[PATCH 0/3] TBT3/USB4 support for PS8830

[PATCH 0/3] TBT3/USB4 support for PS8830

[Konrad Dybcio]

As the product page [1] states, the chip is actually capable of
retiming USB4 and Thunderbolt 3 (4, even!) signals, while remaining
spec-compliant.

This series reworks the driver a little and introduces support for the
new aforementioned modes.

I carried Jack's Reviewed-by tags from an internal preview submission,
which I hope is fine with everyone.

Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
Konrad Dybcio (3):
      usb: typec: ps883x: Cache register settings, not Type-C mode
      usb: typec: ps883x: Rework ps883x_set()
      usb: typec: ps883x: Add USB4 mode and TBT3 altmode support

 drivers/usb/typec/mux/ps883x.c | 129 ++++++++++++++++++++++++++---------------
 include/linux/usb/typec_tbt.h  |   1 +
 2 files changed, 83 insertions(+), 47 deletions(-)
---
base-commit: 52ba76324a9d7c39830c850999210a36ef023cde
change-id: 20251006-topic-ps883x_usb4-32d4c3abaac1

Best regards,
-- 
Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

[PATCH 1/3] usb: typec: ps883x: Cache register settings, not Type-C mode

[Konrad Dybcio]

From: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

Certain Type-C mode configurations may result in identical settings of
the PS8830. Check if the latter have changed instead of assuming
there's always a difference.

ps883x_set() is changed to accept a typec_retimer_state in preparation
for more work and the ps883x_sw_set() (which only handles orientation
switching) is changed to use regmap_assign_bits(), which itself does
not perform any writes if the desired value is already set.

Reviewed-by: Jack Pham <jack.pham@oss.qualcomm.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
 drivers/usb/typec/mux/ps883x.c | 41 ++++++++++++++++++++++-------------------
 1 file changed, 22 insertions(+), 19 deletions(-)

diff --git a/drivers/usb/typec/mux/ps883x.c b/drivers/usb/typec/mux/ps883x.c
index ad59babf7cce..68f172df7be3 100644
--- a/drivers/usb/typec/mux/ps883x.c
+++ b/drivers/usb/typec/mux/ps883x.c
@@ -54,8 +54,9 @@ struct ps883x_retimer {
 	struct mutex lock; /* protect non-concurrent retimer & switch */
 
 	enum typec_orientation orientation;
-	unsigned long mode;
-	unsigned int svid;
+	u8 cfg0;
+	u8 cfg1;
+	u8 cfg2;
 };
 
 static int ps883x_configure(struct ps883x_retimer *retimer, int cfg0,
@@ -64,6 +65,9 @@ static int ps883x_configure(struct ps883x_retimer *retimer, int cfg0,
 	struct device *dev = &retimer->client->dev;
 	int ret;
 
+	if (retimer->cfg0 == cfg0 && retimer->cfg1 == cfg1 && retimer->cfg2 == cfg2)
+		return 0;
+
 	ret = regmap_write(retimer->regmap, REG_USB_PORT_CONN_STATUS_0, cfg0);
 	if (ret) {
 		dev_err(dev, "failed to write conn_status_0: %d\n", ret);
@@ -82,27 +86,31 @@ static int ps883x_configure(struct ps883x_retimer *retimer, int cfg0,
 		return ret;
 	}
 
+	retimer->cfg0 = cfg0;
+	retimer->cfg1 = cfg1;
+	retimer->cfg2 = cfg2;
+
 	return 0;
 }
 
-static int ps883x_set(struct ps883x_retimer *retimer)
+static int ps883x_set(struct ps883x_retimer *retimer, struct typec_retimer_state *state)
 {
 	int cfg0 = CONN_STATUS_0_CONNECTION_PRESENT;
 	int cfg1 = 0x00;
 	int cfg2 = 0x00;
 
 	if (retimer->orientation == TYPEC_ORIENTATION_NONE ||
-	    retimer->mode == TYPEC_STATE_SAFE) {
+	    state->mode == TYPEC_STATE_SAFE) {
 		return ps883x_configure(retimer, cfg0, cfg1, cfg2);
 	}
 
-	if (retimer->mode != TYPEC_STATE_USB && retimer->svid != USB_TYPEC_DP_SID)
+	if (state->alt && state->alt->svid != USB_TYPEC_DP_SID)
 		return -EINVAL;
 
 	if (retimer->orientation == TYPEC_ORIENTATION_REVERSE)
 		cfg0 |= CONN_STATUS_0_ORIENTATION_REVERSED;
 
-	switch (retimer->mode) {
+	switch (state->mode) {
 	case TYPEC_STATE_USB:
 		cfg0 |= CONN_STATUS_0_USB_3_1_CONNECTED;
 		break;
@@ -149,7 +157,13 @@ static int ps883x_sw_set(struct typec_switch_dev *sw,
 	if (retimer->orientation != orientation) {
 		retimer->orientation = orientation;
 
-		ret = ps883x_set(retimer);
+		ret = regmap_assign_bits(retimer->regmap, REG_USB_PORT_CONN_STATUS_0,
+					 CONN_STATUS_0_ORIENTATION_REVERSED,
+					 orientation == TYPEC_ORIENTATION_REVERSE);
+		if (ret) {
+			dev_err(&retimer->client->dev, "failed to set orientation: %d\n", ret);
+			return ret;
+		}
 	}
 
 	mutex_unlock(&retimer->lock);
@@ -165,18 +179,7 @@ static int ps883x_retimer_set(struct typec_retimer *rtmr,
 	int ret = 0;
 
 	mutex_lock(&retimer->lock);
-
-	if (state->mode != retimer->mode) {
-		retimer->mode = state->mode;
-
-		if (state->alt)
-			retimer->svid = state->alt->svid;
-		else
-			retimer->svid = 0;
-
-		ret = ps883x_set(retimer);
-	}
-
+	ret = ps883x_set(retimer, state);
 	mutex_unlock(&retimer->lock);
 
 	if (ret)

-- 
2.51.0

Re: [PATCH 1/3] usb: typec: ps883x: Cache register settings, not Type-C mode

[Heikki Krogerus]

On Tue, Oct 14, 2025 at 06:06:45PM +0200, Konrad Dybcio wrote:
> From: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
> 
> Certain Type-C mode configurations may result in identical settings of
> the PS8830. Check if the latter have changed instead of assuming
> there's always a difference.
> 
> ps883x_set() is changed to accept a typec_retimer_state in preparation
> for more work and the ps883x_sw_set() (which only handles orientation
> switching) is changed to use regmap_assign_bits(), which itself does
> not perform any writes if the desired value is already set.
> 
> Reviewed-by: Jack Pham <jack.pham@oss.qualcomm.com>
> Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>

> ---
>  drivers/usb/typec/mux/ps883x.c | 41 ++++++++++++++++++++++-------------------
>  1 file changed, 22 insertions(+), 19 deletions(-)
> 
> diff --git a/drivers/usb/typec/mux/ps883x.c b/drivers/usb/typec/mux/ps883x.c
> index ad59babf7cce..68f172df7be3 100644
> --- a/drivers/usb/typec/mux/ps883x.c
> +++ b/drivers/usb/typec/mux/ps883x.c
> @@ -54,8 +54,9 @@ struct ps883x_retimer {
>  	struct mutex lock; /* protect non-concurrent retimer & switch */
>  
>  	enum typec_orientation orientation;
> -	unsigned long mode;
> -	unsigned int svid;
> +	u8 cfg0;
> +	u8 cfg1;
> +	u8 cfg2;
>  };
>  
>  static int ps883x_configure(struct ps883x_retimer *retimer, int cfg0,
> @@ -64,6 +65,9 @@ static int ps883x_configure(struct ps883x_retimer *retimer, int cfg0,
>  	struct device *dev = &retimer->client->dev;
>  	int ret;
>  
> +	if (retimer->cfg0 == cfg0 && retimer->cfg1 == cfg1 && retimer->cfg2 == cfg2)
> +		return 0;
> +
>  	ret = regmap_write(retimer->regmap, REG_USB_PORT_CONN_STATUS_0, cfg0);
>  	if (ret) {
>  		dev_err(dev, "failed to write conn_status_0: %d\n", ret);
> @@ -82,27 +86,31 @@ static int ps883x_configure(struct ps883x_retimer *retimer, int cfg0,
>  		return ret;
>  	}
>  
> +	retimer->cfg0 = cfg0;
> +	retimer->cfg1 = cfg1;
> +	retimer->cfg2 = cfg2;
> +
>  	return 0;
>  }
>  
> -static int ps883x_set(struct ps883x_retimer *retimer)
> +static int ps883x_set(struct ps883x_retimer *retimer, struct typec_retimer_state *state)
>  {
>  	int cfg0 = CONN_STATUS_0_CONNECTION_PRESENT;
>  	int cfg1 = 0x00;
>  	int cfg2 = 0x00;
>  
>  	if (retimer->orientation == TYPEC_ORIENTATION_NONE ||
> -	    retimer->mode == TYPEC_STATE_SAFE) {
> +	    state->mode == TYPEC_STATE_SAFE) {
>  		return ps883x_configure(retimer, cfg0, cfg1, cfg2);
>  	}
>  
> -	if (retimer->mode != TYPEC_STATE_USB && retimer->svid != USB_TYPEC_DP_SID)
> +	if (state->alt && state->alt->svid != USB_TYPEC_DP_SID)
>  		return -EINVAL;
>  
>  	if (retimer->orientation == TYPEC_ORIENTATION_REVERSE)
>  		cfg0 |= CONN_STATUS_0_ORIENTATION_REVERSED;
>  
> -	switch (retimer->mode) {
> +	switch (state->mode) {
>  	case TYPEC_STATE_USB:
>  		cfg0 |= CONN_STATUS_0_USB_3_1_CONNECTED;
>  		break;
> @@ -149,7 +157,13 @@ static int ps883x_sw_set(struct typec_switch_dev *sw,
>  	if (retimer->orientation != orientation) {
>  		retimer->orientation = orientation;
>  
> -		ret = ps883x_set(retimer);
> +		ret = regmap_assign_bits(retimer->regmap, REG_USB_PORT_CONN_STATUS_0,
> +					 CONN_STATUS_0_ORIENTATION_REVERSED,
> +					 orientation == TYPEC_ORIENTATION_REVERSE);
> +		if (ret) {
> +			dev_err(&retimer->client->dev, "failed to set orientation: %d\n", ret);
> +			return ret;
> +		}
>  	}
>  
>  	mutex_unlock(&retimer->lock);
> @@ -165,18 +179,7 @@ static int ps883x_retimer_set(struct typec_retimer *rtmr,
>  	int ret = 0;
>  
>  	mutex_lock(&retimer->lock);
> -
> -	if (state->mode != retimer->mode) {
> -		retimer->mode = state->mode;
> -
> -		if (state->alt)
> -			retimer->svid = state->alt->svid;
> -		else
> -			retimer->svid = 0;
> -
> -		ret = ps883x_set(retimer);
> -	}
> -
> +	ret = ps883x_set(retimer, state);
>  	mutex_unlock(&retimer->lock);
>  
>  	if (ret)
> 
> -- 
> 2.51.0

-- 
heikki

[PATCH 2/3] usb: typec: ps883x: Rework ps883x_set()

[Konrad Dybcio]

From: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

In preparation to extend it with new alt/USB modes, rework the code a
bit by changing the flow into a pair of switch statements.

Reviewed-by: Jack Pham <jack.pham@oss.qualcomm.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
 drivers/usb/typec/mux/ps883x.c | 71 ++++++++++++++++++++++--------------------
 1 file changed, 37 insertions(+), 34 deletions(-)

diff --git a/drivers/usb/typec/mux/ps883x.c b/drivers/usb/typec/mux/ps883x.c
index 68f172df7be3..72f1e737ca4b 100644
--- a/drivers/usb/typec/mux/ps883x.c
+++ b/drivers/usb/typec/mux/ps883x.c
@@ -99,44 +99,47 @@ static int ps883x_set(struct ps883x_retimer *retimer, struct typec_retimer_state
 	int cfg1 = 0x00;
 	int cfg2 = 0x00;
 
-	if (retimer->orientation == TYPEC_ORIENTATION_NONE ||
-	    state->mode == TYPEC_STATE_SAFE) {
-		return ps883x_configure(retimer, cfg0, cfg1, cfg2);
-	}
-
-	if (state->alt && state->alt->svid != USB_TYPEC_DP_SID)
-		return -EINVAL;
-
 	if (retimer->orientation == TYPEC_ORIENTATION_REVERSE)
 		cfg0 |= CONN_STATUS_0_ORIENTATION_REVERSED;
 
-	switch (state->mode) {
-	case TYPEC_STATE_USB:
-		cfg0 |= CONN_STATUS_0_USB_3_1_CONNECTED;
-		break;
+	if (state->alt) {
+		switch (state->alt->svid) {
+		case USB_TYPEC_DP_SID:
+			cfg1 |= CONN_STATUS_1_DP_CONNECTED |
+				CONN_STATUS_1_DP_HPD_LEVEL;
 
-	case TYPEC_DP_STATE_C:
-		cfg1 = CONN_STATUS_1_DP_CONNECTED |
-		       CONN_STATUS_1_DP_SINK_REQUESTED |
-		       CONN_STATUS_1_DP_PIN_ASSIGNMENT_C_D |
-		       CONN_STATUS_1_DP_HPD_LEVEL;
-		break;
-
-	case TYPEC_DP_STATE_D:
-		cfg0 |= CONN_STATUS_0_USB_3_1_CONNECTED;
-		cfg1 = CONN_STATUS_1_DP_CONNECTED |
-		       CONN_STATUS_1_DP_SINK_REQUESTED |
-		       CONN_STATUS_1_DP_PIN_ASSIGNMENT_C_D |
-		       CONN_STATUS_1_DP_HPD_LEVEL;
-		break;
-
-	case TYPEC_DP_STATE_E:
-		cfg1 = CONN_STATUS_1_DP_CONNECTED |
-		       CONN_STATUS_1_DP_HPD_LEVEL;
-		break;
-
-	default:
-		return -EOPNOTSUPP;
+			switch (state->mode)  {
+			case TYPEC_DP_STATE_C:
+				cfg1 |= CONN_STATUS_1_DP_SINK_REQUESTED |
+					CONN_STATUS_1_DP_PIN_ASSIGNMENT_C_D;
+				fallthrough;
+			case TYPEC_DP_STATE_D:
+				cfg1 |= CONN_STATUS_0_USB_3_1_CONNECTED;
+				break;
+			default: /* MODE_E */
+				break;
+			}
+			break;
+		default:
+			dev_err(&retimer->client->dev, "Got unsupported SID: 0x%x\n",
+				state->alt->svid);
+			return -EOPNOTSUPP;
+		}
+	} else {
+		switch (state->mode) {
+		case TYPEC_STATE_SAFE:
+		/* USB2 pins don't even go through this chip */
+		case TYPEC_MODE_USB2:
+			break;
+		case TYPEC_STATE_USB:
+		case TYPEC_MODE_USB3:
+			cfg0 |= CONN_STATUS_0_USB_3_1_CONNECTED;
+			break;
+		default:
+			dev_err(&retimer->client->dev, "Got unsupported mode: %lu\n",
+				state->mode);
+			return -EOPNOTSUPP;
+		}
 	}
 
 	return ps883x_configure(retimer, cfg0, cfg1, cfg2);

-- 
2.51.0

Re: [PATCH 2/3] usb: typec: ps883x: Rework ps883x_set()

[Heikki Krogerus]

On Tue, Oct 14, 2025 at 06:06:46PM +0200, Konrad Dybcio wrote:
> From: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
> 
> In preparation to extend it with new alt/USB modes, rework the code a
> bit by changing the flow into a pair of switch statements.
> 
> Reviewed-by: Jack Pham <jack.pham@oss.qualcomm.com>
> Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>

> ---
>  drivers/usb/typec/mux/ps883x.c | 71 ++++++++++++++++++++++--------------------
>  1 file changed, 37 insertions(+), 34 deletions(-)
> 
> diff --git a/drivers/usb/typec/mux/ps883x.c b/drivers/usb/typec/mux/ps883x.c
> index 68f172df7be3..72f1e737ca4b 100644
> --- a/drivers/usb/typec/mux/ps883x.c
> +++ b/drivers/usb/typec/mux/ps883x.c
> @@ -99,44 +99,47 @@ static int ps883x_set(struct ps883x_retimer *retimer, struct typec_retimer_state
>  	int cfg1 = 0x00;
>  	int cfg2 = 0x00;
>  
> -	if (retimer->orientation == TYPEC_ORIENTATION_NONE ||
> -	    state->mode == TYPEC_STATE_SAFE) {
> -		return ps883x_configure(retimer, cfg0, cfg1, cfg2);
> -	}
> -
> -	if (state->alt && state->alt->svid != USB_TYPEC_DP_SID)
> -		return -EINVAL;
> -
>  	if (retimer->orientation == TYPEC_ORIENTATION_REVERSE)
>  		cfg0 |= CONN_STATUS_0_ORIENTATION_REVERSED;
>  
> -	switch (state->mode) {
> -	case TYPEC_STATE_USB:
> -		cfg0 |= CONN_STATUS_0_USB_3_1_CONNECTED;
> -		break;
> +	if (state->alt) {
> +		switch (state->alt->svid) {
> +		case USB_TYPEC_DP_SID:
> +			cfg1 |= CONN_STATUS_1_DP_CONNECTED |
> +				CONN_STATUS_1_DP_HPD_LEVEL;
>  
> -	case TYPEC_DP_STATE_C:
> -		cfg1 = CONN_STATUS_1_DP_CONNECTED |
> -		       CONN_STATUS_1_DP_SINK_REQUESTED |
> -		       CONN_STATUS_1_DP_PIN_ASSIGNMENT_C_D |
> -		       CONN_STATUS_1_DP_HPD_LEVEL;
> -		break;
> -
> -	case TYPEC_DP_STATE_D:
> -		cfg0 |= CONN_STATUS_0_USB_3_1_CONNECTED;
> -		cfg1 = CONN_STATUS_1_DP_CONNECTED |
> -		       CONN_STATUS_1_DP_SINK_REQUESTED |
> -		       CONN_STATUS_1_DP_PIN_ASSIGNMENT_C_D |
> -		       CONN_STATUS_1_DP_HPD_LEVEL;
> -		break;
> -
> -	case TYPEC_DP_STATE_E:
> -		cfg1 = CONN_STATUS_1_DP_CONNECTED |
> -		       CONN_STATUS_1_DP_HPD_LEVEL;
> -		break;
> -
> -	default:
> -		return -EOPNOTSUPP;
> +			switch (state->mode)  {
> +			case TYPEC_DP_STATE_C:
> +				cfg1 |= CONN_STATUS_1_DP_SINK_REQUESTED |
> +					CONN_STATUS_1_DP_PIN_ASSIGNMENT_C_D;
> +				fallthrough;
> +			case TYPEC_DP_STATE_D:
> +				cfg1 |= CONN_STATUS_0_USB_3_1_CONNECTED;
> +				break;
> +			default: /* MODE_E */
> +				break;
> +			}
> +			break;
> +		default:
> +			dev_err(&retimer->client->dev, "Got unsupported SID: 0x%x\n",
> +				state->alt->svid);
> +			return -EOPNOTSUPP;
> +		}
> +	} else {
> +		switch (state->mode) {
> +		case TYPEC_STATE_SAFE:
> +		/* USB2 pins don't even go through this chip */
> +		case TYPEC_MODE_USB2:
> +			break;
> +		case TYPEC_STATE_USB:
> +		case TYPEC_MODE_USB3:
> +			cfg0 |= CONN_STATUS_0_USB_3_1_CONNECTED;
> +			break;
> +		default:
> +			dev_err(&retimer->client->dev, "Got unsupported mode: %lu\n",
> +				state->mode);
> +			return -EOPNOTSUPP;
> +		}
>  	}
>  
>  	return ps883x_configure(retimer, cfg0, cfg1, cfg2);
> 
> -- 
> 2.51.0

-- 
heikki

[PATCH 3/3] usb: typec: ps883x: Add USB4 mode and TBT3 altmode support

[Konrad Dybcio]

From: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

This chip can do some more than the driver currently describes. Add
support for configuring it for various flavors of TBT3/USB4 operation.

Reviewed-by: Jack Pham <jack.pham@oss.qualcomm.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
 drivers/usb/typec/mux/ps883x.c | 29 +++++++++++++++++++++++++++++
 include/linux/usb/typec_tbt.h  |  1 +
 2 files changed, 30 insertions(+)

diff --git a/drivers/usb/typec/mux/ps883x.c b/drivers/usb/typec/mux/ps883x.c
index 72f1e737ca4b..7c61629b36d6 100644
--- a/drivers/usb/typec/mux/ps883x.c
+++ b/drivers/usb/typec/mux/ps883x.c
@@ -14,15 +14,18 @@
 #include <linux/mutex.h>
 #include <linux/regmap.h>
 #include <linux/regulator/consumer.h>
+#include <linux/usb/pd.h>
 #include <linux/usb/typec_altmode.h>
 #include <linux/usb/typec_dp.h>
 #include <linux/usb/typec_mux.h>
 #include <linux/usb/typec_retimer.h>
+#include <linux/usb/typec_tbt.h>
 
 #define REG_USB_PORT_CONN_STATUS_0		0x00
 
 #define CONN_STATUS_0_CONNECTION_PRESENT	BIT(0)
 #define CONN_STATUS_0_ORIENTATION_REVERSED	BIT(1)
+#define CONN_STATUS_0_ACTIVE_CABLE		BIT(2)
 #define CONN_STATUS_0_USB_3_1_CONNECTED		BIT(5)
 
 #define REG_USB_PORT_CONN_STATUS_1		0x01
@@ -34,6 +37,10 @@
 
 #define REG_USB_PORT_CONN_STATUS_2		0x02
 
+#define CONN_STATUS_2_TBT_CONNECTED		BIT(0)
+#define CONN_STATUS_2_TBT_UNIDIR_LSRX_ACT_LT	BIT(4)
+#define CONN_STATUS_2_USB4_CONNECTED		BIT(7)
+
 struct ps883x_retimer {
 	struct i2c_client *client;
 	struct gpio_desc *reset_gpio;
@@ -95,6 +102,8 @@ static int ps883x_configure(struct ps883x_retimer *retimer, int cfg0,
 
 static int ps883x_set(struct ps883x_retimer *retimer, struct typec_retimer_state *state)
 {
+	struct typec_thunderbolt_data *tb_data;
+	const struct enter_usb_data *eudo_data;
 	int cfg0 = CONN_STATUS_0_CONNECTION_PRESENT;
 	int cfg1 = 0x00;
 	int cfg2 = 0x00;
@@ -120,6 +129,18 @@ static int ps883x_set(struct ps883x_retimer *retimer, struct typec_retimer_state
 				break;
 			}
 			break;
+		case USB_TYPEC_TBT_SID:
+			tb_data = state->data;
+
+			/* Unconditional */
+			cfg2 |= CONN_STATUS_2_TBT_CONNECTED;
+
+			if (tb_data->cable_mode & TBT_CABLE_ACTIVE_PASSIVE)
+				cfg0 |= CONN_STATUS_0_ACTIVE_CABLE;
+
+			if (tb_data->enter_vdo & TBT_ENTER_MODE_UNI_DIR_LSRX)
+				cfg2 |= CONN_STATUS_2_TBT_UNIDIR_LSRX_ACT_LT;
+			break;
 		default:
 			dev_err(&retimer->client->dev, "Got unsupported SID: 0x%x\n",
 				state->alt->svid);
@@ -135,6 +156,14 @@ static int ps883x_set(struct ps883x_retimer *retimer, struct typec_retimer_state
 		case TYPEC_MODE_USB3:
 			cfg0 |= CONN_STATUS_0_USB_3_1_CONNECTED;
 			break;
+		case TYPEC_MODE_USB4:
+			eudo_data = state->data;
+
+			cfg2 |= CONN_STATUS_2_USB4_CONNECTED;
+
+			if (FIELD_GET(EUDO_CABLE_TYPE_MASK, eudo_data->eudo) != EUDO_CABLE_TYPE_PASSIVE)
+				cfg0 |= CONN_STATUS_0_ACTIVE_CABLE;
+			break;
 		default:
 			dev_err(&retimer->client->dev, "Got unsupported mode: %lu\n",
 				state->mode);
diff --git a/include/linux/usb/typec_tbt.h b/include/linux/usb/typec_tbt.h
index 55dcea12082c..0b570f1b8bc8 100644
--- a/include/linux/usb/typec_tbt.h
+++ b/include/linux/usb/typec_tbt.h
@@ -55,6 +55,7 @@ struct typec_thunderbolt_data {
 
 /* TBT3 Device Enter Mode VDO bits */
 #define TBT_ENTER_MODE_CABLE_SPEED(s)	TBT_SET_CABLE_SPEED(s)
+#define TBT_ENTER_MODE_UNI_DIR_LSRX	BIT(23)
 #define TBT_ENTER_MODE_ACTIVE_CABLE	BIT(24)
 
 #endif /* __USB_TYPEC_TBT_H */

-- 
2.51.0

Re: [PATCH 3/3] usb: typec: ps883x: Add USB4 mode and TBT3 altmode support

[Heikki Krogerus]

On Tue, Oct 14, 2025 at 06:06:47PM +0200, Konrad Dybcio wrote:
> From: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
> 
> This chip can do some more than the driver currently describes. Add
> support for configuring it for various flavors of TBT3/USB4 operation.
> 
> Reviewed-by: Jack Pham <jack.pham@oss.qualcomm.com>
> Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>

> ---
>  drivers/usb/typec/mux/ps883x.c | 29 +++++++++++++++++++++++++++++
>  include/linux/usb/typec_tbt.h  |  1 +
>  2 files changed, 30 insertions(+)
> 
> diff --git a/drivers/usb/typec/mux/ps883x.c b/drivers/usb/typec/mux/ps883x.c
> index 72f1e737ca4b..7c61629b36d6 100644
> --- a/drivers/usb/typec/mux/ps883x.c
> +++ b/drivers/usb/typec/mux/ps883x.c
> @@ -14,15 +14,18 @@
>  #include <linux/mutex.h>
>  #include <linux/regmap.h>
>  #include <linux/regulator/consumer.h>
> +#include <linux/usb/pd.h>
>  #include <linux/usb/typec_altmode.h>
>  #include <linux/usb/typec_dp.h>
>  #include <linux/usb/typec_mux.h>
>  #include <linux/usb/typec_retimer.h>
> +#include <linux/usb/typec_tbt.h>
>  
>  #define REG_USB_PORT_CONN_STATUS_0		0x00
>  
>  #define CONN_STATUS_0_CONNECTION_PRESENT	BIT(0)
>  #define CONN_STATUS_0_ORIENTATION_REVERSED	BIT(1)
> +#define CONN_STATUS_0_ACTIVE_CABLE		BIT(2)
>  #define CONN_STATUS_0_USB_3_1_CONNECTED		BIT(5)
>  
>  #define REG_USB_PORT_CONN_STATUS_1		0x01
> @@ -34,6 +37,10 @@
>  
>  #define REG_USB_PORT_CONN_STATUS_2		0x02
>  
> +#define CONN_STATUS_2_TBT_CONNECTED		BIT(0)
> +#define CONN_STATUS_2_TBT_UNIDIR_LSRX_ACT_LT	BIT(4)
> +#define CONN_STATUS_2_USB4_CONNECTED		BIT(7)
> +
>  struct ps883x_retimer {
>  	struct i2c_client *client;
>  	struct gpio_desc *reset_gpio;
> @@ -95,6 +102,8 @@ static int ps883x_configure(struct ps883x_retimer *retimer, int cfg0,
>  
>  static int ps883x_set(struct ps883x_retimer *retimer, struct typec_retimer_state *state)
>  {
> +	struct typec_thunderbolt_data *tb_data;
> +	const struct enter_usb_data *eudo_data;
>  	int cfg0 = CONN_STATUS_0_CONNECTION_PRESENT;
>  	int cfg1 = 0x00;
>  	int cfg2 = 0x00;
> @@ -120,6 +129,18 @@ static int ps883x_set(struct ps883x_retimer *retimer, struct typec_retimer_state
>  				break;
>  			}
>  			break;
> +		case USB_TYPEC_TBT_SID:
> +			tb_data = state->data;
> +
> +			/* Unconditional */
> +			cfg2 |= CONN_STATUS_2_TBT_CONNECTED;
> +
> +			if (tb_data->cable_mode & TBT_CABLE_ACTIVE_PASSIVE)
> +				cfg0 |= CONN_STATUS_0_ACTIVE_CABLE;
> +
> +			if (tb_data->enter_vdo & TBT_ENTER_MODE_UNI_DIR_LSRX)
> +				cfg2 |= CONN_STATUS_2_TBT_UNIDIR_LSRX_ACT_LT;
> +			break;
>  		default:
>  			dev_err(&retimer->client->dev, "Got unsupported SID: 0x%x\n",
>  				state->alt->svid);
> @@ -135,6 +156,14 @@ static int ps883x_set(struct ps883x_retimer *retimer, struct typec_retimer_state
>  		case TYPEC_MODE_USB3:
>  			cfg0 |= CONN_STATUS_0_USB_3_1_CONNECTED;
>  			break;
> +		case TYPEC_MODE_USB4:
> +			eudo_data = state->data;
> +
> +			cfg2 |= CONN_STATUS_2_USB4_CONNECTED;
> +
> +			if (FIELD_GET(EUDO_CABLE_TYPE_MASK, eudo_data->eudo) != EUDO_CABLE_TYPE_PASSIVE)
> +				cfg0 |= CONN_STATUS_0_ACTIVE_CABLE;
> +			break;
>  		default:
>  			dev_err(&retimer->client->dev, "Got unsupported mode: %lu\n",
>  				state->mode);
> diff --git a/include/linux/usb/typec_tbt.h b/include/linux/usb/typec_tbt.h
> index 55dcea12082c..0b570f1b8bc8 100644
> --- a/include/linux/usb/typec_tbt.h
> +++ b/include/linux/usb/typec_tbt.h
> @@ -55,6 +55,7 @@ struct typec_thunderbolt_data {
>  
>  /* TBT3 Device Enter Mode VDO bits */
>  #define TBT_ENTER_MODE_CABLE_SPEED(s)	TBT_SET_CABLE_SPEED(s)
> +#define TBT_ENTER_MODE_UNI_DIR_LSRX	BIT(23)
>  #define TBT_ENTER_MODE_ACTIVE_CABLE	BIT(24)
>  
>  #endif /* __USB_TYPEC_TBT_H */
> 
> -- 
> 2.51.0

-- 
heikki