Re: [RFC v4 2/5] usb: dwc3: core: Refactor PHY logic to support Multiport Controller

[Krishna Kurapati PSSNV <quic_kriskura@quicinc.com>]

On 1/21/2023 4:27 AM, Thinh Nguyen wrote:
> On Thu, Jan 19, 2023, Thinh Nguyen wrote:
>> Hi,
>>
>> On Sun, Jan 15, 2023, Krishna Kurapati wrote:
>>> Currently the DWC3 driver supports only single port controller
>>> which requires at most one HS and one SS PHY.
>>
>> Add note here that multi-port is for host mode for clarity.
>>
>>>
>>> But the DWC3 USB controller can be connected to multiple ports and
>>> each port can have their own PHYs. Each port of the multiport
>>> controller can either be HS+SS capable or HS only capable
>>> Proper quantification of them is required to modify GUSB2PHYCFG
>>> and GUSB3PIPECTL registers appropriately.
>>>
>>> Add support for detecting, obtaining and configuring phy's supported
>>> by a multiport controller and limit the max number of ports
>>> supported to 4.
>>>
>>> Signed-off-by: Harsh Agarwal <quic_harshq@quicinc.com>
>>> Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
>>> ---
>>>   drivers/usb/dwc3/core.c | 304 +++++++++++++++++++++++++++++-----------
>>>   drivers/usb/dwc3/core.h |  15 +-
>>>   drivers/usb/dwc3/drd.c  |  14 +-
>>>   3 files changed, 244 insertions(+), 89 deletions(-)
>>>
>>> diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
>>> index 476b63618511..7e0a9a598dfd 100644
>>> --- a/drivers/usb/dwc3/core.c
>>> +++ b/drivers/usb/dwc3/core.c
>>> @@ -120,7 +120,7 @@ static void __dwc3_set_mode(struct work_struct *work)
>>>   {
>>>   	struct dwc3 *dwc = work_to_dwc(work);
>>>   	unsigned long flags;
>>> -	int ret;
>>> +	int ret, i;
>>
>> Can we declare variables in separate lines here and other places.
>>
>>>   	u32 reg;
>>>   	u32 desired_dr_role;
>>>   
>>> @@ -200,8 +200,10 @@ static void __dwc3_set_mode(struct work_struct *work)
>>>   		} else {
>>>   			if (dwc->usb2_phy)
>>>   				otg_set_vbus(dwc->usb2_phy->otg, true);
>>> -			phy_set_mode(dwc->usb2_generic_phy, PHY_MODE_USB_HOST);
>>> -			phy_set_mode(dwc->usb3_generic_phy, PHY_MODE_USB_HOST);
>>> +			for (i = 0; i < dwc->num_ports; i++) {
> 
> BTW, is num_ports the total of usb2 + usb3 ports?
Hi Thinh,

   No, num_ports is just the total number of hw usb ports present 
(presuming each port is hs capable, this is just the number of HS Phy's 
available).

Regards,
KRishna,
> 
>>> +				phy_set_mode(dwc->usb2_generic_phy[i], PHY_MODE_USB_HOST);
>>> +				phy_set_mode(dwc->usb3_generic_phy[i], PHY_MODE_USB_HOST);
>>> +			}
>>>   			if (dwc->dis_split_quirk) {
> 
> Thanks,
> Thinh