* [PATCH] USB: serial: option: add Telit FN920C04 ECM compositions
@ 2025-10-23 3:44 LI Qingwu
2025-10-23 12:12 ` Johan Hovold
0 siblings, 1 reply; 2+ messages in thread
From: LI Qingwu @ 2025-10-23 3:44 UTC (permalink / raw)
To: johan, Qing-wu.Li; +Cc: gregkh, linux-usb, linux-kernel
Add support for the Telit Cinterion FN920C04 module when operating in
ECM (Ethernet Control Model) mode. The following USB product IDs are
used by the module when AT#USBCFG is set to 3 or 7.
0x10A3: ECM + tty (NMEA) + tty (DUN) [+ tty (DIAG)]
T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10a3 Rev= 5.15
S: Manufacturer=Telit Cinterion
S: Product=FN920
S: SerialNumber=76e7cb38
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=82(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=60 Driver=option
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
0x10A8: ECM + tty (DUN) + tty (AUX) [+ tty (DIAG)]
T: Bus=03 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1bc7 ProdID=10a8 Rev= 5.15
S: Manufacturer=Telit Cinterion
S: Product=FN920
S: SerialNumber=76e7cb38
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E: Ad=82(I) Atr=03(Int.) MxPS= 16 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=84(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Adding these IDs allows the option driver to automatically create the
corresponding /dev/ttyUSB* ports under ECM mode.
Tested with FN920C04 under ECM configuration (USBCFG=3 and 7).
Signed-off-by: LI Qingwu <Qing-wu.Li@leica-geosystems.com.cn>
---
drivers/usb/serial/option.c | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index 27879cc57536..293e3e25e65d 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -1381,10 +1381,14 @@ static const struct usb_device_id option_ids[] = {
.driver_info = RSVD(0) | NCTRL(3) },
{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10a2, 0xff), /* Telit FN920C04 (MBIM) */
.driver_info = NCTRL(4) },
+ { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10a3, 0xff), /* Telit FN920C04 (ECM) */
+ .driver_info = NCTRL(4) },
{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10a4, 0xff), /* Telit FN20C04 (rmnet) */
.driver_info = RSVD(0) | NCTRL(3) },
{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10a7, 0xff), /* Telit FN920C04 (MBIM) */
.driver_info = NCTRL(4) },
+ { USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10a8, 0xff), /* Telit FN920C04 (ECM) */
+ .driver_info = NCTRL(4) },
{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10a9, 0xff), /* Telit FN20C04 (rmnet) */
.driver_info = RSVD(0) | NCTRL(2) | RSVD(3) | RSVD(4) },
{ USB_DEVICE_INTERFACE_CLASS(TELIT_VENDOR_ID, 0x10aa, 0xff), /* Telit FN920C04 (MBIM) */
--
2.43.0
^ permalink raw reply related [flat|nested] 2+ messages in thread
* Re: [PATCH] USB: serial: option: add Telit FN920C04 ECM compositions
2025-10-23 3:44 [PATCH] USB: serial: option: add Telit FN920C04 ECM compositions LI Qingwu
@ 2025-10-23 12:12 ` Johan Hovold
0 siblings, 0 replies; 2+ messages in thread
From: Johan Hovold @ 2025-10-23 12:12 UTC (permalink / raw)
To: LI Qingwu; +Cc: gregkh, linux-usb, linux-kernel
On Thu, Oct 23, 2025 at 03:44:22AM +0000, LI Qingwu wrote:
> Add support for the Telit Cinterion FN920C04 module when operating in
> ECM (Ethernet Control Model) mode. The following USB product IDs are
> used by the module when AT#USBCFG is set to 3 or 7.
Applied, thanks.
Johan
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2025-10-23 12:12 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2025-10-23 3:44 [PATCH] USB: serial: option: add Telit FN920C04 ECM compositions LI Qingwu
2025-10-23 12:12 ` Johan Hovold
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).