Re: [PATCH 3/3] usb: dwc3: xilinx: fix error handling in zynqmp init error paths

[Thinh Nguyen <Thinh.Nguyen@synopsys.com>]

On Thu, May 14, 2026, Pandey, Radhey Shyam wrote:
> On 5/14/2026 7:13 AM, Thinh Nguyen wrote:
> > On Mon, May 11, 2026, Radhey Shyam Pandey wrote:
> > > Fix error handling and resource cleanup i.e remove invalid
> > > phy_exit() after failed phy_init(), route failures through
> > > proper cleanup paths and return 0 explicitly on success.
> > > 
> > > Fixes: 84770f028fab ("usb: dwc3: Add driver for Xilinx platforms")
> > > Cc: stable@vger.kernel.org
> > > Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
> > > ---
> > >   drivers/usb/dwc3/dwc3-xilinx.c | 27 +++++++++++++++------------
> > >   1 file changed, 15 insertions(+), 12 deletions(-)
> > > 
> > > diff --git a/drivers/usb/dwc3/dwc3-xilinx.c b/drivers/usb/dwc3/dwc3-xilinx.c
> > > index 94458b3da1a0..b832505e1b04 100644
> > > --- a/drivers/usb/dwc3/dwc3-xilinx.c
> > > +++ b/drivers/usb/dwc3/dwc3-xilinx.c
> > > @@ -176,15 +176,13 @@ static int dwc3_xlnx_init_zynqmp(struct dwc3_xlnx *priv_data)
> > >   	}
> > >   	ret = phy_init(priv_data->usb3_phy);
> > > -	if (ret < 0) {
> > > -		phy_exit(priv_data->usb3_phy);
> > > +	if (ret < 0)
> > >   		goto err;
> > > -	}
> > >   	ret = reset_control_deassert(apbrst);
> > >   	if (ret < 0) {
> > >   		dev_err(dev, "Failed to release APB reset\n");
> > > -		goto err;
> > > +		goto err_phy_exit;
> > >   	}
> > >   	if (priv_data->usb3_phy) {
> > > @@ -200,26 +198,24 @@ static int dwc3_xlnx_init_zynqmp(struct dwc3_xlnx *priv_data)
> > >   	ret = reset_control_deassert(crst);
> > >   	if (ret < 0) {
> > >   		dev_err(dev, "Failed to release core reset\n");
> > > -		goto err;
> > > +		goto err_phy_exit;
> > >   	}
> > >   	ret = reset_control_deassert(hibrst);
> > >   	if (ret < 0) {
> > >   		dev_err(dev, "Failed to release hibernation reset\n");
> > > -		goto err;
> > > +		goto err_phy_exit;
> > >   	}
> > >   	ret = phy_power_on(priv_data->usb3_phy);
> > > -	if (ret < 0) {
> > > -		phy_exit(priv_data->usb3_phy);
> > > -		goto err;
> > > -	}
> > > +	if (ret < 0)
> > > +		goto err_phy_exit;
> > >   	/* ulpi reset via gpio-modepin or gpio-framework driver */
> > >   	reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
> > >   	if (IS_ERR(reset_gpio)) {
> > > -		return dev_err_probe(dev, PTR_ERR(reset_gpio),
> > > -				     "Failed to request reset GPIO\n");
> > > +		ret = PTR_ERR(reset_gpio);
> > > +		goto err_phy_power_off;
> > >   	}
> > >   	if (reset_gpio) {
> > > @@ -229,6 +225,13 @@ static int dwc3_xlnx_init_zynqmp(struct dwc3_xlnx *priv_data)
> > >   	}
> > >   	dwc3_xlnx_set_coherency(priv_data, XLNX_USB_TRAFFIC_ROUTE_CONFIG);
> > > +
> > > +	return 0;
> > > +
> > > +err_phy_power_off:
> > > +	phy_power_off(priv_data->usb3_phy);
> > > +err_phy_exit:
> > > +	phy_exit(priv_data->usb3_phy);
> > >   err:
> > >   	return ret;
> > >   }
> > > -- 
> > > 2.44.4
> > > 
> > 
> > This fix should be a separate patch from this cleanup series.
> > 
> 
> Sure, will split it into a separate patch. Does this patch look fine?
> If so i can add the Reviewed-by tag in v2 or address any further
> comments if needed.
> 

This patch looks good. You can add my Acked-by when resubmit:

Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>

Thanks,
Thinh