[PATCH RFC v5 0/6] ARM: pxa: GPIO descriptor conversions

[PATCH RFC v5 0/6] ARM: pxa: GPIO descriptor conversions

[Duje Mihanović]

Hello,

Small series to convert some of the board files in the mach-pxa directory
to use the new GPIO descriptor interface.

Most notably, the am200epd, am300epd and Spitz matrix keypad among
others are not converted in this series.

Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
---
Changes in v5:
- Address maintainer comments:
  - Rename "reset generator" GPIO to "reset"
  - Rename ads7846_wait_for_sync() to ads7846_wait_for_sync_gpio()
  - Properly bail out when requesting USB host GPIO fails
  - Use dev_err_probe() when requesting touchscreen sync GPIO fails
  - Use static gpio_desc for gumstix bluetooth reset
- Pulse gumstix bluetooth reset line correctly (assert, then deassert)
- Fix style issue in ads7846_wait_for_sync_gpio()
- Update trailers
- Link to v4: https://lore.kernel.org/r/20231001-pxa-gpio-v4-0-0f3b975e6ed5@skole.hr

Changes in v4:
- Address maintainer comments:
  - Move wait_for_sync() from spitz.c to driver
  - Register LED platform device before getting its gpiod-s
- Add Linus' Reviewed-by
- Link to v3: https://lore.kernel.org/r/20230929-pxa-gpio-v3-0-af8d5e5d1f34@skole.hr

Changes in v3:
- Address maintainer comments:
  - Use GPIO_LOOKUP_IDX for LEDs
  - Drop unnecessary NULL assignments
  - Don't give up on *all* SPI devices if hsync cannot be set up
- Add Linus' Acked-by
- Link to v2: https://lore.kernel.org/r/20230926-pxa-gpio-v2-0-984464d165dd@skole.hr

Changes in v2:
- Address maintainer comments:
  - Change mentions of function to function()
  - Drop cast in OHCI driver dev_warn() call
  - Use %pe in OHCI and reset drivers
  - Use GPIO _optional() API in OHCI driver
  - Drop unnecessary not-null check in OHCI driver
  - Use pr_err() instead of printk() in reset driver
- Rebase on v6.6-rc3
- Link to v1: https://lore.kernel.org/r/20230924-pxa-gpio-v1-0-2805b87d8894@skole.hr

---
Duje Mihanović (6):
      ARM: pxa: Convert Spitz OHCI to GPIO descriptors
      ARM: pxa: Convert Spitz LEDs to GPIO descriptors
      ARM: pxa: Convert Spitz CF power control to GPIO descriptors
      ARM: pxa: Convert reset driver to GPIO descriptors
      ARM: pxa: Convert gumstix Bluetooth to GPIO descriptors
      input: ads7846: Move wait_for_sync() logic to driver

 arch/arm/mach-pxa/gumstix.c         | 22 ++++++------
 arch/arm/mach-pxa/reset.c           | 39 +++++++--------------
 arch/arm/mach-pxa/reset.h           |  3 +-
 arch/arm/mach-pxa/spitz.c           | 69 +++++++++++++++++++++++++------------
 drivers/input/touchscreen/ads7846.c | 22 ++++++++----
 drivers/usb/host/ohci-pxa27x.c      |  7 ++++
 include/linux/spi/ads7846.h         |  1 -
 7 files changed, 94 insertions(+), 69 deletions(-)
---
base-commit: 6465e260f48790807eef06b583b38ca9789b6072
change-id: 20230807-pxa-gpio-3ce25d574814

Best regards,
-- 
Duje Mihanović <duje.mihanovic@skole.hr>

[PATCH RFC v5 1/6] ARM: pxa: Convert Spitz OHCI to GPIO descriptors

[Duje Mihanović]

Sharp's Spitz board still uses the legacy GPIO interface for controlling
a GPIO pin related to the USB host controller.

Convert this function to use the new GPIO descriptor interface.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
---
 arch/arm/mach-pxa/spitz.c      | 13 ++++++-------
 drivers/usb/host/ohci-pxa27x.c |  7 +++++++
 2 files changed, 13 insertions(+), 7 deletions(-)

diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
index cc691b199429..535e2b2e997b 100644
--- a/arch/arm/mach-pxa/spitz.c
+++ b/arch/arm/mach-pxa/spitz.c
@@ -649,23 +649,22 @@ static inline void spitz_mmc_init(void) {}
  * USB Host
  ******************************************************************************/
 #if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+GPIO_LOOKUP_SINGLE(spitz_usb_host_gpio_table, "pxa27x-ohci", "gpio-pxa",
+		SPITZ_GPIO_USB_HOST, "usb-host", GPIO_ACTIVE_LOW);
+
 static int spitz_ohci_init(struct device *dev)
 {
-	int err;
-
-	err = gpio_request(SPITZ_GPIO_USB_HOST, "USB_HOST");
-	if (err)
-		return err;
+	gpiod_add_lookup_table(&spitz_usb_host_gpio_table);
 
 	/* Only Port 2 is connected, setup USB Port 2 Output Control Register */
 	UP2OCR = UP2OCR_HXS | UP2OCR_HXOE | UP2OCR_DPPDE | UP2OCR_DMPDE;
 
-	return gpio_direction_output(SPITZ_GPIO_USB_HOST, 1);
+	return 0;
 }
 
 static void spitz_ohci_exit(struct device *dev)
 {
-	gpio_free(SPITZ_GPIO_USB_HOST);
+	gpiod_remove_lookup_table(&spitz_usb_host_gpio_table);
 }
 
 static struct pxaohci_platform_data spitz_ohci_platform_data = {
diff --git a/drivers/usb/host/ohci-pxa27x.c b/drivers/usb/host/ohci-pxa27x.c
index 357d9aee38a3..876842b940c0 100644
--- a/drivers/usb/host/ohci-pxa27x.c
+++ b/drivers/usb/host/ohci-pxa27x.c
@@ -121,6 +121,7 @@ struct pxa27x_ohci {
 	void __iomem	*mmio_base;
 	struct regulator *vbus[3];
 	bool		vbus_enabled[3];
+	struct gpio_desc *usb_host;
 };
 
 #define to_pxa27x_ohci(hcd)	(struct pxa27x_ohci *)(hcd_to_ohci(hcd)->priv)
@@ -447,6 +448,10 @@ static int ohci_hcd_pxa27x_probe(struct platform_device *pdev)
 	pxa_ohci = to_pxa27x_ohci(hcd);
 	pxa_ohci->clk = usb_clk;
 	pxa_ohci->mmio_base = (void __iomem *)hcd->regs;
+	pxa_ohci->usb_host = gpiod_get_optional(&pdev->dev, "usb-host", GPIOD_OUT_LOW);
+	if (IS_ERR(pxa_ohci->usb_host))
+		return dev_err_probe(&pdev->dev, PTR_ERR(pxa_ohci->usb_host),
+				"failed to get USB host GPIO\n");
 
 	for (i = 0; i < 3; ++i) {
 		char name[6];
@@ -512,6 +517,8 @@ static void ohci_hcd_pxa27x_remove(struct platform_device *pdev)
 	for (i = 0; i < 3; ++i)
 		pxa27x_ohci_set_vbus_power(pxa_ohci, i, false);
 
+	gpiod_put(pxa_ohci->usb_host);
+
 	usb_put_hcd(hcd);
 }
 

-- 
2.42.0

Re: [PATCH RFC v5 1/6] ARM: pxa: Convert Spitz OHCI to GPIO descriptors

[Bartosz Golaszewski]

On Wed, Oct 4, 2023 at 4:56 PM Duje Mihanović <duje.mihanovic@skole.hr> wrote:
>
> Sharp's Spitz board still uses the legacy GPIO interface for controlling
> a GPIO pin related to the USB host controller.
>
> Convert this function to use the new GPIO descriptor interface.
>
> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
> Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
> ---
>  arch/arm/mach-pxa/spitz.c      | 13 ++++++-------
>  drivers/usb/host/ohci-pxa27x.c |  7 +++++++
>  2 files changed, 13 insertions(+), 7 deletions(-)
>
> diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
> index cc691b199429..535e2b2e997b 100644
> --- a/arch/arm/mach-pxa/spitz.c
> +++ b/arch/arm/mach-pxa/spitz.c
> @@ -649,23 +649,22 @@ static inline void spitz_mmc_init(void) {}
>   * USB Host
>   ******************************************************************************/
>  #if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
> +GPIO_LOOKUP_SINGLE(spitz_usb_host_gpio_table, "pxa27x-ohci", "gpio-pxa",
> +               SPITZ_GPIO_USB_HOST, "usb-host", GPIO_ACTIVE_LOW);
> +
>  static int spitz_ohci_init(struct device *dev)
>  {
> -       int err;
> -
> -       err = gpio_request(SPITZ_GPIO_USB_HOST, "USB_HOST");
> -       if (err)
> -               return err;
> +       gpiod_add_lookup_table(&spitz_usb_host_gpio_table);
>
>         /* Only Port 2 is connected, setup USB Port 2 Output Control Register */
>         UP2OCR = UP2OCR_HXS | UP2OCR_HXOE | UP2OCR_DPPDE | UP2OCR_DMPDE;
>
> -       return gpio_direction_output(SPITZ_GPIO_USB_HOST, 1);
> +       return 0;
>  }
>
>  static void spitz_ohci_exit(struct device *dev)
>  {
> -       gpio_free(SPITZ_GPIO_USB_HOST);
> +       gpiod_remove_lookup_table(&spitz_usb_host_gpio_table);
>  }
>
>  static struct pxaohci_platform_data spitz_ohci_platform_data = {
> diff --git a/drivers/usb/host/ohci-pxa27x.c b/drivers/usb/host/ohci-pxa27x.c
> index 357d9aee38a3..876842b940c0 100644
> --- a/drivers/usb/host/ohci-pxa27x.c
> +++ b/drivers/usb/host/ohci-pxa27x.c
> @@ -121,6 +121,7 @@ struct pxa27x_ohci {
>         void __iomem    *mmio_base;
>         struct regulator *vbus[3];
>         bool            vbus_enabled[3];
> +       struct gpio_desc *usb_host;
>  };
>
>  #define to_pxa27x_ohci(hcd)    (struct pxa27x_ohci *)(hcd_to_ohci(hcd)->priv)
> @@ -447,6 +448,10 @@ static int ohci_hcd_pxa27x_probe(struct platform_device *pdev)
>         pxa_ohci = to_pxa27x_ohci(hcd);
>         pxa_ohci->clk = usb_clk;
>         pxa_ohci->mmio_base = (void __iomem *)hcd->regs;
> +       pxa_ohci->usb_host = gpiod_get_optional(&pdev->dev, "usb-host", GPIOD_OUT_LOW);

Any reason not to use devm_gpiod_get_optional()?

Bart

> +       if (IS_ERR(pxa_ohci->usb_host))
> +               return dev_err_probe(&pdev->dev, PTR_ERR(pxa_ohci->usb_host),
> +                               "failed to get USB host GPIO\n");
>
>         for (i = 0; i < 3; ++i) {
>                 char name[6];
> @@ -512,6 +517,8 @@ static void ohci_hcd_pxa27x_remove(struct platform_device *pdev)
>         for (i = 0; i < 3; ++i)
>                 pxa27x_ohci_set_vbus_power(pxa_ohci, i, false);
>
> +       gpiod_put(pxa_ohci->usb_host);
> +
>         usb_put_hcd(hcd);
>  }
>
>
> --
> 2.42.0
>
>

[PATCH RFC v5 2/6] ARM: pxa: Convert Spitz LEDs to GPIO descriptors

[Duje Mihanović]

Sharp's Spitz board still uses the legacy GPIO interface for configuring
its two onboard LEDs.

Convert them to use the GPIO descriptor interface.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
---
 arch/arm/mach-pxa/spitz.c | 18 ++++++++++++++++--
 1 file changed, 16 insertions(+), 2 deletions(-)

diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
index 535e2b2e997b..b6a4085e9fb0 100644
--- a/arch/arm/mach-pxa/spitz.c
+++ b/arch/arm/mach-pxa/spitz.c
@@ -452,16 +452,25 @@ static inline void spitz_keys_init(void) {}
  * LEDs
  ******************************************************************************/
 #if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
+static struct gpiod_lookup_table spitz_led_gpio_table = {
+	.dev_id = "leds-gpio",
+	.table = {
+		GPIO_LOOKUP_IDX("pxa-gpio", SPITZ_GPIO_LED_ORANGE, NULL, 0,
+				GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP_IDX("pxa-gpio", SPITZ_GPIO_LED_GREEN, NULL, 1,
+				GPIO_ACTIVE_HIGH),
+		{ }
+	}
+};
+
 static struct gpio_led spitz_gpio_leds[] = {
 	{
 		.name			= "spitz:amber:charge",
 		.default_trigger	= "sharpsl-charge",
-		.gpio			= SPITZ_GPIO_LED_ORANGE,
 	},
 	{
 		.name			= "spitz:green:hddactivity",
 		.default_trigger	= "disk-activity",
-		.gpio			= SPITZ_GPIO_LED_GREEN,
 	},
 };
 
@@ -480,7 +489,12 @@ static struct platform_device spitz_led_device = {
 
 static void __init spitz_leds_init(void)
 {
+	gpiod_add_lookup_table(&spitz_led_gpio_table);
 	platform_device_register(&spitz_led_device);
+	spitz_gpio_leds[0].gpiod = gpiod_get_index(&spitz_led_device.dev,
+			NULL, 0, GPIOD_ASIS);
+	spitz_gpio_leds[1].gpiod = gpiod_get_index(&spitz_led_device.dev,
+			NULL, 1, GPIOD_ASIS);
 }
 #else
 static inline void spitz_leds_init(void) {}

-- 
2.42.0

Re: [PATCH RFC v5 2/6] ARM: pxa: Convert Spitz LEDs to GPIO descriptors

[Bartosz Golaszewski]

On Wed, Oct 4, 2023 at 4:56 PM Duje Mihanović <duje.mihanovic@skole.hr> wrote:
>
> Sharp's Spitz board still uses the legacy GPIO interface for configuring
> its two onboard LEDs.
>
> Convert them to use the GPIO descriptor interface.
>
> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
> Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
> ---
>  arch/arm/mach-pxa/spitz.c | 18 ++++++++++++++++--
>  1 file changed, 16 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
> index 535e2b2e997b..b6a4085e9fb0 100644
> --- a/arch/arm/mach-pxa/spitz.c
> +++ b/arch/arm/mach-pxa/spitz.c
> @@ -452,16 +452,25 @@ static inline void spitz_keys_init(void) {}
>   * LEDs
>   ******************************************************************************/
>  #if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
> +static struct gpiod_lookup_table spitz_led_gpio_table = {
> +       .dev_id = "leds-gpio",
> +       .table = {
> +               GPIO_LOOKUP_IDX("pxa-gpio", SPITZ_GPIO_LED_ORANGE, NULL, 0,
> +                               GPIO_ACTIVE_HIGH),
> +               GPIO_LOOKUP_IDX("pxa-gpio", SPITZ_GPIO_LED_GREEN, NULL, 1,
> +                               GPIO_ACTIVE_HIGH),
> +               { }
> +       }
> +};
> +
>  static struct gpio_led spitz_gpio_leds[] = {
>         {
>                 .name                   = "spitz:amber:charge",
>                 .default_trigger        = "sharpsl-charge",
> -               .gpio                   = SPITZ_GPIO_LED_ORANGE,
>         },
>         {
>                 .name                   = "spitz:green:hddactivity",
>                 .default_trigger        = "disk-activity",
> -               .gpio                   = SPITZ_GPIO_LED_GREEN,
>         },
>  };
>
> @@ -480,7 +489,12 @@ static struct platform_device spitz_led_device = {
>
>  static void __init spitz_leds_init(void)
>  {
> +       gpiod_add_lookup_table(&spitz_led_gpio_table);
>         platform_device_register(&spitz_led_device);
> +       spitz_gpio_leds[0].gpiod = gpiod_get_index(&spitz_led_device.dev,
> +                       NULL, 0, GPIOD_ASIS);
> +       spitz_gpio_leds[1].gpiod = gpiod_get_index(&spitz_led_device.dev,
> +                       NULL, 1, GPIOD_ASIS);

You're not using the con_id you specified in the lookup table. How
about using gpiod_get_array()?

Bart

>  }
>  #else
>  static inline void spitz_leds_init(void) {}
>
> --
> 2.42.0
>
>

[PATCH RFC v5 3/6] ARM: pxa: Convert Spitz CF power control to GPIO descriptors

[Duje Mihanović]

Sharp's Spitz board still uses the legacy GPIO interface for controlling
the power supply to its CF and SD card slots.

Convert it to use the GPIO descriptor interface.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
---
 arch/arm/mach-pxa/spitz.c | 20 ++++++++++++++++++--
 1 file changed, 18 insertions(+), 2 deletions(-)

diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
index b6a4085e9fb0..965354e64c68 100644
--- a/arch/arm/mach-pxa/spitz.c
+++ b/arch/arm/mach-pxa/spitz.c
@@ -133,6 +133,10 @@ static unsigned long spitz_pin_config[] __initdata = {
  * Scoop GPIO expander
  ******************************************************************************/
 #if defined(CONFIG_SHARP_SCOOP) || defined(CONFIG_SHARP_SCOOP_MODULE)
+GPIO_LOOKUP_SINGLE(spitz_card_pwr_ctrl_gpio_table, "pxa2xx-mci.0",
+		"sharp-scoop", SPITZ_GPIO_CF_POWER, "cf_power",
+		GPIO_ACTIVE_HIGH);
+
 /* SCOOP Device #1 */
 static struct resource spitz_scoop_1_resources[] = {
 	[0] = {
@@ -190,6 +194,7 @@ struct platform_device spitz_scoop_2_device = {
 static void __init spitz_scoop_init(void)
 {
 	platform_device_register(&spitz_scoop_1_device);
+	gpiod_add_lookup_table(&spitz_card_pwr_ctrl_gpio_table);
 
 	/* Akita doesn't have the second SCOOP chip */
 	if (!machine_is_akita())
@@ -201,9 +206,18 @@ static void __maybe_unused spitz_card_pwr_ctrl(uint8_t enable, uint8_t new_cpr)
 {
 	unsigned short cpr;
 	unsigned long flags;
+	struct gpio_desc *cf_power;
+
+	cf_power = gpiod_get(&pxa_device_mci.dev, "cf_power", GPIOD_ASIS);
+	if (IS_ERR(cf_power)) {
+		dev_err(&pxa_device_mci.dev,
+				"failed to get power control GPIO with %ld\n",
+				PTR_ERR(cf_power));
+		return;
+	}
 
 	if (new_cpr & 0x7) {
-		gpio_set_value(SPITZ_GPIO_CF_POWER, 1);
+		gpiod_direction_output(cf_power, 1);
 		mdelay(5);
 	}
 
@@ -222,8 +236,10 @@ static void __maybe_unused spitz_card_pwr_ctrl(uint8_t enable, uint8_t new_cpr)
 
 	if (!(cpr & 0x7)) {
 		mdelay(1);
-		gpio_set_value(SPITZ_GPIO_CF_POWER, 0);
+		gpiod_direction_output(cf_power, 0);
 	}
+
+	gpiod_put(cf_power);
 }
 
 #else

-- 
2.42.0

Re: [PATCH RFC v5 3/6] ARM: pxa: Convert Spitz CF power control to GPIO descriptors

[Bartosz Golaszewski]

On Wed, Oct 4, 2023 at 4:56 PM Duje Mihanović <duje.mihanovic@skole.hr> wrote:
>
> Sharp's Spitz board still uses the legacy GPIO interface for controlling
> the power supply to its CF and SD card slots.
>
> Convert it to use the GPIO descriptor interface.
>
> Acked-by: Linus Walleij <linus.walleij@linaro.org>
> Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
> ---

Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

[PATCH RFC v5 4/6] ARM: pxa: Convert reset driver to GPIO descriptors

[Duje Mihanović]

The PXA reset driver still uses the legacy GPIO interface for
configuring and asserting the reset pin.

Convert it to use the GPIO descriptor interface.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
---
 arch/arm/mach-pxa/reset.c | 39 +++++++++++++--------------------------
 arch/arm/mach-pxa/reset.h |  3 +--
 arch/arm/mach-pxa/spitz.c |  6 +++++-
 3 files changed, 19 insertions(+), 29 deletions(-)

diff --git a/arch/arm/mach-pxa/reset.c b/arch/arm/mach-pxa/reset.c
index 27293549f8ad..08bc104b9411 100644
--- a/arch/arm/mach-pxa/reset.c
+++ b/arch/arm/mach-pxa/reset.c
@@ -2,7 +2,7 @@
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/delay.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
 #include <linux/io.h>
 #include <asm/proc-fns.h>
 #include <asm/system_misc.h>
@@ -14,33 +14,20 @@
 
 static void do_hw_reset(void);
 
-static int reset_gpio = -1;
+static struct gpio_desc *reset_gpio;
 
-int init_gpio_reset(int gpio, int output, int level)
+int init_gpio_reset(int output, int level)
 {
-	int rc;
-
-	rc = gpio_request(gpio, "reset generator");
-	if (rc) {
-		printk(KERN_ERR "Can't request reset_gpio\n");
-		goto out;
+	reset_gpio = gpiod_get(NULL, "reset", GPIOD_ASIS);
+	if (IS_ERR(reset_gpio)) {
+		pr_err("Can't request reset_gpio: %pe\n", reset_gpio);
+		return PTR_ERR(reset_gpio);
 	}
 
 	if (output)
-		rc = gpio_direction_output(gpio, level);
+		return gpiod_direction_output(reset_gpio, level);
 	else
-		rc = gpio_direction_input(gpio);
-	if (rc) {
-		printk(KERN_ERR "Can't configure reset_gpio\n");
-		gpio_free(gpio);
-		goto out;
-	}
-
-out:
-	if (!rc)
-		reset_gpio = gpio;
-
-	return rc;
+		return gpiod_direction_input(reset_gpio);
 }
 
 /*
@@ -50,16 +37,16 @@ int init_gpio_reset(int gpio, int output, int level)
  */
 static void do_gpio_reset(void)
 {
-	BUG_ON(reset_gpio == -1);
+	BUG_ON(IS_ERR(reset_gpio));
 
 	/* drive it low */
-	gpio_direction_output(reset_gpio, 0);
+	gpiod_direction_output(reset_gpio, 0);
 	mdelay(2);
 	/* rising edge or drive high */
-	gpio_set_value(reset_gpio, 1);
+	gpiod_set_value(reset_gpio, 1);
 	mdelay(2);
 	/* falling edge */
-	gpio_set_value(reset_gpio, 0);
+	gpiod_set_value(reset_gpio, 0);
 
 	/* give it some time */
 	mdelay(10);
diff --git a/arch/arm/mach-pxa/reset.h b/arch/arm/mach-pxa/reset.h
index 963dd190bc13..5864f61a0e94 100644
--- a/arch/arm/mach-pxa/reset.h
+++ b/arch/arm/mach-pxa/reset.h
@@ -13,10 +13,9 @@ extern void pxa_register_wdt(unsigned int reset_status);
 
 /**
  * init_gpio_reset() - register GPIO as reset generator
- * @gpio: gpio nr
  * @output: set gpio as output instead of input during normal work
  * @level: output level
  */
-extern int init_gpio_reset(int gpio, int output, int level);
+extern int init_gpio_reset(int output, int level);
 
 #endif /* __ASM_ARCH_RESET_H */
diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
index 965354e64c68..26ec29c9cd1b 100644
--- a/arch/arm/mach-pxa/spitz.c
+++ b/arch/arm/mach-pxa/spitz.c
@@ -1024,9 +1024,13 @@ static void spitz_restart(enum reboot_mode mode, const char *cmd)
 	spitz_poweroff();
 }
 
+GPIO_LOOKUP_SINGLE(spitz_reset_gpio_table, NULL, "pxa-gpio",
+		SPITZ_GPIO_ON_RESET, "reset", GPIO_ACTIVE_HIGH);
+
 static void __init spitz_init(void)
 {
-	init_gpio_reset(SPITZ_GPIO_ON_RESET, 1, 0);
+	gpiod_add_lookup_table(&spitz_reset_gpio_table);
+	init_gpio_reset(1, 0);
 	pm_power_off = spitz_poweroff;
 
 	PMCR = 0x00;

-- 
2.42.0

Re: [PATCH RFC v5 4/6] ARM: pxa: Convert reset driver to GPIO descriptors

[Bartosz Golaszewski]

On Wed, Oct 4, 2023 at 4:56 PM Duje Mihanović <duje.mihanovic@skole.hr> wrote:
>
> The PXA reset driver still uses the legacy GPIO interface for
> configuring and asserting the reset pin.
>
> Convert it to use the GPIO descriptor interface.
>
> Acked-by: Linus Walleij <linus.walleij@linaro.org>
> Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
> ---
>  arch/arm/mach-pxa/reset.c | 39 +++++++++++++--------------------------
>  arch/arm/mach-pxa/reset.h |  3 +--
>  arch/arm/mach-pxa/spitz.c |  6 +++++-
>  3 files changed, 19 insertions(+), 29 deletions(-)
>
> diff --git a/arch/arm/mach-pxa/reset.c b/arch/arm/mach-pxa/reset.c
> index 27293549f8ad..08bc104b9411 100644
> --- a/arch/arm/mach-pxa/reset.c
> +++ b/arch/arm/mach-pxa/reset.c
> @@ -2,7 +2,7 @@
>  #include <linux/kernel.h>
>  #include <linux/module.h>
>  #include <linux/delay.h>
> -#include <linux/gpio.h>
> +#include <linux/gpio/consumer.h>
>  #include <linux/io.h>
>  #include <asm/proc-fns.h>
>  #include <asm/system_misc.h>
> @@ -14,33 +14,20 @@
>
>  static void do_hw_reset(void);
>
> -static int reset_gpio = -1;
> +static struct gpio_desc *reset_gpio;
>
> -int init_gpio_reset(int gpio, int output, int level)
> +int init_gpio_reset(int output, int level)
>  {
> -       int rc;
> -
> -       rc = gpio_request(gpio, "reset generator");
> -       if (rc) {
> -               printk(KERN_ERR "Can't request reset_gpio\n");
> -               goto out;
> +       reset_gpio = gpiod_get(NULL, "reset", GPIOD_ASIS);
> +       if (IS_ERR(reset_gpio)) {
> +               pr_err("Can't request reset_gpio: %pe\n", reset_gpio);
> +               return PTR_ERR(reset_gpio);
>         }
>
>         if (output)
> -               rc = gpio_direction_output(gpio, level);
> +               return gpiod_direction_output(reset_gpio, level);
>         else
> -               rc = gpio_direction_input(gpio);
> -       if (rc) {
> -               printk(KERN_ERR "Can't configure reset_gpio\n");
> -               gpio_free(gpio);
> -               goto out;
> -       }
> -
> -out:
> -       if (!rc)
> -               reset_gpio = gpio;
> -
> -       return rc;
> +               return gpiod_direction_input(reset_gpio);
>  }
>
>  /*
> @@ -50,16 +37,16 @@ int init_gpio_reset(int gpio, int output, int level)
>   */
>  static void do_gpio_reset(void)
>  {
> -       BUG_ON(reset_gpio == -1);
> +       BUG_ON(IS_ERR(reset_gpio));

Crashing the kernel on a GPIO error? I guess it just keeps the old
behavior but still...

>
>         /* drive it low */
> -       gpio_direction_output(reset_gpio, 0);
> +       gpiod_direction_output(reset_gpio, 0);
>         mdelay(2);
>         /* rising edge or drive high */
> -       gpio_set_value(reset_gpio, 1);
> +       gpiod_set_value(reset_gpio, 1);
>         mdelay(2);
>         /* falling edge */
> -       gpio_set_value(reset_gpio, 0);
> +       gpiod_set_value(reset_gpio, 0);
>
>         /* give it some time */
>         mdelay(10);
> diff --git a/arch/arm/mach-pxa/reset.h b/arch/arm/mach-pxa/reset.h
> index 963dd190bc13..5864f61a0e94 100644
> --- a/arch/arm/mach-pxa/reset.h
> +++ b/arch/arm/mach-pxa/reset.h
> @@ -13,10 +13,9 @@ extern void pxa_register_wdt(unsigned int reset_status);
>
>  /**
>   * init_gpio_reset() - register GPIO as reset generator
> - * @gpio: gpio nr
>   * @output: set gpio as output instead of input during normal work
>   * @level: output level
>   */
> -extern int init_gpio_reset(int gpio, int output, int level);
> +extern int init_gpio_reset(int output, int level);
>
>  #endif /* __ASM_ARCH_RESET_H */
> diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
> index 965354e64c68..26ec29c9cd1b 100644
> --- a/arch/arm/mach-pxa/spitz.c
> +++ b/arch/arm/mach-pxa/spitz.c
> @@ -1024,9 +1024,13 @@ static void spitz_restart(enum reboot_mode mode, const char *cmd)
>         spitz_poweroff();
>  }
>
> +GPIO_LOOKUP_SINGLE(spitz_reset_gpio_table, NULL, "pxa-gpio",
> +               SPITZ_GPIO_ON_RESET, "reset", GPIO_ACTIVE_HIGH);
> +
>  static void __init spitz_init(void)
>  {
> -       init_gpio_reset(SPITZ_GPIO_ON_RESET, 1, 0);
> +       gpiod_add_lookup_table(&spitz_reset_gpio_table);
> +       init_gpio_reset(1, 0);
>         pm_power_off = spitz_poweroff;
>
>         PMCR = 0x00;
>
> --
> 2.42.0
>
>

Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

[PATCH RFC v5 5/6] ARM: pxa: Convert gumstix Bluetooth to GPIO descriptors

[Duje Mihanović]

Gumstix still uses the legacy GPIO interface for resetting the Bluetooth
device.

Convert it to use the GPIO descriptor interface.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
---
 arch/arm/mach-pxa/gumstix.c | 22 +++++++++++-----------
 1 file changed, 11 insertions(+), 11 deletions(-)

diff --git a/arch/arm/mach-pxa/gumstix.c b/arch/arm/mach-pxa/gumstix.c
index c9f0f62187bd..0bca6e2c80a9 100644
--- a/arch/arm/mach-pxa/gumstix.c
+++ b/arch/arm/mach-pxa/gumstix.c
@@ -20,8 +20,8 @@
 #include <linux/delay.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
+#include <linux/gpio/consumer.h>
 #include <linux/gpio/machine.h>
-#include <linux/gpio.h>
 #include <linux/err.h>
 #include <linux/clk.h>
 
@@ -129,6 +129,11 @@ static void gumstix_udc_init(void)
 #endif
 
 #ifdef CONFIG_BT
+GPIO_LOOKUP_SINGLE(gumstix_bt_gpio_table, "pxa2xx-uart.1", "pxa-gpio",
+		GPIO_GUMSTIX_BTRESET, "BTRST", GPIO_ACTIVE_LOW);
+
+static struct gpio_desc *bt_reset;
+
 /* Normally, the bootloader would have enabled this 32kHz clock but many
 ** boards still have u-boot 1.1.4 so we check if it has been turned on and
 ** if not, we turn it on with a warning message. */
@@ -153,24 +158,19 @@ static void gumstix_setup_bt_clock(void)
 
 static void __init gumstix_bluetooth_init(void)
 {
-	int err;
+	gpiod_add_lookup_table(&gumstix_bt_gpio_table);
 
 	gumstix_setup_bt_clock();
 
-	err = gpio_request(GPIO_GUMSTIX_BTRESET, "BTRST");
-	if (err) {
+	bt_reset = gpiod_get(&pxa_device_btuart.dev, "BTRST", GPIOD_OUT_HIGH);
+	if (IS_ERR(bt_reset)) {
 		pr_err("gumstix: failed request gpio for bluetooth reset\n");
 		return;
 	}
 
-	err = gpio_direction_output(GPIO_GUMSTIX_BTRESET, 1);
-	if (err) {
-		pr_err("gumstix: can't reset bluetooth\n");
-		return;
-	}
-	gpio_set_value(GPIO_GUMSTIX_BTRESET, 0);
+	gpiod_set_value(bt_reset, 1);
 	udelay(100);
-	gpio_set_value(GPIO_GUMSTIX_BTRESET, 1);
+	gpiod_set_value(bt_reset, 0);
 }
 #else
 static void gumstix_bluetooth_init(void)

-- 
2.42.0

Re: [PATCH RFC v5 5/6] ARM: pxa: Convert gumstix Bluetooth to GPIO descriptors

[Bartosz Golaszewski]

On Wed, Oct 4, 2023 at 4:56 PM Duje Mihanović <duje.mihanovic@skole.hr> wrote:
>
> Gumstix still uses the legacy GPIO interface for resetting the Bluetooth
> device.
>
> Convert it to use the GPIO descriptor interface.
>
> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
> Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
> ---

Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

[PATCH RFC v5 6/6] input: ads7846: Move wait_for_sync() logic to driver

[Duje Mihanović]

If this code is left in the board file, the sync GPIO would have to be
separated into another lookup table during conversion to the GPIO
descriptor API (which is also done in this patch).

The only user of this code (Sharp Spitz) is also converted in this
patch.

Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
---
 arch/arm/mach-pxa/spitz.c           | 12 ++----------
 drivers/input/touchscreen/ads7846.c | 22 +++++++++++++++-------
 include/linux/spi/ads7846.h         |  1 -
 3 files changed, 17 insertions(+), 18 deletions(-)

diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
index 26ec29c9cd1b..e8bc0249b503 100644
--- a/arch/arm/mach-pxa/spitz.c
+++ b/arch/arm/mach-pxa/spitz.c
@@ -520,22 +520,12 @@ static inline void spitz_leds_init(void) {}
  * SSP Devices
  ******************************************************************************/
 #if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE)
-static void spitz_ads7846_wait_for_hsync(void)
-{
-	while (gpio_get_value(SPITZ_GPIO_HSYNC))
-		cpu_relax();
-
-	while (!gpio_get_value(SPITZ_GPIO_HSYNC))
-		cpu_relax();
-}
-
 static struct ads7846_platform_data spitz_ads7846_info = {
 	.model			= 7846,
 	.vref_delay_usecs	= 100,
 	.x_plate_ohms		= 419,
 	.y_plate_ohms		= 486,
 	.pressure_max		= 1024,
-	.wait_for_sync		= spitz_ads7846_wait_for_hsync,
 };
 
 static struct gpiod_lookup_table spitz_ads7846_gpio_table = {
@@ -543,6 +533,8 @@ static struct gpiod_lookup_table spitz_ads7846_gpio_table = {
 	.table = {
 		GPIO_LOOKUP("gpio-pxa", SPITZ_GPIO_TP_INT,
 			    "pendown", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("gpio-pxa", SPITZ_GPIO_HSYNC,
+			    "sync", GPIO_ACTIVE_LOW),
 		{ }
 	},
 };
diff --git a/drivers/input/touchscreen/ads7846.c b/drivers/input/touchscreen/ads7846.c
index faea40dd66d0..139b0f3735d0 100644
--- a/drivers/input/touchscreen/ads7846.c
+++ b/drivers/input/touchscreen/ads7846.c
@@ -138,8 +138,7 @@ struct ads7846 {
 	void			*filter_data;
 	int			(*get_pendown_state)(void);
 	struct gpio_desc	*gpio_pendown;
-
-	void			(*wait_for_sync)(void);
+	struct gpio_desc	*sync;
 };
 
 enum ads7846_filter {
@@ -636,9 +635,15 @@ static const struct attribute_group ads784x_attr_group = {
 };
 
 /*--------------------------------------------------------------------------*/
-
-static void null_wait_for_sync(void)
+static void ads7846_wait_for_sync_gpio(struct ads7846 *ts)
 {
+	if (!ts->sync)
+		return;
+	while (!gpiod_get_value(ts->sync))
+		cpu_relax();
+
+	while (gpiod_get_value(ts->sync))
+		cpu_relax();
 }
 
 static int ads7846_debounce_filter(void *ads, int data_idx, int *val)
@@ -803,7 +808,7 @@ static void ads7846_read_state(struct ads7846 *ts)
 	packet->last_cmd_idx = 0;
 
 	while (true) {
-		ts->wait_for_sync();
+		ads7846_wait_for_sync_gpio(ts);
 
 		m = &ts->msg[msg_idx];
 		error = spi_sync(ts->spi, m);
@@ -1261,8 +1266,6 @@ static int ads7846_probe(struct spi_device *spi)
 		ts->penirq_recheck_delay_usecs =
 				pdata->penirq_recheck_delay_usecs;
 
-	ts->wait_for_sync = pdata->wait_for_sync ? : null_wait_for_sync;
-
 	snprintf(ts->phys, sizeof(ts->phys), "%s/input0", dev_name(dev));
 	snprintf(ts->name, sizeof(ts->name), "ADS%d Touchscreen", ts->model);
 
@@ -1361,6 +1364,11 @@ static int ads7846_probe(struct spi_device *spi)
 	if (err)
 		return err;
 
+	ts->sync = devm_gpiod_get_optional(dev, "sync", GPIOD_IN);
+	if (IS_ERR(ts->sync))
+		return dev_err_probe(dev, PTR_ERR(ts->sync),
+				"Failed to get sync GPIO");
+
 	err = input_register_device(input_dev);
 	if (err)
 		return err;
diff --git a/include/linux/spi/ads7846.h b/include/linux/spi/ads7846.h
index a04c1c34c344..fa7c4f119023 100644
--- a/include/linux/spi/ads7846.h
+++ b/include/linux/spi/ads7846.h
@@ -38,7 +38,6 @@ struct ads7846_platform_data {
 	int	gpio_pendown_debounce;	/* platform specific debounce time for
 					 * the gpio_pendown */
 	int	(*get_pendown_state)(void);
-	void	(*wait_for_sync)(void);
 	bool	wakeup;
 	unsigned long irq_flags;
 };

-- 
2.42.0

Re: [PATCH RFC v5 6/6] input: ads7846: Move wait_for_sync() logic to driver

[Bartosz Golaszewski]

On Wed, Oct 4, 2023 at 4:56 PM Duje Mihanović <duje.mihanovic@skole.hr> wrote:
>
> If this code is left in the board file, the sync GPIO would have to be
> separated into another lookup table during conversion to the GPIO
> descriptor API (which is also done in this patch).
>
> The only user of this code (Sharp Spitz) is also converted in this
> patch.
>
> Suggested-by: Linus Walleij <linus.walleij@linaro.org>
> Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
> Acked-by: Mark Brown <broonie@kernel.org>
> Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
> ---

Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Re: [PATCH RFC v5 0/6] ARM: pxa: GPIO descriptor conversions

[Andy Shevchenko]

On Wed, Oct 04, 2023 at 04:56:24PM +0200, Duje Mihanović wrote:
> Hello,
> 
> Small series to convert some of the board files in the mach-pxa directory
> to use the new GPIO descriptor interface.
> 
> Most notably, the am200epd, am300epd and Spitz matrix keypad among
> others are not converted in this series.

Why is it still RFC?
I believe it's already good enough to be considered as a real material.
OTOH "RFT" might make sense. I'm not sure there are any users on the
planet Earth that have this Sharp device up and running with newest
kernels.


-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH RFC v5 0/6] ARM: pxa: GPIO descriptor conversions

[Duje Mihanović]

On Thursday, October 5, 2023 11:14:05 AM CEST Andy Shevchenko wrote:
> On Wed, Oct 04, 2023 at 04:56:24PM +0200, Duje Mihanović wrote:
> > Hello,
> > 
> > Small series to convert some of the board files in the mach-pxa directory
> > to use the new GPIO descriptor interface.
> > 
> > Most notably, the am200epd, am300epd and Spitz matrix keypad among
> > others are not converted in this series.
> 
> Why is it still RFC?
> I believe it's already good enough to be considered as a real material.
> OTOH "RFT" might make sense. I'm not sure there are any users on the
> planet Earth that have this Sharp device up and running with newest
> kernels.

Will add RFT in an eventual v6.

Regards,
Duje