Re: Deadlock under load with Linux 5.9 and other recent kernels

[Christian Hewitt <christianshewitt@gmail.com>]

> On 26 Sep 2020, at 4:13 pm, Jens Axboe <axboe@kernel.dk> wrote:
> 
> On 9/26/20 5:55 AM, Christian Hewitt wrote:
>>> 
>>> On 26 Sep 2020, at 2:51 pm, Jens Axboe <axboe@kernel.dk> wrote:
>>> 
>>> On 9/26/20 1:55 AM, Christian Hewitt wrote:
>>>> I am using an ARM SBC device with Amlogic S922X chip (Beelink
>>>> GS-King-X, an Android STB) to boot the Kodi mediacentre distro
>>>> LibreELEC (which I work on) although the issue is also reproducible
>>>> with Manjaro and Armbian on the same hardware, and with the GT-King
>>>> and GT-King Pro devices from the same vendor - all three devices are
>>>> using a common dtsi:
>>>> 
>>>> https://github.com/chewitt/linux/blob/amlogic-5.9-integ/arch/arm64/boot/dts/amlogic/meson-g12b-gsking-x.dts
>>>> https://github.com/chewitt/linux/blob/amlogic-5.9-integ/arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts
>>>> https://github.com/chewitt/linux/blob/amlogic-5.9-integ/arch/arm64/boot/dts/amlogic/meson-g12b-gtking.dts
>>>> https://github.com/chewitt/linux/blob/amlogic-5.9-integ/arch/arm64/boot/dts/amlogic/meson-g12b-w400.dtsi
>>>> 
>>>> I have schematics for the devices, but can only share those privately
>>>> on request.
>>>> 
>>>> For testing I am booting LibreELEC from SD card. The box has a 4TB
>>>> SATA drive internally connected with a USB > SATA bridge, see dmesg:
>>>> http://ix.io/2yLh and I connect a USB stick with a 4GB ISO file that I
>>>> copy to the internal SATA drive. Within 10-20 seconds of starting the
>>>> copy the box deadlocks needing a hard power cycle to recover. The
>>>> timing of the deadlock is variable but the device _always_ deadlocks.
>>>> Although I am using a simple copy use-case, there are similar reports
>>>> in Armbian forums performing tasks like installs/updates that involve
>>>> I/O loads.
>>>> 
>>>> Following advice in the #linux-amlogic IRC channel I added
>>>> CONFIG_SOFTLOCKUP_DETECTOR and CONFIG_DETECT_HUNG_TASK and was able to
>>>> get output on the HDMI screen (it is not possible to connect to UART
>>>> pins without destroying the box case). If you advance the following
>>>> video frame by frame in VLC you can see the output:
>>>> 
>>>> https://www.dropbox.com/s/klvcizim8cs5lze/lockup_clip.mov?dl=0
>>> 
>>> Try with this patch:
>>> 
>>> https://lore.kernel.org/linux-block/20200925191902.543953-1-shakeelb@google.com/
>> 
>> It still locks up approx. 25 seconds into the copy operation. Here’s the output in video again (a little blurry):
>> 
>> https://www.dropbox.com/s/3j2czaq509arg6g/lockup_clip2.mov?dl=0
> 
> Can you try and set CONFIG_SLUB in your .config instead of CONFIG_SLAB?

CONFIG_SLUB is already set, here’s the full defconfig http://paste.ubuntu.com/p/5BNdZv6J3c/

# dmesg | grep -i slub
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1

> Also, just take a picture, should be easier to get readable than a video.
> And the static trace is all that is needed.

This is from a GT-King Pro which someone reminded me has a large RS232 port on the rear:

https://pastebin.com/raw/sGtzgreN

Christian