Re: [PATCH 5/5] arm64: dts: qcom: sm7225-fairphone-fp4: Enable USB role switching

[Bryan O'Donoghue <bryan.odonoghue@linaro.org>]

On 22/03/2024 08:01, Luca Weiss wrote:
> Configure the Type-C and VBUS regulator on PM7250B and wire it up to the
> USB PHY, so that USB role and orientation switching works.
> 
> Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
> ---
> With this patch I'm not quite sure if the 'ports' are connected
> correctly, though functionally everything appears to work fine.
> 
> On some other SoCs port@1 in qmpphy and a second port in dwc3 are
> connected together also - one port of USB 2.0 HS, one for USB 3.0 SS.
> 
> Here I'm following sm8250's solution. Also checking the binding doc
> doesn't reveal anything useful.

I don't see a redriver on your schematics which appears to be the only 
big difference to the qrb5165 reference.

https://www.fairphone.com/wp-content/uploads/2022/09/FP4_Information-for-repairers-and-recyclers.pdf


> ---
>   arch/arm64/boot/dts/qcom/sm6350.dtsi              | 25 ++++++++++
>   arch/arm64/boot/dts/qcom/sm7225-fairphone-fp4.dts | 57 ++++++++++++++++++++++-
>   2 files changed, 81 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
> index 24bcec3366ef..b267500467f0 100644
> --- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
> @@ -1686,6 +1686,27 @@ usb_1_qmpphy: phy@88e8000 {
>   			#phy-cells = <1>;
>   
>   			status = "disabled";
> +
> +			ports {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				port@0 {
> +					reg = <0>;
> +
> +					usb_1_qmpphy_out: endpoint {};
> +				};
> +
> +				port@1 {
> +					reg = <1>;
> +				};
> +
> +				port@2 {
> +					reg = <2>;
> +
> +					usb_1_qmpphy_dp_in: endpoint {};
> +				};
> +			};
>   		};
>   
>   		dc_noc: interconnect@9160000 {
> @@ -1861,6 +1882,10 @@ usb_1_dwc3: usb@a600000 {
>   				snps,hird-threshold = /bits/ 8 <0x10>;
>   				phys = <&usb_1_hsphy>, <&usb_1_qmpphy QMP_USB43DP_USB3_PHY>;
>   				phy-names = "usb2-phy", "usb3-phy";
> +
> +				port {
> +					usb_1_role_switch_out: endpoint {};
> +				};
>   			};
>   		};
>   
> diff --git a/arch/arm64/boot/dts/qcom/sm7225-fairphone-fp4.dts b/arch/arm64/boot/dts/qcom/sm7225-fairphone-fp4.dts
> index bc67e8c1fe4d..104f23ec322d 100644
> --- a/arch/arm64/boot/dts/qcom/sm7225-fairphone-fp4.dts
> +++ b/arch/arm64/boot/dts/qcom/sm7225-fairphone-fp4.dts
> @@ -19,6 +19,7 @@
>   #include <dt-bindings/leds/common.h>
>   #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
>   #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> +#include <dt-bindings/usb/pd.h>
>   #include "sm7225.dtsi"
>   #include "pm6150l.dtsi"
>   #include "pm6350.dtsi"
> @@ -543,6 +544,50 @@ conn-therm@1 {
>   	};
>   };
>   
> +&pm7250b_typec {
> +	vdd-pdphy-supply = <&vreg_l3a>;
> +
> +	status = "okay";
> +
> +	connector {
> +		compatible = "usb-c-connector";
> +
> +		power-role = "source";
> +		data-role = "dual";
> +		self-powered;
> +
> +		source-pdos = <PDO_FIXED(5000, 1500,
> +					 PDO_FIXED_DUAL_ROLE |
> +					 PDO_FIXED_USB_COMM |
> +					 PDO_FIXED_DATA_SWAP)>;
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port@0 {
> +				reg = <0>;
> +				pm7250b_role_switch_in: endpoint {
> +					remote-endpoint = <&usb_1_role_switch_out>;
> +				};
> +			};
> +
> +			port@1 {
> +				reg = <1>;
> +				pm7250b_typec_mux_in: endpoint {
> +					remote-endpoint = <&usb_1_qmpphy_out>;
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&pm7250b_vbus {
> +	regulator-min-microamp = <500000>;
> +	regulator-max-microamp = <1500000>;
> +	status = "okay";
> +};
> +
>   &pmk8350_rtc {
>   	status = "okay";
>   };
> @@ -726,7 +771,12 @@ &usb_1 {
>   
>   &usb_1_dwc3 {
>   	maximum-speed = "super-speed";
> -	dr_mode = "peripheral";
> +	dr_mode = "otg";
> +	usb-role-switch;
> +};
> +
> +&usb_1_role_switch_out {
> +	remote-endpoint = <&pm7250b_role_switch_in>;
>   };
>   
>   &usb_1_hsphy {
> @@ -740,10 +790,15 @@ &usb_1_hsphy {
>   &usb_1_qmpphy {
>   	vdda-phy-supply = <&vreg_l22a>;
>   	vdda-pll-supply = <&vreg_l16a>;
> +	orientation-switch;
>   
>   	status = "okay";
>   };
>   
> +&usb_1_qmpphy_out {
> +	remote-endpoint = <&pm7250b_typec_mux_in>;
> +};
> +
>   &wifi {
>   	vdd-0.8-cx-mx-supply = <&vreg_l4a>;
>   	vdd-1.8-xo-supply = <&vreg_l7a>;
> 

This looks consistent with 8250

Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>