2.34.1
>
--
Best regards,
Peter
prev parent reply other threads:[~2025-06-18 10:33 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-06-14 12:49 [PATCH] usb: chipidea: udc: disconnect/reconnect from host when do suspend/resume Xu Yang
2025-06-17 8:22 ` Peter Chen (CIX)
2025-06-18 5:52 ` Xu Yang
2025-06-18 10:33 ` Peter Chen (CIX) [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250618103323.GA34284@nchen-desktop \
--to=peter.chen@kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=imx@lists.linux.dev \
--cc=john.ernberg@actia.se \
--cc=jun.li@nxp.com \
--cc=linux-usb@vger.kernel.org \
--cc=shawnguo@kernel.org \
--cc=xu.yang_2@nxp.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox