Linux USB
 help / color / mirror / Atom feed
From: sashiko-bot@kernel.org
To: "Birger Koblitz" <mail@birger-koblitz.de>
Cc: linux-usb@vger.kernel.org
Subject: Re: [PATCH net-next v19 02/13] phylib: Add support for PHYs with broken forced mode
Date: Sun, 11 Oct 2026 04:54:56 +0000	[thread overview]
Message-ID: <sashiko-outbox-167014@kernel.org> (raw)
In-Reply-To: <20261010-ax88179a-v19-2-7475173cfb56@birger-koblitz.de>

Thank you for your contribution! Sashiko AI review found 2 potential issue(s) to consider:
- [High] phy: C45 MDIO writes falsely trigger C22 register handlers corrupting state
- [High] phylib: NULL pointer deref due to TOCTOU race on phydev->drv
--

commit f3ec63e34d550025dac6b66482995851d8d99969
Author: Birger Koblitz <mail@birger-koblitz.de>

phylib: Add support for PHYs with broken forced mode

This commit adds support for PHYs which only support auto-negotiated speed
modes. This prevents a kernel warning and stack-trace within the
phy_state_machine when PHYs return -EOPNOTSUPP from config_aneg() because
they do not support forced modes.

> diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
> --- a/drivers/net/phy/phy.c
> +++ b/drivers/net/phy/phy.c

[ ... ]

> @@ -354,6 +354,9 @@ int phy_mii_ioctl(struct phy_device *phydev, struct ifreq *ifr, int cmd)
>  			switch (devad) {
>  			case MII_BMCR:
>  				if ((val & (BMCR_RESET | BMCR_ANENABLE)) == 0) {
> +					if (phydev->drv &&
> +					    (phydev->drv->flags & PHY_BROKEN_FORCED))
> +						return -EOPNOTSUPP;

[Severity: High]
Can this unlocked check on phydev->drv lead to a NULL pointer dereference?

If a concurrent sysfs unbind calls phy_remove() and sets phydev->drv = NULL
without holding rtnl_lock or phydev->lock, the compiler might fetch
phydev->drv to verify it is non-NULL, and then fetch it again to read flags.
This double-fetch could result in a NULL pointer dereference if the pointer
is cleared between the two operations.

Also, for C45 accesses in phy_mii_ioctl(), devad holds the MMD address but
is matched against C22 register definitions like MII_BMCR (which is 0). 

Does adding this early return mean a C45 write to MMD 0 (with zeroed reset
and anenable bits) will now incorrectly hit this C22 handler and fail with
-EOPNOTSUPP?

[ ... ]

> @@ -1190,6 +1193,10 @@ int phy_ethtool_ksettings_set(struct phy_device *phydev,
>  	      duplex != DUPLEX_FULL)))
>  		return -EINVAL;
>  
> +	if (autoneg == AUTONEG_DISABLE && phydev->drv &&
> +	    (phydev->drv->flags & PHY_BROKEN_FORCED))
> +		return -EOPNOTSUPP;

[Severity: High]
Does this present the same time-of-check to time-of-use race as above?

A sysfs unbind could set phydev->drv to NULL between the NULL check and the
flags dereference, since ethtool operations and unbind operations do not
share a common lock here.

> +
>  	mutex_lock(&phydev->lock);
>  	phydev->autoneg = autoneg;

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20261010-ax88179a-v19-0-7475173cfb56@birger-koblitz.de?part=2

  reply	other threads:[~2026-10-11  4:54 UTC|newest]

Thread overview: 30+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-10-10  4:54 [PATCH net-next v19 00/13] ax88179_178a: Add support for AX88179A-based chips Birger Koblitz
2026-10-10  4:54 ` [PATCH net-next v19 01/13] phylink: Add phylink_mac_interrupt Birger Koblitz
2026-10-11  4:54   ` sashiko-bot
2026-10-11  5:32     ` Birger Koblitz
2026-10-10  4:54 ` [PATCH net-next v19 02/13] phylib: Add support for PHYs with broken forced mode Birger Koblitz
2026-10-11  4:54   ` sashiko-bot [this message]
2026-10-10  4:54 ` [PATCH net-next v19 03/13] ax88179_178a: Split driver into library and device specific code Birger Koblitz
2026-10-11  4:54   ` sashiko-bot
2026-10-10  4:54 ` [PATCH net-next v19 04/13] ax88179_178a: Add HW support for AX179A-based chips Birger Koblitz
2026-10-11  4:54   ` sashiko-bot
2026-10-10  4:54 ` [PATCH net-next v19 05/13] ax88179_178a: Add EEE configuration support for AX88179A MACs Birger Koblitz
2026-10-11  4:54   ` sashiko-bot
2026-10-10  4:54 ` [PATCH net-next v19 06/13] ax88179_178a: Add EEE configuration support for AX88179A PHYs Birger Koblitz
2026-10-11  4:54   ` sashiko-bot
2026-10-10  4:54 ` [PATCH net-next v19 07/13] ax88179_178a: Add VLAN offload support for AX88179A Birger Koblitz
2026-10-11  4:54   ` sashiko-bot
2026-10-10  4:54 ` [PATCH net-next v19 08/13] ax88179_178a: Add AX179A/AX279 multicast configuration Birger Koblitz
2026-10-11  4:54   ` sashiko-bot
2026-10-10  4:54 ` [PATCH net-next v19 09/13] ax88179_178a: Add Suspend/resume support for AX88179A/772D/279 Birger Koblitz
2026-10-11  4:54   ` sashiko-bot
2026-10-10  4:54 ` [PATCH net-next v19 10/13] ax88179_178a: Add ethtool get_drvinfo Birger Koblitz
2026-10-11  4:54   ` sashiko-bot
2026-10-10  4:54 ` [PATCH net-next v19 11/13] ax88179_178a: Update driver name and information Birger Koblitz
2026-10-11  4:54   ` sashiko-bot
2026-10-10  4:54 ` [PATCH net-next v19 12/13] ax88179_178a: Add support for AX88179A/772D/279 EEPROM access Birger Koblitz
2026-10-11  4:55   ` sashiko-bot
2026-10-10  4:54 ` [PATCH net-next v19 13/13] ax88796b: Add support for AX88772D, AX88179A and AX88279 Birger Koblitz
2026-10-11  4:55   ` sashiko-bot
2026-10-10  6:20 ` [PATCH v19 0/13] ax88179_178a: Add support for AX88179A-based chips Jianhui Xu
2026-10-10  7:42   ` Birger Koblitz

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=sashiko-outbox-167014@kernel.org \
    --to=sashiko-bot@kernel.org \
    --cc=linux-usb@vger.kernel.org \
    --cc=mail@birger-koblitz.de \
    --cc=sashiko-reviews@lists.linux.dev \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox