Linux USB
 help / color / mirror / Atom feed
From: Mario Limonciello <superm1@kernel.org>
To: Rishabh Jain <rishabh.jain1198@gmail.com>,
	Mathias Nyman <mathias.nyman@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
	Michal Pecio <michal.pecio@gmail.com>,
	linux-usb@vger.kernel.org, linux-kernel@vger.kernel.org,
	stable@vger.kernel.org
Subject: Re: [PATCH v5] usb: pci-quirks: always assert xHCI OS ownership
Date: Mon, 12 Oct 2026 15:14:14 -0500	[thread overview]
Message-ID: <7d64e267-8ca6-4130-bd4a-d80fb4224f72@kernel.org> (raw)
In-Reply-To: <178832755831.50581.1058201741431375556@gmail.com>

On 9/2/26 00:39, Rishabh Jain wrote:
> The xHCI ownership protocol requires the OS driver to assert the HC OS
> Owned semaphore before using the host controller, then wait for HC BIOS
> Owned to clear if firmware owns it.
> 
> quirk_usb_handoff_xhci() currently asserts OS Owned only when BIOS Owned
> is already set. If firmware leaves BIOS Owned clear, Linux uses the xHC
> while both ownership semaphores remain clear.
> 
> The timeout fallback also clears BIOS Owned using the original register
> value, which can clear OS Owned at the same time.
> 
> On an AMD PROM21 xHCI controller (1022:43fc), this caused every S3
> resume to terminate Controller Restore State with USBSTS 0x401. Linux
> then reset the host controller, both root hubs and the USB Bluetooth
> adapter.
> 
> The controller entered resume ready and halted with USBSTS 0x1.
> Endpoint state, 100 ms save/restore delays, scratchpads, the DCBAA,
> device contexts and command, event and transfer rings were verified not
> to cause the restore error.
> 
> Across four S3 cycles, asserting only HC OS Owned changed USBLEGSUP from
> 0x00000801 to 0x01000801 and eliminated the restore failure. Testing
> included the unmodified 7.1.8-ogc1.1.fc44.x86_64 distribution kernel
> using a test module that set the HC OS Owned semaphore. The same test
> was repeated after review with the same result. Clearing USBLEGCTLSTS
> was independently verified to be unnecessary.
> 
> Always assert OS Owned for controllers using the standard xHCI handoff,
> and leave the existing TI/Renesas forced handoff unchanged. Keep OS
> Owned asserted after the standard handoff, including when forcing BIOS
> Owned clear after a timeout, to prevent firmware from reclaiming the
> controller during subsequent suspends.
> 
> Fixes: 66d4eadd8d06 ("USB: xhci: BIOS handoff and HW initialization.")
> Cc: stable@vger.kernel.org
> Assisted-by: LLM
> Signed-off-by: Rishabh Jain <rishabh.jain1198@gmail.com>
> ---

Reviewed-by: Mario Limonciello (AMD) <superm1@kernel.org>

> I kept val unchanged for the error log, restored the original handshake
> formatting, and explicitly preserve OS Owned when forcing BIOS Owned
> clear after a timeout. Documented timeout issue in commit message.
> 
> I repeated the same S3 test on the unmodified
> 7.1.8-ogc1.1.fc44.x86_64 distribution kernel using the test module, with
> the same successful result.
> 
> Changes in v5:
> - Preserve the original ownership value for error logging.
> - Restore the original handshake formatting.
> - Explicitly retain OS Owned in the timeout fallback.
> 
>   drivers/usb/host/pci-quirks.c | 13 ++++++++-----
>   1 file changed, 8 insertions(+), 5 deletions(-)
> 
> diff --git a/drivers/usb/host/pci-quirks.c b/drivers/usb/host/pci-quirks.c
> index 0404489c2f6a..2b12a35e6f10 100644
> --- a/drivers/usb/host/pci-quirks.c
> +++ b/drivers/usb/host/pci-quirks.c
> @@ -1193,10 +1193,11 @@ static void quirk_usb_handoff_xhci(struct pci_dev *pdev)
>   			 && pdev->device == 0x0014)) {
>   		val = (val | XHCI_HC_OS_OWNED) & ~XHCI_HC_BIOS_OWNED;
>   		writel(val, base + ext_cap_offset);
> -	}
> -
> -	/* If the BIOS owns the HC, signal that the OS wants it, and wait */
> -	if (val & XHCI_HC_BIOS_OWNED) {
> +	} else {
> +		/*
> +		 * Perform the standard handoff and leave OS ownership set to
> +		 * keep the BIOS at bay during subsequent suspends.
> +		 */
>   		writel(val | XHCI_HC_OS_OWNED, base + ext_cap_offset);
>   
>   		/* Wait for 1 second with 10 microsecond polling interval */
> @@ -1208,7 +1209,9 @@ static void quirk_usb_handoff_xhci(struct pci_dev *pdev)
>   			dev_warn(&pdev->dev,
>   				 "xHCI BIOS handoff failed (BIOS bug ?) %08x\n",
>   				 val);
> -			writel(val & ~XHCI_HC_BIOS_OWNED, base + ext_cap_offset);
> +			writel((val | XHCI_HC_OS_OWNED) &
> +			       ~XHCI_HC_BIOS_OWNED,
> +			       base + ext_cap_offset);
>   		}
>   	}
>   


  reply	other threads:[~2026-10-12 20:14 UTC|newest]

Thread overview: 16+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-08-15  1:45 [PATCH] usb: pci-quirks: always assert xHCI OS ownership Rishabh Jain
2026-08-16 16:33 ` Mario Limonciello
2026-08-16 18:15   ` [PATCH v2] " Rishabh Jain
2026-08-31 10:09     ` Greg Kroah-Hartman
2026-08-31 21:11       ` [PATCH v3] " Rishabh Jain
2026-08-31 21:27         ` Mario Limonciello
2026-09-01 10:13         ` Michal Pecio
2026-09-02  1:24         ` [PATCH v4] " Rishabh Jain
2026-09-02  3:26           ` Michal Pecio
2026-09-02  5:39             ` [PATCH v5] " Rishabh Jain
2026-10-12 20:14               ` Mario Limonciello [this message]
2026-08-16 20:03   ` [PATCH] " Michal Pecio
2026-08-16 21:00     ` Mario Limonciello
2026-08-18 22:15       ` Michal Pecio
2026-08-21 20:52         ` Mario Limonciello
  -- strict thread matches above, loose matches on Subject: below --
2026-09-11 15:13 [PATCH v5] " McKenna Fan

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=7d64e267-8ca6-4130-bd4a-d80fb4224f72@kernel.org \
    --to=superm1@kernel.org \
    --cc=gregkh@linuxfoundation.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-usb@vger.kernel.org \
    --cc=mathias.nyman@intel.com \
    --cc=michal.pecio@gmail.com \
    --cc=rishabh.jain1198@gmail.com \
    --cc=stable@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox