From: Tejas Joglekar <Tejas.Joglekar@synopsys.com>
To: Felipe Balbi <balbi@kernel.org>,
Tejas Joglekar <Tejas.Joglekar@synopsys.com>,
linux-usb@vger.kernel.org, devicetree@vger.kernel.org,
Rob Herring <robh+dt@kernel.org>,
Chunfeng Yun <chunfeng.yun@mediatek.com>,
Fredrik Noring <noring@nocrew.org>,
Mathias Nyman <mathias.nyman@intel.com>,
Mark Rutland <mark.rutland@arm.com>,
Sebastian Andrzej Siewior <bigeasy@linutronix.de>,
Raul E Rangel <rrangel@chromium.org>,
Laurentiu Tudor <laurentiu.tudor@nxp.com>,
Marek Szyprowski <m.szyprowski@samsung.com>
Cc: John Youn <John.Youn@synopsys.com>
Subject: [RESENDING RFC PATCH 0/4] Add logic to consolidate TRBs for Synopsys xHC
Date: Fri, 27 Mar 2020 14:22:23 +0530 [thread overview]
Message-ID: <cover.1585297723.git.joglekar@synopsys.com> (raw)
The Synopsys xHC has an internal TRB cache of size TRB_CACHE_SIZE for
each endpoint. The default value for TRB_CACHE_SIZE is 16 for SS and 8
for HS. The controller loads and updates the TRB cache from the
transfer ring in system memory whenever the driver issues a start
transfer or update transfer command.
For chained TRBs, the Synopsys xHC requires that the total amount of
bytes for all TRBs loaded in the TRB cache be greater than or equal to
1 MPS. Or the chain ends within the TRB cache (with a last TRB).
If this requirement is not met, the controller will not be able to
send or receive a packet and it will hang causing a driver timeout and
error.
This patch set adds logic to the XHCI driver to detect and prevent this
from happening along with the quirk to enable this logic for Synopsys
HAPS platform.
Based on Mathias's feedback on previous implementation where consolidation
was done in TRB cache, with this patch series the implementation is done
during mapping of the URB by consolidating the SG list into a temporary
buffer if the SG list buffer sizes within TRB_CACHE_SIZE is less than MPS.
Tejas Joglekar (4):
dt-bindings: usb: Add snps,consolidate-sgl & consolidate-sgl
usb: xhci: Set quirk for XHCI_CONSOLIDATE_SG_LIST
usb: dwc3: Add device property consolidate-sgl
usb: xhci: Use temporary buffer to consolidate SG
Resending as 'umlaut' is not accepted by some servers in email.
Documentation/devicetree/bindings/usb/dwc3.txt | 3 +
Documentation/devicetree/bindings/usb/usb-xhci.txt | 3 +
drivers/usb/core/hcd.c | 8 ++
drivers/usb/dwc3/core.c | 2 +
drivers/usb/dwc3/core.h | 2 +
drivers/usb/dwc3/dwc3-haps.c | 1 +
drivers/usb/dwc3/host.c | 5 +-
drivers/usb/host/xhci-pci.c | 3 +
drivers/usb/host/xhci-plat.c | 3 +
drivers/usb/host/xhci-ring.c | 2 +-
drivers/usb/host/xhci.c | 128 +++++++++++++++++++++
drivers/usb/host/xhci.h | 5 +
12 files changed, 163 insertions(+), 2 deletions(-)
--
2.11.0
next reply other threads:[~2020-03-27 8:52 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-03-27 8:52 Tejas Joglekar [this message]
2020-03-27 8:34 ` [RFC PATCH 1/4] dt-bindings: usb: Add snps,consolidate-sgl & consolidate-sgl Tejas Joglekar
2020-03-27 9:41 ` [RESENDING RFC " Tejas Joglekar
2020-03-27 9:54 ` Greg KH
2020-03-27 10:11 ` Tejas Joglekar
2020-03-27 10:24 ` Greg KH
2020-03-27 10:28 ` Tejas Joglekar
2020-04-05 1:45 ` Rob Herring
2020-04-14 10:09 ` Tejas Joglekar
2020-04-16 8:22 ` Felipe Balbi
2020-04-16 16:37 ` Tejas Joglekar
2020-04-17 11:44 ` Mathias Nyman
2020-03-27 8:35 ` [RFC PATCH 2/4] usb: xhci: Set quirk for XHCI_CONSOLIDATE_SG_LIST Tejas Joglekar
2020-03-27 9:42 ` [RESENDING RFC " Tejas Joglekar
2020-03-27 8:35 ` [RFC PATCH 3/4] usb: dwc3: Add device property consolidate-sgl Tejas Joglekar
2020-03-27 9:42 ` [RESENDING RFC " Tejas Joglekar
2020-03-27 8:53 ` [RESENDING RFC PATCH 4/4] usb: xhci: Use temporary buffer to consolidate SG Tejas Joglekar
2020-03-27 9:27 ` Greg KH
2020-03-27 10:05 ` Tejas Joglekar
2020-03-27 10:22 ` Greg KH
2020-03-27 11:25 ` Mathias Nyman
2020-03-27 15:38 ` Raul Rangel
2020-03-27 9:28 ` [RESENDING RFC PATCH 0/4] Add logic to consolidate TRBs for Synopsys xHC Greg KH
2020-03-27 9:43 ` Tejas Joglekar
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=cover.1585297723.git.joglekar@synopsys.com \
--to=tejas.joglekar@synopsys.com \
--cc=John.Youn@synopsys.com \
--cc=balbi@kernel.org \
--cc=bigeasy@linutronix.de \
--cc=chunfeng.yun@mediatek.com \
--cc=devicetree@vger.kernel.org \
--cc=laurentiu.tudor@nxp.com \
--cc=linux-usb@vger.kernel.org \
--cc=m.szyprowski@samsung.com \
--cc=mark.rutland@arm.com \
--cc=mathias.nyman@intel.com \
--cc=noring@nocrew.org \
--cc=robh+dt@kernel.org \
--cc=rrangel@chromium.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).