From: Alexandre Mergnat <amergnat@baylibre.com>
To: Catalin Marinas <catalin.marinas@arm.com>,
Will Deacon <will@kernel.org>,
Wim Van Sebroeck <wim@linux-watchdog.org>,
Guenter Roeck <linux@roeck-us.net>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Matthias Brugger <matthias.bgg@gmail.com>,
AngeloGioacchino Del Regno
<angelogioacchino.delregno@collabora.com>,
Conor Dooley <conor+dt@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, linux-watchdog@vger.kernel.org,
devicetree@vger.kernel.org, linux-mediatek@lists.infradead.org,
Alexandre Mergnat <amergnat@baylibre.com>,
Kevin Hilman <khilman@baylibre.com>
Subject: [PATCH v8 05/10] arm64: dts: mediatek: add mmc support for mt8365-evk
Date: Thu, 25 May 2023 10:33:14 +0200 [thread overview]
Message-ID: <20230203-evk-board-support-v8-5-7019f3fd0adf@baylibre.com> (raw)
In-Reply-To: <20230203-evk-board-support-v8-0-7019f3fd0adf@baylibre.com>
- Add EMMC support on mmc0 (internal memory)
- Add SD-UHS support on mmc1 (external memory)
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Alexandre Mergnat <amergnat@baylibre.com>
---
arch/arm64/boot/dts/mediatek/mt8365-evk.dts | 138 ++++++++++++++++++++++++++++
1 file changed, 138 insertions(+)
diff --git a/arch/arm64/boot/dts/mediatek/mt8365-evk.dts b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
index 6074aa9c1c3e..6e2f3601509e 100644
--- a/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8365-evk.dts
@@ -95,6 +95,42 @@ &i2c0 {
status = "okay";
};
+&mmc0 {
+ assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL>;
+ assigned-clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>;
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ cap-mmc-hw-reset;
+ hs400-ds-delay = <0x12012>;
+ max-frequency = <200000000>;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ no-sd;
+ no-sdio;
+ non-removable;
+ pinctrl-0 = <&mmc0_default_pins>;
+ pinctrl-1 = <&mmc0_uhs_pins>;
+ pinctrl-names = "default", "state_uhs";
+ vmmc-supply = <&mt6357_vemc_reg>;
+ vqmmc-supply = <&mt6357_vio18_reg>;
+ status = "okay";
+};
+
+&mmc1 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cd-gpios = <&pio 76 GPIO_ACTIVE_LOW>;
+ max-frequency = <200000000>;
+ pinctrl-0 = <&mmc1_default_pins>;
+ pinctrl-1 = <&mmc1_uhs_pins>;
+ pinctrl-names = "default", "state_uhs";
+ sd-uhs-sdr104;
+ sd-uhs-sdr50;
+ vmmc-supply = <&mt6357_vmch_reg>;
+ vqmmc-supply = <&mt6357_vmc_reg>;
+ status = "okay";
+};
+
&mt6357_pmic {
interrupts-extended = <&pio 145 IRQ_TYPE_LEVEL_HIGH>;
interrupt-controller;
@@ -118,6 +154,108 @@ pins {
};
};
+ mmc0_default_pins: mmc0-default-pins {
+ clk-pins {
+ pinmux = <MT8365_PIN_99_MSDC0_CLK__FUNC_MSDC0_CLK>;
+ bias-pull-down;
+ };
+
+ cmd-dat-pins {
+ pinmux = <MT8365_PIN_103_MSDC0_DAT0__FUNC_MSDC0_DAT0>,
+ <MT8365_PIN_102_MSDC0_DAT1__FUNC_MSDC0_DAT1>,
+ <MT8365_PIN_101_MSDC0_DAT2__FUNC_MSDC0_DAT2>,
+ <MT8365_PIN_100_MSDC0_DAT3__FUNC_MSDC0_DAT3>,
+ <MT8365_PIN_96_MSDC0_DAT4__FUNC_MSDC0_DAT4>,
+ <MT8365_PIN_95_MSDC0_DAT5__FUNC_MSDC0_DAT5>,
+ <MT8365_PIN_94_MSDC0_DAT6__FUNC_MSDC0_DAT6>,
+ <MT8365_PIN_93_MSDC0_DAT7__FUNC_MSDC0_DAT7>,
+ <MT8365_PIN_98_MSDC0_CMD__FUNC_MSDC0_CMD>;
+ input-enable;
+ bias-pull-up;
+ };
+
+ rst-pins {
+ pinmux = <MT8365_PIN_97_MSDC0_RSTB__FUNC_MSDC0_RSTB>;
+ bias-pull-up;
+ };
+ };
+
+ mmc0_uhs_pins: mmc0-uhs-pins {
+ clk-pins {
+ pinmux = <MT8365_PIN_99_MSDC0_CLK__FUNC_MSDC0_CLK>;
+ drive-strength = <MTK_DRIVE_10mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ cmd-dat-pins {
+ pinmux = <MT8365_PIN_103_MSDC0_DAT0__FUNC_MSDC0_DAT0>,
+ <MT8365_PIN_102_MSDC0_DAT1__FUNC_MSDC0_DAT1>,
+ <MT8365_PIN_101_MSDC0_DAT2__FUNC_MSDC0_DAT2>,
+ <MT8365_PIN_100_MSDC0_DAT3__FUNC_MSDC0_DAT3>,
+ <MT8365_PIN_96_MSDC0_DAT4__FUNC_MSDC0_DAT4>,
+ <MT8365_PIN_95_MSDC0_DAT5__FUNC_MSDC0_DAT5>,
+ <MT8365_PIN_94_MSDC0_DAT6__FUNC_MSDC0_DAT6>,
+ <MT8365_PIN_93_MSDC0_DAT7__FUNC_MSDC0_DAT7>,
+ <MT8365_PIN_98_MSDC0_CMD__FUNC_MSDC0_CMD>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_10mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+
+ ds-pins {
+ pinmux = <MT8365_PIN_104_MSDC0_DSL__FUNC_MSDC0_DSL>;
+ drive-strength = <MTK_DRIVE_10mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ rst-pins {
+ pinmux = <MT8365_PIN_97_MSDC0_RSTB__FUNC_MSDC0_RSTB>;
+ drive-strength = <MTK_DRIVE_10mA>;
+ bias-pull-up;
+ };
+ };
+
+ mmc1_default_pins: mmc1-default-pins {
+ cd-pins {
+ pinmux = <MT8365_PIN_76_CMDAT8__FUNC_GPIO76>;
+ bias-pull-up;
+ };
+
+ clk-pins {
+ pinmux = <MT8365_PIN_88_MSDC1_CLK__FUNC_MSDC1_CLK>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ cmd-dat-pins {
+ pinmux = <MT8365_PIN_89_MSDC1_DAT0__FUNC_MSDC1_DAT0>,
+ <MT8365_PIN_90_MSDC1_DAT1__FUNC_MSDC1_DAT1>,
+ <MT8365_PIN_91_MSDC1_DAT2__FUNC_MSDC1_DAT2>,
+ <MT8365_PIN_92_MSDC1_DAT3__FUNC_MSDC1_DAT3>,
+ <MT8365_PIN_87_MSDC1_CMD__FUNC_MSDC1_CMD>;
+ input-enable;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+ };
+
+ mmc1_uhs_pins: mmc1-uhs-pins {
+ clk-pins {
+ pinmux = <MT8365_PIN_88_MSDC1_CLK__FUNC_MSDC1_CLK>;
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ cmd-dat-pins {
+ pinmux = <MT8365_PIN_89_MSDC1_DAT0__FUNC_MSDC1_DAT0>,
+ <MT8365_PIN_90_MSDC1_DAT1__FUNC_MSDC1_DAT1>,
+ <MT8365_PIN_91_MSDC1_DAT2__FUNC_MSDC1_DAT2>,
+ <MT8365_PIN_92_MSDC1_DAT3__FUNC_MSDC1_DAT3>,
+ <MT8365_PIN_87_MSDC1_CMD__FUNC_MSDC1_CMD>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+ };
+
uart0_pins: uart0-pins {
pins {
pinmux = <MT8365_PIN_35_URXD0__FUNC_URXD0>,
--
2.25.1
next prev parent reply other threads:[~2023-05-25 8:34 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-05-25 8:33 [PATCH v8 00/10] Improve the MT8365 SoC and EVK board support Alexandre Mergnat
2023-05-25 8:33 ` [PATCH v8 01/10] arm64: defconfig: enable MT6357 regulator Alexandre Mergnat
2023-05-30 13:28 ` Krzysztof Kozlowski
2023-05-25 8:33 ` [PATCH v8 02/10] arm64: defconfig: enable Mediatek PMIC key Alexandre Mergnat
2023-05-25 8:33 ` [PATCH v8 03/10] arm64: dts: mediatek: add watchdog support for mt8365 SoC Alexandre Mergnat
2023-05-25 8:33 ` [PATCH v8 04/10] arm64: dts: mediatek: add mt6357 PMIC support for mt8365-evk Alexandre Mergnat
2023-05-25 8:33 ` Alexandre Mergnat [this message]
2023-05-25 8:33 ` [PATCH v8 06/10] arm64: dts: mediatek: add usb controller " Alexandre Mergnat
2023-05-25 8:33 ` [PATCH v8 07/10] arm64: dts: mediatek: add ethernet " Alexandre Mergnat
2023-05-25 8:49 ` AngeloGioacchino Del Regno
2023-05-25 8:33 ` [PATCH v8 08/10] arm64: dts: mediatek: add OPP support for mt8365 SoC Alexandre Mergnat
2023-05-25 8:33 ` [PATCH v8 09/10] arm64: dts: mediatek: add cpufreq support for mt8365-evk Alexandre Mergnat
2023-05-25 8:33 ` [PATCH v8 10/10] arm64: dts: mediatek: Add CPU Idle support amergnat
2023-05-29 13:22 ` [PATCH v8 00/10] Improve the MT8365 SoC and EVK board support Matthias Brugger
2023-05-29 14:00 ` Alexandre Mergnat
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230203-evk-board-support-v8-5-7019f3fd0adf@baylibre.com \
--to=amergnat@baylibre.com \
--cc=angelogioacchino.delregno@collabora.com \
--cc=catalin.marinas@arm.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=khilman@baylibre.com \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=linux-watchdog@vger.kernel.org \
--cc=linux@roeck-us.net \
--cc=matthias.bgg@gmail.com \
--cc=robh+dt@kernel.org \
--cc=will@kernel.org \
--cc=wim@linux-watchdog.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox