From: Leela Krishna Amudala <l.krishna@samsung.com>
To: linux-samsung-soc@vger.kernel.org, kgene.kim@samsung.com, wim@iguana.be
Cc: t.figa@samsung.com, devicetree@vger.kernel.org,
dianders@chromium.org, linux-watchdog@vger.kernel.org,
cpgs@samsung.com, sachin.kamat@linaro.org
Subject: [PATCH V5 3/3] watchdog: s3c2410_wdt: use syscon regmap interface to configure pmu register
Date: Thu, 31 Oct 2013 11:30:50 +0530 [thread overview]
Message-ID: <1383199250-15405-4-git-send-email-l.krishna@samsung.com> (raw)
In-Reply-To: <1383199250-15405-1-git-send-email-l.krishna@samsung.com>
The syscon regmap interface is used to configure AUTOMATIC_WDT_RESET_DISABLE
and MASK_WDT_RESET_REQUEST registers of PMU to mask/unmask enable/disable of
watchdog in probe and s2r scenarios.
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
---
.../devicetree/bindings/watchdog/samsung-wdt.txt | 22 ++-
drivers/watchdog/s3c2410_wdt.c | 150 +++++++++++++++++---
2 files changed, 154 insertions(+), 18 deletions(-)
diff --git a/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt
index 2aa486c..0b8aa4b 100644
--- a/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt
+++ b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt
@@ -5,10 +5,30 @@ after a preset amount of time during which the WDT reset event has not
occurred.
Required properties:
-- compatible : should be "samsung,s3c2410-wdt"
+- compatible : should be one among the following
+ (a) "samsung,s3c2410-wdt" for Exynos4 and previous SoCs
+ (b) "samsung,exynos5250-wdt" for Exynos5250
+ (c) "samsung,exynos5420-wdt" for Exynos5420
+
- reg : base physical address of the controller and length of memory mapped
region.
- interrupts : interrupt number to the cpu.
+- samsung,syscon-phandle : reference to syscon node (This property required only
+ in case of compatible being "samsung,exynos5250-wdt" or "samsung,exynos5420-wdt".
+ In case of Exynos5250 and 5420 this property points to syscon node holding the PMU
+ base address)
Optional properties:
- timeout-sec : contains the watchdog timeout in seconds.
+
+Example:
+
+watchdog@101D0000 {
+ compatible = "samsung,exynos5250-wdt";
+ reg = <0x101D0000 0x100>;
+ interrupts = <0 42 0>;
+ clocks = <&clock 336>;
+ clock-names = "watchdog";
+ samsung,sysreg = <&pmu_sys_reg>;
+ status = "okay";
+};
diff --git a/drivers/watchdog/s3c2410_wdt.c b/drivers/watchdog/s3c2410_wdt.c
index 23aad7c..235d160 100644
--- a/drivers/watchdog/s3c2410_wdt.c
+++ b/drivers/watchdog/s3c2410_wdt.c
@@ -41,6 +41,8 @@
#include <linux/slab.h>
#include <linux/err.h>
#include <linux/of.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
#define S3C2410_WTCON 0x00
#define S3C2410_WTDAT 0x04
@@ -61,6 +63,10 @@
#define CONFIG_S3C2410_WATCHDOG_ATBOOT (0)
#define CONFIG_S3C2410_WATCHDOG_DEFAULT_TIME (15)
+#define WDT_DISABLE_REG_OFFSET 0x0408
+#define WDT_MASK_RESET_REG_OFFSET 0x040c
+#define QUIRK_NEEDS_PMU_CONFIG (1 << 0)
+
static bool nowayout = WATCHDOG_NOWAYOUT;
static int tmr_margin;
static int tmr_atboot = CONFIG_S3C2410_WATCHDOG_ATBOOT;
@@ -84,18 +90,61 @@ MODULE_PARM_DESC(soft_noboot, "Watchdog action, set to 1 to ignore reboots, "
"0 to reboot (default 0)");
MODULE_PARM_DESC(debug, "Watchdog debug, set to >1 for debug (default 0)");
+struct s3c2410_wdt_variant {
+ int disable_reg;
+ int mask_reset_reg;
+ int mask_bit;
+ u32 quirks;
+};
+
struct s3c2410_wdt {
- struct device *dev;
- struct clk *clock;
- void __iomem *reg_base;
- unsigned int count;
- spinlock_t lock;
- unsigned long wtcon_save;
- unsigned long wtdat_save;
- struct watchdog_device wdt_device;
- struct notifier_block freq_transition;
+ struct device *dev;
+ struct clk *clock;
+ void __iomem *reg_base;
+ unsigned int count;
+ spinlock_t lock;
+ unsigned long wtcon_save;
+ unsigned long wtdat_save;
+ struct watchdog_device wdt_device;
+ struct notifier_block freq_transition;
+ struct s3c2410_wdt_variant *pmu_config;
+ struct regmap *pmureg;
+};
+
+#ifdef CONFIG_OF
+static struct s3c2410_wdt_variant pmu_config_s3c2410 = {
+ .disable_reg = 0x0,
+ .mask_reset_reg = 0x0,
+ .mask_bit = 0,
+ .quirks = 0
};
+static struct s3c2410_wdt_variant pmu_config_5250 = {
+ .disable_reg = WDT_DISABLE_REG_OFFSET,
+ .mask_reset_reg = WDT_MASK_RESET_REG_OFFSET,
+ .mask_bit = 20,
+ .quirks = QUIRK_NEEDS_PMU_CONFIG
+};
+
+static struct s3c2410_wdt_variant pmu_config_5420 = {
+ .disable_reg = WDT_DISABLE_REG_OFFSET,
+ .mask_reset_reg = WDT_MASK_RESET_REG_OFFSET,
+ .mask_bit = 0,
+ .quirks = QUIRK_NEEDS_PMU_CONFIG
+};
+
+static const struct of_device_id s3c2410_wdt_match[] = {
+ { .compatible = "samsung,s3c2410-wdt",
+ .data = (struct s3c2410_wdt_variant *) &pmu_config_s3c2410 },
+ { .compatible = "samsung,exynos5250-wdt",
+ .data = (struct s3c2410_wdt_variant *) &pmu_config_5250 },
+ { .compatible = "samsung,exynos5420-wdt",
+ .data = (struct s3c2410_wdt_variant *) &pmu_config_5420 },
+ {},
+};
+MODULE_DEVICE_TABLE(of, s3c2410_wdt_match);
+#endif
+
/* watchdog control routines */
#define DBG(fmt, ...) \
@@ -111,6 +160,47 @@ static inline struct s3c2410_wdt *freq_to_wdt(struct notifier_block *nb)
return container_of(nb, struct s3c2410_wdt, freq_transition);
}
+static void s3c2410wdt_mask_and_disable_reset(int mask, struct s3c2410_wdt *wdt)
+{
+ int ret;
+
+ if (mask) {
+ ret = regmap_update_bits(wdt->pmureg,
+ wdt->pmu_config->disable_reg,
+ (1 << wdt->pmu_config->mask_bit),
+ (1 << wdt->pmu_config->mask_bit));
+ if (ret < 0) {
+ dev_err(wdt->dev, "failed to update reg(%d)\n", ret);
+ return;
+ }
+ ret = regmap_update_bits(wdt->pmureg,
+ wdt->pmu_config->mask_reset_reg,
+ (1 << wdt->pmu_config->mask_bit),
+ (1 << wdt->pmu_config->mask_bit));
+ if (ret < 0) {
+ dev_err(wdt->dev, "failed to update reg(%d)\n", ret);
+ return;
+ }
+ } else {
+ ret = regmap_update_bits(wdt->pmureg,
+ wdt->pmu_config->disable_reg,
+ (1 << wdt->pmu_config->mask_bit),
+ (0 << wdt->pmu_config->mask_bit));
+ if (ret < 0) {
+ dev_err(wdt->dev, "failed to update reg(%d)\n", ret);
+ return;
+ }
+ ret = regmap_update_bits(wdt->pmureg,
+ wdt->pmu_config->mask_reset_reg,
+ (1 << wdt->pmu_config->mask_bit),
+ (0 << wdt->pmu_config->mask_bit));
+ if (ret < 0) {
+ dev_err(wdt->dev, "failed to update reg(%d)\n", ret);
+ return;
+ }
+ }
+}
+
static int s3c2410wdt_keepalive(struct watchdog_device *wdd)
{
struct s3c2410_wdt *wdt = watchdog_get_drvdata(wdd);
@@ -332,6 +422,15 @@ static inline void s3c2410wdt_cpufreq_deregister(struct s3c2410_wdt *wdt)
}
#endif
+/* s3c2410_get_wdt_driver_data */
+static inline struct s3c2410_wdt_variant *
+get_wdt_drv_data(struct platform_device *pdev)
+{
+ const struct of_device_id *match;
+ match = of_match_node(s3c2410_wdt_match, pdev->dev.of_node);
+ return (struct s3c2410_wdt_variant *)match->data;
+}
+
static int s3c2410wdt_probe(struct platform_device *pdev)
{
struct device *dev;
@@ -354,6 +453,16 @@ static int s3c2410wdt_probe(struct platform_device *pdev)
spin_lock_init(&wdt->lock);
wdt->wdt_device = s3c2410_wdd;
+ wdt->pmu_config = (struct s3c2410_wdt_variant *) get_wdt_drv_data(pdev);
+ if (wdt->pmu_config->quirks & QUIRK_NEEDS_PMU_CONFIG) {
+ wdt->pmureg = syscon_regmap_lookup_by_phandle(dev->of_node,
+ "samsung,syscon-phandle");
+ if (IS_ERR(wdt->pmureg)) {
+ dev_err(dev, "syscon regmap lookup failed.\n");
+ return PTR_ERR(wdt->pmureg);
+ }
+ }
+
wdt_irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
if (wdt_irq == NULL) {
dev_err(dev, "no irq resource specified\n");
@@ -444,6 +553,9 @@ static int s3c2410wdt_probe(struct platform_device *pdev)
(wtcon & S3C2410_WTCON_RSTEN) ? "en" : "dis",
(wtcon & S3C2410_WTCON_INTEN) ? "en" : "dis");
+ if (wdt->pmu_config->quirks & QUIRK_NEEDS_PMU_CONFIG)
+ s3c2410wdt_mask_and_disable_reset(0, wdt);
+
return 0;
err_cpufreq:
@@ -461,6 +573,9 @@ static int s3c2410wdt_remove(struct platform_device *dev)
{
struct s3c2410_wdt *wdt = platform_get_drvdata(dev);
+ if (wdt->pmu_config->quirks & QUIRK_NEEDS_PMU_CONFIG)
+ s3c2410wdt_mask_and_disable_reset(1, wdt);
+
watchdog_unregister_device(&wdt->wdt_device);
s3c2410wdt_cpufreq_deregister(wdt);
@@ -475,6 +590,9 @@ static void s3c2410wdt_shutdown(struct platform_device *dev)
{
struct s3c2410_wdt *wdt = platform_get_drvdata(dev);
+ if (wdt->pmu_config->quirks & QUIRK_NEEDS_PMU_CONFIG)
+ s3c2410wdt_mask_and_disable_reset(1, wdt);
+
s3c2410wdt_stop(&wdt->wdt_device);
}
@@ -488,6 +606,9 @@ static int s3c2410wdt_suspend(struct device *dev)
wdt->wtcon_save = readl(wdt->reg_base + S3C2410_WTCON);
wdt->wtdat_save = readl(wdt->reg_base + S3C2410_WTDAT);
+ if (wdt->pmu_config->quirks & QUIRK_NEEDS_PMU_CONFIG)
+ s3c2410wdt_mask_and_disable_reset(1, wdt);
+
/* Note that WTCNT doesn't need to be saved. */
s3c2410wdt_stop(&wdt->wdt_device);
@@ -503,6 +624,9 @@ static int s3c2410wdt_resume(struct device *dev)
writel(wdt->wtdat_save, wdt->reg_base + S3C2410_WTCNT);/* Reset count */
writel(wdt->wtcon_save, wdt->reg_base + S3C2410_WTCON);
+ if (wdt->pmu_config->quirks & QUIRK_NEEDS_PMU_CONFIG)
+ s3c2410wdt_mask_and_disable_reset(0, wdt);
+
dev_info(dev, "watchdog %sabled\n",
(wdt->wtcon_save & S3C2410_WTCON_ENABLE) ? "en" : "dis");
@@ -513,14 +637,6 @@ static int s3c2410wdt_resume(struct device *dev)
static SIMPLE_DEV_PM_OPS(s3c2410wdt_pm_ops, s3c2410wdt_suspend,
s3c2410wdt_resume);
-#ifdef CONFIG_OF
-static const struct of_device_id s3c2410_wdt_match[] = {
- { .compatible = "samsung,s3c2410-wdt" },
- {},
-};
-MODULE_DEVICE_TABLE(of, s3c2410_wdt_match);
-#endif
-
static struct platform_driver s3c2410wdt_driver = {
.probe = s3c2410wdt_probe,
.remove = s3c2410wdt_remove,
--
1.7.10.4
next prev parent reply other threads:[~2013-10-31 5:40 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-10-31 6:00 [PATCH V5 0/3] Add watchdog DT nodes and use syscon regmap interfac to configure pmu registers Leela Krishna Amudala
2013-10-31 6:00 ` [PATCH V5 1/3] ARM: dts: Add pmu sysreg node to Exynos5 dtsi file Leela Krishna Amudala
2013-10-31 12:06 ` Tomasz Figa
2013-10-31 6:00 ` [PATCH V5 2/3] ARM: dts: add watchdog device nodes for Exynos5250 and Exynos5420 Leela Krishna Amudala
2013-10-31 12:09 ` Tomasz Figa
2013-10-31 6:00 ` Leela Krishna Amudala [this message]
2013-10-31 12:29 ` [PATCH V5 3/3] watchdog: s3c2410_wdt: use syscon regmap interface to configure pmu register Tomasz Figa
2013-10-31 13:29 ` Guenter Roeck
2013-10-31 6:57 ` [PATCH V5 0/3] Add watchdog DT nodes and use syscon regmap interfac to configure pmu registers Sachin Kamat
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1383199250-15405-4-git-send-email-l.krishna@samsung.com \
--to=l.krishna@samsung.com \
--cc=cpgs@samsung.com \
--cc=devicetree@vger.kernel.org \
--cc=dianders@chromium.org \
--cc=kgene.kim@samsung.com \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=linux-watchdog@vger.kernel.org \
--cc=sachin.kamat@linaro.org \
--cc=t.figa@samsung.com \
--cc=wim@iguana.be \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox